Search Documents

By Kenneth C. Stewart

The overall purpose of this study was to develop and evaluate, in the laboratory, instrumentation and procedures which might allow for the use of physical measurements of earmuff attenuation which would yield results equivalent to those obtained from psychophysical measures of attenuation. The ultimate goal was to evaluate techniques which might subsequently prove feasible for physical measurement of earmuff attenuation in the field. Current instruments were modified to have a response similar to differrences observed in earmuff attenuation as observed in Volume 1 of the current contract. Mining noise spectra were selected and presented to a single subject seated in a diffuse noise field. The subject wore one of the muffs evaluated in the earlier study and was also fitted with two physical sound measurement systems. A linear system measured the "outside" noise level and a linear system plus "correction" filter measured the "in-side" noise level. These measurements indicated that, under the procedures presented in this report, a laboratory method for measuring earmuff attenuation is feasible and yields results comparable to an extensive psycho-physical procedure.

Jan 1, 1980

By Dale Dean, Bill Hancock, Raul Mondragon, Carlos Aguilar, Chris Martin

"In 1942, commercial mining operations began in what is now the Lucky Friday Ag/Pb/Zn mine in Idaho’s Silver Valley. Wholly owned since 1962 by Hecla Mining Company, the mine has produced more than 145 million ounces of silver and has been a mainstay producer in Idaho’s Silver Valley for over 70 years.However, by the early 21st century, the mill had fallen, technologically, seriously behind the rest of the industry. Accordingly, starting in 2005, the current mill management team set to revitalizing the milling operation. This paper will describe how the mill was systematically evaluated and the aging infrastructure replaced with more current technology. Driven by internal mill review studies supported by QEMSCAN mineralogical balancing, the mill has in recent years been through waves of upgrading – from the installation of new mechanical and column flotation equipment to the introduction of on-stream analysis, a technology well-accepted around most of the industry but alien to this technologically conservative mining district.The experience at Lucky Friday is a testament to the need for ongoing structured mill optimisation and technology upgrading in established mining operations. This paper will describe engineering experiences associated with upgrading equipment in an operating mill, contained in a confined building. Experiences in teaching the team new ways of operating a mill, and finally the metallurgical rewards that have been reaped will be described.INTRODUCTIONMining in Idaho’s Silver ValleyIdaho’s Silver Valley is a 64-km long valley flanked by the US Northern Rocky mountains, seldom more the 3-km wide, and stretching across much of Idaho’s northern panhandle, roughly 150 km south of the Canadian border. Mining has been continuously active in the area for more than 140 years, during which time, the Silver Valley has become one of the richest silver producing districts in the world, and as of 1985 had out-produced the 500 years of production from the famed Potosi district in Bolivia. Since 1885, almost 100 deposits have been discovered and worked in the district (Chapman, 2000)."

Jan 1, 2011

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By William Gleason

"There are signs that the commodity downturn that has battered the mining industry for the past five years is beginning to ease up. As the dust begins to settle and mining companies begin to take stock of the battle, Newmont Mining Corp. will be one that is standing strong with just a few scrapes and bruises thanks in large part to the leadership of president and chief executive officer Gary Goldberg and his right hand man and chief operating officer, Chris Robison.As he closes in on retirement (for a second time) Robison, a third-generation miner from Nevada, took time to speak with Mining Engineering about a 33-year career in which, among other things, he is credited with not just helping Newmont survive the turbulent times but with steering the company to a safer, more productive and more profitable heading.“I think we did it better than anyone else,” Robison said when asked how the company fared during the past five years. “We didn’t talk about it a lot, we just put together a strategy and we delivered.”What Newmont, the world’s second-largest gold mining company by production, delivered since Robison took the position of chief operating officer in 2013 are improvements in costs, porduction, projects and safety.Operating under the mantra of “live within your means,” Robison was pulled out of retirement from Rio Tinto and into a challenging situation at Newmont. The price of gold was in a nose dive from a high of nearly $58/g ($1,800/oz) and heading to levels closer to $38.60/g ($1,200 oz).“Newmont is a big ship that can’t be turned, but has to be steered,” said Robison. “We recognized that we had to set a new course. The direction the ship was going was great for $1,600 to $1,800/oz gold but we were chasing ounces.”Like the rest of the gold mining sector before the falling gold prices, Newmont was focused on volume and was looking for gold wherever it could be found. The slogan at Newmont in 2011 was “7 million ounces a year by 2017.”When Robison came on board it was a different reality.“We had to begin focusing on value over volume as the cornerstone of Newmont going forward,” he said."

Aug 1, 2016

By M. Lahtinen, P. Latostenmaa, I. Kojo, E. Peuraniemi, M. Lindgren, S. Jyrkönen, M. Jåfs

The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. Since then Flash Smelting technology, now owned and developed by Outotec Oyj and the first plant, now owned by Boliden Harjavalta Oy, have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a popular theme during the first days of Flash Smelting, it has still been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. This paper describes the history and improvements of the Outotec® Flash Smelting process by looking into the early days of operation and how the development of the process and equipment has taken place over time as a joint effort between the technology provider and the users of the technology. INTRODUCTION In the 1940s, Outokumpu Oy refined the concentrate produced in the Outokumpu mine into metallic copper initially in Imatra, and later from 1945 to 1949 in Harjavalta, based on the most modern electrical melting process of the world at that time. After the war, Finland lost a significant part of its hydropower production, and due to the increasing use of electricity, the availability of electricity weakened, and the price rose. To maintain Outokumpu's profitability, it was forced to look for a melting solution that was not based on electricity.

Jan 1, 2019

By T Kojovic

"The index A*b, determined from the Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight tester (DWT) results, has become well-known in the mining industry as a reliable measure of ore hardness in impact or crushing, having the inferred units of t/kWh. This index evolved from a long history of comminution studies at the JKMRC, including the development of the now superseded JKTech twin-pendulum, the industry standard JK Drop Weight Tester (JKDWT) and the faster alterative JKMRC rotary breakage tester (JKRBT). A reduced version of the DWT, the semi-autogenous grinding mill comminution test (SMC test®), also provides estimates of the A*b though the testing of only one particle size at five specific energies. Experimental determination of A*b using the above devices/tests requires samples, with sufficient mass, to be sent to designated laboratories, registered to conduct such tests. This protocol is fine for bankable and commercial testing, where material characterisation data is used in conjunction with machine specific data in modelling and simulation, and power based calculations. However, for comparative testing, where results are required at the time of sampling (eg for plant troubleshooting or spot-surveys), or for rapid ranking of geometallurgical samples, these existing tests simply do not provide a timely, viable and cost-effective solution. In order to address this critical void in the realm of comparative testing, a new device has been developed, exploiting a central feature of single particle impact testing – that the A*b can be reliably estimated using one precise low energy test. This device, for which a patent is currently pending, called the HIT (Hardness Index Tester), has been precision engineered to allow users to break narrowly sized fragments at a set specific energy, in a safe and easy manner. The manufacturing materials have been chosen carefully to ensure compatibility with the intended use and portability to any site, whilst minimising cost. The device is supplied with a novel quality assurance / quality control (QA/QC) feature, to ensure that the targeted potential energy is consistently delivered. The product from the HIT breakage test can be quickly sized using a single screen to determine the mass per cent undersize, from which the A*b index is calculated directly at site – eliminating the need to send the raw data off-site for analysis. On presized fragments, a single test using 20 fragments takes less than five minutes to complete, and the results are immediately available. The HIT is currently being tested at a major mining laboratory in the US and the results to date have proved it can deliver on all fronts. This paper describes the new prototype device, which offers users a low cost in-house mechanism for estimating the A*b at any mine site, with potential applications on fragments up to 25 mm from drill core, blast chip rejects or the grinding circuit feed. It also outlines the results of field tests carried out by an objective third party mining group and compares the results with those from current industry standard tests conducted on the same material.Citation:Kojovic, T, 2016. HIT - a Portable Field Device for Rapid Testing at Site, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 9–16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J. A. Elliot

Deep Mix-in-Place soil stabilisation is achieved by forming columns of soil/cement arranged to overlap by secant intersection. Alternate columns are constructed initially and infilled. The cementitious material injected is designed to retard the strength of the resulting mix thereby allowing satisfactory overlapping. Columns are constructed using a designed large diameter mixing auger mounted on a smaller diameter auger stem. This is firstly screwed to the design depth removing only such spoil as to enable penetration of the auger, and subsequently counter rotated and extracted in a predetermined mixing pattern and grout injection rate to ensure continuous and homogeneous treatment through each successive level. The process is performed whilst monitoring auger depth, grout flow and pressure. Cementation Piling and Foundations Limited used this technique to stabilise allu­vium and to facilitate the construction, by conventional techniques, of a circular pumping station pit of 10M diameter to 10M below ground level. The work was carried out within 3M of adjacent domestic properties, and on a very restricted site in Elland, West Yorkshire. Ground conditions consist of 2M of cohesive alluvium becoming water bearing and increasingly sandy and gravelly with cobbles which overlies the mudstones at 10.0m depth. Sandstones beneath formed an aquiclude to artesian ground water with the underside of the open excavation approxi­mately 1.0M from the top of this material. Peripheral treatment into the mudstone, coupled with pressure relief wells, proved successful and final excavation depth was achieved in "the dry".

Jan 1, 1989

By Nicholas Adrian Barcza

"What affects and influences one’s perspective of the mining and metallurgical industries?One’s perspective of the industry we work in changes over time as a function of our experience as well as from the interaction we have with colleagues locally and probably even more so with those internationally. Furthermore, the ever-changing environment continues to impact the context in which one sees things. Living mostly in South Africa through its changes in the past fi fty years but also having the opportunity to travel extensively and work on projects abroad adds an invaluable richness to this more global perspective. One of the greatest challenges is how best to use this experience to endeavour to support the many potential opportunities in southern as well as sub-Saharan Africa. However, one has also to face the realities of how the best interests of the country and its peoples are sadly often not well served for various unfortunate reasons. Investment, education, regional stability, and good governance are some of the most critical considerations for the prosperity and survival of the region.The mining and metallurgical industry in southern and sub-Saharan Africa changed significantly during the post-colonial and apartheid eras as a result of global and regional developments that have impacted the ownership of businesses, the technologies used, and products produced in a manner that was not envisaged even fi fty years ago. Southern Africa’s mining and metallurgical industry has progressed from one based mostly on diamonds and gold in the late 19th century to a much more diverse one that involves the production of a variety of other precious, base, and ferrous metals and minerals as well as coal and industrial minerals. The infrastructure and manufacturing capacity was largely developed to meet the needs of this industry during its growth phases, but even though the dynamics have changed there is still a need for more efficient and effective support systems in the region."

Jul 1, 2019

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

The October General Meeting of the Institute was held in Kelvin House, Johannesburg, on 15th October, 1969, at 4.30 p.m. Mr J. K. E. Douglas (President) was in the Chair. There were also present 17 Members, Messrs: M. Barcza, R. C. J. Goode, J. A. Nixon and V. C. Robinson (Council Members), M. L. Fitzgerald, D. F. H. Graves, C. G. Hinds, S. D. Hill, J. S. Hall, D. F. Malan, T. Meyer, W. pyne-Mercier, K. S. Rae, S. G. Taussig, L. W. P. van den Bosch, Dr A. Whillier, C. H. Wyndham. Four Associate Members: Messrs O. Davel, M. J. Martinson, M. P. J. Sandys, T. G. Harington. One Student: R. P. W. Henrard. Three Visitors: Messrs A. V. Pike, B. Schmitz, A. P. Raats. Secretaries: D. C. Visser and S. de. Gersigny. Total present: Twenty-eight. OBITUARY The President: "It is my said duty to announce the death of Pieter Ulrich Fischer, Member, who joined the Institute in 1961 and passed away on 24th June, 1969. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." MINUTES The President: "The minutes of the last meeting will only appear in next month's Journal and I would request that the confirmation of these minutes be held over." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades:" Members: Alexander Edward O'Meara, Anton Leopold Melvill, WilIiam Harold Wise, Eric John Dunstan, Frank Nel, Lubertus Hendrikus Jakob Poortier. Associate Members: Michael Irvine Britten, Selwyn Wilson Lange. James McCormack, Christiaan Lodewyk de Jongh, WilIiam Andrew Hustrulid, Reinhold Johannes Ortlepp, Felix Henry Lancaster. Graduates: Willem Adriaan Gericke, Hamish David Sneddon Miller, David lan Ossin, Robert Antony Layboume, Ewart John Shillaber, Colin Hewitt Wiggett. Affiliates: Bernard Andre Thomas, Waiter Arthur Wood, Andrew John George Paschalides, David John Perry, Alex Richardson, Gert Blekker Kotze. Student: Matthys Jacobus de Beer. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: David Alphonso Viljoen. From Student to Associate Member: Michael Charles Carruthers. "I welcome the newly elected members to the Institute and congratulate the members who have been transferred to a higher grade." PAPERS FOR PRESENTATION The President: "Professor Wyndham, may I call on you to deliver the paper entitled 'Factors affecting the mechanical efficiency of men shovelling rock in stopes', written jointly with J. F. Morrison, J. H. Viljoen, N. B. Strydom and A. Heyns." After the presentation of the paper the President said: "Gentlemen, I would like to thank Dr Wyndham and his colleagues for once again reporting through the medium of this Institute the results of the very important work they are carrying out at the Human Science Laboratories. It is most appropriate that this work which is leading to a better understanding of the capabilities and efficiency of the human body under the arduous conditions encountered underground should be reported to this forum. In this way our members, who are actively engaged in the job of mining, can firstly learn something of this research and secondly, can, with their practical knowledge of conditions underground, contribute to what has been learnt and possibly pose new problems for our scientists in the laboratories. The scientist should always have the opportunity of subjecting his research to the scrutiny of people engaged in practical operations. By the very nature of our gold mines we are unfortunately heavily dependent on a large labour force and while mechanization has been introduced wherever feasible, we are likely to continue to be heavily dependent on this labour. In accepting this fact we can be proud in this country of what has been achieved, not only in obtaining the best efficiency from labour but in ensuring that their working conditions are reasonable and that their health and well-being are adequately cared for. When one visits our gold mines, one cannot help being impressed with what is being done to ensure that we have a satisfied, happy and healthy labour force. The Human Sciences Laboratory with its scientific approach has assisted greatly in promoting a better understanding of the problems associated with labour under the conditions experienced on our mines. Thank you." Mr M. Martinson then contributed to the discussion. (This contribution will appear in a later issue of the Journal.) "Professor Wyndham, may I call on you to deliver the paper entitled 'Acclimatizing men to heat in climatic rooms on mines,' written jointly with Prof Strydom." After Dr Wyndham had presented the paper the President said: "Thank you Dr Wyndham for so ably describing the work associated with the acclimatization procedures on our gold mines. It has certainly been an eye-opener to those of us not familiar with this work and I believe it is very important that everyone and not only people in the gold mines should know about it. It is fortunate that all industries do not have the same arduous heat conditions experienced on our mines but other industries such as our chemical and metallurgical industries do have other problems relating to the adjustment of labour to the work situation. The scientific approach employed by the gold mines in tackling this problem is an example to these industries of what can be achieved by logical

By Michael G. Pojar, Peter G. Chamberlain

Solution mining, primarily by heap leaching, has emerged as an important method for mining gold and silver in the United States. Heap leaching offers many economic and environmental advantages over conventional production techniques, in particular for lean ores and old mine waste rock. In order to more effectively pursue research on heap, dump, and in situ solution mining of gold and silver, the Federal Bureau of Mines conducted an extensive survey of leaching practices and problems. This presentation summarizes trends and statistics. Leaching is projected to provide 20 pct of primary mine produced gold and 10 pct of primary silver by the end of 1982. Current leaching practices in the United States are reviewed; operational problems and research programs to alleviate those problems are discussed.

Jan 1, 1981

By G. H. Sedahmed, S. A. Nosier, M. H. Abdel-Aziz, A. A. Mubarak, M. A. El-Naggar, E. G. Abdel-Aziz

The performance of a rotating fixed bed reactor in recovering copper from industrial waste solutions by cementation is studied under various conditions. The rotating fixed bed is made of stacked woven steel screens to take advantage of two features of screens: the ability to present large area per unit volume and their ability to promote high turbulence. Variables studied are initial CuSO4 concentration, bed rotation speed, mesh number of the screens and bed thickness. The presence of baffles was found to increase the rate of cementation. The data were correlated by a dimensionless mass transfer correlation suitable for the design and operation of large scale cementation reactors.

By L. L. Hirst

Liquid fuel oils possess certain advantages over solid fuels. Ease in handling, precision temperature control, and almost complete freedom from ash are among those considered when a liquid fuel is selected for use in industrial processing. In some instances these fuels are desirable because more heating units can e packed in a Given space where space is limited, as on snips. In other cases the' are chosen because of lower actual cost per British thermal unit absorbed, or for control of the flame to increase the capacity of furnaces, as in steel and refining.

Jan 1, 1948

By Sivilay Sayavong, David Puller, Julian Gatward, David Hard, Martin Stanley

"AbstractThe Thames Water Tideway Tunnels programme involves the upgrade of London’s combined sewer and storm water system. The first section is the Lee Tunnel between the Beckton Sewage Treatment Works (STW) and the Abbey Mills Pumping Station. This will intercept the overflows currently discharging to the River Lee and has the capacity to store and transfer 350,000m3 of storm water and sewage. The project required 4 shafts and a 6.9km 7.2m diameter tunnel. The shafts are some of the largest ever constructed in the UK, with diaphragm walls up to 98m deep and 1800mm thick. As a result of the innovative methods of diaphragm wall design and construction adopted the 4 very large and deep shafts were able to be excavated and completed safely, with minimal water ingress and with extremely high quality.MVB, a joint venture of Morgan Sindall, Vinci Construction Grands Projets and Bachy Soletanche are delivering the £635m contract with Thames Water’s Project Management Team in a collaborative manner under an NEC contract. Mott MacDonald, Morgan Sindall UnPS & Bachy Soletanche are acting as designers.Some of the important advances in diaphragm walling made included:??Diaphragm wall design to both EC2 & EC7 taking into considering the assessment of chalk stiffness, high hoop stresses, large multiple openings and non-axisymmetric loadings.??Formation of shafts as a faceted circle from a series of overlapping panels, with primary panels up to 7.2m wide demanding concrete volumes up to 1300m3 be poured in one go. Overlapping secondary single bite panels cut into the grade C50/60 concrete.??Excavation of the full geological stratigraphy of London making bentonite management complex.??Panel verticality of 1:300 required over the full depth. The results achieved this and in many cases exceeded expectations with some panels coming in at up to 1 in 800 with the majority at 1 in 400 to 1 in 500. The project is also the first in the Soletanche Bachy Group to take data from the ultrasonic drilling monitor used to check the verticalty in electronic format in order to create 3D CAD as-built drawings.??Each diaphragm wall panel was reinforced over its full depth. Up to 18 separate pieces of reinforcing cage had to be installed in primary panels. Cages underwent a full range of temporary works designs to check that lifting, splicing and placing could all be undertaken safely. Fibreglass was used in the tunnel portals in the shafts to ease breakthroughs."

Jan 1, 2014

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

By A. G. Galaitsis

This report summarizes the work performed under the USBM Contract No. J0245001. The purpose of this work was to expand and improve the scope and accuracy of the method developed under USBM Contract No. J0113056 for the prediction of the number of overexposed workers in the mining industry. A significant portion of the noise data were acquired during mine visits-that took place in the-course of this contract. These data were obtained with time-resolved dosimeters which among other things store a time history of the sampled noise for an eight hour work period. The remainder of the noise data have been obtained from MSHA files and from other BoM-sponsored projects. The report reviews the prediction model, discusses the model's assumptions and approximations, describes the function of the developed software, offers typical examples on the use of the software and includes plots of the newly acquired noise data records.

Jan 1, 1986

By T. G. Joseph

"The Oil sands-Equipment Interactions Program (OsEIP) is a collaborative research venture between Syncrude Canada Ltd., James Progithin International Ltd. (JPi), the University of Alberta, P&H MinePro, and Caterpillar Inc. The objective is to better understand the behaviour of oil sands as it interacts with mining equipment, in particular, large trucks and shovels. With a move to ever larger equipment, mining oil sands of highly variable bitumen content, ground stability comes into question. This paper outlines this aspect of OsEIP and provides some insight into how some of the findings enable an improved understanding of oil sands behaviour that may impact large equipment design, operational and maintenance strategies. IntroductionThe mechanical behaviour of oil sands in the underfoot and in the face yields some of the harshest stability and digging conditions of any mining environment. High maintenance costs from truck and shovel fatigue failures predominate as a result of ground stability issues. Wear rates of shovel and dozer ground engaging tools (GET), rollers, roller paths and crusher screens result in costly and frequent replacement, or even more frequent and costly sacrificial wear zone building. From the shovel face to the crushers and screens, dry oil sands mechanics affects the degree of fragmentation and, ultimately, bitumen production.An increased knowledge of the behaviour of oil sands with respect to stability, fragmentation and abrasion, etc. would enhance the long-term equipment design process at the vendor level, and provide the end user with improved short-term operational guidelines and long-term strategies for future purchases and operation. Truck vendors recognize that the interaction between operator, seat, frame, suspension, tires and oil sands is unclear, and must be better understood before proceeding to next generation designs. Similarly for shovel manufacturers, the relationship between bucket/dipper motion, carbody, side frame, rollers, track and oil sands follow in the same vein."

Jan 1, 2002

By Jerry J. Ran

In open stope mining borehole deviation is one of the main factors affecting the blasting results. Though previous research has identified some actual deviation patterns, these studies are unable to relate the hole deviation pattern with the blasting results and therefore it is not possible to modify the design or take remedial measures based on the prediction of the blasting results. An alternative to the conventional method for borehole surveying is the in-hole probing techniques. With their inherent errors, it is important to evaluate these surveying systems under conditions of different mine sites. The lack of available assessment methods has limited the application of these techniques. In this paper some of the characteristics of the actual hole deviation pattern are discussed based on data from surveying production holes in six stopes. A method of predicting the blasting results is proposed by considering the borehole deviation pattern. Based on the prediction stope design can be modified or further surveying is carried out to improve the blasting results. The tolerable error is introduced to relate the surveying error with the drilling pattern and therefore it is possible to assess various in-hole-surveying techniques.

May 1, 2002

By Péricles Guimarães Oliveira Aguiar

Este trabalho tem como objetivo desenvolver uma ferramenta de planejamento da produção de aço na Aciaria com foco na redução do ferro-gusa solidificado, através do balanço de massa integrado entre os altos-fornos e a estação de Pré-Tratamento do Gusa da Aperam South America. Os estudos mostraram que os balanços de massa elaborados apresentaram um grau de confiança satisfatório quando correlacionados aos dados industriais. O balanço de massa integrado é capaz de prever o melhor mix de produção na Aciaria em função da qualidade e do tipo de rota de refino do ferro-gusa.

Aug 17, 2017

By Kássio Nogueira Cançado

A perda de temperatura das barras de aço no intervalo entre a saída do forno e a entrada do laminador é fator determinante no processo de laminação e na qualidade do tubo produzido. O estudo feito tem como objetivo modelar matematicamente o resfriamento destas barras durante o transporte entre o forno e o laminador, permitindo avaliar a temperatura mínima necessária para desenfornamento e também o máximo tempo de transporte sem comprometer o processo de laminação, possibilitando um melhor setup dos equipamentos reduzindo os custos de produção. Os resultados obtidos com o modelo matemático de resfriamento foram comparados com valores reais de temperatura coletados através de campanhas de medições com termopares instalados em uma barra e com medições de pirômetro. Valores de temperatura foram coletados com termopares em barras de 270, 230 e 180 mm de diâmetro. As medições com pirômetros foram feitas em barras de 180 mm de diâmetro. O modelo de resfriamento apresentou para todos os casos erro relativo às medições inferiores a 3%.

Aug 17, 2017