Search Documents

Jan 1, 1961

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

By J J. Batchelor, J B. Metson

Titanium (ilmenite) concentrate was extracted from a New Zealandilmeno-magnetite deposit. Tailings from the existing processing line at the Waikato North Head ironsand concentration plant were used as a raw material feed. The titanium bearing mineral extracted was defined as intergrowths of ilmenite and hematite in the size range below 150 um. The Owen-Honda equation was used to determine the conditions forilmenite/hematite magnetic separation. Three distinct regions of magnetic field strength for the mineral separation have been defined. Theoretical estimates from this calculation have been confirmed experimentally. Ilmenite concentrate was obtained using medium field magnetic andelectrostatic separation. The final material contains 40.6 - 42 per cent TiO2 and 39.1 - 39.8 per cent Fe (total). The actual yield from extraction was about seven per cent of the Zircon, leucoxene and monazite were found as byproducts of thetitanium concentration process. Preliminary experiments have shown the viability of industrial zircon benefication.

Jan 1, 2000

By G. S. Rice, H. O. Howarth, Greenwald. H. P.

"Electricity as a means of transmitting power was introduced in coal mines of the United States about 1891 for both haulage and coal cutting, only a few years after electrical haulage was first installed on street cars. At first, the hazards of electrical ignition ere not appreciated and the general use of open lights and black blasting powder made the possibility of electrical ignition of fire damp seem small by comparison.5 The possibility of igniting coal dust directly by electric sparks or arcs had not been considered.In the nine years prior to 1900, the progress of introducing electricity underground was slow, except that it was used for lighting shaft bottoms. Electricity had to contend with the more general use of compressed air for coal-cutting machines and, in mainline haulage, with the use of mule-teams and endless and tail-rope systems. During this period, great improvements were made in electrical apparatus, in surface installations as well as in mines. By 1900, therefore, the technique of applying electricity in mines had so far developed that it rapidly drove out the use of compressed air in coal mines because of the comparative ease of its installation and the marked economic advantages of its use over that of compressed air in practically all kinds of mining machines except percussion. rock drills.At this time, however, little thought was given to the hazard of indiscriminate use of electricity causing explosions and fires, and the possibility of electricity causing direct ignition of coal dust had not been considered. On December6, 1907, however, the Monongah, West Va. mine explosion occurred. This was the greatest mine disaster this country has over had, 361 men being killed. Although: there was much diversity of opinion, as to the origin of the explosion, many well-informed engineers concluded that the cause was ignition of coal dust do to wreckage of a runaway trip in a rope haulage entrance slope. This slope also served as a ventilating and it extended from the level of the coal bed to the surface. The runaway trip tore down electric cables and stirred up a cloud of dust when it was wrecked at the bottom of the slope. The dust was probably ignited by the electric arcing that occurred when the wires were knocked down. (Another but less probable source of ignition was the open flames of miners lamps.) From the foot of the slops the explosion appeared to have travelled into the mine, spreading as it went. If this ignition of coal dust was the origin of the explosion, it occurred on pure intake air entering directly from the surface."

Oct 1, 1930

By R G. Reddy, Z Zhang

Viscosities of CaO-aluminosilicate ternary melts were estimated using a structure-based model. The model considers depolymerisation effects and related breakdown of the silicate network structure on the addition of metal oxides to the melts. The predicted values are in good agreement with the experimental values over the whole temperature and composition range.

Aug 21, 2024

By Boyd Wise

A jet pump injector was developed and successfully tested, thereby demonstrating the feasibility of a jet injector for introducing coarse coal into an operating slurry face haulage system: In Phase I a variety of injection concepts were evaluated, and the jet pump was identified as best, due to its simplicity, compactness and performance potential. In Phase IIA subscale jet pump injector tests were conducted, and a computer model of a jet pump injector was developed whose performance predictions correlated well with subscale test results. In Phase IIB various system configurations were defined for integrating a jet pump injector into a fully operational underground coarse slurry face haulage system, further highlighting the feasibility and practicality of such a system. In Phase III a full-scale mobile haulage vehicle embodying a jet pump injector and coal sizing equipment was detail designed into a practical vehicle with attractive performance characteristics. More importantly, fully operational full scale jet pump injector -and feeder/breaker subassemblies were tested and proven successful in their ability to down-size coal to 3" in all 3 dimensions and to consistantly provide slurry of 4217 weight concentration at 6.4 TPM throughput under a wide range of operating conditions including zero to maximum feed rate within 5 seconds.

Jan 1, 1985

Much attention in controlling blast vibrations has been centred on the probability of causing damage to structures in the area adjacent to where blasting is carried out. In most cases these structures are residential properties and the effect of the vibrations on the occupiers has not been studied to any great extent. This paper looks at the sources of disturbance caused by blasting and their psychological effect. A comparison of ground vibration levels for compliance is examined within the framework of structural and human response.

Jan 1, 1998

By Claude Cunningham

The primary reason for blasting is to fragment rock. In production blasting, the fragment sizes produced are known to exercise an overwhelming influence over working costs: handling costs and tonnage throughput are directly affected by secondary breaking, loading and crushing, all functions of fragmentation. In addition, particular size fractions are frequently of intense interest in terms of market or process requirements.

Jan 1, 1995

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at 'any of several stages of extraction and processing, the stage of measurement used In this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the product of auxiliary processing at or near the mines.

Jan 1, 1977

By Sadegh Firoozi

Experiments measuring the kinetics of oxidation and making visual observations of the oxidation of approximately 6 g static lead baths containing arsenic, antimony and tin were conducted in the temperature range from 500 to 600 oC. A range of repeatable behaviours were observed, notably: the formation of a coherent, solid oxide layers on pure lead and lead-tin alloys; the formation of liquid oxide droplets during the initial oxidation of lead-arsenic and lead-antimony alloys and the eventual formation of a complete oxide layer covering the entire free surface of these alloys. Thermogravimetric measurements revealed that the rate of oxygen uptake was strongly influenced by the form of oxides being generated at the melt/gas interface. Compared to the rates of oxidation of pure lead, arsenic increased the rate of oxygen uptake throughout the temperature range via the formation of liquid oxidation products. The presence of antimony resulted in a moderate increase in the rate of oxygen uptake as compared to arsenic. Tin was effective in lowering the rate of oxidation even in the presence of arsenic because the oxidation product was always a coherent layer that acted as a physical barrier to oxygen transport to the underlying alloy.

Jan 1, 2006

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By Emily Johnson, Catherine Johnson, Rachel Bauer, Paul Pitzel

Demolition projects involving explosives may incorporate cutting charges to sever columns in collaboration with kicker charges that “move” the columns out of alignment. Traditional kicker charges often involve the use of dynamite secured to the column above the cutting charge. Nitroglycerine, the main component of dynamite, causes medical problems and can be a hazard to workers on site. Dynamite can also cause fragmentation of the column and structures, resulting in potential injuries to people or leading to the possibility of cutoffs in neighboring charges. This study investigates the use of water-cased kicker charges to reduce the amount of dynamite in demolition. Water charges, traditional charges, and detonating cord charges were placed on hanging steel columns and analyzed for the fragmentation of the column and velocity of the column. A W 10 X 22 beam was hung in an underground limestone test area and allowed to swing freely acting as a severed column. Charges were attached to the bottom of the column with tape and initiated using electric detonators. Explosive charges of dynamite or detonating cord were placed in the center of a water container or directly on the column for use as the kicker charge. Tests were recorded with high-speed video and velocity was calculated using Phantom Camera Control software. Velocity and time were then used to calculate force, kinetic energy, impulse, and pressure exerted by the explosive on the column. The water charge transferred energy to the column over a larger area with no direct contact of explosive and the column. Water charges moved the column faster and with more power than traditional charges. After preliminary tests, water charges were also used as the primary kicker charges in a full-scale demolition project as a case study using 118 charges. The kicker charges successfully moved building members without creating fragmentation while using less dynamite than traditional kicker charges. Due to the success, multiple full-scale projects are being designed using water charges to show success and repeatability.

Feb 6, 2023

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the last decade. Accidents rates are improving but more slowly and yet, serious accidents and fatality rates are not: in fact, these rates of more serious incidents have plateaued or deteriorating. In more dramatic cases, organizations that had ?exemplary? safety statistics, suddenly had a catastrophic or multi-fatality event occurring. Popular books such as In Search of Excellence of Peters and Waterman or Good to Great of Jim Collins created many delusional ?secrets? or recipes, to achieve great performance and yet, most of those ?great? or ?excellent? companies have now declined in their performance, some dramatically and some have fallen from grace, like Fanny Mae, a company Jim Collins identified as a ?great? one, that had to be bailed out in the latest financial crisis. These organizations share several ?delusions? about managing a business, and often, these delusions are created by academics, consultants and authors of popular books about (safety) management. More damaging however is that safety management is defined by a set of key practices or axioms: a focus on human error, compliance to rules and regulations, creating consistency of systems and actions, reacting to accidents and incidents and on prevention of those, measuring safety with performance metrics and rewarding employees on those measurements. All of these axioms contain the seeds of destruction, and they create conditions and dynamics that precede the disaster - and ironically, they are all 'good things' we do in safety management. For example, a mere focus on safety in the business, and the measurement of it, create a culture of repression of mistakes and incidents, leading to a situation where the organization knows incrementally less and less of risks and risktaking behaviour - until the day it all coincides destructively! This paper discusses seven such safety delusions and how they impact on the views and safety management approaches. They are: ??The delusion of (risk) control, that risks can actually be identified, analyzed and mitigated. ??The delusion of compliance, that mere compliance to rules will safeguard the business ??The delusion of consistency, that standard operating procedures will ensure safe operations ??The delusion of predictability, that accidents and trends tell us everything about the risks of the future ??The delusion of human error, that people are the weakest link and that it can actually be dealt with through discipline and enforcement. ??The delusion of statistical trends, that safety is measurable with statistics ??The delusion of invulnerability, that we have achieved high levels integrity and capability to deal wit risks. Organizations that suffered catastrophes all share some or all of these delusions and this paper traces how these played a role in many disasters, ranging from the Titanic, Challenger, Piper Alpha, Bhopal, BP Deepwater Horizon and many more.

Aug 1, 2013

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By R. Falcon, P. den Hoed, A. Luckos, R. Erasmus, V. du Cann, D. Comins

Carbon as a reductant, additive or filler is an essential element in the processing of metallic ores and the manufacture of iron and steel in the metallurgical industry. In most cases, the element carbon is derived from coal and its carbon derivatives. The properties of carbon required for the different processes in each metallurgical sector vary significantly and, for this reason, matching the correct carbon product for each specific process has become an important if not vital function in all sectors of this industry. This selection process, however, has become increasingly difficult. In many cases, the substitution of new products, despite being similar in all relevant chemical specification characteristics to previous products, has resulted in different performance properties relative to that expected. Under these circumstances, the prediction of performance of unknown carbon products has become fraught with difficulties unprecedented in the past. In order to initiate an investigation into addressing these issues, a test case was selected for indepth study the results of which are reported in this paper. The case concerned the use of a specific carbon feed in a conventional submerged arc furnace which gave rise to an unprecedented amount of unreacted or only partially consumed residue trapped in the frozen slag on the refractory walls of the furnace. During the course of these investigations, different advanced analytical technologies were employed including, inter alia, Raman spectroscopy, surface dimensional tests, organic petrology and various thermal reactivity factors. All results have been integrated into a multidisciplinary assessment presented in summary in this paper. Based on the above, and previous experience, the concept of an all-embracing 3-D coal-carbon ?framework? is briefly introduced. This approach has succeeded in obtaining greater depth of knowledge and a better understanding of the issues at stake with specific reference to the organic composition, structure, texture, internal surface area and consequent reactivity of the carbon materials concerned. In consequence, it would now appear that various properties of relevance to the metallurgical industry may be predicted with greater precision than has hitherto fore been possible.

Jan 1, 2004

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962