Search Documents

By James W. Myers

"Packaged fuel" is the trade name applied by the industry to a product consisting of coal screenings and a binder compressed into 3 -or 4-inch cubes and wrapped (six or eight in a package) in sturdy paper and sealed with gummed tape. Parry describes the product in greater detail and distinguishes clearly between packaged fuel and briquettes. The industry developed from the desire of retail coal dealers to improve utilization of the relatively large quantities of slack sizes that result from the degradation, during shipping and handling in the yard, of friable coal, particularly Pocahontas coal. During the war an attempt was made to apply this technique to anthracite fines, and a recent publication of the U. S. Bureau of Mines reported the results of physical and combustion tests on packaged fuels containing anthracite fines. References made in this report to the previous investigation on packaged fuels containing anthracite represent data or conclusions presented in Report of Investigations 3882. This investigation was conducted as a continuation of the previously reported studies and consisted of physical and combustion tests of packaged fuels made from high-volatile bituminous coal, as well as the low-volatile bituminous coal ordinarily used in the industry, to determine their relative suitability for domestic firing. Particular attention was given to the smoke-producing properties of the packaged fuels because of the increasing importance of the prevention or reduction of smoke from hand-fired domestic heating plants resulting from the widespread enactment of smoke-prevention ordinances.

Jan 1, 1951

By Donald J. Frendzel

The post-World War II expansion of the Soviet petroleum industry has established the U.S.S.R. as a major oil-producing nation and has led to Russian reentry into the international petroleum trade. The rapid growth of Soviet petroleum production will allow the U.S.S.R. to displace Venezuela as the world's second largest oil-producer in 1960 and to narrow further the gap between Soviet and U.S. crude-oil production. U.S.S.R. crude oil output was only a tenth of U.S. production in 1946, but it will be more than a third at the end of 1960 and more than half in 1965. The Soviet Seven-Year Plan (1959-65) for oil provides for substantial increases in petroleum production, refining, storage, and distribution facilities. Crude oil production and primary distillation capacity are to double, considerable storage capacity is planned, and pipelines for crude oil and petroleum products are to increase threefold. According to the Soviets, the initial phases of this plan (1959 and 1960) have been completed successfully. However, this progress has been achieved with difficulty.

Jan 1, 1961

Large scale fluid extraction from the Latrobe Group in the Gippsland Basin is occurring as a result of offshore petroleum production and coal mine dewatering in the Latrobe Valley. Groundwater extraction in the Latrobe Valley exceeds recharge and is causing an expanding area of declining hydraulic head in the Latrobe Group, and regional land subsidence which is well documented. Recently the government water sector completed the installation of a network of Latrobe Group monitoring bores in the remainder of the onshore part of the Gippsland Basin. The bores situated along the coastal area show a steady decline in hydraulic head of about 1 m/year which can be attributed mainly to petroleum production.

Jan 1, 1992

By Caithness SJ, Heape JMT

Following the discovery by CRA of gold at Mt Kare, and the subsequent 1988-90 gold rush, mechanised mining of the alluvial resource is now being carried by a company jointly owned by CRA (51%) and landowners of the area (49%). Mining is currently being carried out using small gravity processing plants fed by hydraulic excavators. Use of hydraulic mining techniques will be limited to over- coming difficulties related to the high clay content of the material and the soft nature of the bedrock. Current resource estimates suggest that the alluvials will have a mining life of three to four years. During this time, exploration of the hydrothermal gold mineralisation at Mt Kare will be carried out by a wholly-owned company of CRA. It is hoped that this will lead to establishment of an economic primary gold resource.

Jan 1, 1991

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.

Geophysical surveys are currently being carried out over mineral prospects all around the Pacific Rim. Many of these surveys are successful in locating mineralisation in porphyry intrusives, mesothermal environments, and epithermal vein systems. A number of examples of surveys in Indonesia and Papua New Guinea are presented, which show the successful application of various geophysical techniques to the discovery of mineral deposits on the Pacific Rim.

Jan 1, 1999

After the Loma Prieta Earthquake, which caused major damage to viaducts in the Bay Area, the California Department of Transportation set up a test programme for foundation piles. Funderingstechnieken Verstraeten B.V., beter known as Fundex, was approached, since one of the piling systems of Fundex, named Tubex, is extremely suitable in areas sensitive to earthquakes and we were very much interested to prove the capabilities of this piling system. Equipment For the installation of Tubex and Tubex grout-injection piles special piling equipment is required. Since our company is not only a contractor, but also a designer and manufacturer of piling equipment, all special equipment for our range of foundation techniques is designed and built by our own piling equipment department. For the installation of both Tubex piles and Tubex grout-injection piles for the Caltrans test programme, the following pieces of equipment were selected: a) Fundex F12 piling rig b) Drill table c) Hydraulic powerpack d) Grout mixing unit and high pressure pump

Jan 1, 1993

Tougher physical mining and processing conditions as well as economic circumstances are causing many mining companies to re-evaluate the effectiveness of their mine planning. The recent wave of inexpensive computing power provides the engineer an opportunity to go beyond the simple one-off manual mine design and production schedule. The basis of a good mine plan is a good reserves model. Concepts of mine model development are explored. The only advanced computer methods that have found consistent success in optimising mine planning functions are economic pit limits determination and material scheduling. Three pit 'optimisation' methods are examined; the moving cone, the Lerchs-Grossman 3-D graph algorithm, and the new network flow algorithm. A comparison between the methods in terms of total profits generated and computer time involved are made. The results show that both algorithms produced a higher profitability than the simple moving cone, but at much higher execution times. However, the profit increase never exceeded much more than 1 % of the base moving cone case. Finally, a method for the development of long range material production schedules with forward waste planning is presented.

Jan 1, 1989

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005

By Patrice Favreau

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commerical computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1992

By Arthur Darby

The city of Kuala Lumpur was founded in 1857 by miners seeking tin near the confluence of the Klang and Gombak rivers. The rapid development of the city and surrounding area since independence has led to more rapid runoff during rainstorms and to gradual canalisation of the rivers with some restricted sections. The outcome has been more frequent and more severe floods (Abdullah 2006). At the same time the centre of Kuala Lumpur has become a modern inter-national city with tall office buildings, hotels, and shopping centres connected by a network of wide roads and commuter rail systems. With these the cost of dislocation during floods has risen as has the cost of making good damage afterwards. The Government of Malaysia considered these consequences unacceptable and sought ideas from the private sector for a solution. Potential solutions consisted of variations on the themes of bypassing the city centre with a flood relief tunnel or of providing off channel storage or a combination of both. Since under Malaysian law a tunnel cannot be constructed under private property unless this is first purchased or agreement reached with the owner, it was necessary for most of the tunnel alignment to run below existing heavily congested roads. After considering these facts Gamuda Berhad and MMC Berhad, two leading Malaysian development and construction companies, decided to propose to Government an innovative solution in which the tunnel would be used to carry road traffic except during floods.

Jan 1, 2008

The use of comparative sampling methods during the evaluation of the tin-copper deposits at Cleveland mine yielded closely checking average results from groove, channel, AXT split diamond drill core, and bulk sampling for both tin and copper content of the ore.The weighted mean tin and copper grades and values for the groove, channel, and split core samples showed small percentage differences from bulk sample results, and the F-ratio test for single population origin of the four types of samples was accepted at the 99· 5 per cent level of confidence.These results indicate that grade estimates based on the assays from AXT split diamond drill core and/or groove samples would be reliable within practical limits.

Jan 1, 1968

THE township of Costerfield is situated in the parish of Costerfield, county of Dalhousie, and lies 6 miles east of Heathcote and 30 miles south-east of Bendigo. It is separated from Heathcote by the Mt. Ida Range, which forms the western boundary of the Silurian formation. It is situated at the head-waters of Tin-pot Creek, a small southerly tributary of the Deegay Ponds Creek, which flows east to the Goulburn River.The field was discovered in 1860 by two prospectors, Coster and Field, who were guided there by a shepherd, M Nicol Coster and Field had already discovered an antimony lode about three miles nearer Heathcote, when M Nicol offered to guide them to the larger outcrop. The main Costerfield reef at that time projected above the surface, and was white through oxidation, though the bluey sulphide showed on fracture. No alluvial gold of any consequence was obtained at Costerfield, but a little was obtained, at Redcastle, 7 miles to the north, and in some of the gullies to the east.Following its discovery there came a period of prosperity to Costerfield, while the mining operations were confined to the oxidized zone. The early success of mining at Costerfield was due to the gold values, and it is probable that the oxidized zone was secondarily enriched. The earliest available record of values is a crushing of Coster and Co. on the Antimony reef (now known as the Costerfield reef), when 200 tons from a depth of 70 ft. averaged 4 oz. per ton in July, 1861. At this time a crushing mill had not yet been erected at Costerfield, and the ore was carted and treated at Redcastle. The massive antimony ore, consisting of mixed oxides and sulphides, was separated by hand-picking as "marketable ore," and the remainder crushed for gold. A higher average is recorded from South Costerfield in September, 1861, when a 15' cwt. parcel...

Jan 1, 1922

Due to the reduction in frictional resistance, the characteristics of joint infill have a major role to play on rock mass instability. This paper elucidates the laboratory behaviour of graphite infilled joints based on a large-scale shear apparatus under constant normal stiffness (CNS). Discontinuities in a graphite mine have been simulated using high strength gypsum plaster, with the joints infilled with compressed graphite layers. The Fourier series was employed to characterize the joint surface, and the method of using the Fourier coefficients for the prediction of dilation and normal stress with displacement is explained. Die Charateristik von Verbindungsfüllungen hat einen wichtigen Einfluss auf Felsmassenstabilität aufgrund der Verringerung des Reibwiderstandes. Diese Veröffentlichung untersucht das Verhalten von Graphit gefüllten Verbindungen im Labormaßstab mit einer Methode die auf einem gross-umfang Apparateprinzip unter konstanter Normal-Steifheit beruht. Unregelmässigkeiten in einer Graphit Mine wurden mit Gypsum Gips von hoher Festigkeit simuliert, die Verbindungen wurden mit kompressierten Graphitschichten gefüllt. Fourier Reihen wurden angewandt um die Verbindungs Fläche zu Characterisieren. Die Methode die verwendet wurde um die Ausdehnung und Normalkraft mit der Verschiebung mit Hilfe von Fourierkoeffizienten zu bestimmen wird beschrieben. Due à diminution des résistances par frottements, les caractéristiques des joints de remplissage joue un rôle majeur sur les instabilités de la roche. Cet article étudie le comportement en laboratoire des joints de remplissage en graphite à partir d’un dispositif de friction à grande échelle sous rigidité normale constante. Les discontinuités dans une mine de graphite ont été simulées grâce à un plâtre à haute teneur en gypse, dont les joints ont été remplis de couches de graphite compressées. La caractérisation de la surface des joints a été réalisée avec les séries de Fourier. La méthode utilisant le coefficient de Fourrier pour la prédiction de la dilatation et de la compression en fonction du déplacement est également expliquée.

Jan 1, 2003

By C. E. Rodgers

WHEN I was asked to prepare, for presentation at the 1938 Annual Meeting of the Institute, some data concerning low-discharge grinding at the Sylvanite mill, it seemed entirely reasonable to expect to have at my disposal the results of at least four full months' operation after the last unit, as then proposed, was installed. Delays in delivery of equipment, nevertheless, shortened the interval, as will be shown herein. In submitting the data contained in this discussion, I wish distinctly to state that the intention is not to claim that final conclusions can be reached at this time concerning our operation. Test periods, in certain instances at least, have been too short for this purpose, although some, where so stated, have been extended through March and April. It is hoped, however, that an advantageous trend in practice can be shown and that the experience related may be of interest to others who are now operating, or who are considering the operation of, low-discharge grinding mills. In the plant under review, four mills are in use: one primary and three secondary. Present mill capacity (grinding, as shown by screen test, about 99 per cent through-200-mesh and approximately 88 to 89 per cent minus-325-mesh with infrasizer giving about 90 per cent of the latter) averages about 525 tons per day. A brief description of each unit will be given and comments will also be made relating to operation. This will be followed by certain test data from which, in conclusion, operating results are summarized.

Jan 1, 1938

By H. Takamoto, M. Ichinose

"The basic objectives of mine roadways are to provide sufficient cross sections in order to meet the needs of accommodation of equipment, transport, personnel travel and ventilation. However, many roadways become damaged to the extent of needing maintenance, generally dinting, and in some cases requiring re-ripping. The damaging of a roadway is a result of several factors including geological properties of surrounding strata, method of roadway formation, support systems and so on. Among these factors, strata conditions play important effects on the stability of roadways and other mining activities. Weak rocks cause excessive roadway closures, and water softens some rocks and worsens the closure problem. In Indonesia, over 250 Mt of coal is now produced from almost surface mines. In the near future, some coal must be mined from underground. Unfortunately, the mechanical properties of coal measures rocks are not so good to open underground mines. In this paper, a scientific discussion on the effect of water on the stability of roadways is given on the basis of results obtained by means of in-situ investigation and laboratory tests both in Japan and Indonesia."

Jan 1, 2011

By Peter L. Sheehan, David A. Fawcett, Dennis C. Martin

"Smoky River Coal Limited has successfully completed a major program involving the pattern rock anchoring of a high, steeply dipping footwall slope. The slope dips at approximately 65 to 70 degrees to the north, is benched for the upper 200 feet, is supported with rock anchors for another 240feet, and is unsupported at the pit bottom. In addition to the height and steepness, several structural features including shears, rolls and stratigraphic pinch- outs complicate footwall stability.This paper presents an overview of the project with descriptions of the engineering geology and footwall design, anchor installation, instrumentation and monitoring and a cost summary.IntroductionSmoky River Coal's mines are located in the foothills of the Rocky Mountains near Grande Cache, Alberta, approximately 200 miles west of Edmonton. The Smoky River coal leases were initially developed in the late 1960s and, except for minor shutdowns, have been in continuous operation since 1969 producing a low volatile metallurgical coal, mainly for the export market. Initial coal production was from underground mines; sur face mining started in 1971, and a large surface mine, No.9 Mine, was opened in 1974. Since that time, a number of open pits have been mined within the No.9 Mine area. Surface mining is by conventional shovel-truck method s with the use of a backhoe for mining the narrow pit bottoms.Coal recovery is mainly from the No.4 seam, which has a typical unstructured thickness of 20 feet. The most attractive opportunities for open-pit mining exist in areas of over thickening of the coal seam in the hinge zones of synclines and anticlines and in dip-slope situations. The mining of the more structurally complex pits and steeply-dipping footwall slopes requires that consideration be given to footwall stability."

Jan 1, 1988

By J. J. Pfeiffer, J. W. Myers, A. A. Orning

A study was made of the feasibility of using washery refuse in the manufacture of lightweight aggregate for building materials . Preliminary caking and burning tests showed that the refuse could be converted into lightweight aggregate but that refuse passing a No. 14 U.S. Standard screen could not be used without additional processing . The aggregate was prepared by pelletizing the refuse and burning out the carbonaceous material on a chain- grate in a refractory - lined furnace . A small stationary - grate furnace was used to study the process variables involved and establish optimum ignition and combustion conditions . Maximum ignition rates were obtained at air rates of approximately 200 lb per sq ft hr , but air rates of 450 or higher were required in the burnout period to obtain temperatures high enough to sinter the ash . The data obtained from this unit were used as a guide in the operation of the chain- grate furnace . In the chain - grate furnace , satisfactory results were obtained by using primary air rates of 200 lb per sq ft hr in the ignition zone and 500 lb per sq ft hr in the burnout zone . The ignition- zone air was preheated to 500 ° F , but the air for burnout was not preheated . A total of 2-1/2 tons of aggregate was prepared in this unit and made into experimental block . A commercial development based upon the results of this study yielded a product which met the ASTM specifications C 130-42 for lightweight aggregate , and blocks made from the aggregate were of good color , durable , and light - inweight .

Jan 1, 1964