Search Documents

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By Antônio Peres, Rogério Guimaraes, Lauro Takata, Harold Wyslouzil

"Serrana’s concentrator, in Araxii, has capacity of producing approximately 800,000 tomes of phosphate rock per year, with a P205 grade of 36%, from ores grading between 13% and 14% P205. The annual mining rate is around 3.5 Mt and the apatite is concentrated according to the following sequence: crushing, grinding, desliming, flotation and low and high intensity magnetic separations.Two industrial flotation columns (3.0 m x 4.5 m x 14.5 m) were commissioned in 1993 as a replacement for circuits of barite and apatite fines flotation. In 1994, four additional flotation columns of the same dimensions were put into operation, replacing 42 Wemco mechanical cells (300 ft3 each), in the barite pre-flotation, coarse apatite (two columns) and tailings regrind flotation Circuits. Overall, 66 mechanical cells (300 ft3 each) were replaced by only six flotation columns, designed by Cominco Engineering Services Ltd - CESL.The present paper describes the stages of process development, pilot plant testwork and implementation of the industrial project, highlighting the most relevant aspects of each of them. The results achieved are related to improvements in flotation selectivity, gains in P205 recovery and better process control, resulting in better quality products and lower production costs. Other benefits included a decrease in flotation reagents, electrical energy and maintenance materials consumption. These factors contributed to a significant decrease in the cost of phosphate rock production at Serrana, in Araxa - M G."

Jan 1, 1999

By M Logsdon, B Johnson, M Fordham

The underground Neves Corvo copper-tin mine in southern Portugal currently disposes of its tailings in a ætraditionalÆ wet tailings impoundment. With the development of new technologies for preparation and transport of thickened tailings or paste, alternative tailings disposal options have become available that provide a more sustainable water management system and a higher degree of environmental protection. In addition, growing European resistance towards subaqueous disposal may well result in mandatory use of dry disposal methods in the near future. Twenty-four tailings disposal alternatives were evaluated through a cost-effective and easily-implementable bench-scale geochemical screening program conducted at site. Since the tailings are pyrite-rich and highly acid generating, particular emphasis was placed on monitoring likely indicators of sulfide oxidation under the various simulated disposal scenarios. Dependent parameters investigated as part of the program included moisture content, use of alkaline additives (lime, cement), use of a bactericide, and agitation. Response parameters included paste pH, specific conductance, and temperature as indicators of oxidation. The testing was carried out for 30 weeks. Results indicate that a number of relationships between the geochemical stability of the samples (ie sulfide oxidation) and sample characteristics can be readily identified. Based on the results of the screening program, a limited number of tailings mixtures have been selected for further long-term testing in field weathering cells to aid in the identification of the optimal mix design for future tailings disposal at the Neves Corvo Mine. This type of testing provides an inexpensive and reliable methodology for semi-quantitative comparison between tailings disposal alternatives, in particular at locations where more rigorous evaluation through long-term, fully replicated testing is not immediately feasible.

Jan 1, 2003

Evaluation of Comminution Circuit Design for Sustainability Using EcoNomicsTM

Sep 13, 2010

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005

By G T. Kukla

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland û Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground subsection of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes operational. Support of the site's system continues from head office which is continually involved in development of SUMPS and issuing revision updates to sites. The users, as well as programmers, were mostly geologists and mining engineers. This helped to ensure rapid, successful implementation. The broad approach of this system was to use interactively the specialist skills and interpretative abilities of the user mining engineers and geologists with the data manipulation abilities of the computer. It is an integrated system which covers geological exploration, deposit modelling, mine planning and production scheduling. An important feature of the system is that the user has full interactive control over each function through a graphics terminal where applicable.

Jan 1, 1980

By W. W. Stephens

As part of the Bureau of Mines program directed toward more effective utilization of the mineral resources of the United States, a number of processes for production of sponge iron have been investigated. The use of sponge iron as a raw material for production of steels and other ferrous alloys offers several possible advantages over the conventional pig-iron and scrap process, especially for utilization of the smeller, widely distributed iron-ore deposits of the western United States. Although considerable information has been made available on various processes for production of sponge iron, little information 118.6 been published heretofore on the problems and costs involved in melting the sponge iron for production of steel. The present Paper reports the results of tests conducted at the Bureau of Nines pilot plant at Redding, Calif. in which several different types of sponge iron Were used as charge material for production of steel in a 4-ton-capacity basic arc furnace.

Jan 1, 1949

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R. M. Goktan

Point-attack picks are one of the most widely used tools for the mechanical excavation of rock and coal. In the literature, some practical formulas have been developed to estimate their performances under varying cutting conditions such as the pick geometry, cutting depth and cutting geometry. In this study, it is shown that Evans?s theoretical model, the most cited in the literature, has serious limitations concerning the changes in the cutting geometry. Analysis of the two independent full-scale linear rock cutting experimental data reveals that both his theory and its recent modification can not fully explain the mechanism of rock breakage under asymmetrical attack. The cutting force predictions made by employing such models are shown to be too significantly weak to be of any service in practice. In this study, a semi-empirical approach was followed by means of which cutting forces under varying cutting geometries could be made. By analysing the full-scale rock cutting test data, prediction equations of the peak cutting force and mean cutting force have been developed. Comparisons of laboratory determined and predicted force values indicate that the suggested prediction equations are applicable to quite different rock materialsm which have uniaxial compressive strength in the range of about 30?170MPa, and valid for different cutting geometries. It is also shown by regression analysis that the established prediction equations are statistically significant.

Jan 1, 2005

By Xin Zhou, Huilin Jia, Xiaofei Liu, Jinxin Wang, Zifeng Meng, Zinan Du, Hui Xie, Guihang Jiang

The change of gas emission or concentration level at the working face is one of the main precursor characteristics of coal and gas outburst. At present, coal and gas outburst monitoring and early warning are mainly based on whether it exceeds the limit and its change law. However, the gas concentration level is affected by factors such as coal seam gas content, permeability, and mining process, and the change law is complex to recognize manually. In this paper, the response characteristics of gas concentration level in the mining process are analyzed and revealed, and a bidirectional long short-term memory model is established. The change characteristics of the gas concentration level in the mining and non-mining processes are studied and recognized. The results show that the change law of gas concentration in the mining process has apparent periodicity and trapezoidal volatility. The proposed intelligent recognition method based on the bidirectional long short-term memory neural network can automatically recognize the underground mining and non-mining processes, and the recognition accuracy achieves 97.7% . The research can significantly help improve the level of coal mine safety management and the accuracy of early warning of coal and gas outburst.

Apr 29, 2023

By Mark I. Copeland

This study was conducted by the Bureau of Mines to determine the effect of steel reheating practices in burning natural gas on the amount of silicon required to prevent the formation of copper on steels containing up to 1 wt-pct Cu. Formation of copper, which causes surface hot shortness, was readily prevented by as little as 0.3 wt-pct Si and by 2 vol-pct excess oxygen in the furnace atmosphere when reheating steels containing up to 0.8 wt-pct Cu. Up to 0.8 wt-pct Si content and careful control of reheating conditions were necessary for steels containing 1 wt-pct Cu. Best conditions for these steels were reheating to 2,200° F (1,205° C) in burning gases containing 2 vol-pct excess oxygen, and then to higher temperatures in gases of 6 vol-pct excess oxygen. Slag and mold wash were not detrimental on steels reheated for 8 hr by a soaking-pit-type furnace schedule, but they were problematical on steels heated for 2 hr by a pusher-type furnace schedule. The effect of silicon contents on scaling rates also was determined.

Jan 1, 1974

By R. E. Head

This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing, from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperative microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau of Mines, the Utah Copper Co., and the University of Utah.

Jan 1, 1935

By J V. Mehrabani, A R. Sayadi

Adequate estimation of equipment costs is a key factor in a feasibility study and in evaluation of design alternatives for mining and mineral processing projects. Inaccurate early cost estimation could lead to the elimination of investment benefits. However, this estimation is complex and time consuming because of data accessibility problems and consequently access to a rapid, up-to-date and accurate tool is desirable for carrying out cost estimations.This paper describes the development of models for estimating capital and operating costs for a jaw crusher, which is used as the primary crusher for a wide variety of mineral beneficiation plants, applying single and multivariate regression analyses, together with the design of experiment approach, based on principal component analysis. Explanatory variables include gape size, length of feed opening and power as numeric (quantitative) variables and toggle type (single or double) and the existence of extra heavy duty construction as categorical (qualitative) variables. The performance of each model has been investigated and comparing the estimated R-squared (R2) of each model, the best was selected and its validity examined. The cost models include the capital and operating costs along with the operating cost components. The results indicate that the suggested best cost model is sufficiently accurate for use in feasibility studies.

Sep 26, 2011

By Philip E. Niebuhr

A procedure, which can be performed in the field by nonanalytical personnel, is given for sensitive spot tests for detecting tellurium or selenium. The expressed need of a field test for detecting small amounts of tellurium, which may be accompanied by relatively large amounts of selenium, has led to the development of this method. Tellurium search has been impeded by the lack of a satisfactory test from the standpoint of sensitivity and specificity. A quantitative laboratory method exists, but it is expensive and relatively laborious. Several other qualitative tests are known, but they require unstable solutions, which must be freshly prepared for use, and a greater variety of laboratory equipment. The particular advantages of the test described are its simplicity and the stability of the reagents required, there-fore is is well adapted for field use. Also, this test was found to be of practical use in the analytical laboratory when screening samples, thereby reducing analytical costs. The roughly quantitative interpretation of the results can save time by indicating the approximate size of the sample taken for a quantitative determination.

Jan 1, 1962

By C. Pitzer

"Safety performance in many companies and even industries has stalled in the last decade. Accidents rates are at a “plateau” and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas Refinery disaster, organizations that have “exemplary” safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Classic examples are the Piper Alpha disaster and NASA’s Challenger and Columbia disasters, the BP’s Deepwater Horizon Rig disaster in the Gulf of Mexico. Looking into the causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization’s mindset, or its culture? What characterizes these organizations’ decision-making, their approach to safety and to risk and are there features that can be delineated? The research and review presented in this paper covers a period since1995, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions of near zero organizations (NZO) that suffered unexpected disasters, based on extensive research by the author. More recently, the massive West Fertilizer plant explosion in Texas, and the Train Disaster in Lac-Mégantic, Quebec, Canada underlined the same trends. Organizations may experience calamities not because they are bad, or unsafe, but because they have become “cult-like”. INTRODUCTION The train disaster of 6 July 2013, in the small town of Lac-Mégantic in Quebec, Canada, in which 47 people were killed, had many strange pre-cursorsso-called “black swan” events that have occurred in many different industries. Black swan events are so rare, that there is almost zero chance that they will ever occur again, but they are so calamitous that the responses to these are emotional and irrational, (but necessary) and in those responses, the seeds for other, different black swan events are put into place. It is not what we don’t do, or do wrong, that causes modern disasters, it is what we do. The same things in the culture that make us successful, may also cause the disasters. We slowly, incrementally and insidiously ‘float’ into disaster. One such Black Swan event: The Piper Alpha Oil Rig disaster, killing 167 men in the North Sea on the 6 September 1988, was one of the most pivotal events in safety around the world. It changed the thinking and focus of governments, whole industries and led to numerous books and papers. It resulted in new legislation, textbooks and a critical self-examination by the oil and gas industry."

Jan 1, 2016

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that effects the net expansion of the change in both industrial and test ovens. Various test results5/ have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; but no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors.]

Jan 1, 1940

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By Erik Pérez, Emanuel De la Cruz

El Despacho Remoto es un sistema de Control y Monitoreo de Flota operado desde el hogar, Implementado por Antamina, que permite a los operadores de despacho monitorear y controlar los equipos de carguío y acarreo desde casa, evitando el riesgo de contagio a la Covid-19 asociado al traslado y estadía en mina asegurando la salud del despachador, mejorando su labor en la operación y la satisfacción laboral del despachador. Cada estación de Despacho Remoto se implementó con los mismos equipos de Mina, conectados mediante internet de fibra óptica y una VPN (Red Privada Virtual) desarrollada especialmente para el trabajo de Despacho Remoto, además reforzamos los canales de comunicación con los operadores y supervisión.

Sep 30, 2022

By A. Nivala, S. Ulgiati, M. Canino

Mining and processing of bastnaesite ore, (Ln)CO3F, for lanthanides extraction is investigated in this paper. This series of elements proved to be applicable for a wide range of high-tech uses. In spite of the strategic importance of lanthanides, no LCA and energy analyses of their extraction have ever been published. We perform in this paper a Life Cycle Assessment of the Lanthanide production cycle, based on available database and literature data from Mountain Pass mine (USA) and other worldwide mining and processing sites, most of which in China. We investigated three main steps: mining, milling (including transport, grinding and drying), and flotation (for lanthanide chloride extraction). We do not investigate here the separation of pure oxides from lanthanide chloride, a compound which is also marketed as such. The conventional LCA was integrated by means of energy and emergy evaluations, aimed at investigating respectively the global energy cost and the environmental sustainability of the process. Indicators of material intensity, thermodynamic efficiency, and environmental impact (including LCA and ecological footprint impact categories) are calculated and discussed.

Jan 1, 2005