Search Documents

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962

By William P. Shinn

IT seems proper to present in the Transactions of the Institute, from time to time, formal record of the advances made in the arts and sciences to which our organization is devoted-milestones in the highway of progress-from which our successors may measure what they in their turn have gained. The admirable address of the Hon. Abram S. Hewitt, then president elect of the Institute, on "A Century of Mining and Metallurgy in the United States," read at the opening of the meeting held in this hall in June, 1876, forms a point of departure, and the conclusion of the eighth decade of the nineteenth century and the end of the first five years of our country's second century seem to offer a fitting time for again making up our record. The period since 1875 has been marked by a degree of activity in mining and metallurgical industry never before equalled in our history, while the progress made in the science and art has been, if possible, still more noticeable. Whether we consider the mining of iron, ore, and coal, or of the precious metals,-the advances made in smelting the former and in reducing the latter, the extraordinary increase in the production of Bessemer steel, or the science of Thomas and. Gilchrist, which makes the hitherto rejected phosphorus the corner-stone of success,-the past five years are alike memorable for the progress they have shown and to some of the most marked features of this progress I will now oriefly call your attention. It may be of interest in this connection to note the following figures, showing the growth of the population of the United-States during the last three decades :

Jan 1, 1881

By A. Bamber

Canadian leadership in a global mining context will depend not only on entrepreneurship and best practice but also on technological innovation. This paper argues for more ambition and commitment to R&D for technological innovation in Canadian mining. It focuses on underground hardrock mining, where past R&D initiatives have simply not stood the test of time, and it is important to examine why. Concerns arise because industry’s commitment to R&D has not been sustained over time. Innovation through exploration, processing, and environmental technologies has been more significant. Meanwhile, R&D capacity and synergies in government institutions and universities have not been exploited. There is a need for more commitment, coordination, and collaboration by industry, governments, and universities. This paper examines some corporate models that have achieved sustainable innovation, along with some that have not. A strategy for innovation is discussed that relates to culture, commitment, coordination, and collaboration.

Jan 1, 2005

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Marcos Valdéz Córdova

El presente estudio señala el proceso de mineralización en el domo de Yauli a través de una revisión en el comportamiento de dominios estratigráficos, estructurales, intrusivos, metamórficos y distintos minerales de alteración hidrotermal. Asimismo se describe la geología, su estructura, la alteración de los intrusivos, la alteración de los silicatos metamórficos, la alteración de los mármoles y calizas dolimíticas, cuerpos, mantos y las vetas de reemplazamiento.

Nov 20, 1978

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By Hillary W. St. Clair

Mining activity began in colonial times with ironmaking operations scattered along the eastern seaboard. Iron furnaces and forges manufactured iron implements from bog iron ores using charcoal from the extensive forests as a fuel. Lead ores were mined in the Mississippi Valley and copper ores in the Lake Superior region. However, the real beginning of the American mining industry did not occur until the 19th century. The history of American mining is organized around three epochal events. The first was the discovery of gold in California in 1848, which marked the beginning of a period of apprenticeship in mining and metallurgical techniques. The second was the discovery of the fabulous Comstock Lode in western Nevada in 1859, which expanded mining throughout the Far West and led to large-scale underground mining and the development of smelting techniques for lead, silver, and copper ores. The third event was the building of a transcontinental rail-road system after the Civil War, which brought about the consolidation of the industry from a large number of independent mines, mills, and smelters into integrated operations run by large corporations. Thus developed the mining industry that today supplies the energy and critical materials for the great-est industrial complex the world has known.

Jan 1, 1977

By Paul C. Schmall, Lucian P. Spiteri, Arthur B. Corwin

Moving groundwater is generally recognized as the most adversarial condition for ground freezing. Moving groundwater can occur due to natural or man-induced groundwater flow, but either way may result in freeze formation difficulties. History has shown that if the condition goes undetected, catastrophic failure of the frozen shaft or excavation can occur. The success of ground freezing under potentially flowing groundwater conditions depends on an evaluation of the likelihood for this condition; an accurate and early diagnosis, with a careful evaluation of freeze pipe temperatures and piezometer water levels; and timely reaction to mitigate the possible delays. Successful remedial measures have included the reduction of ground permeability by modifying the soil properties between the freeze pipes with various kinds of grouting, or increasing the freezing effect by adding freeze pipes and/or the use of liquid nitrogen as the freezing agent.

Jan 1, 2007

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN

Pressure losses in mine ventilation systems are estimated using friction factors and shock loss factors. The efficient planning and designing ofmine ventilation systems depend on the accuracy of the friction factors as well as the shock loss factors that are taken into consideration. While there is a much more acceptable knowledge of what constitutes friction loss in mine roadways, the shock loss factors are in general readily not available for all possible contexts of flow separation phenomena in mines. One such special case of shock loss in mines is the train of mine cars in the airway. Mine cars are widely used for the transportation of material, and the information on shock loss factor for mine cars is limited. This paper examines the pressure loss occurring due to a train of mine cars in an airway using scale model studies and numerical investigations. Computational fluid dynamic (CFD) studies are conducted using four different turbulence models. The performance of different turbulence models is analyzed by comparing it with the experimental results. The study suggests that the boundary layer resolution method is significant in the simulation of shock loss. From the study, it is found that the shock loss factors from presently available model overestimate the pressure loss by 7 to 15 times. A better prediction model for the shock loss factor of a train of mine cars in the airway is proposed using the experimental results.

Jul 24, 2020

Essential features of the role of the fill material in mechanized cut and fill mining are discussed, with particular emphasis on its dewatering and strength development after emplacement. The fill material is regarded as a chemically-reactive porous medium, the most important property of which is permeability. Methods are described for measurement of permeability and other fill properties and results of such measurements applied to develop an orderly approach to the operation.

Jan 1, 1966

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type, and causes of accidents in Turkish coal-extracting industries using Analytic Hierarchy Process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type, and causes of accidents. For this purpose, 1st, 2nd, and 3rd level hazards consisting of location, type, and causes of accident were determined by using the data of fatal mine accidents in underground and open-pit coal mining in Turkey between the years of 2010 and 2020. And then the data were categorized, and each category was prioritized using the AHP technique. According to the weights calculated by AHP, the most dangerous main criteria at 1st level hazards in underground coal mining is ventilation operations (0.363), while the most dangerous sub-criterion at 2nd level hazards is firedamp explosions and other gas accidents (0.409). On the other hand, in open-pit coal mining, the most dangerous main criteria at 1st level hazards are slopes and benches (0.575), while the most dangerous sub-criterion at 2nd level hazards are landslides (0.429).

Dec 30, 2023

By J. W. Germundson

La Cerro de Pasco Corporation fue una de las primeras compañías mineras que utilizó el explosivo a base del nitrato de amonio en las operaciones de explotación de subsuelo. En este sentido, el objetivo del texto radica en el fomento de su uso para futuras subterráneas a través del conocimiento de la historia de los explosivos, los procesos y composición del nitrato de amonio, el empleo del explosivo AN-FO Mina Cerro de Pasco en el subsuelo, usos actuales de la AN-FO, análisis de costos y las reglas de seguridad.

Aug 20, 1963

By H. Walqui, C. Noriega

Southern Copper Corporation (SCC) is one of the world’s largest copper companies and is finishing the modernization of the Ilo copper smelter. A single ISASMELTTM furnace will start smelting 1,200,000 tons per year of concentrate at the end of 2006. Three existing Peirce Smith converters are being upgraded plus a new one for converting the matte to blister copper is being installed. Two new anode furnaces and a twin anode casting wheel have being operating since January 2006. This represents one of the main changes in the process because the final product of the smelter is now anode copper instead of blister copper. A new oxygen plant, acid plant, and others facilities are in the ramp-up stage. This environmental project will ensure that the new smelter will comply with the environmental regulations of Peru by the end of January 2007. This paper summarizes the background to the modernization project, describes the different stages of the project including engineering, procurement and construction, describes the main areas of the new copper smelter and also the pre-operational testing, commissioning and start-up of them. This is a brown field project with a target of reducing as much as possible the production losses of the existing operation. This paper presents the details of the development of the Ilo Smelter Modernization Project and explains the main aspects of the new facilities, the products to be obtained and the associated facilities for their commercialization, including a Marine Trestle for bulk acid exportation.

Jan 1, 2007

By Isobel Yeo, Luca Cocchi, Sven Petersen, Nico Augustin, Sean Plunkett, Ingo Klaucke

Exploration for seafloor massive sulfides is currently mainly focused on investigation for active hydrothermal vent fields. However, most of the resource potential is thought to be related to inactive, large deposits that had enough time to accumulate sufficient tonnage. At the same time, ageing of these deposits will ultimately result also in burial acted by either sediments and/or volcanic deposits. We currently lack the technologies to explore for these deposits in a time- and cost-efficient manner. In the fall of 2012 we used a number of AUV-based technologies to explore and image a sulfide occurrence at the Palinuro Volcanic Complex in the Tyrrhenian Sea (Mediterranean Sea; Fig. 1) where sampling and drilling have documented a buried polymetallic barite-pyrite dominated site (Petersen et al., 2014). Sulfide mineralization is here covered by volcaniclastic and pelagic sediments and only red sediment staining and the presence of few tubeworm bushes indicated recent hydrothermal activity - black smoker venting is absent. We used AUVbased high-resolution bathymetry, sidescan sonar imaging, subbottom profiling, as well as magnetics to describe, in a quantitative way, the previously known sulfide-bearing areas as well as to successfully explore for new hydrothermal sites including large chimney structures (Figs. 2). Additionally chemical sensors (CTD, Eh, turbidity) investigated the water column for signs of hydrothermal activity in areas not previously investigated, but at the end, only weak anomalies were found in the southern part of the summit.

Sep 1, 2014

By J Youngson

Gold placers can be difficult to locate in areas where tectonic activity and paleogeography have changed significantly since placer formation. Existing placer exploration models are useful in areas that have a relatively simple geological history, identifiable relationships with parent sources, or a history of placer mining. However, exploration becomes increasingly difficult in areas where tectonic activity and sedimentary recycling repeatedly redistribute the gold. Gold placers in the Waitaki River catchment, North Otago, New Zealand have no primary source within the catchment. During the Eocene placer gold was transported by a river ('Buster River') that flowed in a northeast direction from Central Otago toward a coastline at Maerewhenua, North Otago. This river and coastal system was inundated by marine transgression during the middle Tertiary. Since the Miocene its placer deposits have been uplifted and eroded and any links with parent sources have been severed. Changes in paleogeography resulted in local reconcentration and local dilution of placer gold in different areas in the Waitaki catchment. Thin veneers of old Waitaki River gravels (Kurow Gravels), containing gold recycled from the older placers, have been deposited unconformably on strath surfaces cut into Tertiary or older rocks. These gravels along with remnant Eocene fluvial and shallow marine strata provide potential placer exploration targets. Uplift and erosion of non-auriferous rocks in the Waitaki catchment to the west and north of the study area has resulted in considerable dilution of potential placer deposits downstream, especially in areas of gravel aggradation. We present a placer exploration model that is founded on answering fundamental questions pertaining to the paleogeography and geological history of the sediments associated with the placers.

Jan 1, 1999

By R. J. Hundermark, L. R. Nelson

The critical importance of tap-hole design and management to furnace performance and longevity is explored through examining some of the specific matte, metal and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloys smelting and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally core aspects of tap-hole equipment and maintenance are identified that are considered important to securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance.

Jan 1, 2014

Shortly after Denny, Robson, and Irwin published their first paper in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery.It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter's source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in:(1) Speakers on machine columns, vibrated by drills.(2) Vials placed in drill holes to be blasted.(3) Both homogeneous and heterogeneous mixture with explosives.(4) Packages with tamping.(5) Compressed-air lines.(6) Special compressed-air ejectors for use while drilling and after blasting.(7) The discharge of ventilation fans.(8) The filters of respirators.It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium p;wder, and would interfere unduly with underground routine.Later, animal experiments by Denny, Robson, and Irwin2 showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.APPARATUS USED IN THE DEVELOPMENT OF ALUMINIUM PROPHYLAXIS SAMPLINGA basic requirement was a method of sampling to assess accurately the particle-size concentrations of dispersed aluminium powder. Konimetry, though regularly practised at McIrityre, was inadequate for the research in mind. On the other hand, the efficiency of the thermal precipitator was recognized as being very high. Accordingly, the latter instrument was chosen as best suited to our needs. Through the courtesy of the Ontario...

Jan 1, 1945

By George K. Burke

Jet grouting was first introduced into North America in the late 1970's, soon after the conception of the system in Japan. However, it was not until the mid-1980's that the technique began to gain acceptance through the renewed interest and efforts of specialist U.S. geotechnical contractors. Since this time, innovations by both American users and other users worldwide have further advanced the technology, with a corresponding increase in the range of practical applications. This paper discusses the evolution of jet grouting in North America, from simple single-fluid methods to more complex triple-fluid methods, to the energy-intensive double-fluid and SuperJet methods. Case histories, illustrating a variety of jet grouting methods and applications, are cited to support the newest United States applications.

Jan 1, 2002