Search Documents

By JOHN G. RAYNER

An examination was made of the filtration characteristics of a haematite slurry using a range of polyacrylamide based flocculants in solutions containing up to 3 per cent sodium chloride. The polymers used were "high" and "Iow" molecular weight and had from 0 to 40 per cent charged groups.Increasing charge density tends to reduce the dose required to achieve optimum performance measured by filtration rate and by cake moisture. In general increased salt addition tends to increase the dosage required to achieve these optima. Both these observations result from the change in polymer extension and accord well with the bridging theory of flocculation.The dose required for optimal cake moisture is up to three times greater than that required for optimal filtration rate. This effect is reasonably consistent for all polymers studied and appears to be non-linearly dependent on salt concentration, with the difference being small at 0 and 3 per cent but quite significant at 1 per cent.

Jan 1, 1987

By Mauro Andrés Cerra Flórez

O presente estudo visa avaliar a resistência à corrosão de dois aços alto manganês com relação ao aço 9% Níquel em solução eletrólito 0,001M de H2SO4. Para esta pesquisa foram utilizados dois aços com teores de manganês de 22% e 26%, e a liga de aço 9% Níquel que é amplamente utilizada na indústria petroquímica. Os ensaios realizados para comparação da resistência à corrosão foram o monitoramento do potencial de circuito aberto (OCP) e polarização linear anódica. Foi escolhida a solução de H2SO4 pela presença do enxofre, oriundo dos campos de produção como impureza no gás natural. Foram utilizadas as técnicas de Microscopia Eletrônica de Varredura (MEV) e Espectroscopia de Energia Dispersiva de Raios-X (EDS) para a caracterização dos produtos de corrosão. Os resultados obtidos mostraram que os aços alto Manganês apresentaram valores similares de resistência à corrosão, mas ainda inferiores em relação ao aço 9% Níquel.

Oct 30, 2017

By Knevitt L. T

PART 1Details of Kiewa Scheme.Introduction.Topography.Preliminary Investigations.Geology.Description of Project.Details of Main Works.Main Transmission of Power.Construction Facilities.PART 2Underground Works.Summary of Projected Works.Administration.Labour.Surveying.Safety and Accident Prevention.Medical Attention and First Aid.PART 3No. 4 Head Race Tunnel.Summary.Geology.

Jan 1, 1950

By J. W. Paul

The material that composes the roof in coal mines differs in strength according to variations in its physical nature and characteristics. Some material such as limestone and massive sandstone, (free from slits) and carbonaceous shale or bone, will often remain in place in narrow work without the use of timber or other means of support, but in wide places the use of supports becomes a real necessity. Roof material composed of shale, fire clay or small laminations of sandstone, or shale or sandstone interspersed with laminations of thin coal, presents conditions that call for timber support in both narrow and wide work. However, in narrow work such unstable roof material may be taken down until the strata assume an arch that is self-supporting for overlying firm strata such as a roof coal, a touch weather-resisting, shale, sandstone, or limestone. The proper support of the roof in roadways used for haulage or travel adds to the economy of operation by preventing delays in transportation and increases the safety of those who travel these roadways.

Jan 1, 1930

By J. W. Thompson

LIMESTONE DEPOSITS. Limestone deposits that have not been demonstrated to be of such quality as to give them any substantial value over other limestone deposits of the same region, are not regarded as minerals. Gray Trust Co., In re, 47 Land Decisions 18, p. 20. OIL AS A MINERAL. Oil is a mineral substance and its removal will greatly impair the value of the land from which it is removed. Texas & Pacific Coal & Oil Co. v. Howard. Southwestern 735, p. 737. Tex. Clv. App. 212 OIL AND GAS AS MINERALS OWNERSHIP. Oil and gas are minerals and so long as they remain in place they belong to the owner of the land under which they are found and such owner has the right to explore for the oil and gas on or under his land and when found to remove and possess the same. Kimbley v. Luckey, Okla. - 179 Pacific 928, p. 831. OWNERSHIP OF MINERALS LACHES NO BAR. The owner of minerals in land can not be barred by laches for failing to assert his ownership where his title had not been ques- tioned and his right invaded. No lapse of time bars one's right to property and it is only in case his right has been invaded that it can be barred by laches.

Jan 1, 1920

By W. A. Grosh

Records show that much of the lead produced in the Upper Mississippi Valley lead-zinc field was taken from natural openings along crevice systems at shallow horizons or at the surface. During the early history of the district, the shallow deposits were worked intensively; but in recent years the production of lead, except as a byproduct of deeper mining for zinc ores, has not been significant. Considering the methods of early mining, the character of mineralization, and the fact that galena can still be found on the surface of the old digging areas, it was reasoned that enough mineralization might remain on and above bedrock to permit, through the use of modern equipment and methods, economical re-treatment of surface material in the digging areas.

Jan 1, 1960

By Tomás Guerrero M

El objetivo del presente texto es analizar historiográficamente la exploración de los yacimientos minerales durante el período de 1960 -1978. La selección de este período implica una revisión técnica como de descubrimiento. En este sentido, la exploración de minerales se basó en tres grupos: cobre, polimétalicos y no metálicos, donde la primera década revela una actividad de exploración realizada por el sector privado, mientras que los últimos años significa un crecimiento explosivo de la actividad estatal en la exploración de minerales.

Nov 20, 1978

By Loughnan FC

There are some thirteen laboratories in Australia in which coal petrological work is carried out on a consistent and routine basis. Applied coal petrological research is conducted by several institutions in different disciplines which can be grouped into four main categories:

Jan 1, 1989

By A. C. Fieldner, SIDNEY GOTTLIEB

This report summarizes the research and technologic work of the Bureau of Mines on coal and coal products from July 1, 1947, to July 1, 1948. It is the thirteenth of a series presenting resumes based largely upon publications issued during the year . In some instances , research and testing results , not otherwise available in published form , are presented . The individual publications given as footnote references herein will provide further detail to the interested reader . The period covered by this report was marked by an ever -mounting concern for the adequacy of the Nation's fuel resources and for fuel shortages arising from an increasing demand for fuels at home and abroad . Several reports appeared which delineated the place of synthetic liquid fuels in the future fuel technology and economy of the Nation , emphasized the fact that eventually the principal raw material for the production of such fuels will bet,5,6 coal, and described the progress made by the Bureau of Mines in developing processes for the production of synthetic liquid fuels . heard testimony along similar lines . Increased awareness of the fuels problems confronting the Nation led to an authorization by the 80th Congress for the erection of an anthracite research laboratory at Schuylkill Haven , Pa . , to house expanded Bureau of Mines research on anthracite . Design of the structure was well under way by the end of the fiscal year . ( See fig . 1. ) Looking forward to expansion of Bureau research on lignite , the 80th Congress heard testimony on the problems and programs of lignite research10, 11 as a prelude to authorizing the construction of a lignite research laboratory in North Dakota .

Aug 1, 1949

By Camila Oliveira de Souza

O material em estudo consistiu em um aço inoxidável austenítico 201LN, na forma de chapa com aproximadamente 5,00 mm de espessura na condição laminada a quente. As etapas de processamento adotadas neste estudo consistiram em laminação a temperatura ambiente e pré-resfriamento em salmoura, com o objetivo de avaliar a formação de martensita e evolução da resistência mecânica do material. As técnicas de caracterização utilizadas foram macro Dureza Rockwell C (HRC), Ferritoscopia e Difração de Raios-X (DRX). Os resultados preliminares mostraram que tanto a fração volumétrica de martensita formada, como a dureza, foram maiores nas amostras submetidas a maiores percentuais de redução e pré-resfriamento em salmoura.

Oct 30, 2017

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By Edward H. Robie

Jan 1, 1971

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

ANNUAL meeting of the Woman's Auxiliary of the American Institute of Mining and Metal-lurgical Engineers convened on Tuesday morn-ing, Feb. 20, the president, Mrs. H. W. Hardinge, presiding. President Hardinge, in opening the meet-ing, said: "I have the honor and great pleasure to welcome you to our seventh annual meeting. It has been a happy year, though I started in fear and trembling. My fear is partly gone and my trembling becomes less as time goes on. Never has a chairman had such splendid cooperation and harmony in her work; no. matter how much was asked nor what the task, I have always received the same answer, `We are with you, of course we can do it.' Often the road has been untried and the way full of snares, but we have all pulled together. Is it any wonder we have had a prosperous year? I cannot thank the governing -board and officers enough for their help." Mrs. Hardinge described her trip through the West last summer, during which she visited many of the local sections of the Auxiliary. She also spoke of the work of the Rossiter Raymond memorial library which has been started as an activity of the Woman's Auxiliary. Mrs. Reynders read the minutes of the last annual meeting, and Mrs. Kemp read the treasurer's report. The latter showed that on Feb. 1, 1922, there was a bank balance of $683.61 and on Feb. 10, 1923, the bal-ance was $947.93. Mrs. Westervelt expressed the sorrow of the Auxiliary for the death -of Mrs. Florence Howe Hall and of Mrs. Levi P. Holbrook.

Jan 4, 1923

By José Ramiro Esteves Ramos

Características microestruturais são determinantes para as propriedades não ôhmicas de materiais varistores, uma vez que elas se relacionam com o coeficiente de não linearidade das curvas U x I, com a capacidade de absorção de energia, e com o seu grau de confiabilidade. O presente trabalho tem por objetivo a análise composicional e microestrutural de um material varistor comercial a base de ZnO dopado com diversos óxidos, além de comparar a eficiência dos ataques químico e térmico para a visualização das imagens em MEV. Os resultados obtidos condizem com a literatura onde foi observada a predominância de grãos majoritariamente compostos por ZnO com a presença de segregações constituídas de diversos elementos e concentradas nos contornos de grão. Quanto aos ataques, foi notável uma melhor qualidade das imagens quando se adotou o ataque térmico do ponto de vista da visualização dos contornos de grão. O ataque químico, por sua vez, demonstrou ser mais eficiente na elucidação das fases segregadas e na revelação da porosidade do material varistor.

Aug 17, 2017

By B. P. Martinez

In response to a request from the President, the Department of the Interior joined with other agencies in a comprehensive study of the land and water resources of the New England-New York region. As part of this study, chemical engineers of the Bureau of Mines have visited 1,025 mineral-industries plants to inventory the waterborne wastes of mineral origin, discharged by the mineral industries of the New England-New York region. Four-hundred and sixty-two of these plants disposed their wastes to a public sewer of some type, but waste control remains a problem for moat of them. The 1,025 plants are discussed in main industry groups according to their production: Chemical and allied products. Stone, clay, and glass products. Iron and steel and their products (except machinery). Nonferrous metals and their products. Electrical machinery. Machinery (except electrical). Transportation equipment. Miscellaneous mineral industries.

Jan 1, 1956

By Tony Robles

"A new process is disclosed for the recovery of gold and/or silver values from activated carbon wherein they are adsorbed as cyanide complexes. A unique chemistry allows the new process to use mill process water containing an inexpensive, non-hazardous compound as the eluant. The new process has an elution period of 5 hours at 98°C. The gold in the eluant can be recovered by electrowinning or zinc precipitation. The new elution process is simple, reliable, and provides an eluted carbon that may not require thermal regeneration before reuse. Retrofitting the new process to existing processes such as Zadra, Anglo, and others will not require significant capital expenditures.IntroductionThe efficient and reliable elution process for gold/silver from activated carbon is a very important process in the gold mining industry. The most common techniques for elution of gold cyanide from activated carbon are the Zadra and Anglo procedures.Specialized elution techniques like the Micron and Acetonitrile processes have not been commercialized to significant extent probably due to relatively complex unit operations and expensive reagents.Important functions of the gold recovery circuit are:Efficiently recover gold/silver from the loaded carbon.Carbon is in good condition for reuse for optimum recovery.The pregnant solution is amenable to electrowinning or zinc precipitation to recover gold/silver from the solution.The whole process to be simple and short to reduce gold inventories.Present Elution ProcessesTable 1 shows some carbon elution processes that are available today. The two main elution processes used in the industry are: (1) the Zadra process, in which hot cyanide solution is circulated through an elution column and electrowinning cells; and (2) the Anglo American Research Laboratory (Anglo) process, consisting of a pretreatment step with caustic cyanide solution, followed by elution with deionized water."

Jan 1, 2000

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Martín Antonio Encinas‐Romero, Patricia Guerrero‐Germán, Jesús Leobardo Valenzuela‐García, José R. Parga‐Torres, María A. Bracamontes‐Landavazo, Agustín Gómez‐Alvarez

A study was carried out to process a sulfide mineral concentrate from Norwest of Mexico containing 97 g/t Au, 0.15% Cu, and 15% Fe. An oxidative acid pretreatment was investigated using ferric sulfate as oxidant, followed by leaching of gold with sodium cyanide. Scanning electron microscopy, SEM-EDS, and X-ray diffraction, XRD, the analysis confirms the presence of quartz and pyrite species. First, a leaching was carried out without pretreatment, at ambient conditions, T = 25 °C and P = 1 atm, obtaining only a 45.2% gold extraction. Once the presence of Fe and Cu sulfides had been confirmed, the Eh-pH diagrams were constructed for the Fe-S-H2O and Cu-S-H2O systems, where it is appreciated that pyrite and chalcocite can dissolve with high oxidation potentials and forming sulfur, oxidizing to sulfate at highly acidic conditions. The oxidized concentrate was neutralized and adjusted to pH > 10.5; it was leached at ambient conditions, at different particle sizes, 44, 37, and 26.5μm, achieving an Au extraction of 75% using a concentration of 0.5% NaCN, 26.5μm particle size, 20% solids, and P = 1atm. Then the oxidized material was subjected to different temperatures, 25, 50, and 70 °C, under the same conditions and obtaining Au extractions up to 92% at 70°C. Additionally, the leaching process was compared using an autoclave reactor at moderate pressures, obtaining an increase in the extraction of Au up to 98% in 2 h, at T = 70 °C and P = 0.62 MPa.

Jan 23, 2022

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modelling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. Three-dimensional numerical direct shear tests were conducted on the coupled FD-DE model of the combined rock-cemented rockfill (R-CRF) specimens with the frictional-bonded interface. With the microstructural parameters determined, the macro-mechanical properties of the interface of the coupled model were calibrated to well fit with the theoretical values of the combined specimen under the direct shear condition assumed according to the Mohr–Coulomb strength criterion. Evident elastoplastic shear behaviour was observed on the interfaces, and excellent agreement was attained between the shapes of the theoretical and simulated shear stress-displacement curves of the coupled models at different servo-controlled normal stresses. Particulate-scale force chains inside the DE model of the CRF specimen were highly consistent with the force contour on the FD model of the rock specimen, demonstrating the shear stress evolution of the coupled model at different shear displacements. Parametric studies verified the effects of the deformation properties of the interface parallel bonds on the shape of shear stress-displacement curves of the coupled models. The test results validated the feasibility and rationality of the coupled FD-DE method for modelling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modelling experience for investigating the shear behaviour at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

Nov 2, 2021