Search Documents

By F. Tailoka, G. Zhao

Pb is an unwanted impurity in Al for which there is no established method of removal. As it interacts strongly with alkali metals, separation was achieved by adding Na or K to molten Al at 953-1 003 K. Direct Na addition led to considerable evaporative loss but in-situ addition by electrochemical titration from a eutectic NaCl-KCl or KCl-BaCl2 mixture was found far more effective, in some cases reducing Pb content below detection levels within 2 h of titration. K appeared more effective than Na at low Pb concentrations but the use of Na was preferred as it is less toxic and explosive. Na removal from Al-Na and Na-Pb alloys was also carried out electrochemically, the use of these two alloys rather than the eutectic salt as a source of Na avoiding liberation of Cl2 at the anode

Apr 1, 1995

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By Donald A. Bruce

The construction of major structures in karstic limestone terrains poses difficult problems to designer and contractor alike. This reflects the inherent variability of such conditions, and also the significant impacts caused by the construction processes themselves. Three case histories are provided of recent projects in the United States: the sealing of a major inflow into a quarry, the improvement of a highly loaded bridge pier foundation, and the installation of high capacity micropiles. Emphasis is placed on problem assessment and execution verification.

Jan 1, 2002

By L. A. Morley

Volume III of the final report examines the indication versus interruption procedures used on motion-drive power equipment, with emphasis on surface excavators. The report begins with a review of the electromechanical acid conversion used with the Ward-Leonard control system. Protection criteria for the drive-system components are then discussed. Fault sources and fault calculations for both the ac supply source and dc power loop are introduced to assist in discussing indication and interruption procedures. The subject is then expanded to examine the dynamic process of the machine and determine the effects of fault current and position of the machine to allow for an orderly shutdown. With this analysis, possible indication an interruption procedures are given for the four-quadrant duty cycle of excavators. The report concludes by introducing other mining operations that utilize similar motion-drive systems and also static (solid-state) drives and recommends further research in these areas, as well as a more detailed examination of the dynamic fault analysis for excavators.

Jan 1, 1982

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By Ken Cross

This paper aims to demonstrate that explosives organizations and workers have a legal, moral and financial duty to be able to demonstrate their competence when required, and how that may be achieved at any level from explosives storekeeper to senior explosives engineer on a major project. The concept of competence is outlined, as are the benefits to members of staff, management and the organization, particularly in a regulatory regime that includes competence management as a key performance indicator.

Jan 1, 2013

By V. A. Nieberlein

The purpose of this investigation is to determine the reserves of columbium (niobium) minerals in Arkansas and to develop metallurgical methods for concentrating the minerals and extracting the metal. The columbium resources of central Arkansas were explored by drilling and trenching, and a number of samples were taken. On the basis of this exploration the known reserves of the metal were estimated to be over 78,000,000 pounds. The reserves could possibly be extended by additional exploration to 150,000,000 pounds.

Jan 1, 1954

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By Paul M. Tyler

[This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of specified French possessions in Africa has been prepared from the best information available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it is being referred through the courtesy of the Department of State. France controls large areas on the African continent, but the various Colonies and Dependencies are administered more or less independently. Algeria is under the direct jurisdiction of the Ministry of the Interior, and its mining laws are essentially the same as those of the mother country. Tunis and Morocco are attached to the Ministry of Foreign Affairs; separate digests of the mining laws' of these respective colonies have already been prepared by the United States Bureau of Mines. The present paper covers all other French territory on the continent of Africa except Somaliland, a rather small Colony including the port of Djibouti near the point where the Red Sea joins the Gulf of Aden. Available information indicates that the prospects of mineral production in this Colony, apart from salt and gypsum, are not at all encouraging.3]

Jan 1, 1933

By James J. Neate

The augered cast-in-place pile system came into use in the late 1940's where various techniques were tried using pressure grouting methods. In the early development stages some piles were installed using the preplaced aggregate concrete system. As development continued it became more apparent that placement of coarse aggregate was more costly than making a pile out of a cement and sand mixture only. Various techniques were tried consisting of pumping structural grout into an open hole through a pipe left in the bottom of the hole, drilling or driving a pipe in close proximity to the tip elevation of the auger or in working a pipe down adjacent to the auger fluting. For these techniques the pipe was usually withdrawn after grout appeared at the surface. In 1951 a patent was applied for by Raymond Patterson describing the above techniques along with a technique for placement of grout using a hollow stem auger and a removable plug or lead bit at the tip of the auger. The plug or lead bit was removed by grout pressure and this would be an expendable item for each pile placed. The patent was granted in 1956 and patent rights were assigned to Intrusion-Prepakt, Inc. Shortly thereafter other contractors were granted licenses to utilize the system. Patent coverage expired in 1973 and this method now is in the public domain. Today the method is in wide use throughout the world and is particularly well accepted in Japan and England.

Jan 1, 1988

By A. M. Hefny, F. P. Siew, P. G. Ranjith

Fracture initiation and propagation, being one of the most intensive subjects in rock mechanics; contribute significantly to the deformation of jointed rock masses. An experimental study on fractured granitic rock was carried out to determine the peak strength of specimen under triaxial loading conditions. The commonly observed failure mode for rock specimens in this study was found to be the shearing of the plane of weakness. The minimum peak strength of fractured rock is observed when the joint orientation is approximately 70° to the horizontal axis. Based on experimental test data, an empirical expression was developed to accommodate the effect of joint orientation and joint trace length in estimating the peak strength of fractured rocks. The predicted values of peak strength using the proposed equation well agree with the experimental results carried out on singly fractured specimens under triaxial loading conditions. The threshold stress values of crack initiation and propagation depend on joint geometrical parameters, their degree of interconnectivity, as well as surrounding stresses on the fracture plane.

Jan 1, 2003

By J. D. Rice, S. C. Pitzer, C. E. Thomas

Interpretation of pressure build-up data obtained in the conventional manner has often been difficult because of the deviation from theoretical behavior. Major causes of this deviation have been attributed to damage and afterflow, and to fluid redistribution in the wellbore which, in extreme cases, can result in a pressure hump in the early portion of the build-up curve. Theoretical investigations show that bottom-hole pressure is definitely influenced by phase redistribution in the tubing column during surface shut-in tests, and that the magnitude of the effect is sensitive to the producing gas-oil ratio and stabilized rate of flow in the well. For field experiments a wire-line tubing packer, which can be run in the tubing against a stabilized flow rate, was developed for bottom-hole shut-in tests. By use of this bottom-hole .shut-in method, pressure humps previously observed in surface shut-in tests were completely eliminated and the effects of afterflow minimized. Analog and digital computer studies have been made to obtain theoretical curves for comparison with field curves, and remarkable agreement between the results of bottom-hole shut-in tests and theoretical curves has been obtained. INTRODUCTION Pressure build-up data from shut-in wells have been used by the petroleum industry to determine the permeability of the formation, to estimate wellbore damage, to evaluate the static reservoir pressure and to speculate reservoir volume. Calculation of these factors is based on methods of analysis developed for theoretical systems whose build-up curves have a charac- teristic shape when the wells are shut-in at the sand faCe.1,2,3,5,8,10 However, field curves obtained by conventional surface shut-in methods do not always exhibit this characteristic. Such factors as stratification, rock heterogeneities and irregular reservoir geometry can cause the character of a build-up curve to deviate from that predicted by theory for a simple system. In addition, all field build-up data are affected by the methods utilized in obtaining the measurements. Conventional surface shut-in techniques allow two effects to occur which contribute directly to the manner in which pressure builds up at the sand face. The first, afterflow, has been recognized for some time and methods are available for estimating the magnitude of its effect and for correcting its influence.' The second, phase segregation in the tubing column after shut-in, has been reported only recently and appears to exert a considerable influence on the character of field build-up curves.!' In extreme cases, phase segregation can produce "pressure humps" in the early portion of the build-up curve. Such curves have been considered anomalous and have defied analysis. It is the purpose of this paper to discuss the effect of phase segregation in the tubing string during build-up and to present a bottom-hole shut-in technique for obtaining field build-up data which minimizes the influence of afterflow and eliminates phase segregation effects. It will be shown that reliable reservoir information can be calculated from build-up measurements obtained using this method, even though conventional surface shut-in tests on the same wells yield anomalous data. DISCUSSION OF PHASE REDISTRIBUTION EFFECTS Some of the effects of phase redistribution on pressure build-up curves have been described previously by Matthews and Stegemeier" who have presented evidence that phase segregation is responsible for the pres-

By C. J. K. Purdy, H. E. Jamieson

"The comprehensive assessment of the environmental impacts of mining rare earth element (REE) deposits depends on a sound knowledge of the mobility of REEs in low-temperature aqueous environments. Temperature, pH and water chemistry are important factors controlling the aqueous mobility of REEs, while REEs are known to readily form complexes with both inorganic and organic ligands, and it has been shown that sorption and colloid formation may play an important part in dictating REE transport in the low temperature weathering environment. Ore and host rock mineralogy is also a key factor controlling the extent to which REEs are leached from mine waste. INTRODUCTIONThe aqueous mobility of rare earth elements (REEs) has commonly been explored in the past due to their potential application as tracers of geochemical processes in aqueous systems. REE mobility in low-temperature solutions has been shown to be dependent on the pH, temperature, ionic strength, and solution chemistry. For example, the aqueous transport of REEs can be modified by complexation with organic and inorganic ligands (Johannesson & Zhou, 1999; Klungness & Byrne, 2000; Luo & Byrne, 2004; Schijf & Byrne, 2004; Tang & Johannesson, 2010; Wood, 1990, 1993), or through sorption to suspended particles and colloids (Bau, 1999; Quinn, Byrne, & Schijf, 2004, 2006a, 2006b, 2007; Sholkovitz, 1995). Here we review the coordination chemistry, sorption behaviour and potential colloid association of REEs with respect to low temperature aquatic settings.RARE EARTH ELEMENT CHEMISTRYREEs include lanthanum to lutetium of Group IIIA in the periodic table. All share very similar chemical and physical properties. Often included in REE studies is another Group IIIA element, yttrium owing to its similar properties, and occasionally scandium, although its considerably smaller ionic radius makes for different properties and will not be discussed further here. The REEs are often subdivided into the light REEs (LREE), La to Sm, and the heavy REEs (HREE), Eu to Lu, which also usually include Y (hence are often referred to as YREE). The REE may be subdivided further into the LREEs, middle REEs (MREEs), and HREEs, in which case each classification includes La-Nd, Pm to Ho, and Er to Lu as well as Y, respectively, although definitions vary throughout the literature."

Jan 1, 2012

By Gordon R. Sima, John L. Bennett, Roger L. King

Electric shocks are a serious problem in the mining environment. Because of extremely wide ranging use of electrically powered equipment in the mining industry, the hazard to personnel due to electrical shock and related injuries are not restricted to any single area but cover the entire spectrum of mining activity. Electrical accidents, resulting in personal injury, due to im- proper or complete lack of grounding of electrically operated mining machines, form a significant percentage of the overall electrical accident picture. The object of this paper is to describe methods of detection of unsafe electrical conditions with respect to the grounding of electrically operated mining equipment. It also includes a discussion of prototype instruments which effectively monitor the condition of the grounding safety devices currently in use on mining equipment and warn of dangerous conditions as soon as they appear. The paper is based on work accomplished under USBM Contract Number 50357115. The contract was initiated under the Pittsburgh Mining and Safety Research Center Program. It was administered under the technical direction of PM and SRC with Mr. Roger L. King as the Technical Project Officer. Mr. Daniel B. Dawkins was the Contract Administrator for the Bureau of Mines.

Minerals processing needs a step change in energy efficiency. While the search for new technology breakthroughs is important, huge gains are still available by better using existing research outcomes. This potential remains untapped due to a combination of organisational 'silos', inappropriate performance measurement, and poor science in some areas. It is time to see the elephant in the mill.

Sep 13, 2010

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Diego Ruben Martin

Este trabalho objetivou comparar, por meio de experimentos desenvolvidos em uma fundição, através da adição de três inoculantes diferentes (IM-22 com FeSi-Ba/Zr, G 20 com FeSi-Ba) e IMSR 75 com FeSi-Sr), para observar as características da vida util de ferramentas na usinabilidade das peças, microestrutura e propriedade mecânica. A metodologia da pesquisa se baseou em analisar principalmente pelo processo de fresamento o ferro fundido cinzento GG-25 inoculado diferentemente, denominado de acordo com a Norma DIN EN 1561. As formas de avaliação dos resultados terão como base uma análise quanto ao desgaste da ferramenta, acabamento superficial, análise microestrutural, composição química e propriedades mecânicas do material da peça. Os resultados mostraram que dentre os inoculantes aplicados o com Sulfeto de Estrôncio (SrS) apresentou-se mais estável termodinamicamente que as amostras inoculadas com os outros dois inoculantes, pois ele levou a uma variação da energia livre de Gibbs mais negativa e portanto mais favorável a formação de núcleos com raio crítico (rc) maiores, o que permitirá uma solidificação com nucleação heterogênea. Todavia o respectivo inoculante também foi mais eficiente na formação de uma microestrutura mais estável, com maiores quantidades de células eutéticas e vida útil do inserto mais longa quando usinado.

Aug 16, 2017

By Duanyou Li, Qing Xiao, Zhiwang Wang, Xiaoqing Gan

"Seepage is a major cause of earth-rockfill dam failure. Numerical simulation of infiltration process, distribution of drift, flow velocity and direction after the impoundment can guide seepage control and evaluate its effects. A double field coupling model is established based on soil consolidation theory and the interaction between the seepage field and the temperature field. The simulation is implemented under the situation of core wall setted, core wall not setted, and core wall setted with concentrated leakage. The results indicated that the saturation line height was significantly reduced due to impervious core wall, and the temperature distribution is uniform above the saturation line. If concentrated leakage occurs, temperature distribution of dam was significantly changed, which is consistent with theoretical inference.INTRODUCTIONEngineering seepage field distribution must be calculated in seepage control design, optimization, and correction of new engineering construction of earth dams, as well as in seepage monitoring and evaluation of existing earth-rockfill dams. The aim of calculation is to identify the important parameters in seepage field, such as the coefficient of permeability, seepage flow, pressure, head, and allowable seepage slope, for effectively implementing seepage control design, correction, safety assessment, and anti-seepage reinforcement. These seepage parameters usually can be obtained by in-situ test and back-analysis based on reliable monitoring data.In order to obtain reliable monitoring data and reflect the earth-rockfill dam seepage state and change process, appropriate monitoring technology and monitoring method is necessary. The traditional seepage monitoring method is through site inspection and sensors (e.g., osmometer, piezometric tube and measuring weir) that buried in the structure and its foundation. However, there are still some disadvantages:"

Jan 1, 2015

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By using knowledge-based technology to create a Virtual Mining Enterprise and integrating it with existing technical and financial computer systems, a gold mining company has been able to reduce the time taken to produce a mine plan from 14 weeks to less than one week. Typically, the mine planning process requires circulating and managing large amounts of information. Even with the use of computers in todayÆs business, this is often still a manual process involving file transfers and individualised spreadsheets. Mine planning also involves understanding and managing large quantities of complex and interrelated variables. Added to this is the ever changing dynamics and constraints associated with the business of mining. These issues not only hamper the planning process but also question the validity and usefulness of the mine plans being generated. By integrating the information and knowledge of the numerous departments involved in mine planning into one core Knowledge Base - so called æone version of the truthÆ, - mining companies are able to overcome these pitfalls experienced in traditional planning methods. Once set up, the Knowledge Base creates and runs a virtual mining enterprise with which to visualise and test various scenarios of mining, business and logistical activities. The final output is an optimised enterprise-wide plan with clear and detailed instructions for each of the divisions of the company.

Jan 1, 2000