Search Documents

Flotation Circuit Optimisation - Towards More Sustainable Practice

Sep 13, 2010

By E. F. Schnitzer, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By W. P. Huleatt, Jr. Traver, Jr. Hazen

"Vanadium and uranium occur widely distributed throughout western Colorado and eastern Utah, and a few deposits have been found in northeastern Arizona and northwestern. New Mexico. The area in which it occurs includes approximately 10,000 square miles and is generally referred to as the vanadium region of Colorado and Utah.The majority of the deposits consist of replacement bodies and impregnations of rare minerals in the lower Morrison formation of Jurassic age. The ore bodies are flat, with irregular margins, and most of them conform to the stratification.The ""rim rock"" topography of the region includes many steep-walled canyons and plateaus, which afford an abundance of outcrops that have been responsible for most of the discoveries of mineralized areas. Delimitation of ore bodies within the areas is accomplished most effectively by core drilling from the surface.The deposits were discovered in 1899 and from 1911 to 1923 wore worked extensively for radioactive uranium ores, principally carnotite.The discovery and marketing of the richer and more cheaply mined pitch-blende ores of the Belgian Congo left the Colorado-Utah deposits without economic importance as sources of radium and uranium, and the region became inactive in 1923. After a period of comparative inactivity, the rising demand of the alloy-steel industry for vanadium renewed interest in the deposits, which were known to contain that metal. By 1938, vanadium production in the area had achieved respectable proportions, and new impetus was given to it by the United States’ entry into World War II in December 1941. In 1942, new treatment plants for vanadium ores were completed in Monticello, Utah, and Durango, Colo. In order to meet the requirements of these and other plants in the region, it became necessary to open new vanadium mines and prepare old onus for production.In an effort to stimulate mining, the Metals Reserve Company initiated a stock-piling program and appointed the united states Vanadium Corporation, to act as its purchasing agent.The extra production was expected to come largely from small, independent operators whose limited funds did not permit them to maintain development and exploratory programs. Study of conditions made it apparent that extensive exploration would be necessary to sustain production, and accordingly the Bureau of Mines initiated an exploratory drilling project on a cooperative basis with the Geological Survey. The principal objects of the work were to enlarge the known ore reserves of the area and, if possible, discover new ones. The results have been gratifying in both respects."

Sep 1, 1946

By D. M. Doyle, P. J. Hannon

"The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) is a subsidiary of a five-year Economic and Regional Development Agreement, signed on June 11, 1984. The objectives of the M.D.A. are to strengthen and diversify the Nova Scotian mineral industry and to coordinate federal and provincial policies and programs. The agreement outlines the activities and responsibilities of each government, including the division of the cost (60:40, federal: provincial) between governments. The agreement established a framework for joint planning to avoid overlap or duplication of programs.The M.D.A. programs are broadly divided into five sectors (Table 1 and Fig. 1): Geoscience, Minerals Technology, Development, Firm Specific and Public Information. Each sector is administered by a subcommittee composed of one federal member and one provincial member. The subcommittees report to a Management Committee. The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) Management Committee is made up of Dr. Jack Reeves from EMR and Dr. Richard Potter from the NSDME.The Geoscience subcommittee, co-chaired by Peter Giles (NSDME) and William Poole (EMR), manages the regional geologic, geochemical and geophysical studies in the province. Included in this sector are studies into mineral deposits and the basic geological relationships between mineral deposits.The Mineral Technology sector is co-chaired by the authors, Don Doyle (CANMET) and Pat Hannon (NSDME). This sector of the M.D.A. conducts studies into mineral processing, sampling, deposit byproduct commodities and project feasibility analysis."

Jan 1, 1987

By Vítor Covre Evangelista da Silva

Esta proposta objetivou desenvolver uma análise teórico/experimental da influência de 2% Ag (em peso) em uma liga de solda Sn-40%Bi solidificada unidirecionalmente em regime transitório de fluxo de calor. Correlações experimentais entre os parâmetros térmicos de solidificação como velocidade de deslocamento da isoterma liquidus - VL, taxa de resfriamento - ?L e parâmetros microestruturais como espaçamentos dendríticos secundários – l2 foram determinados. A caracterização microestrutural foi realizada por meio de microscopia ótica e eletrônica, difração de raios-x, além de fluorescência de raios-x para obtenção dos perfis de macrossegregação dos solutos (Bi, Ag). Para determinação do perfil de dureza foram realizados ensaios de dureza Vickers. As microestruturas brutas de fusão da liga Sn-40%Bi-2%Ag são compostas de dendritas ricas em Sn decoradas com partículas de Bi circundadas por uma mistura eutética (Sn+Bi) e partículas primárias de Ag3Sn. Os parâmetros térmicos decresceram com aumento da camada solidificada, permitindo uma ampla variação: ?L ? 0,1 a 10,0°C/s, VL ? 0,2 a 0,9mm/s e GL ? 0,4 a 11,0°C/mm. O teor de bismuto não variou significativamente, ao passo que a prata variou de forma efetiva, concentrando-se no início do lingote (até próximo de 35mm). O surgimento de braços dendríticos terciários em 15mm conteve a diminuição da microdureza Vickers, esperada para as posições mais afastadas da interface metal/molde.

Aug 16, 2017

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office- workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections:

Jan 1, 1963

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By G. Akdogan, P. Mutimutema, M. Tadie

The South African gold mining industry has a legacy of abundant tailings dams, which have attracted the attention of investors because of their potential as a cheaper secondary gold resource. In this we investigate study gold recovery from a refractory calcine tailings dam. Bulk mineralogy of the tailings silicates and iron oxides to be the most abundant phases. Scanning Electron Microscopy (SEM) showed gold to exist in submicrometre and micrometre sizes, as free gold, and associated with arsenic, sulphur, and silicates e.g. quartz and talc. Gold recovery by direct cyanidation was low at 17.3%. Mechanical (ultra fine grinding P80 -16μm) and chemical (alkaline, NaOH) pre-treatment and microwave roasting and microwave-assisted cyanide leaching were investigated to increase gold recoveries. Ultrafine grinding was the most effective, producing recoveries of 66.5%. NaOH pre-leaching of ultrafine milled material increased recovery to 71.5%. Alkaline pre-leaching overall increased recoveries for non-pretreated material, making this process the most preferred because it is less costly than ultrafine grinding. Microwave roasting and microwave-assisted leaching did not achieve higher recoveries than alkaline pre-treatment or fine grinding. The investigation highlights and confirms that chemical treatment with NaOH is a powerful tool for gold extraction from refractory tailings.

Oct 1, 2022

By D. Kruse

Top down constructed large diameter (up to 90 m [300 ft]) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to: analyze various failure modes, evaluate the shaft liner and internal structures? response to seismic loading, assist in segment design, and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly, and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored.

Jan 1, 2011

By Richard J. Mainiero, Michael J. Sapko, James H. Rowland III, Marcia L. Harris

All explosive materials produce a cloud of reaction products, the most toxic of which is nitrogen dioxide (NO2). In the study reported here, 4.5-kg (10-lb) charges of blasting agent confined in either thin-wall 10-cm (4-in) diameter galvanized pipe or 10-cm (4-in) schedule 80 seamless steel pipe were detonated in a closed chamber. The detonation gases were analyzed for NO2, nitric oxide (NO), ammonia (NH3), hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), nitrogen (N2), oxygen (O2), and methane (CH4). Data were evaluated to determine the kinetics of the oxidation of NO to NO2. Analysis revealed that the only mechanism for NO loss for the conditions existing in the chamber was the reaction 2NO + O2 6 2 NO2. The rate constant was 2.08 @ 10-38 cm6 molecules-2 sec-1 for the rate equation -½d [NO]/dt = K @ [NO]2 @ [O2] for NO concentrations up to 100 ppm. The rate constant is in agreement with that recommended by Baulch, Drysdale, and Horne (1973).

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

By J. D. Morgan

Demand for nonfuel minerals depends on the overall state of the economy, which steadily improved each quarter in 1984. New housing starts rose to 1.8 million units. Automakers turned out about 15% more cars (7.8 million) and 30% more trucks (3.1 million) than in 1983. Nevertheless, many domestic mineral operations experienced difficulties in 1984. This resulted from import competition greater use of newer engineered materials, emphasis on multi-unit housing and downsizing of motor vehicles. About 15% of our energy was imported. This in cluded $36 billion worth of crude oil and $22 billion in refined products This added significantly to the overall merchandise trade deficit of $12; billion. On the bright side for mining, coal production rose 14% to 810 Mt (890 mil lion st). Three-fourths o: the coal was burned to generate electricity and more than half of our electricity was derived from coal-burning plants. With the exception of a few large-bulk, low-value raw minerals, most minerals move relatively freely in world trade. The strong dollar encouraged imports and made exporting more difficult. Consequently, our nonfuel minerals trade deficit rose 60% to $19 billion, reflecting imports of $39 billion and exports of $20 billion. There were increased pressures from some major segments of the minerals industry for some form of import protection. But President Reagan said, "Our goal is a system of free and fair trade in goods, services, and capital. We will work toward this goal through both bilateral and multilateral trading agreements." The US minerals industry consists of domestic mines, concentrators, smelters, refineries, mineral manufacturing plants, and recyclers. It also includes many wholly- or partially-owned operations in many parts of the world, providing employment and income for US citizens and others as well. Compared with 1983, the value of US raw nonfuel mineral output rose 8%, to $23 billion. The $253 billion worth of goods processed from this crude mineral output was a 14% increase. Major Metals Raw steel production - a major indicator of both material use and mineral production-rose 10%, to 84 Mt (93 million st). This stimulated a 36% rise in domestic iron ore production, to 52 Mt (57 million st), about 98% pelletized. Iron ore imports rose 44%, to 14 Mt (15 million st). Despite the increase of steel production, output remained well below levels of just a few years ago. For example, 1984 production was still 23% less than in 1981. Raw steelmaking capacity remained steady at 122 Mt (135 million st). The industry continued to cite steel imports as a major reason for low domestic capacity. In December, pacts with seven leading steel exporting nations were announced. This is an effort to reduce import penetration to about 18.5% of the domestic market. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about 50% capacity. The US mined no manganese or chromium. Only a small quantity of ferronickel was produced from domestic laterite mining in Oregon. Molybdenum production, at 45 kt (49,500 st), rose threefold. Mine shipments of tungsten, another mineral tied to steel

Jan 5, 1985

By Sam S. Taylor

"INTRODUCTION This report deals with a comparatively simple application of some of the engineering principles involved in the evaluation, installation, and operation of air- or gas-injection projects and well-clean-out and repair methods to increase the producing rates of oil wells in partly depleted pools during the war. The methods suggested for developing gas-injection projects take into consideration that in general no new wells will be drilled because of wartime restrictions of equipment and manpower and that only existing wells and second-hand machinery will be used. Because air will be employed as the injection medium in secondary-recovery operations where natural gas is scarce and expensive, the disadvantages and hazards accompanying, its use are discussed. Engineering techniques recognized as best modern practice are discussed in relation to the effect of simple air-injection development of properties on postwar operations and Probable ultimate recovery of oil. The report is an introduction to where, when, why, and how an air-injection project should be installed and operated; it is not intended to be an engineering manual for technical guidance in the selection, development, and operation of simulative methods of oil recovery.The report is intended mainly for these thousands of operators in the Appalachian region owning a few wells prodding small quantities or oil daily. Many such operators are anxious to increase their production rates by simulative means and to rehabilitate their wells so that they will produce more oil to help win the war but, in general, are unfamiliar with secondary-recovery operations and cannot afford to hire technical assistance."

Sep 1, 1944

My speech this morning is not a technical one, rather I will aim to tell you about the New Zealand Aluminium Smelters Limited and how I see it fitting into the Western World aluminium scene.

Jan 1, 1983

By A. M. Hanna

This paper presents the experimental investigation on the ultimate skin friction of batter piles. The model piles were pushed in medium dense sand deposits at different inclinations up to 30 with respect to the vertical and tested under axial compression loads. The decrease in the total skin resistance with increasing pile inclination can be explained in terms of the reduction of the ave­rage mobilized angle of friction between the pile shaft and sand. The analysis, which takes into account asymmetrical earth pressure distributions around the pile shaft, showed good agreement with experimental results.

Jan 1, 2010

By M R. Stevens

An approach of geological mapping and descriptive criteria has been used to identify hydrothermal eruption breccias, named the Onemana Breccia. These in part mantle a gold bearing fossil hydrothermal system located on the eastern side of the Coromandel Peninsula, New Zealand. Whilst eruption breccias are documented from active and recent geothermal centres within the Taupo Volcanic Zone and in Northland their recognition at Onemana is the first confirmed discovery for this lithotype within ancient hydrothermal systems of the Coromandel Volcanic Zone. At Onemana the widespread occurrence of silicification, sinters, volcanic lake sediments, eruption breccias and advanced argillic alteration allows classic hot spring epithermal modelling. The geological setting, distribution, lithological characteristics, hydrothermal alteration and trace element geochemistry of the Onemana eruption breccias are described. These breccias are closely comparable with hydrothermal eruption deposits elsewhere, particularly those in active ore forming hydrothermal systems. Consideration is given specifically to the role of the Onemana Breccia in an exploration strategy for discovering epithermal gold-silver deposits.

Jan 1, 1991

By Oliver W. Marsden, John O. Marsden

This paper presents the results of a hypothetical case study that evaluates the potential transition of a large copper mining and extraction operation to 90% renewable energy. The case study considers three phases to accomplish such a transition; phase I considers installation of renewable power generation at the site to meet a portion of the current electric power needs, phase II considers conversion of diesel combustion mining equipment to electric equipment, and phase III considers implementation of renewable energy generation coupled with energy storage systems to provide approximately 90% of the total mine site energy requirements. The paper evaluates the results in the context of a range of purchased electric power unit costs ($0.065, $0.100, and $0.135/kWh) as well as various carbon tax scenarios ($0, $5.00, and $37.30/t CO2). While the case study is hypothetical and considers a range of assumptions, it clearly identifies a pathway to potentially economically viable transitions to a renewable energy platform for mining companies. This represents an approach that mining companies can use to help to meet emissions targets, as well as social responsibility and reporting requirements.

Jun 4, 2021

By Ronald L. Bruening

IBC has developed a cost effective MRT process for the selective extraction and recovery of gold, copper, and a mixture of other base metals from mine leach cyanide solutions. This is a two-stage system in which the gold is first recovered selectively as a high purity salt. The copper is then recovered separately as a sulfate salt. The other base metals are then collected as a cyano anion concentrate. Three different SuperLig® materials are used. The first stage can be used alone on gold leach solutions where copper and other base metals are not a problem. The two or three stage system is used when the base metals build up in the leach solution, resulting in increased costs. The cyanide or cyanide/cyano anion concentrate can be recycled back to the leach solution until the build-up of other salts, etc. becomes too high, or this too can be controlled with a percentage bleed stream.

Oct 1, 2003

By J. H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) amended the Federal Mine Safety and Health Act of 1977 to improve the safety of mines. The MINER Act established a Technical Study Panel (the Panel) to provide independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant materials in underground coal mining (1). Because frictional heating is a common cause of belt fires, the Panel recommended that the Mine Safety and Health Administration (MSHA) evaluate the drum friction test to determine if such a test would contribute to conveyor belt safety beyond that provided by the Belt Evaluation Laboratory Test (BELT). This paper compares the results of the drum friction test to results from the BELT and large-scale tests for six different conveyor belts. The results are used to evaluate the drum friction test as a method to determine the fire resistance of conveyor belts.

Jan 1, 2011