Search Documents

By Warren L. J, Horsley R. R, Meagher L

Mineral concentrators often use process water that is very saline and/or hard. In this paper the effect of increasing concentrations of sodium chloride and calcium chloride on the rheological properties of 70 wt% quartz suspensions (d5o - 10.6 ¦m) is reported. The apparent viscosity at 100 s t in 5 mol dm -3 sodium chloride solutions (approx. 300,000 ppm) was nearly 500 times the viscosity of water without salt or particles present. Part of the increase in viscosity is caused by aggregation (coagulation) of the suspension.

Jan 1, 1989

By Karla Carolina Alves da Silva

Esse trabalho tem por objetivo, propor a utilização de um dispositivo, criado na UFPE, para estudar a fadiga funcional e mecânica num atuador de Ti-Ni com memória de forma. Inicialmente, fios de Ti-Ni com efeito memória de forma, com 0,89 mm de diâmetro, foram submetidos a um tratamento térmico de homogeneização por 24 horas a temperatura de 500ºC e têmpera em água a 25ºC. Posteriormente, os mesmos foram submetidas a calorimetria diferencial de varredura para obtenção das temperaturas de transformação. De posse desses dados, foram confeccionados atuadores com a forma de mola helicoidal. Utilizando o dispositivo proposto, esses atuadores foram submetidos às deformações cíclicas, com expansão total de 10mm, num banho térmico programável, a temperatura constante de 85ºC, na condição supereslástica, essa etapa é denominada neste trabalho de ciclo rápido. Com o objetivo de analisar o efeito dessas deformações cíclicas sobre as temperaturas de transformação e a capacidade de recuperação de forma dos atuadores foi realizada um segunda etapa, aqui denominada de ciclo lento. Nessa etapa, os atuadores foram solicitados à esforços de tração equivalentes a tensão de cisalhamento no fio de 70 MPa, dentro do intervalo de temperatura entre 15°C e 85°C, e tiveram o deslocamento e as temperaturas de transformação monitorados por um sensor LVDT e por um termopar respectivamente. Os ciclos rápidos e lentos são intercalados periodicamente. Dessa forma, observou-se a influência da ciclagem termomecânica na degradação do efeito de memória de forma.

Aug 16, 2017

By Daniel Luiz Rodrigues Júnior

O presente trabalho avalia o efeito da indução máxima sobre a energia dissipada por histerese magnética em amostras de aços elétricos de grão não orientado. Tal relação foi descrita por Steinmetz como uma lei de potência cujo expoente tem valor 1,6. No entanto, esta lei falha quando aplicada a uma ampla faixa de induções magnéticas. Com o objetivo de se avaliar a aplicabilidade dessa equação chapas de aço elétrico foram caracterizadas. Ciclos de histerese foram extraídos com indução máxima variando entre 0,4 e 2,2 T com frequência 5 mHz. A área no interior dos ciclos corresponde à energia dissipada. Estes resultados mostraram uma diminuição do valor do expoente para induções entre 1,2 e 1,6 T. Este fato pode ser explicado pela estagnação do valor do campo coercivo nessa faixa de dados.

Aug 8, 2018

By Ibrahim Alp, Duygu Dinç, Ersin Yazici, Adularya Energy and Electricity Generation and Mining Inc., Oktay Celep, Haci Deveci

Thiosulfate leaching as an environmentally benign alternative to cyanide leaching has received particular attention in recent years. Most studies have focused on thiosulfate leaching of free milling ores and, to some extent, pregrobbing ores. In this study, leaching of gold from the refractory Kaletas ore (in which gold/silver alloy is the only mode of occurrence detected) in ammoniacal thiosulfate solutions was studied. A two-level full factorial design (23) was adopted to investigate the effects of concentration of thiosulfate (0.2-1 M Na2S2O3), ammonia (0.5-1 M NH3) and copper (0.05-0.1 M CuSO4) on the extraction of gold from a ground ore (-38 µm) over a period of 24 h. Statistical analysis confirmed the leaching of gold improved with increasing concentrations of thiosulfate and ammonia. In contrast, increasing the concentration of copper in the range tested adversely affected the extraction of gold. The magnitude of effects of parameters on the gold extraction was in the order of Na2S2O3 > NH3 > CuSO4. The maximum extraction of gold (69.6%) was obtained in the presence of 1 M Na2S2O3, 1 M NH3 and 0.05 M CuSO4. The negative influence of copper on gold extraction is most likely attributed to the decomposition of thiosulfate catalyzed by copper. Concentration of thiosulfate was also identified to be statistically the most important parameter for its consumption.

Jan 1, 2014

By R. G. Benson, P. R. Wotruba, K. W. Schmidt

Introduction The Fortitude deposit is located in Nevada's Battle Mountain mining district in the central Great Basin region of the Basin and Range province of the western US. The deposit is at Copper Canyon in the southernmost portion of the district, about 19 km (12 miles) southwest of Battle Mountain (Fig. 1). Mining activity in the district began in 1866 (Roberts and Arnold, 1965). Base and precious metals were mined by underground methods intermittently until 1955. Placer gold was first discovered at Copper Canyon in 1912. Moderate scale dredging of alluvial gravel at the mouth of Copper Canyon was conducted by the Natomas Co. from 1944 to 1955 (Johnson, 1973). In 1967, Duval Corp. began large scale open-pit copper mining. (Sayers, Tippett, and Fields, 1968). Copper prices decreased and precious metals prices increased in the mid-1970s so Duval's exploration efforts at Copper Canyon shifted to precious metals. These exploration efforts resulted in the discovery of the Tomboy-Minnie deposits and shortly afterward, the Northeast Extension deposit at Copper Canyon (Blake, Wotruba, and Theodore, 1984; Fig. 2). The Fortitude deposit was discovered in late 1980, after Duval had proceeded with precious metals production at Copper Canyon. Converting the existing plant facilities at Copper Canyon to a precious metals recovery system was completed in 1978 (Jackson, 1982). Production from the Tomboy-Minnie deposits began in early 1979. Precious metals production moved to the Northeast Extension deposit in 1982. In late 1984, after three years of preproduction stripping and mining of the Upper Fortitude ore zone, production from the higher grade Lower Fortitude ore zone began. Currently, Battle Mountain Gold Co. operates the Fortitude deposit. Production from the Battle Mountain mining district before 1967 included 4.6 t (150,000 oz) of gold, 65.3 t (2.1 million oz) of silver, 13.6 kt (15,000 st) of copper, 4.5 kt (5,000 st) of lead, and 13.6 kt (15,000 st) of zinc (Roberts and Arnold, 1965). At the time of Duval's 1967 start-up, ore reserves at Copper Canyon included 12.6 Mt (14 million st) in the East ore body and another 3.6 Mt (4 million st) in the West ore body. Both had average grades of 0.79% copper, 16.1 g/t (0.47 oz per st) silver and 0.86 g/t (0.025 oz per st) gold (Blake et al., 1984). The Tomboy-Minnie deposits collectively contained 3.5 Mt (3.9 million st) of ore grading 3.09 g/t (0.09 oz per st) gold and 9.6 g/t (0.28 oz per st) silver. The Northeast Extension reserves were identified as 1.4 Mt (1.5 million st) of ore with an average grade of 2.9 g/t (0.085 oz per st) gold and 5.1 g/t (0.15 oz per st) silver. Initial total reserve estimates for the Fortitude deposit were 14.5 Mt (16 million st) grading 5.14 g/t (0.15 oz per st) gold and 29.8 g/t (0.87 oz per st) silver (Jackson, 1982). Therefore, before large scale mining, the Copper Canyon area contained a minimum of 102.6 t (3.3 million oz) of gold and 541 t (17.4 million oz) of silver as mineable reserves. The Fortitude deposit reserves as of Jan. 1, 1985 were 10.6 Mt (11 million st) grading at 5.28 g/t (0.154 oz per st) gold and 28.5 g/t (0.83 oz per st) silver. Currently, the company is producing 6.8 t (220,000 oz) of gold and significant amounts of

Jan 7, 1986

By Javier Illanes, Maurice Moore, Felipe Moroni, Rafael Acosta

Any organization that subjects its activities to a continuous improvement process must be able to adequately measure the results of the implemented changes in order to pursue better results over time. This is no different for mining companies. When it comes to blasting, an accurate fragmentation analysis can correlate blast design and rock mass parameters to particle size distribution, enabling us to further analyze the correspondence of specific design patterns, applied to specific rock mass properties and the result in measured fragmentation indicators, such as P80 and fines percentage.

Sep 30, 2022

By H. O. Hofman

PAGE Part I. Decomposition OF Zinc Sulphate by Heating in Air, . 811 I. Introduction............ 811 II. Zinc Sulphate Used,..814 III. Fumes and Pyrometers,........ 816 IV. Heating Zinc Sulphate—Dehydration,...... 817 V. Heating Zine Sulphate—Decomposition...818 (a.) Beginning of Decomposition..818 (b.) Rapidity of Decomposition,..819 (c.) End of Decomposition..823 (d.) Retardations in Heating.-Curve,..825 (e.) Formation of Basic Salts,..826 Part II. Decomposition OF Zinc Sulphate by Heating with Carbon (Reducing Roast), .830 I. Introduction,........... 830 II. Experiments and Results ,.........832 III. Summay,........... 834 Part 111. Formation of Zinc Sulphate by Roasting,... 834 I. Introduction,........... 834 IT. Description of Blende,......... 836 III. Outline of Operations,.........838 IV. Details of Experiments.......... 839 1. Decrepitation,.......... 839 2. IgnitionPoint,....839 3. Sulphatizing-Roast of Joplin Blende..840 4. Sdphatizing-Roast of Warren Blemde ,..843 5. Sulphatizing-Roast with Addition of Pyrite...848 6. Summary of Sulphutizng-Roasts,....... 854 Part IV. Appendix : Formation of Zinc Ferrate...856 Part I. Decomposition of Zinc Sulphate by Heating in Air. I. Introduction. With the exception of lead sulphate. all common metallic

Jan 1, 1905

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By A L. Welsh, P S. Newling

Mill operators are entrusted to manage what are normally the largest capital assets on any mine site. Achieving maximum utilisation and lowest costs that drive operating margins are realised by applying well known fundamentals of good housekeeping and proactive (as opposed to reactive) maintenance programmes. Historically, maintenance and operations staff are bought in late during the construction stage and often do not have the time, know how or tools to put in place (let alone train the incumbent staff) a functioning maintenance system before commissioning starts. They then get drawn into a reactive maintenance paradigm as teething problems post commissioning are dealt with and day to day issues envelop the line tradesmen and supervisors. Additionally, even when some semblance of a planned maintenance system is established, it is often the case that over time personnel and cultural issues mask the development of problematic maintenance practices. As has been observed by the authors on many occasions, even when some basic programmed maintenance system is in place, the collection of maintenance data is often inaccurate, incomplete and not subject to analysis. The net result is of course a high incidence of machine failure leading to lower than expected availability, which ultimately translates to lower revenue and higher net maintenance costs. The time taken and the cost to repair a failed machine is always greater than the timely and planned repair of a worn machine.Upon review of a number of processing plants around the world, especially gold and small base metal operations, it is apparent that companies need to implement maintenance systems whereby the operators are not overwhelmed with data and can manage by exception. Inadequate or inaccurate data collection and analysis result in poor decisions being made and misguided actions taken. GR Engineering Services (GRES) has developed a system to enable the custodians of mining plant assets to make more effective and effective use of maintenance data by being able to focus on the indicators of plant deterioration and to programme concurrent maintenance activities to maximise plant availability and utilisation.This paper outlines the structures that can be employed to address the challenges of implementing a proactive asset management system. The best practice strategies described herein have been based on the fundamentals of a sound asset management framework:a phased approach to the development of Asset Management methodology and processeseffective implementation of programmed maintenance routinesmanaging asset condition data collected from various sourcesefficient analysis of asset data and management by exceptioninterfacing asset management data with Computerised Maintenance Management System (CMMS) and Electronic Management Systems (EMS) systemstips to assist with maximising asset performance.CITATION:Welsh, A L and Newling, P S, 2015. Operating strategies for custodians of company assets creating wealth, in Proceedings MetPlant 2015, pp 338–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By A. Lyndon

Vertical and lateral load tests were carried out on two 13 m deep bored cast-in-place instrumented piles, socketed into weathered sandstone. The first pile, 1200 mm in diameter, was loaded vertically to a maximum of 16000 kN and then loaded to failure under lateral load (1900 kN). The second pile, 1500 mm in diameter, was tested under lateral load up to a maximum of 2400 kN. It was found that the deflections of the 1200 mm pile were more than twice those of the 1500 mm pile under similar loads. The soils on the site are not easily tested in the laboratory, or by conventional insitu site investigation techniques, parameters needed in design can only be reliably obtained from pile test results. In this report shear moduli are back analysed from the vertical load test and the two lateral load tests. For these similarly installed piles very different design parameters were determined from the lateral load tests, the only known major difference between the piles being that the 1200 mm pile was loaded vertically before it was loaded laterally. Changes in G values needed to match performance under vertical load if applicable to lateral loading could have accounted for a significant amount of the difference.

Jan 1, 1989

By Paula Rodrigues Caumo

A tecnologia da fabricação de aços, nas últimas décadas, apresentou grandes avanços, os quais resultaram em melhorias da qualidade, principalmente no que se refere à remoção de inclusões. As inclusões podem ser responsáveis por prejudicar as propriedades mecânicas por meio da geração de trincas ou fraturas entre outros defeitos. O distribuidor do lingotamento contínuo também pode atuar na remoção destas partículas. A eficácia desta função do distribuidor demanda o conhecimento das características do escoamento do aço líquido de modo que se possa propor modificações na configuração do distribuidor. Esse conhecimento pode ser obtido mediante a utilização de modelos físicos para simular os fenômenos envolvidos. O objetivo deste trabalho é, a partir de um distribuidor com jato aberto, construído em acrílico e em escala 1:1, verificar o percentual de inclusões passantes pelo veio com ou sem a presença de bolhas. O trabalho foi executado com e sem tubo longo, sendo o tubo longo empregado para prevenir o arraste de ar para o interior do modelo. Os resultados foram obtidos por meio do ensaio de remoção de inclusões com o auxílio do ensaio de distribuição de tempos de residência. As variáveis utilizadas neste estudo são: presença bolhas e velocidade de lingotamento.

Aug 16, 2017

By D. R. Torgoson, Th. G. Sahama

"This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2siO4 and MgSiO3-FeSiO3 and gives the results of a thermodynamic attack on the problems of stability end parageneses.. Although some data are lacking satisfactory agreement with mineralogical and petrological observations is indicated.The use of thermodynamic methods in mineralogy and petrology has been rather limited, because accurate thermal data, especially for the more complicated and more important rock-forming minerals, have been too scanty to permit any systematic application to problems in those fields. It is, nevertheless, a fascinating task to investigate to what extent the mode of occurrence and the stability relations of the minerals and mineral parageneses, as revealed by petrological and mineralogical observations, agree with predictions of thermodynamics. At the present stage of development calorimetric data are needed for most of the abundant silicate minerals.Measurement of the heats of solution in hydrofluoric acid of minerals in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 affords a ready means of obtaining their heats of formation from the oxides. Combination of such data with entropy and heat-capacity values gives a means of obtaining free energies of formation from the oxides, which, in turn, are connected di¬rectly with stability and paragenoses.The two silicates of magnesium, Mg2SiO4 and MgSi03, occur as rock-forming constituents as forsterite and clinoenstatite or enstatite. The orthosilicate (forsterite) forms a series of isomorphic mixtures with ferrous-orthosilicate (fayalite). The continuity of this series, suggested by petrological observations, has boon proved experimentally by Bowon and Shairer.4/ The present work shows that those minerals constitute a series of perfect solid solutions - that is, a series of solid solutions for which heats of formation from the individual pure silicates, Mg2Si04 and Fe2SiO4, aro negligibly small.The metasilicates of magnesium and iron also form an isomorphic series. However, this series differs from the forstorito-fayalite series in the fact that the most iron-rich mixtures, between about En10Fs90 and pure Fs, appear to be unstable with respect to the paragenesis iron-rich olivine plus quartz. The supposed instability of pure FeSiO3 as a crystalline compound, at least at high and at moderate temperatures, is remarkable, as no crystal struc¬tural reason for such instability is apparent. The present work indicates, also, that these minerals form a perfect series of solid solutions and throws additional light on the instability question.In the following, the samples used in this investigation will be described. For each of the natural olivines and orthopyroxenes, with the exception of sample L, a chemical analysis was made of the purified and actually used fraction. All the analytical work was carried cut by Oleg v. Knorring, and the specific gravity determinations, by moans of a pycnomctcr, by Oiva Joensuu, both of the University of Helsinki, Finland. The determinations of the optical properties were made by Mrs. Toini Mikkola, of the Geological Survey of Finland."

Feb 1, 1949

By F. P. Haver

The Federal Bureau of Mines developed a 10,000-ampere cell to determine the economic feasibility of producing high-purity electrolytic titanium from mill scrap or offgrade sponge. Operating variables were investigated, matetial handling procedures were established, and the cost of electrorefining titanium was determined. The prototype cell produced premium-grade metal (<100 Brinell hardness number (B.h.n.)) from very impure Kroll sponge at a processing cost of less than $0.60 per pound. Refined metal was deposited at the cathode in the form of coarse (85 percent plus 34-mesh), hexagonal crystals of a titanium when the cell was operated an 850° C. A cathode current density of 1,000 amperes per square foot and a molten sodium chloride electrolyte containing approximately 5 percent by weight of soluble titanium were used. In continuous operation, at the optimum number of ampere-hours, (40,000), the current efficiency averaged slightly less than 60 percent. It was possible to supply large enough amounts of electric current for electrolysis to maintain the temperature of the bath, thus reducing overall power consumption to less than 5 kilowatt-hours per pound of metal refined.

Jan 1, 1961

By John C. Edwards

A computer program, developed for the Bureau of Mines under contract, predicts in a quasi-steady-state approximation the ventilation and contaminant concentrations and temperatures when a fire occurs in a multi-level mine. For periods of time in which there is no significant change in the ventilation, yet a fire is producing fumes, a real-time fume concentration throughout the mine is calculated. Multiple and time-variable contaminant sources can be simulated. Recirculation paths that can develop provide a mechanism for increasing the fume concentration in the mine network and are identified by the computer program. This report contains a listing of the Fortran computer program as well as the required format of the input data. Two examples are provided of the real-time spread of smoke from a fuel-rich fire throughout a multilevel mine. The first example considers an operational exhaust fan as well as a booster fan. The second example evaluates the real-time smoke spread following a failure in the exhaust fan; recirculation occurs in this latter case.

Jan 1, 1982

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By F. Ziaie

Line electrical resistivity method using physically infinite distance between current line electrodes is proposed to determine the location of mine workings. In this method at least three line electrodes are used. One of the current electrodes is used as a sinkhole electrode while the other two are used for different activiations of line electrodes when the survey area is between one of the line electrodes and outside the other one. The resistivity profiles perpendicular to the current line electrodes for different activation of electrodes is plotted versus the distance of the midpoint of the measuring potential electrodes. The anomaly due to presence of any locally lateral resistivity variation (e.g. mining cavity) will represent itself as peak or trough depending on resistivity contrast between the source of the anomaly and surrounding medium. Physical simulation of the proposed model was conducted by using a tank model in the laboratory. The results of experiments appear to be consistent with the theoretical model. Experiments for different depths and different spacial locations of the simulated cavities appeared to be successful for locating the depth and size of the cavity.

Jan 1, 1989

The use of solid state detector and radioisotope x-ray source for x-ray fluorescence analysis is illustrated by analysis for iron, copper, zinc, tin, and lead in about 700 samples taken from Australian mineral process streams. Limits of detection based on counting statistics (3 standard deviations) range from 0&#183;001 to 0&#183;004 per cent by weight element. The analysis accuracy was usualIy between 2 to 10 per cent (rms) of the mean element concentration and was determined by comparison with assays supplied by mineral companies. In most cases the main cause of error appears to be due to this assay and not the x-ray fluorescence technique.Some potential fields of application of solid state detector and radioisotope x-ray source for analyses in the mineral industry are indicated.

Jan 1, 1974