Search Documents

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By Wagner Angelo da Silva

A crescente demanda por energia elétrica nas aeronaves modernas pode ser constatada pelo aumento da potência elétrica gerada a bordo, como exemplo o Boeing 787 produz 1000kVA, 200V trifásico, 400Hz variável contra 240kVA, 200V trifásico, 400Hz fixo produzido pelo Airbus A330, apesar de possuírem aproximadamente as mesmas dimensões. Devido à necessidade de redução de massa de transformadores, a frequência utilizada na geração de eletricidade na aeronave é de 400Hz o que acaba produzindo um aumento das perdas em núcleos de FeSi destes transformadores, principalmente pelo aumento das correntes parasitas no núcleo. Transformadores elétricos com núcleos de ligas amorfas a base de Fe vêm apresentando redução de até 70% das perdas no núcleo quando operados em 50Hz ou 60Hz. Assim, esse estudo visa discutir as vantagens e desvantagens do uso de transformadores elétricos com núcleos de ligas amorfas a base de Fe em aeronaves. Os resultados mostram que, com o desenvolvimento de novas ligas, tal utilização mostra-se viável devido a uma redução de peso de tais transformadores.

Aug 8, 2018

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By R. Knapp, R. Firlotte

"Les Terrains Auriferes (LIA) Property, formerly the Malartic Goldfield (Goldfield) mine, ceased its remaining milling operations in the fall of 1994. During the early years of mining, the mill processed a non-sulfide ore with substantial carbonate mineralization.In 1977 after an extended shutdown period, ore from a nearby property, Bousquet, was processed at the mill. That ore contained larger quantities of sulfides, and unlike the old tailings, had acid generating potential.Upon closure of the L TA mill, the closure options considered for the L TA site were to cover with:1. a thin cover of 0.5 metres of borrow material (sand and gravel) to achieve basic erosion protection/stabilization; collect acidic seepage and treat with lime.2. a 2 metres of non-acid producing tailings; final surface to be vegetated.3. an engineered oxygen barrier consisting of a multi-layer cover; final surface to be vegetated.The paper presents the technological and economical methodologies that were used to select the closure alternative, describe the associated construction challenges that were faced with the implementation of the multi-layer cover concept and presents preliminary results on the cover's performance.In addition to being the first full scale demonstration of this type of multi-layer engineered oxygen barrier cover technology, this project had the advantage of using non acid producing mine tailings as part of the reclamation solution."

Jan 1, 1997

The basic objectives of mine roadways are to provide sufficient cross sections in order to meet the needs of accommodation of equipment, transport, personnel travel and ventilation. However, many roadways become damaged to the extent of needing maintenance, generally dinting, and in some cases requiring re-ripping. The damaging of a roadway is a result of several factors including geological properties of surrounding strata, method of roadway formation, type and spacing of support and so on. Among these factors, strata conditions play an important effect on the stability of roadway. Weak rocks cause excessive roadway closures and water softens some rocks and promotes the closure problem. In this paper, a scientific discussion on the effect of water on the stability of roadways is given on the basis of results obtained by means of in-situ investigation and laboratory rock tests.

Jan 1, 1996

In his account of the Thackaringa sulphide ore, Lawrence (p. 92) reports the presence of valleriite as a minor accessory in chalcopyrite. He says that it is readily identified by its intensive anisotrophy and reflection pleochroism. He also gives (p. 87) the chemical formula as Cu8Fe4S7 Recent work by Evans et al. (1964), Chamberlain and Delabio (1965), and Schidlowski and Otteman (1966) suggests that most material identified as valleriite is, in fact, mackinawite. Mackinawite and valleriite are both extremely anisotropic and strongly reflection pleochroic, and so with fine-grained material it would be hard to distinguish them optically.Mackinawite, according to Evans et al. (p. D66) is a copper-free iron sulphide (PeS) with small quantities of nickel, whereas valleriite is considered to be a dimorph of chalcopyrite (CuPeS2 ). They found that mackinawite is much more widespread than valleriite, and, unlike the latter mineral, is commonly included in other sulphides, particularly chalcopyrite.Lawrence (p. 92) states that the valleriite inclusions are up to 0·01 mm long, so that an electron probe microanalysis should be quite feasible and provide a ready answer to this query.L. J. Lawrence: I thank Dr Townend for his comments on the occurrence of a valleriite-like mineral embedded in chalcopyrite from Thackaringa. The problem of distinguishing valleriite from mackina...

Jan 1, 1967

By Yasushi Sawada

An experimental investigation was carried out to study the rates of reduction of iron oxides dissolved in liquid Ca0-SO2-A203 slags by Fe-C droplets at temperatures ranging from 1325 OC to 1550 OC. The %FeO in the slag was varied from 5.5 to 18. Flash X-ray images were employed to observe the behavior of Fe-C droplets in the slags during the reactions and for determining the slag-gas-metal interfacial area. Effect of P205 in the slag and sulfur in the droplet was also investigated. The reduction rates were determined by measuring the volume of CO evolved as a function of time and the estimated slag-gas- metal interfacial area. The reduction rates have increased with increasing %FeO in the slag and the slag temperature. The experimentally established relationship between the reduction rates and FeO (wt%) in slag is given by

Jan 1, 1992

By Daniel W. H. Su

The importance of incorporating fundamental principles of rock material response and failure mechanics into a pillar strength design model has been demonstrated. To accurately assess pillar strength, a model should account not only for the characteristics of the coal, but also for those of the surrounding strata. The interactions between the pillar and the surrounding roof and floor dictate ultimate pillar strength. Confinement, or the lack thereof, provided by roof and floor frictional end-constraint is one of the most significant factors in the strength of very wide pillars. The best conditions for end-constraint occur with ideally strong roof and floor. In this paper, it will be shown that weak roof and floor may decrease the ultimate pillar strength by as much as 30% compared to ideal conditions. Field observations confirm this pillar strength reduction in the presence of weak roof and floor. Furthermore, rock partings within the coal have a variable effect on pillar strength, depending on the parting strength. A competent shale parting within the coal reduces the effective pillar height, thus increasing the ultimate pillar strength; a weak claystone parting slightly decreases the strength. Imposed load distribution also has a significant effect on pillar strength, such that asymmetric pillar loading, similar to that observed in pillars adjacent to high extraction mining, reduces the ultimate pillar strength below that of equivalent pillars subject to uniform load distributions.

Jan 1, 1997

Continuing with the effort of providing new and more effective exploration methods to the mining industry, where direct methods (drilling, cross-cutting, etc.) are not applicable, either for logistical or environmental reasons or because they are costly and sometimes ineffective, we present here a new seismic technique based on full wave recording of 3-D channel waves generated within the coal seam across a longwall. In the past two years we reported the application on In-Seam High Resolution Seismic Reflection (ISHRSR) and In-Seam Seismic Tomography (ISST) to map non-coal inclusions that disrupt the coal seam continuity. In the present paper we present a 3-D In-Seam Seismic Tomography (3-DTSST) method using 3-D channel waves recorded by three component high resolution geophones. The method allows to distinguish longitudinal and transversal components of the channel waves, similar to the spheroidal and toroidal modes for the free oscillations of the earth. The recording of these waves allows a more complete analysis of the free modal vibrations of channel waves, permitting a more complete inversion of the structure of the coal seam through which they travel. The full wave analysis provides additional insights of the detailed coal structure for larger, distances than for the ones previously reported using the one dimensional method. The refinement of the inversion software is also a contribution towards the better definition of the coal seam geometry and structures disturbing them such as sandstone channels, sandstone rolls, partings, mine voids, faults, fractures, etc. The method is illustrated with three case studies where subsequent mining revealed the virtues and limitations. The first example deals with the problem of mapping mine works in one side of a longwall panel which geometry is well known, to verify its applicability to map old mine works. The second example deals with a sandstone body that partially scoured the coal seam withing a longwall panel. The third shows an application of the method to map roof conditions in a longwall panel where this problem critically affected production scheduling and costs

Jan 1, 1996

By Yoginder P. Chugh

The characteristics of weak floor strata associated with actively mined coal seams in Illinois are very important from ground stability point of view and, in many cases, are the governing factors in determining the size of pillars and mine openings. Laboratory and field getotechnical characterization studies of weak floor strata were conducted at six mines during the period 1985-1988. Correlation analysis among engineering index properties, and laboratory, and field determined strength-deformation properties were conducted to identify simple tests which can be used to estimate ultimate bearing capacity and deformation properties of immediate floor strata. It was concluded that the ultimate bearing capacity (UBC) and strength- deformation properties of the weak floor strata can be estimated from simple tests such as, natural moisture content, atterberg limits, and axial swelling strain. Indirect tensile strength was found to be a better estimator of UBC than unconfined compressive strength.

Jan 1, 1989

By Youngtak Ko, Wonnyon Kim

Korean contract Mn-nodule field in the NE equatorial Pacific is composed of seven sectors showing average water depths of 4,513 - 5,025 m. Of the various factors controlling the property of Mn-nodules, water depth has a potential linkage to chemical composition, shape and abundance of nodules. To clarify such a possibility, we review more than 20 years of research data in one of the northern sectors (hereafter KR1) where there is a marked contrast in water depth. High-resolution seabed mapping clearly separates a northern part from a deeper southern part, cutting across the middle of the KR1. In terms of nodule occurrence, manganese nodules in the deeper north are comparatively larger (2-4 cm) with rough surface (t-type) and discoidal shape (D-type), while those in the south are generally small (<2 cm) with smooth surface (s-type) and irregular shape (Itype). In addition, the nodules in the north have higher metal contents including Cu, Mn and Ni. Such connections of water depths to nodule occurrence and metal contents are commonly observed in the Korea licensed Pacific nodule fields. However, the relation between nodule abundance, size and water depth may be a different story. In KR1, nodule abundance and size are probably controlled by morphological features especially in the north. Seamounts in the north continuously provide rock fragments as new nuclei for the nodules. As a result, the nodules can not grow larger than 2 cm and show the shapes of newly formed nodules (i.e., smooth surface and irregular shapes). Such an interpretation is supported by anomalously high backscattered intensities in the side-scan sonar image map of the north, which possibly reflects a younger generation of magmatic activity.

Sep 1, 2014

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

Keywords: Pyrometallurgy, Pretoria University Substantial research in pyrometallurgy at the University of Pretoria started in 1980 with the appointment of Rian Dippenaar to the Iscor Chair, a position that he held until 1996, when Chris Pistorius became the leader of this pyrometallurgy group. This paper reviews the main research themes over the quarter-century from 1980 to 2005, as well as some of the industrial developments that have shaped the research approach. The main topics have been the use of electrochemical sensors for equilibrium measurements, ilmenite smelting, steel processing, and reduction.

Jan 1, 2006

In referring to two subjects of interest to the Members of this Australasian Institute of Mining Engineers, I would at the outset desire to express our gratification that to-day we are able to welcome as now united with ourselves, those members who until recently constituted the New Zealand Institute. It is hoped that the amalgamation so amicably arranged may be productive of the best results to all concerned, incorporated as this combination has been at the moment of the fulfilment of that greater political union, the Australian Commonwealth.Since last Annual Meeting held in Brisbane, we have come under the same roof as the Chamber of Mines of Victoria, and we entertain the hope that as that Chamber and this Institute possess so many interests in common in the encouragement and advancement of mining and metallurgical progress in these colonies, that much mutual benefit will ensue. There are many directions in which each body can assist the other, and I trust that a friendly co-operation will be maintained.It is gratifying to feel that in all the colonies a distinct movement is being made to increase the facilities for education in Mining and Metallurgy but if I may refer to our colony of Victoria in particular, we have to express the profound regret that in the means of education in the higher branches, we occupy an inferior position, and it is quite certain that we will continue to do so unless the Government is prepared to subordinate provincial considerations to the weightier.

Jan 1, 1901

At the present time this plant is treating by direct cyanidation 1,000 tons of ore from Open Cut mining and dumps, and 1,200 tons of current flotation tailing obtained from the Sulphide Mill, per day.The following table shows the average analysis of the two feed products (see Table 1):Precipitation Process.-The pregnant solution obtained by the cyanidation of the above has the following general analysis:-Gold 0&#183;600 dwt. per tonTotal Cyanide 0&#183;050 %Free Cyanide 0&#183;045 %Calcium Oxide 0&#183;015 %KCNS 0&#183;060 %Na2S20S 0&#183;140 %CaS04 0&#183;200 %Cu 0&#183;050 %Zn 0&#183;004 0/0K4Fe (CN) 6 NilThis solution, after standard clarification, is precipitated by means of zinc dust and a soluble lead salt.

Jan 1, 1939

Sustainable development is at odds with reality in the minerals industry. Increasing world population and aspirations are leading to increased energy and mineral consumption. Non-renewable fossil fuels are being exploited at a much faster rate than they are being discovered. Mineral reserves are diminishing and of lower grade. Despite recycling, many of the economic reserves of the rarer metals on which technological society has come to depend are being depleted, and many of the bulk metals are being exploited at ever increasing rates. And yet, mining continues, with a long-term downtrend in commodity prices, matched by more efficient mining and processing. Will society turn to a low carbon economy before fossil fuels are depleted? Will prices come to better reflect the full cost of mineral production? Will technology save us, or is it at the root of the problem? The key drivers continue to be an ever increasing aspirational population and the law of supply and demand, rather than sustainability considerations. The paper illustrates this with examples of worldwide and Australian data.

Jan 1, 2011

By William Naville

Produtos de consumo em massa causam um grande impacto ambiental, destaca-se que as empresas podem se beneficiar com ações, como a inclusão de objetivos de redução de impacto ambiental e sustentabilidade, nas etapas de desenvolvimento, projeto e seleção de materiais sem aumento nos aspectos econômicos. Três produtos de consumo em massa foram estudados: escova de dentes, embalagem de marmita e blister de medicamentos. Por meio de estimativas e simulações, utilizando-se a ferramenta de energia incorporada do software Eco Audit ®, determinou-se o consumo de energia incorporada e as emissões de CO2 para o uso de alguns materiais em potencial. Simultaneamente, considerou-se nos requisitos funcionais e geométricos a preocupação com o meio ambiente na etapa de projeto. O resultado foi que estes produtos de consumo em massa geram um grande impacto ambiental e a seleção de materiais em conjunto com os requisitos funcionais e geométricos, tendo como objetivo adicional uma redução do impacto ambiental, gera redução do gasto de energia incorporada e consequentemente a redução nas emissões de CO2.

Oct 30, 2017

A GREAT deal of attention has lately been given to the discussion as to the education required for engineers, and especially for mining engineers. The Institute of Civil Engineers has had a committee&apos;s report on it which has come to some interesting and valuable conclusions.The Institute of Mining and Metallurgy had a few years back a very long discussion on the subject, and the subject appears to be one of perennial interest to similar societies. Two recent addresses by Prof. Kernot, as president of the Victorian Instituteof Civil Engineers, are among the most interesting and practical of the contributions to the discussion. Engineers seem to feel either that the coming generation has not the same capacity to benefit by the training that has made themselves what they are, or that such training has turned out in themselves inefficient men, and that they must consequently struggle to obtain a better one for their successors. For not only is there a desire to extend existing instruction to cover the advances of science, but there seems to be a general desire also to make a completely radical change in the methods.It is not necessary to observe that education does not mean the imparting and acquiring of information, but rather the cultivation of the faculties so that the best use can be made of them and of any information acquired. For instance, a man is not educated who has by heart his lectures and the contents of his text-books, but that man is who remembers little of the actual wording of his text-books, but is able to find anything required in them...

Jan 1, 1909