Search Documents

By Philip J. Daynes

As part of the regeneration of the centre of Dublin, a multi-functional development is being constructed on the site of the historic Smithfield Fruit Market. The site is being developed in three phases, and includes one of the deepest basements (10m) constructed in Ireland to date. Until the recent improved economic climate, there has been little requirement for deep basements in Dublin, and this is the first to be constructed entirely within fluvio-glacial gravels and boulders. The difficult ground conditions led to the adoption of a diaphragm wall solution to ensure a watertight construction. Tie-back anchorages are utilised in the temporary case, and the wall is propped by floor slabs in the permanent case. Where required by high bedrock levels, the diaphragm wall is dowelled into limestone bedrock to ensure toe stability. The recorded lateral movement of the wall is significantly below that calculated by numerical analysis. Temporary bentonite cut-off walls were installed to divide the site into discrete sections. The basement was constructed as a tanked structure, and is subject to uplift water pressure. Passive tension minipiles provides an innovative alternative to the standard stressed anchorage solution. This paper describes:- design and construction aspects of the diaphragm wall, tie-back anchorages, and anti-flotation minipiles, together with recorded lateral wall movements,

Jan 1, 2003

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

Permian coal seams from the Tomago Coal Measures in the Northern Coalfield, New South Wales, were analysed petrographically and reflectance measurements made for each. Vitrite contents were moderate to high for most of the coals but for two they were very low.The mineral-matter contents were low to moderate by Australian standards. Different profiles of a particular seam could be correlated by petrographic methods.Standard seam profiles were drawn up and from these an idealized Tomago seam sequence was compiled. All the coals were of high-volatile bituminous rank. Their carbon contents, but not thcir reflectances, varied significantly with the quantity of vitrinite present.

Jan 1, 1968

Chalcopyrite concentrate was combusted in oxygen-nitrogen atmospheres, the composition of which ranged from 1-100 per cent oxygen. Factors studied included particle size, experimental temperature and oxygen concentration. The study was assisted by chemical and X-ray diffraction (XRD) analysis and temperature measurements of single particles. Size reduction occurring after melting was found to have a major effect on the overall reaction time. Thus time to attain ignition was largely determined by the original particle size, whereas combustion time was independent of this factor. For particles larger than 40 I'm in air the time to attain ignition predominated. The maximum temperatures measured for single particles were the result of pyrite present in the concentrate. Chalcopyrite did not attain thesame temperatures. Vaporization, either as CU(g) or CuO(g) lImited the temperature. Maximum temperatures measured for single particles of pyrite ranged from 1610°C in 14 per cent oxygen to 2360°C in 100 per cent oxygen (both at 700°C). Measured temperatures were compared with those calculated from a diffusion-based model.

Jan 1, 1983

The twenty-ninth regular meeting of the Rocky Mountain Coal Mining Institute was called to order at 11:30 o'clock a. m., Monday, May 26, 1930, President B. W. Snodgrass presiding: PRESIDENT SNODGRASS (condensed report): The meeting will please come to order. As President of your Institute, I take pleasure in welcoming you to this convention, and to those who come from outside of the city, I take pleasure in Welcoming you to the city of Denver. This is the first convention at Denver in fifteen months. I hope that the annual rather than the semi-annual meetings will prove satisfactory to all, and that no mistake has been made in that respect. We are gathered together here to discuss problems common to all of us, and I am sure that we will profit by such discussion. We have with us, outside of the membership of our organization, representatives of two other organizations, Mr. Callbreath of the American Mining Congress, and Mr. Huntress of the National Coal Association. We will be honored by having them with us, and we shall expect to hear from them during this meeting.

Jan 1, 1930

By M. L. Mellish

The year 1988 unexpectedly turned out to be a good year for the US coal industry. In fact, it was a third consecutive year of record coal production. Accord¬ing to preliminary Energy Information Administration data for 1988, domestic coal consumption went up 5%, or 41 Mt (45 million st), from 1987. Coal exports were up by a surprising 13.6 Mt (15 million st). In 1988, 22.7 Mt (25 million st) of coal were drawn from stockpiles for consumption. Even so, US coal production increased to 862 Mt (950 million st). That was up 28 Mt (31 million st) from 1987. While coal consumption, exports, and production were up, delivered prices for steam coal continued to slide during the year. Metallurgical coal prices, however, firmed up and showed a moderate increase. This reflected tight metallurgical coal markets at home and abroad. Coal consumption US coal consumption reached 800 Mt (882 million st), compared with 759 Mt (837 million st) in 1987. Increased metallurgical coal consumption was one factor. Most of the rise in coal consumption, however, was due to unexpectedly high electricity demand. Unseasonably hot summer weather al lowed added coal-fired electric generation to supplement the drought-related reduction in hydro-electric power supply. Electric utilities consumed 687 Mt (757 million st) of coal in 1988, 35.4 Mt (39 million st) more than in 1987. Coal-fired power plants remained the primary source of US electricity generation, providing 57% of the total in 1988. Coal consumption at coke plants increased 13%, to 38 Mt (42 million st), from the level consumed in 1987. This increase reflects the recent recovery in the iron and steel industry. Metallurgical coal consumption in 1988 could have been greater. But US coke plants reportedly reached their maximum practical production capacity. As a result, net US coke imports amounted to 1.45 Mt (1.6 million st). Despite increased industrial activities, steam coal consumption by industrial plants was up only slightly from the 1987 level, amounting to 69 Mt (76 million st) in 1988. Residential and commercial coal consumption remained virtually unchanged at 6.4 Mt (7 million st). Coal exports and imports US coal exports rebounded in 1988, reaching 86 Mt (95 million st). It was the highest level of annual US coal exports since 1982, when they reached 96 Mt (106 million st). An unusual set of factors led to an opening for US coal exporters in 1988: • a high level of industrial production in Japan and the European Economic Community, • supply disruptions due to labor problems at coal mines in Poland and Australia, • a drought-related reduction in hydro-electric power generation in Canada, requiring increased coal-fired generation, • China's problems in meeting its export commitments, and • a fall in the value of the US dollar. US metallurgical coal exports in 1988 amounted to 56 Mt (62 million st), 9.1 Mt (10 million st) more than the 1987 level. Europe, Japan, and Canada were the principal importers of US metallurgical coal in 1988. European countries, in particu¬lar, increased their take by one-third of US metallurgical coal. The labor problems in Poland and Australia contributed to these higher levels of imports. So did increases in pig iron production of 8% in Japan and 9% in the European Economic Community. US steam coal exports - including bituminous, anthracite, and lignite-increase to 30 Mt (33 million st). This was up from 25.4 Mt (28 million st) in 1987 Contributing to this overall rise were 1.8-Mt (2-million st) increase in shipments to Canada and a 2.7-Mt (3-million st) increase to Europe. Unaffected by the somewhat tighter world coal market, US coal imports showed a slight increase to 1.8 Mt (million st) in 1988. Colombia continue to be the leading exporter to the United States, followed by Canada and Venezuela. Venezuela's entry into the US market is a relatively recent one, having made its first significant shipment in the fourth quarter of 1987.

Jan 1, 1989

The No. 2 Ore-shaft, at Mount Isa Mines Limited, involving the use of boreholes as ropeways for the upper portion thereof, constitutes, we believe, a unique feature in hoisting installations. The boreholes were sunk from the surface to a depth of 390 ft., thus eliminating the necessity of erecting the hoist at an underground location or construction of the shaft for this distance. Fig. 1, a diagrammatic cross-section through the shaft, shows the complete installation from the surface down to the first loading station below No. 7 haulage level.During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impracticable and uneconomical to continue deepening it to serve haulage levels below the present No. 5-level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5-level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin.Referring again to Fig. 1, it is apparent that the section above No. 4-level, if opened out to full shaft size, would be inoperative and would serve no useful purpose except, possibly, as a ventilation duct. Original plans therefore did not include continuation of the shaft above No. 4-level. Excavation of a hoist room upon No. 5-level; erection of sheave wheels just below No. 4-level, and a long inclined ropeway leading from the hoist to the sheaves, were incorporated in the general layout. Work on the lower sectionof the shaft had started when the idea of locating the hoist...

Jan 1, 1939

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By D. Harrington

United States newspapers of 25 or 30 Years ago ran headlines every few weeks telling of some mine disaster. Each disaster was a first-page attraction for a day or so then was forgotten until the next sensational event, frequently another mine disaster, a few weeks later. Interspersed with the large mine disasters were the so-called ?snipping? mine accidents that caused the death of one or two mine workers. The summation of mine fatalities of all types usually exceeded 3,000 a year, and nonfatal accidents to workers in mines of the country approximated 250,000 annually. From 1906 to 1910, inclusive, there were 84 major explosion disasters (about 17 per year) in. United States coal mines. The resulting fatalities totaled 2,388 for the 5-Year period. These frightful catastrophes helped the number of fatalities in coal mines of the country to reach the enormous total of 13,288 for the 5 years, or an average of 2,658 per year.

Jan 1, 1940

By José Díaz Barrios

El proceso de la explotación minera de la veta Oroya Techo, perteneciente a la mina Casapalca, ha generado un desequilibrio del macizo rocoso, donde la energía que la roca de la caja, piso y techo (volcánicos de la formación Carlos Francisco) no pueden soportar mas allá del límite de su resistencia y deformabilidad natural, es liberada o “compensada” con el estrujamiento plástico de la veta Oroya Techo (estructura carbonatada). En ese sentido, el presente texto describe una manera de cuantificar dicha deformación a través del monitoreo de convergencias, donde se emplea un simple extensómetro de cinta manual y asímediante una análisis estadístico, seleccionar estaciones de convergencia por rangos de mediciones.

Sep 12, 2005

In this paper, we present design and implementation details of a fuzzy-behavior-based controller for an automated excavator. This robotic excavator must be equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered from bucket mounted force sensors during the excavation process. Implementation details and experimental results using the fuzzy behavior based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining excavator controller.

Jan 1, 1996

By Alonso Marchena, William Martínez, Joel Otero

En Arequipa, Moquegua y Tacna se han definido diversos arcos magmáticos. En los arcos jurásico, paleoceno y oligo-mioceno ocurren pórfidos de distintas características, los cuales presentan diferencias litogeoquímicas (LaN/YbN>20, Sr/Y>40, Eu/Eu*>1, U/Th>0.27, NbN/TaN>0.7). Estos parámetros pueden ser utilizados como guías de exploración, ya que son anomalías desde el punto de vista litogeoquímico. En caso no haya mineralización visible (depósitos ocultos), el empleo de estos trazadores en unidades ígneas (diques, cuerpos subvolcánicos e intrusivos) puede señalar la probabilidad de encontrar depósitos en profundidad.

May 22, 2019

By Rafael de Souza Rodrigues

A Samarco Mineração está entre os grandes produtores mundiais de pelotas de minérios de ferro com início de suas operações em 1977 na lavra e beneficiamento de minérios itabiríticos friáveis de médio a baixo teor de Ferro. No Quadrilátero Ferrífero a formação ferrífera bandada, devido a sua gênese, apresenta, no geral, um menor teor de Fe e uma maior compacidade com o aumento da profundidade. Com a crescente demanda mundial de minério de ferro, existe a necessidade da incorporação dos materiais de menor teor e maior dureza visando o aumento das reservas. O aproveitamento desses minérios impacta significativamente as etapas de beneficiamento, sendo o processo de moagem o mais afetado, suscitando a necessidade de desenvolver ferramentas para prever o comportamento do minério nessa etapa do processamento mineral. A partir do modelo geológico-tipológico pré-existente e da introdução dos testes de determinação do tempo de moagem (DTM) e do requerimento energético da moagem nas amostras de furos de sonda, desenvolveu-se um modelo matemático para o cálculo do requerimento energético do minério na moagem. Como resultado deste trabalho, a variável “energia” (kWh/t) foi inserida no modelo de blocos da reserva podendo ser utilizada pelo planejamento de lavra de curto prazo para adequação do minério à energia de moagem existente e pelo planejamento de longo prazo para antever a necessidade de revamp nas usinas existentes e/ou para auxiliar no dimensionamento de novas instalações de moagem.

Aug 1, 2018

By Georgene Renner

At the beginning of the 1990s, Communism fell and signaled the end of the Cold War. The world rejoiced but also watched and waited to see how those countries would restructure themselves. The 1990 SME Annual Meeting was held at the Salt Palace Center in Salt Lake City, UT. The keynote session featured Alistair Frame, chairman of RTZ; Paul Queneau, professor of metallurgy at the University of Utah; and TS Ary, director of the U.S. Bureau of Mines. The SME Board of Directors voted to hire a Manager of Public Information and Education to be the GEM Program coordinator. This person was to collect and disseminate information that could be used by individual members and Local Sections to interface with government personnel and the general public.

Jan 1, 2007

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

Effect of Matching Relationship Between Bubble Size and Particle Size on Kaolinite Flotation

Sep 13, 2010

How did you get into mining; were you from a mining town or mining family? Not at all. I grew up in northwest Kansas. I liked to hunt and fish, so I thought it would be fun to work for a company that made knives or guns. It seemed like metallurgical engineers would be something those companies could use, so I started in physical metallurgy. I got a summer job at the great Climax molybdenum mine near Leadville, CO shoveling muck onto conveyors. I was hooked. I loved everything about mining, so in the fall, I changed majors from physical metallurgy to mineral processing. For many years you actually discouraged young people from studying the mining disciplines. Could that be right? That’s true.

Jan 1, 2007

When we are beset with the economic problems the world faces today, we are always inclined to look at the shorter term future. Today I would like to take a long-term view of our industry, project historical demands for our products into the future and discuss opportunities for our members. Perhaps we could firstly look at the long-term demand trends for our metals. If I tend to use non ferrous metals as a basis for my figures it is because this data is more readily available to me. I am sure that most other products of our industry show similar trends.

Jan 1, 1992