Search Documents

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By G B. Gnoinski

The Skorpion Zinc Mine and Refinery is situated approximately 25 km north of Rosh Pinah, south-western Namibia. The supergene zinc oxide deposit at Skorpion is hosted in a volcano-sedimentary succession within the para-autochthonous Port Nolloth Zone of the Gariep Belt. Rock types hosting the ore deposit include altered and metamorphosed volcaniclastic and clastic sediments, limestone and rhyolite. At Skorpion, the metallurgical process is unique and the plant design requires minimal fluctuations within a selected feed grade. In addition, the presence of limestone inter-fingered with ore in some areas of the deposit results in dilution problems which may increase gangue acid consumption and therefore processing costs. Hence, selective mining is necessary to ensure the delivery of suitable ore to the processing plant, in order to keep the overall operating costs at a minimum. A complex control system is in place and is capable of a high degree of selectivity. The paper describes the grade control system in place at Skorpion Mine which ensures that the qualities of the blocks planned for mining and the material being mined meet the stringent process requirements of the refinery, i.e zinc grade, gangue acid consumption and deleterious elements that may impact on the efficiency and costs of the metallurgical process. Keywords: Skorpion zinc, zinc oxide, supergene, volcano-sedimentary, grade control

Jan 1, 2007

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By A. R. Kiani-Rashid

Controlled graphitization has become known as a practical method for improvement of wear resistance and machining properties in steels. In this paper, the effect of heat treatment on microstructure of CK45 steel has been investigated. Austenitising was carried out at 920°C for 5 hours. Besides, isothermal transformation was conducted at 750°C in the time range of 1-20 hours. The microstructure of the steel considerably changes by this heat treatment process which exhibits the effects of temperature, appropriate austenitising duration and isothermal transformation. Conducted experiments show a suitable distribution of semi-spherical graphite particles especially on the surface of the steel. Also, analyses demonstrate that the amount of formed graphite in the austenitising temperature 920°C is more than graphite in single heat treatment temperature of 750°C.

Jan 1, 2010

By William Lemos Bevilaqua

No presente trabalho foi avaliado, por meio de ensaios dinamométricos em um motor de combustão interna, o desempenho dos anéis de compressão em diferentes materiais de camisa de cilindro, sob alto regime de carga. Dois materiais foram utilizados nas camisas: Ferro fundido cinzento e um revestimento eletrodepositado de Níquel carbeto de silício. Os ensaios tiveram duração de quatro horas com cada configuração anéis/camisa. Parâmetros de análise, como a rugosidade média (Ra) e o aspecto superficial foram aferidos antes e após os testes. Os resultados apontam que o primeiro anel ensaiado na camisa revestida de Ni-SiC apresentou maior redução de Ra na condição estudada.

Aug 16, 2017

By Bruno Gomes Silva

O Distribuidor é um equipamento indispensável e de grande importância no processo de solidificação do aço via Lingotamento Contínuo. Os distribuidores são revestidos por um material refratário de trabalho que entrará em contato com o aço líquido. Atualmente é utilizado um revestimento que possui a necessidade de adição de água durante a aplicação, que poderá ser manual ou automática. Com o distribuidor disponível para lingotamento, o mesmo é direcionado para as máquinas de lingotamento onde serão pré-aquecidos visando retirar o excesso de umidade e promover a sinterização do refratário. O presente trabalho apresenta uma alternativa de revestimento, onde não é utilizada água na aplicação do produto, ou seja, um refratário com características de auto-endurecimento que permite iniciar o lingotamento sem haver necessidade de pré-aquecimento, o que significa partir a frio com o distribuidor.

Aug 16, 2017

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By C. S. Samis, D. P. Seraphim

In the presence of oxygen, galena is oxidized in an aqueous medium containing ammonium acetate in accordance with the following reaction: PbS + 1/2 0, + 2 NH~Ac -» PbAc, + So + 2 NH: + H2O. This reaction was studied in an autoclave under oxygen pressure by polarographic measurement of the concentration of lead ion in solution. Oxidation rate is parabolic. The reaction products are lead acetote and elemental sulfur, the latter forming a film on the galena crystal. Reaction kinetics appear to be determined by the diffusion of lead from the galena phase to the solution interface through the film of sulfur. RECENT applications of pressure leaching on a commercial scale have emphasized the metallurgical importance of the oxidation of sulfide minerals in aqueous media by oxygen under pressure. Research experience has shown that sulfates, thio-nates, and metal oxides are the products of humid oxidation of sulfide minerals in basic solutions. The metal oxides may be solubilized in the presence of a complexing ion.' Certain oxide minerals are also amenable to treatment by this type of oxidation.' Several kinetic studies have been made of reactions of this type. Stenhouse' found that pyrite (FeS?) oxidized in a sodium hydroxide solution to produce a soluble sulfate and an insoluble layer of iron oxide and that the kinetics of the reaction were controlled by oxygen diffusion through the oxide layer. Andersen' studied the oxidation of galena (PbS) in a sodium hydroxide solution under oxygen pressure. He found the lead and sulfur to be simultaneously oxidized to produce plum bite ions and sulfate ions, and that the reaction rate was proportional to the surface area of the galena. The kinetics appeared to be determined by the reaction of oxygen and water with the galena surface. In each of the above reactions the metal and sulfur components of the mineral were oxidized simultaneously and at equal rates. In the present study the alkaline medium has been replaced by an approximately neutral solution of ammonium acetate in which lead sulfate is soluble. Under the conditions no sulfate was produced and no sulfur could be detected in the solution. The metal component of the mineral was solubilized and the liberated sulfur remained as a film of elemental sulfur on the surface of the galena crystal. A kinetic study of this reaction was undertaken to establish the kinetic mechanism and to determine the rate controlling step. Specific reaction rates were determined by oxidizing crystals of galena of measured surface areas in an autoclave maintained at the desired temperature and oxygen pressure. The rate of reaction was followed by measuring the concentration of lead in the ammonium acetate solution with a cathode ray polarograph, employing stationary platinum electrodes incorporated in the autoclave. Experimental Materials and Equipment Crystals of galena obtained from Violamac Mines, Retallack, B. C., were selected for oxidation because

Jan 1, 1957

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSWA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. metallic mining workforce from March through September 1986. Similar reports have been published for the stone, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

Fire-clay blocks lining the combustion chambers of zinc concentrate flash-roasting, furnaces operating at 1,000-1,200° C. have suffered moderately rapid deterioration due to slagging. The attack is accentuated by high temperatures, and is probably caused by lead oxide volatilized from the roasted concentrate.Resistance of refractories to attack increased with increasing alumina content from 30 to 45 per. cent but at 90 per cent alumina spalling was troublesome. Magnesite bricks were'subject to some spalling, but some types may lie satisfactory. Chrome and chrome-magnesite bricks spalled seriously.Material thought to be suitable for use as a monolithic lining slagged badly and an alternative may be tested.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Ltd. uses two multi-hearth furnaces and four flash or suspension roasting furnaces for the roasting .of zinc concentrates at its Risdon Works. The hearth roasting plant has been described previously by Forster (1949).A brief descriptioI1 of the first three flash roasters was given by Gordon and Forster (1955). A fourth flash roasting furnace began operation early in 1957. This furnace is somewhat larger than the earlier furnaces, and the designed capacity is also higher, auxiliary equipment being altered to suit. An important structural difference between the older furnaces and the fourth flash roaster is that the walls of the combustion chamber of the new furnace are lined with high alumina fire-bricks instead of fire-clay blocks. Thischange was made because the fire-clay blocks in the older flash roasters had shown s-evere wastage due to slagging by lead derived from the concentrate.

Jan 1, 1959

By W. R. Green, B. W. Barde

"Geological exploration involves the collection and analysis of a wide variety of information. A basic problem in interpretation is to determine the interrelationship s of the different data. A number of statistical methods can be applied to this problem, provided that subsets of data can be selected.We have recently developed a set of interactive computer programs which provide the cap ability to quickly examine a large set of data, and may be used by people with little previous computer experience. There are two main stages in using this system. First is selection of subsets of data , by applying various tests on the values of given items. This includes matching specific entries in descriptive fields, and minimum - maximum tests on numeric fields. The second stage is basic statistical analysis and data display , including histograms, 2-D scalier plots, probability (cumulative frequency) plots, and correlation matrices. All output can be viewed on a computer terminal, and important parameters changed to produce the most effective display for use in interpretation.This system has been applied to a number of different exploration problems. An example was the determination of the nature and extent of mineralization of a gold prospect in the Queen Charlotte Islands, from drill-hole data. With the aid of the computer programs , a mineralized zone was defined, and locations for further exploration identified."

Jan 1, 1984

By Ed D. Thimons, Douglas E. Pollock, Andrew B. Cecala, Gregory J. Chekan, Jay F. Colinet, John A. Organiscak

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers’ soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat conduction/ absorption capacity of individual particles, which differs for different species of minerals. When a mixture of fine material is exposed to a radiant energy source, the various solids present in the mixture will absorb heat energy depending on their heat-conducting properties and there will be a difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with a low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler particles will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal, and quartz of 6 × 18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Jan 6, 2022

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

This study investigates the changes in seismic velocity of rockmass before and after three major seismic events to determine any potential identifiable precursory velocity changes associated with these events. Induced stress measurement is one of the challenging tasks in deep underground mining, with extreme impacts on the safety and stability of the mine. This study used p-wave passive seismic tomography to image the velocity redistribution within a rockmass, which can indicate induced stress level changes in the rockmass and detect the velocity changes that might precede a major seismic event or a rockburst. The ultimate goal of this research focus is to develop another tool for the deep-mining community that will help to increase safety and efficiency. For this purpose, the hypothesis of conventional mechanics, which implies induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs, is evaluated. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring; however, the p-wave velocity did increase in the closest “zone center” for two of the three events. 

By B E. Hall, J Poniewierski, A J. Hills

Following a review of life-of-asset work at MMG’s Rosebery mine in which a proposal to increase production from 0.8 Mt/a to 1.2 Mt/a was mooted, questions were raised as to the seemingly arbitrary reasoning for the production increase. They included: Did the proposal actually add value? Was the production rate from the mine sustainable? Was it the best identifiable value-adding configuration?A multiple scenario analysis study commenced to model how various cut-off grade values against mill throughput, along with associated capital expenditure, would impact on the potential value of the operation. This was carried out utilising the ‘hill of value’ approach promoted by AMC Consultants.The traditional approach to these studies uses a constant cut-off value (NSR – net smelter return) for the whole mine analysis. This was thought to potentially introduce a large amount of variability to the model as different ore types were thought to have different processing costs and different underground lenses were thought to have different mining costs. With the aim of developing a consistent value measure that would be comparable between the lenses, an alternative measure was suggested for all ore block values in this model, irrespective of lens location.The new measure used was a mine variable value (MVV). This allowed for the variable factors of final metal concentrate production to be removed from the ore value. From a mining point this was the haulage distance from ore source to run-of-mine (ROM). For the mill it was the amount of reagents required, varying based on grade together with the amount of power required for crushing, grinding and tailings handling.From the initial run of the model, preliminary results lead to a conclusion of increased value being gained by either increasing cut-off grade or increased mill throughput rate. The validity of the result was tested using alternative price scenarios, which although changed the absolute value achieved did not significantly change the identified value-adding strategies. The realisation of these value increases identified are however contingent on higher sustainable development rates being able to be achieved mine-wide, higher backfilling rates being able to be achieved and overcoming recognised ventilation constraints. Further detailed studies are being put in place to identify the practicality of overcoming these recognised constraints and achieving the higher-value strategies identified.The ongoing objective of the hill of value model built is to keep the model alive as a life-of-asset planning tool and to continue refining the foundation data, such that various mining strategies can be analysed with increased confidence.CITATION:Hills, A J, Hall, B E and Poniewierski, J, 2014. Mining scenario analysis and mine variable value, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008