Search Documents

For small particles of niekel flotation eoncentrate (av. size 50 pm) the predominant heat transfer mechanism under suspension smelting conditions, prior to ignition, is conduction from the gas and not radiation from nearby hot bodies. Results of laboratory tests using gas temperatures 380-700°C and furnace wall temperatures 380-1100°C were in accord with heat transfer theory. In practieal flash smelters earlier ignition, and hence better utilization of the space in the shaft, would result from introduetion at the top of the shaft of gases hotter than the ignition temperature of 500-600°C.

Jan 1, 1979

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By D G. Miljak, J Khachan, B K. Schwitter

The performance of prototype magnetic resonance sensors suited to mineral measurement in conveyor, slurry or portable applications is described. The sensors can be positioned around conveyors and modified slurry pipes, providing deep penetration of the sensing field, relative insensitivity to ore surface conditions and high mineral discrimination. Measurements on slurry, concentrates and ores sourced from mine operations are presented for two applications. Firstly, the quantitative measurement of chalcopyrite in slurry was demonstrated in laboratory measurements. In a calibration test, a standard error of 0.1 wt per cent and detection limit of 0.3 wt per cent was obtained. Secondly, results were obtained for the discrimination of iron ore texture. Signals were readily observed using measurement integration times of seconds to several minutes, depending on ore material. The results demonstrate the feasibility of online quantitative analysis of selected minerals in processing applications using magnetic resonance.

Jan 1, 2008

By A J. H Newell

The background and the basis for conducting a Technical Due Diligence are discussed as well as the source information, typical studies and potential limitations. Typical short comings including ‘show-stoppers’ are presented for the metallurgical area, with examples. Issues found in other areas such as geology, mining, infrastructure and financial evaluations are briefly reviewed, highlighting the input and interaction required by metallurgists with these disciplines. A checklist is provided as a guide to maximise the success of a Due Diligence as well as a check on the quality of a Feasibility Study.CITATION:Newell, A J H, 2015. Fatal flaws in technical due diligences, in Proceedings MetPlant 2015, pp 61–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Steven Rupprecht

"The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code or the Code) sets out minimum standards, recommendations and guidelines for public reporting of exploration results, mineral resources and mineral reserves in South Africa. The Code is being rewritten and updated, with work on-going since 2013. The revision is being undertaken to ensure the Code remains relevant, incorporates developments within the international mining industry and keeps abreast of technology. Some of the changes and their reasons are discussed. INTRODUCTION The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code or the Code) sets out minimum standards, recommendations and guidelines for public reporting of Exploration Results, Mineral Resources and Mineral Rreserves in South Africa. The Code is being rewritten and updated, with work on-going since 2013. The proposed 2016 update is not significantly different from previous versions of the Code. The revision is being undertaken to ensure the Code remains relevant, incorporates developments within the international mining industry and keeps abreast of technology. The Code sets out minimum standards, recommendations and guidelines for public reporting. However, reporting may be unclear, ambiguous, selective, obscure, distorted or unintelligible. Part of the purpose of the update is to provide better guidelines to Competent Persons (CPs) to ensure that the material information is being reported and that reporting is transparent in accordance with the guidelines of the Code. The information provided should, as required by the Code, be adequate to inform the “reader/investor or potential investor to make a reasonable and balanced assessment of the significance of the information”. The Committee for Mineral Reserves International Reporting Standards (CRIRSCO) highlights the importance of the reporting Codes, as provided from a quote from their website (www.crirsco.com): The mining industry is a vital contributor to national and global economies. It is a truly international business that depends on the trust and confidence of investors and other stakeholders for its financial and operational well-being. Unlike many other industries, it is based on depleting mineral assets, the knowledge of which is important prior to the commencement of extraction. It is therefore essential that the industry communicates the risks associated with investment effectively and transparently in order to earn the level of trust necessary to underpin its activities."

Jan 1, 2015

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou'gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By Joshua Alyson Freitas Ribeiro

Aços com teores eutetóides, tratados termicamente são usualmente utilizados em trilhos metroviários. Para que sejam atingidas as propriedades mecânicas desejadas para as devidas aplicações, o material pode ser submetido a alguns tratamentos térmicos, como, por exemplo, Recozimento Pleno, Normalização e Têmpera. Os tratamentos térmicos são de extrema importância, pois possibilitam uma grande versatilidade na utilização dos aços em geral. Neste estudo, as peças utilizadas são provenientes de um trilho metroviário e foram fornecidas pelo Laboratório de Pesquisa e Tecnologia em Soldagem da Universidade Federal do Ceará. Foram feitas análises metalográficas após diferentes tratamentos térmicos em peças do Aço SAE 1080 Fe-C com o objetivo de verificar os aspectos microestruturais e a sua inflências no comportamento mecânico das amostras e a alteração nas propriedades mecânicas. Pelo fato do material estudado ter uma matriz com composição perlítica de, aproximadamente, 100%, são mostradas as consequências devido à mudança nos espaçamentos interlamelares provocados pela aplicação de diferentes tratamentos e a influência da fase martensita na dureza do material.

Oct 30, 2017

By E. Scheepers

The process under investigation is the large-scale production of phosphorus. Gravity delivers the feed, consisting of pelletised apatite, coke and silica (in the form of gravel), to a submerged arc furnace through ten, evenly distributed feed chutes ensuring constant packed bed volume. Within this packed bed, solid-gas reactions are dominant in generating the gaseous product. These reactions, as well as the packed bed itself, were the main focus in the development of a fully three-dimensional CFD model in which fluid flow and energy distribution are represented as functions of chemical reactions, heating and melting of material and heat losses. The associated complex process interactions necessitated the creation of two process-specific, user-developed models that integrates accurate, thermodynamical data with computational fluid dynamics calculations, as well as reaction kinetics. The boundary conditions are provided by industrial measurements, and the key model parameters of reaction kinetics were obtained by laboratory experiments for different feed mixtures. Thirteen temperature probes installed inside the refractory lining of the furnace especially for this project allowed parameter fitting and validation to be guided within the constraints of real measurements. Simulation results reveal a thin, dome-shaped, reductive zone where conditions are optimum for maximum phosphorus recovery, as well as evidence of a thermal reserve zone similar to an ironmaking blast furnace located above this reduction zone. When compared to actual operating data, the CFD model can successfully predict the specific power consumption, the phosphorus in the slag and gaseous product flowrate under given operating conditions. This CFD model forms part of a larger project that aims to create a Dynamic-CFD hybrid control model.

Jan 1, 2014

The Australian Gas Light. Company was established in 1837, the first gas being sent out from the Kent Street Works, then the headquarters, in 1841. Mortlake Works were opened in 1886, and has since grown to the vast undertaking inspected by members of the Institute.The Kent Street Works were closed in 1921. The area of the, company's property at Mortlake is 117 acres.Some interesting figures from the statistics of the company's activities for 1937 are:-

Jan 1, 1938

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By Altair Vieira de Souza

O tântalo é um dos metais mais versáteis na engenharia, podendo ser utilizado desde tecnologias espaciais até a biomedicina. Isso incentiva o estudo de novas tecnologias de obtenção do metal a partir do óxido de tântalo (Ta2O5). Neste trabalho é apresentada uma nova rota de obtenção de tântalo metálico a partir da reação magnesiotérmica do óxido de tântalo, usando como ignição o plasma de hidrogênio. Propõe-se um método alternativo ao processo Hunter, que apesar de ser o mais utilizado, é lento, pouco eficaz na produção de grandes quantidades e gera rejeitos degradantes ao meio ambiente. Foram misturados pós de magnésio (Mg) e Ta2O5 em recipiente projetado para permitir o efeito de catodo oco, e então aquecidos a plasma até a temperatura de ignição. Os experimentos foram realizados variando a pressão de trabalho buscando a redução completa do Ta2O5. Os produtos resultantes desses processos foram analisados por equipamentos de difração de raios X. Os resultados mostram que é possível a obtenção de tântalo metálico (Ta) a partir da redução metalotérmica do óxido de tântalo (Ta2O5) usando como agente redutor o magnésio e o plasma de hidrogênio como agente de ignição. A redução completa do Ta2O5 é obtida com o uso de pressões de 4,5 e 5,0 Torr.

Oct 30, 2017

By R. Curtis

To achieve compliance with 2015 EPA Tier 4 Final regulations, which permit only around 10% of Tier 3 particulate matter (PM) and NOx emissions, a number of technologies are being implemented. Use of a fuel borne nanoparticle combustion catalyst reduces the level of PM and unburned hydrocarbons exiting the combustion chamber, alleviating the burden on downstream exhaust after-treatment systems. The impact of an iron-ceria combustion catalyst (GO2) on carbon oxidation kinetics and on diesel engine emissions is presented. The iron-ceria nanoparticles catalyze carbon oxidation at lower temperatures and increase the oxidation rate by a factor of 18 at 400 °C. Engine tests on a generator powered by a John Deere Model engine and field tests on a Cummins ISC 330 tractor truck and CAT 3508B propulsion engines are presented. Use of GO2 resulted in a reduction in PM10 (particulate matter under 10 um) emissions of up to 26% and a hydrocarbon emission reduction of up to 41%. NOx emissions did not increase in these trials and the amount of change depended on engine type. Application of this fuel borne technology for emissions reductions in mining equipment offers significant benefits.

Feb 27, 2013

By Leonardo Roberto da Silva

Os fluidos de corte são empregados no processo de retificação com o intuito de lubrificar e refrigerar a peça/rebolo, além de amenizar problemas que afetam a integridade superficial da peça e também melhoram a eficiência do processo. Os fluidos de corte são muito utilizados na retificação, porém são tóxicos, dificilmente degradáveis e nocivos ao meio ambiente. Dessa maneira, é pertinente a formulação de fluidos menos agressivos. Neste trabalho, avaliou-se o desempenho de óleos vegetais como fluidos de corte em comparação com o fluido de corte integral no processo de retificação do aço ABNT 4340 temperado e revenido com dureza média de 52 HRc. O desempenho dos fluidos consistiu na análise de rugosidade, formação de espuma e odor. A caracterização dos óleos foi realizada pela viscosidade, densidade, ponto de fulgor, corrosão, índice de acidez total, índice de iodo e de refração. Os resultados mostraram que as peças retificadas com óleos vegetais apresentaram rugosidades próximas às peças usinadas com fluido integral. Na caracterização, os óleos vegetais apresentaram maior viscosidade que o integral e suas densidades foram próximas. No resfriamento, os óleos vegetais foram capazes de resfriar mais as peças que o integral, além de corroer menos. Nos outros aspectos analisados, o óleo de soja foi o que apresentou melhor desempenho. Esses resultados comprovam a eficiência dos óleos vegetais e viabilidade do uso no processo.

Aug 7, 2018

[Page Minutes 7 Discussion of L. S. Ickis' Paper 20 City Planning and Landscape Architecture for Western Coal Camps, by S. R. DeBoer 22 Discussion of Thos. Foster's Paper 26 Discussion of Safety Committee Report 30 Discussion of R. L. Hair's Paper 52 Discussion of H. I. Smith's Paper 61 Miscellaneous Discussion 62 Discussion of Thos. A. Stroup's Paper 70]

Jan 1, 1924

By Fernando Bermejo

El presente texto describe la implementación del método Flash - Flotation para el proceso de optimización de plantas concentradoras polimetálicas en la Compañía minera Raura donde se tienen diferentes gravedades especificas por cada especie mineralógica. Su aplicación comprende la fase de investigación (año 89), modificaciones (año 2002) durante la etapa de escalamiento industrial y la optimización (año 2004) de estos equipos en la empresa, los cuales no han requerido de una gran inversión. Asimismo, los beneficios de operar con la celda SK-80 y SK-240 directamente a la descarga de los molinos primarios, permite optimizar el control metalúrgico. En este sentido, la idea de separar el plomo tan pronto lo permita el sistema, es la forma correcta de optimizar la metalurgia de este en la Compañía minera Raura.

Sep 12, 2005

By Natesa I. Jayaraman

This report describes recent improvements the Bureau of Mines made in the design of its shearer-clearer water-spray system for dust control on lonwgall shearer faces. The improvements were based on findings from a field survey of six mines and laboratory test results. The report in-cludes information on installation and use of the improved shearer-clearer system and describes a field installation and 3-week underground test of the system. The improved shearer clearer, like its predecessor, reduces dust concentrations in the shearer operator's walkway by splitting the airflow on the upwind side of the shearer and confining the dust cloud to the face side of the shearer. The improved shearer-clearer system utilizes more practical-mounting locations for the water sprays and requires less water consumption. In the underground test, the improved system maintained the clean-air split in the walkway up to 40 ft downstream from the shearer. To further improve dust suppression, cooling-water manifolds were relocated into the loading zone. The laboratory and underground tests showed that the improved shearer-clearer system and the techniques described can significantly reduce the respirable dust exposure of shearer operators from shearer-generated dust.

Jan 1, 1985

By J. R. Thoenen, J. D. Warne

"INTRODUCTION Red-iron-ore deposits in northeast Alabama have been exploited at vari¬ous times for nearly 6o years. About 3-1/2 million tons of ore have been produced in the Gadsden district; but mining activity has been dormant since 1926, and furnaces within this section of the State now suffer a shortage of red ore.To alleviate these shortages, work by-the Bureau of Mines was recommended after preliminary investigations. 4/5/ Diamond drilling, to determine the lateral and vertical extent of ores of known deposits in Greasy Cove and on Shinbone Ridge, was done from August 1946 to May 1947, as Project 9-106, Alabama Red Iron Ore. Three holes were drilled in each area.ASKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of domestic mineral resources to the end that they- make the greatest possible contributions to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as possible after its conclusion. The Mining Division, Lowell B. Moon, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests."

Jun 1, 1948

By N Kado, T Iwama, R Inoue, S Ueda

Steelmaking slags are usually used as roadbed and civil engineering materials. However, the expansion phenomenon, which is caused by the volume expansion during hydration of free CaO and free MgO contained in steelmaking slag, is indispensable. Since the hydration of free MgO in steelmaking slag is much slower than that of free CaO, it is qualitatively considered that free MgO contributes to the hydration expansion of steelmaking slag over a long period of time. Similar to free CaO, free MgO consists of undissolved MgO and crystallised MgO in steelmaking slag. The latter precipitates during slag cooling. When divalent metal oxides (FeO, MnO, CaO) are dissolved in the crystallised MgO to form a MgO-based solid solution, it is expected to inhibit the hydration reaction similar to precipitated CaO. From the previous hydration test of Magnesioferrite, which was calcined after mixing MgO and Fe2O3 reagents, it was found that the higher the Fe2O3 concentration, the slower the hydration reaction progressed. In this study, by clarifying the influence of calcination conditions of MgO-FeO and MgO-FeO-MnO solid solutions, which were prepared by the calcination of mixture of MgO, FeO and MnO reagents, on their hydration reactivity, the effect of composition and thermal treatment on the formation of free MgO that is not hydrated (or easily hydrated) were discussed. To investigate the influence of MgO grain size, coarse MgO particles, which were obtained by crushing MgO crucible, were also used for heat treatment. With increasing the amount of FeO and MnO in the MgO-FeO-MnO solid solution, the hydration reaction became more suppressed. The expansion suppression effect was higher with solid-solved FeO than with solidsolved MnO. When the calcination temperature of the MgO-FeO solid solution was increased, the Fe3+/Fe2+ concentration ratio increased, resulting in a higher hydration rate.

Jun 19, 2024

By Douglas W. Reeve, Hoc Nghia Tran, David Barham

"In kraft pulp mills, the spent pulping liquor is concentrated and used as fuel in the recovery boiler. Extensive deposits are formed in the upper section of the boiler due to the very high ash content of the fuel and the volatite nature of the ash. Deposits are composed of Na2S04, Na2C03 NaCI, some potassium salts and reduced sulphur compounds. Chloride and potassium salts are enriched in the deposits compared to the smelt due to their greater volatility.Severe corrosion of the superheater tubes in a recovery boiler has been traced to three factors: a non-uniform temperature profile in the flue gas, relatively high operating steam temperatures and high chIoride and potassium concentrations in the fireside deposits.The role of chIoride and potassium in superheater corrosion has been explained by increased Iiquid phase in deposits. Together with corrosion studies, this information has shown that kraft recovery boiler superheater corrosion due to the chloride and potassium enriched deposits can be avoided by proper boiler operation and by judicious superheater and furnace design.IntroductionThis investigation of recovery boiler superheater corrosion was initiated by the discovery of severe corrosion of the final stage superheater in a Canadian closed cycle kraft pulp mill(1,2). Metal wastage leading to tube failure was believed to be due to three major causes : the relatively high operating steam temperatures, the uneven distribution of flue gas temperature across the boiler which created a "" hot spot"" and the high chloride and potassium concentrations in the superheater fire side deposit. The mill responded to the problem by i) lowering the superheater steam temperature from 475°C to 380°C, ii) minimizing the chloride content in the spent pulping liquor, by controlling the NaCI input with recovered bleach plant effluent, and iii) changing metallurgy of a portion of the bottom section of the final stage superheater platens from ferritic steel T-22 (2.25% Cr, 1% Mo) to austenitic steel Incoloy 800H (21% Cr, 32% Ni, 46% Fe, 1.5% Mn, 1% Si, 0.6% Al) (Fig. 1). Details of the superheater corrosion experienced in the closed cycle mil! have been reported in previous papers(l ·2,) ."

Jan 1, 1984