Search Documents

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Bruno Pinheiro da Silva

Controlar a distribuição de carga do Alto Forno é fundamental para o controle de processo, e através de sua otimização, dentre as mais variadas configurações operacionais, busca-se lograr da estabilidade do processo e aproveitamento do gás no interior do reator. Para tal, utiliza-se um sistema de carregamento, sendo o mais usado na atualidade o do tipo Bell Less Top com calha rotativa. Durante o carregamento do forno as partículas passam pela calha rotativa, resultando em abrasão dos elementos de desgaste que por sua vez, altera a geometria da mesma, gerando alterações na trajetória das partículas carregadas e a mudança de trajetória pode perturbar a marcha do Alto Forno. Nesse contexto, a boa condição da calha passa a ser um fator essencial para a manutenção da estabilidade operacional. O presente trabalho, aplica o método dos elementos discretos (DEM) para caracterizar os efeitos do desgaste da calha na trajetória do material descarregado, podendo assim avaliar melhor os distúrbios na estabilidade do Alto Forno, e com isso a indicar o melhor momento para troca da calha.

Oct 30, 2017

Drill cores from Section 62, New Broken Hill Consolidated Ltd., were used to study the petrology of rocks associated with the zinc lode. The distribution of the rock types in relation to the lode structure was determined. The distribution of the gahnite-bearing rocks was shown to be only partly conformable with the structure.It was concluded that large scale metasomatism was not widespread, that the rocks associated with the lode (except, perhaps, the quartz-gahnite-garnet rocks) were formed by metamorphism of sediments, and that rocks and lode were contemporaneously metamorphosed.INTRODUCTIONThis investigation was undertaken in order to study the rock types associated with the zinc lode of the Broken Hill orebody, and their relationship to the structure of the ore horizons. The work was confined almost entirely to the laboratory, and is therefore limited in its scope. It is hoped, however, that the information gained may throw some new light on the genesis of the lode.Certain inferences which are drawn from this work are at variance with the ideas of a number of earlier workers.In particular, the idea of large scale metasomatism developing many of the rocks associated with the lode, especially those containing manganese, is questioned. On the contrary, the rocks associated with the lode are more simply explained as highly metamorphosed sediments, in some cases modified by water introduced from surrounding rocks into zones of strong folding and faulting. As a corollary, a metamorphicsedimentary origin for the lode material, either as a concentrated sulphide deposit, or somewhat disseminated...

Jan 1, 1961

Owing to the increased consumption of sulphuric acid; Australian manufacturers have, from time to time, been seeking for a satisfactory source of sulphur that would make them independent of foreign supplies.Some years ago a considerable amount of acid was obtained from the roasting of Spanish pyrites. This ore, in 1913 or thereabouts, cost 16s. per ton f.o.b. Huelva, and freight to the eastern seaboard of Australia was about 20s. per ton. As the ore contained 48% to 50% of available sulphur, it was costing roughly 9d. or 10d. per unit, and, in addition, the cinder, after roasting, was a product of considerable value to smelters, containing as it did a high percentage of iron suitable for fluxing, and appreciable values in silver and gold.

Jan 1, 1925

By William C. Morel, Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publica- tion of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engin- eers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal--Today and Tomorrow. 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. 011 and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1965

By Branagan D. F

The geology of the area studied is briefly described, together with the prospecting methods used in the search for copper, lead, zinc and uranium ore bodies.Four prospects, Mt. Corella, Yanasinga, Lawlor's and Greenmount, which were diamond-drilled, are described in detail and geochemical results are discussed in relation to the mineralization found. Copper anomalies were found wherever intrusive rocks were mapped, and showed a much closer relation to geology and mineralization than did the predominantly lead and zinc anomalies.Geochemical prospecting aids in the overall mineral search programme because of its speed and economy, as it helps to pinpoint areas worthy of detailed geological examination. Geochemical anomalies are a guide to favourable zones but may not indicate the presence of ore.INTRODUCTIONDuring 1953-55 the National Lead Company of New York carried out a search for minerals in an area south and west of Cloncurry (Fig. 1) in rocks of Precambrian age. After reconnaissance mapping, a number of prospects were chosen for closer examination by detailed geological mapping and geochemical sampling, and from these prospects, five sites were selected for drilling.This paper records the salient features of the exploration programme and discusses the geology and geochemistry of four of the prospects-Mt. Corella, Yanasinga, Lawlor's and Greenmount. Practically all the prospects examined showed high zinc "anomalies" or "dispersion" trains. Greta, Mt. Corella and Lawlor's prospects showed some copper anomalies and, to a lesser extent, lead anomalies. In particular, Greenmount exhibited striking copper anomalies.

Jan 1, 1960

The Golden Ridges Mine, one of the properties of New Guinea Goldfields Limited, is situated on the right bank of Nami Creek, not far from the township of Wau, in the Territory of New Guinea.The property is somewhat unique, in that the goldbearing ore-body occurs in the form of a flat seam-like deposit lying on a volcanic breccia, and covered with a mantle of overburden of decomposed porphyry. The overburden varies in thickness up to a maximum of about 65 ft.The ratio of overburden to ore is about 3 to 1. The practice developed is to strip the overburden by hydraulicking, and to mine the exposed ore under open-cut conditions, blasting to a vertical face, and using electrically operated scraper hoists for conveying the broken ore to the mill bins.The stripping of the overburden involves the boring of well-drill holes, blasting the holes and then hydraulicking the shattered material.

Jan 1, 1934

By Musa Karakus

The sedimentary iron ores of Alsace-Lorraine, France have very high phosphorous contents that average 0.7% and are as much as 2.19% P. Ores from the Tucquegnieux and Joeuf mines have been studied by cathodoluminescence microscopy, X-ray diffraction, scanning electron microscopy, and electron microprobe analysis in order to fully characterize the mineralogy, size, shape, and distribution of the deleterious phosphate grains. The phosphorous occurs as collophane, a carbonate fluorapatite, in ten morphological forms, most abundantly as microcoprolites, but also as intraclasts, concentric layers, and cortices in ooids, phosphate replaced ooids and bioclasts, phosphatiC shells, fossil infillings and internal molds, fish teeth, phosphatiC laminae, and cements between the goethite ooids. About 95% of the phosphate grains are sufficiently large that relatively fine grinding fol'lowed by reverse flotation would be expected to be effective in significantly diminishing the phosphorous content of the concentrates.

Jan 1, 1989

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Samples of crude magnesium produced by the Mintek Thermal Magnesium Process were refined in two stages. The first stage consisted of co-melting of batches of the crude metal and MgCl2-KCl flux (cleaning), followed by stirring at 30 rpm for 30 minutes and settling of the sludge (mixture of molten salt and solid impurities) from the magnesium melt. The operating temperature was 680?730°C. Most of the contained calcium and significant proportions of iron and silicon were transferred into the sludge phase, which left a metal containing, on average, 950 ppm Si, 470 ppm Fe, and 230 ppm Ca. In the second stage, small-scale refining tests were conducted on cleaned samples from the first stage, as well as on crude magnesium. FeCl3 was used as the refining agent. These tests were carried out at 715?760°C with various amounts of the refining agent. The refined metal was suitable for the production of various magnesium alloys, particularly AZ91D.

Jan 1, 2006

By Li Keqiang

This paper discusses the pile foundation of tall buildings in Shenzhen region. For 156 constructed tall buildings exceeding 18 storeys, about 86. 5 per cent of the sum. The two main types of foundation used are the semi?machine?bored/slurry drilled cast?in?situ pile and the excavation pile (hand ?dug caisson). The engineering geologiical condition in Shenzhen was analysed. In general, the bed rock level is not too deep. It belongs to hard rock, but the geologic structure is more complex and the tectonic fissures is plenty. According to experiences of the researches, tests, designs and constructions of pile foundation, we present the basic design principle of pile foundations for tall buildings as follows; (1) pile strength control to select the pile type and to choice the cross sectional dimen­sions, must be in compliance with the strength of the pile. (2) bearing stratum strongly weathered, moderartely weathered and slightly weathered rock may be used as the bearing stratum. (3) bearing pile bored /drilled cast-in-situ pile designed as an end bearing pile. (4) friction pile precast concrete pile, prestressed concrete tubular pile and driven cast-in-situ pile designe as a friction pile. In case, pile design is in compliance with these principles, it may be safe, economical and reasonable.

Jan 1, 1991

By Claudio Olalla

This paper relates to the foundation of a steel structure located at the San Martin de la Vega (Madrid) amusement park. The structure has more than 100 supports with various loading conditions, including important horizontal and uplift forces. Additionally, the settlement tolerances are very strict. A massive gypsum formation with interbedded clay layers and random solution great voids at various levels constitute the soil. The foundation design has been conditioned large enough these difficulties (load conditions and soil problems). The piling machine used was powerful to drill through the soft rock (UCS up to 11Mpa). The integrity of each pile had to be guaranteed by continuous recording of drilling and concrete pouring parameters. In order to fulfil all those conditions, a STARSOL type-piling rig was used. More than 4500 meters of piles were performed. The diameters of the piles were 450 and 550-mm and their depths varies from 6 to 23 meters. All piles were reinforced over their full length.

Jan 1, 2002

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

The need to hoist increasing loads from great depths is leading to the more general adoption of winders of the Koepe and Blair types. The trend has introduced a number of new problems in winding ropes, more particularly in the Koepe system where regular destructive tests during the life of a rope are not possible. Consequently, the importance of introducing non-destructive tests is much greater, especially so in the case of Koepe ropes used for deep winding where there are three major destructive fatiguing influences. These are rotational effects when a vertical rope is changed end-for- end each trip, the much greater range of stress to which the rope is subjected each trip as compared with drum winding, and the destructive effect of a high coefficient of friction between wheel and rope. A plea for a lower coefficient in the interest of better rope and tread life, substantiated by analysis, is made for Koepe winders operating at depth.Co-ordination of rope testing with general hoisting problems is stressed and the active participation of the Wire Rope Committee of the Australian Mineral Industries Research Association Ltd. in the promotion ofthe project is noted.The general introduction of a rope testing programme in Australia, personnel requirements and some local basic research in the subject to cope with future demands are considered.

Jan 1, 1967

By Pat DeWilliam

The Yakobi nickel-copper deposit is located essentially at tidewater in the east-central part of Yakobi Island, about 16 1 airline km (100 airline miles) west of Juneau, and can be reached by float plane and boat from Juneau and Sitka. The fishing village of Pelican, population 400, is situated 14.5 km (9 miles) to the east. An unimproved road, approximately 4 km (2.5 miles) long, connects a dock site at Lisianski Strait with the main part of the deposit known as the Basin Area (Fig. I). Other mineral occurrences are known as the Takanis, Flapjack, and Beach Areas. Another smaller nickel-copper deposit is located about 32 km (20 miles) to the south on Western Chichagof Island and is known as the Mirror Harbor nickel-copper deposit. The original discovery of the Yakobi deposit was made by S.H.P. Vevelstad about 1920 and a 47.5-m (156-ft) long adit was driven on the southwest side of the deposit in the Basin Area. The deposit was examined by J.R. Van Fleet of Union Carbide in 1930 and by J.G. Fairchild in September 1931. Stanley and Yates of the International Nickel Co. of Canada (Inco) visited the property in August or September 1937. In 1942, the controlling interest in the deposit, covered by 124 unpatented claims, was said to be held by Vevelstad and associates

Jan 1, 1991

By Ana Carolina Ribeiro Duarte

A combinação de propriedades apresentada pelos aços perlíticos permite sua aplicação em diversos segmentos. O objetivo deste trabalho foi caracterizar a microestrutura do aço SAE 1070 deformado via trefilação para a fabricação de fiomáquina. O aço foi trefilado a seco por 12 passes com reduções médias entre 15 e 21%. A caracterização microestrutural foi realizada com o auxílio da técnica de microscopia eletrônica de varredura e microscopia de força atômica. O material teve ainda seu comportamento mecânico avaliado por meio de ensaio de dureza Vickers e ensaio de tração. O material deformado apresentou a estrutura “curling” na seção transversal, enquanto que na seção longitudinal a maioria das lamelas se encontrava alinhadas com a direção de trefilação. Os ensaios de tração e dureza revelaram um aumento considerável da dureza e resistência do material após o processo de trefilação.

Aug 16, 2017

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By Patterson J. H

An infra-red absorption study has been made of crocidolite, country rock. and associated host rocks from Wittenoom Gorge. The spectrum of the country rock is appreciably different from those of crocidolite and the magnetite-rich host rocks which are closely similar. A process to separate crocidolite-bearing ore from country rock based on infra-red emission is therefore possible in theory.

Jan 1, 1966

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969