Search Documents

By H J. Stedman

A Transient Electromagnetic (TEM) geophysical survey was trialled in Bowen Basin Permian coal measures overprinted by Cretaceous intrusion. The trial’s intention was to compare whether TEM could assess residual coal more accurately and economically than drilling.TEM results were promising but had limitations. TEM did not compare to drilling for defining coal thickness or relative level definition. However, TEM resolved conductive anomalies laterally; providing a qualitative picture of remnant coal.Three material types and associated conductivities occur within the trial area: overburden (sandstone/siltstone), intrusive sills and heat affected coal.Ground conductivity was analysed by measuring decay of residual current within the TEM loop. Fast decay related to resistive overburden and intrusion, attenuated decay related to conductive coal.Generally speaking, carbon content governs coal resistivity where good quality, low ash, bright coal is more resistive relative to dull, high ash coal. Though in the trial area, relative to intrusion and overburden, coal was found to be the most conductive of the three materials.By modelling conductive anomalies, a general picture emerged of remnant coal regions. Subsequent highwall exposure reconciled with conductive TEM anomalies.CITATION:Stedman, H J, 2017. Findings from a transient electromagnetic trial for heat-affected coal, in Proceedings Tenth International Mining Geology Conference 2017, pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By L. R. Stark

Two wetland simulation experiments were carried out in order to determine the effects on manganese retention of several wetland design parameters, including flow rate, inlet pH, carbon supplementation, substrate type, and surface free water depth. The primary aim in each experiment was to determine if sustained manganese retention could be accomplished under the specific experimental treatments. If successful, these experiments could recommend design parameters for the construction of field wetland systems for manganese treatment. Crushed limestone clearly was superior to spent mushroom compost with respect to manganese retention. The presence of free surface water detracted from manganese treatment, while lower flow rates enhanced manganese treatment. Sustained manganese retention was achieved using crushed limestone as the substrate coupled with an absence of surface free water, under inlet water conditions of pH 7.0 and no appreciable iron. Sustained manganese retention was not achieved under reducing conditions using spent mushroom compost while varying flow rate, inlet pH, and carbon supplementation regimes. However, lowering the flow rate resulted in many significant beneficial effects on outlet water chemistry: lower outlet manganese concentrations (over the short term), higher outlet pH, lower outlet acidity, higher outlet alkalinity, higher outlet sulfide, lower outlet sulfate, and lower outlet redox potential. Supplementation of the wetlands with dairy whey resulted in lower outlet manganese concentrations (over the short term), marginally higher outlet sulfide levels, and acted to lower the redox potential under the high flow regime. Wetlands receiving a neutral pH had lower outlet acidity, higher outlet alkalinity, lower outlet sulfate, but equivalent outlet manganese concentrations than wetlands receiving an acidic pH. When manganese is the primary mine water contaminant and a passive water treatment system is to be used, it is recommended that crushed limestone with negligible surface water be used in place of composted materials. This recommendation assumes a source water with circumneutral pH and an absence of other metals.

Jan 1, 1993

By H. A. D. Kirsten

Shotcrete has become a strategic component of support in underground mines. The ductility of reinforced shotcrete makes it a safe and economic means of surface support under adverse static and dynamic loads. The ability of ductile shotcrete to sustain load at large deflections enables excavations in squeezing conditions to be stabilized and the safety in excavations subject to rock bursting, to be assured. A Shotcrete Working Group was formed to find the configurations of fibre reinforcement that would give shotcrete the same ductility as when reinforced with mesh. Beams and panels reinforced with various types and lengths of fibre were accordingly tested. A single mix design consisting of river sand, ordinary Portland cement, fly ash, condensed silica fume and gunite dust and segregation suppressant was used. Steel and polypropylene fibre varying in length from 25 to 50 mm were used in nominal contents of 5 % and 0.5% by mass respectively. Beams, panels and control specimens were shot into specially made formers. Suitable mixing procedures were developed for the different types of fibre. The test specimens were shot in a semi-dry mix process. The shotcrete was cured until tested 28 days after shooting. The fibre contents and uniaxial compressive and Brazilian tensile strengths of the shotcrete were determined from the control specimens. The beams and panels were tested in bending in specially manufactured test rigs. The beams were examined for simple supports and fixed ends. The panels were fixed in a manner that simulated underground conditions and were loaded statically under uniform pressure. The beams were loaded and the corresponding deflections measured up to failure. The panels were loaded up to mid-span deflections of 150 mm. The results are presented in the form of load-deflection graphs. The peak loads and ultimate deflections for the fixed end beams were considerably larger than for the simply supported beams for the various types of fibre considered. None of the beams tested, however, were able to sustain load at relatively constant value beyond the peak load. The panel tests showed that 40 mm and 50 mm long steel fibre and 30 mm, 40 mm and 50 mm long monofilament polypropylene fibre reinforcement gave shotcrete the same ductility as mesh.

Jan 1, 1998

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, Mexico, 150 km (95 miles) southwest of Ciudad Juarez (Fig.1). The ore deposit was discovered in 1979 and was placed in production in 1992. The production rate is about 2.4 kt/d (2650 stpd) from an ore reserve of 8.5 Mt (9.3 million st). Grades currently average about 8% zinc, 0.5% lead, 0.2% copper and 50 g/t (1.46 oz/st) silver. Substantial inflows of water into the underground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark is a joint venture with 90% participation by Minas Penoles, SA de CR of Mexico City and 10% participation by Promociones Industriales Banamex, S A de C V (PIB S A) of Mexico City. Anew company, Minera Bismark, SA de CV was formed to operate the property. Cyprus Minerals was a 40% participant in the joint venture but, in early 1993, sold its share to Minas Penoles. The Bismark Mine is one of the largest new underground mining projects built in Mexico during the last 10 years. It is the country's fifth largest underground metal mine and provides about 1 % of the world's zinc supply at about 50 t/a (55,000 stpy). Bismark is a trackless operation with overall productivities of 7.6 t/manshift (8.4 st/manshift). The 2.4-kt/d (2650-stpd) concentrator started up in March 1992.

Jan 1, 1994

As it is probable that a large proportion of the members of the Institute attending this meeting are connected with the metalliferous side of mining, the writer thought that, as coal and coke are required for various purposes in considerable quantities by their companies, some particulars of the coal industry might be of interest, especially when visiting such an important coal-mining centre as Newcastle. It is proposed to deal with the matter from the mining and economic point of view, as the geology has been so well and exhaustively dealt with in various publications referred to in the bibliography at the end of this paper. In the immediate vicinity of the city of Newcastle the collieries are gradually being abandoned, and during the past few years the Wickham and Bullock Island, Stockton, Hetton, Newcastle Coal Mining Company's "B," and the Australian Agricultural Co's Sea pit, have disappeared from the coal-producing list of collieries. AIl of these collieries worked the Borehole seam, from which, up to date, the largest quantity of coal has been produced in the northern district.It is the bottom seam of any present commercial value in the Upper or Newcastle coal-measures, and although the coal-in this seam has not been entirely 'exhausted in the collieries referred to, they have been abandoned for various reasons. For example, although about 60% of the seam (18 to 20 ft. thick) was left in the workings in the form of rectangular pillars under the city of Newcastle, this was not sufficient to 1?revent'the subsidence which took place about twelve years ago.Again, large quantities of coal in the Borehole seam have been left to protect the shipping arrangements at the Dyke, and other...

Jan 1, 1918

By X. S. Tan

This paper deals with the analysis of stress condition on the interface between two types of floor rock materials when the vertical stress is larger, or when the horizontal stress is larger in a rectangular opening. It indicates that the floor Failure and the failure stress of floor rocks are closely related. It also demonstrates that a larger horizontal stress is one of the most important factors in increasing the potential for floor rock failure and floor heave.

Jan 1, 1990

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

As manufacturers and mine operators develop and implement proximity detection systems (PDSs), they need to be mindful of the systems’ compatibility with mineworkers’ tasks, and possible unintended consequences. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed mineworkers at mine sites that currently use or previously have used PDSs on mobile equipment, including shuttle cars, battery haulers and scoops. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure and risk. Mineworkers also suggested that improved system task compatibility, training, logistics and PDS performance might help address these issues. Manufacturers and mine operators implementing this or similar technologies may also consider mitigating task incompatibilities up front, performing additional site-specific usability testing and restricting the use cases of the system to improve performance.

By C S. Szentesy, K Howie

The Rosia Montana gold deposit is located within the æGolden QuadrilateralÆ area in the Apuseni Mountains of Transylvania, Romania. The deposit is situated approximately 85 kilometres north of the regional centre of Deva, within the province of Alba, at elevations of up to 1100 metres above sea level. The Rosia Montana deposit contains a current resource of 344.07 million tonnes at an average grade of 1.3 grams per tonne (g/t) gold (Au) and 6.0 g/t silver (Ag) for a total (measured, indicated and inferred) contained resource of 14.29 million ounces of gold and 67.00 million ounces of silver. The resource was calculated using a 0.6g/t Au cut-off, a 10 x 10 x 10 metre block size and multiple indicator kriging. The low sulfidation style epithermal mineralisation at Rosia Montana is hosted within Tertiary age dacite intrusions and related vent breccias. Mineralisation is generally disseminated and associated with silica, adularia, illite, pyrite and carbonate alteration of host rocks, with minor late carbonate-base metal veins. Precipitation of precious metals is generally considered to have occurred as a result of over-pressurization, boiling and subsequent brecciation. The dacite intrusions are hosted in Cretaceous shallow marine and deltaic shales and slates, which overlie older Paleozoic sedimentary and metamorphic rocks within uplifted sections of oceanic sea floor.

Jan 1, 2002

By P. A. Mahanwar

Flyash were melt mixed with nylon 6 at a 30wt% concentration. TYZOR® TPT, a coupling agent, was used to facilitate the link between filler and matrix. The morphological characterization, using SEM, revealed sufficient matrix residue on the filler surfaces thus confirming the strong interfacial bonding between the filler and the matrix on treating. Tensile, impact and the flexural properties of the composites were also improved with the incorporation of coupling agent. As flyash particles tend to impart a grayish color to the plastic, TiO2 pigment was employed to make the formulations aesthetic. The pigment was added to the filled system in 0.1, 0.5, 1.0, 1.5, 2.0 wt/wt ratios. Scattering of incident light and spectral reflectance was higher for smaller particle size flyash. Moreover an increase in the scattering with increase in pigment concentration indicates better dispersion of the pigment, which again is due to the presence of coupling agent.

Jan 1, 2006

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

Equipment-washing facilities at Freeport-McMo-Ran?s Sierrita Mine in Arizona produce a mixture of oil and water that was difficult to dispose of easily or cheaply. However, after some changes in the facility, waste oil is now used as part of the mining process. Freeport-McMoRan Copper & Gold Inc., head-quartered in Phoenix, AZ, operates copper, gold and molybdenum mines. It is the world?s largest producer of molybdenum. Heavy equipment used at the mine is hosed off periodically in the wash bay. The dirty water and oil mixture drains into the sump next to the bay. Oil was manually collected for disposal. This was a tedious and dirty process Mine managers sought a more efficient method of removing the oil. Instead of spending the time and effort skimming the tank with vacuums or sorbents, they enlisted the help of Abanaki Corp., manufacturer of the Model 4 Oil Grabber. Engineers designed the sump to utilize prevailing winds to blow the oil to one corner. This was the ideal place for the Abanaki skimmer. The skimmer removes the oil and discharges it into a plastic storage container. ?This reduces the time needed to keep the area clean, and the staff can focus on cleaning the equipment rather than worrying about the oil,? according to Jay Salerno, construction manager at the Sierrita Mine. Salerno is considering adding an optional oil concentrator to the skimmer to make the process even more efficient. The concentrator would remove any water picked up by the belt and return it to the sump, leaving nearly pure oil for disposal. Because the mine is located in the Sonoran desert, most of the water evaporates in the hot, dry air and is not reused.

Jan 1, 2009

By Arndt C. R

The Ispat Mexicana SA de CV (IMEXSA) pelletising plant is located at Lazaro Cardenas on the west coast of Mexico. It is the primary source of feed stock for the adjacent direct reduction (DR) plants and steelmaking facilities. The initial design of the pellet plant began in 1981 for 3 Mtpa of DR grade pellets using local concentrate received by pipeline.' Several construction delays, an ownership change, and a decision to use imported concentrates delivered in 60 000 to 90 000 tonnes ship cargoes required flowsheet modifications and additions. The design concepts are described for the plant which includes concentrate regrind to final pelletising particle size.

Jan 1, 1999

By Misra V. N, Cheng C. Y

Two types of Mt Tom Price hematite iron ore from Hamersley Iron P/L were tested using a Humboldt Wedag Jones P40 wet high intensity magnetic separator (WHIMS). The parameters tested were magnetic intensity (7000, 9000 and 11 000 Gauss), groove plate type (8R and 12R) and gap width (2.5 and 1.8 mm). It was found that at 9000 gauss magnetic intensity, reasonably high-grade and recovery in the concentrate were obtained. At 2.5 mm plate gap width, the 12R groove plate performed slightly better than the 8R groove plate. Further testwork is recommended to optimise the magnetic intensity, feed flowrate and pulp density, wash water pressure and flowrate with 12R and 8R groove plates at 2.5 mm gap width.

Jan 1, 1999

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

By L. C. Graton, Joseph Murdoch

I. Introduction......................... 26 1. The Relations of Scale in Geologic Work........ 26 2. General Characteristics of Copper Sulphide Ores..... 29 3. Scope of Present Study................. 31 11. Description of the Important Minerals............ 36 1. Pyrite....................... 36 2. Pyrrhotite....................... 41 3. Chalcopyrite...................... 41 4. Bornite........................ 40 5. Covellite....................... 50 6. Chalcocite....................... 52 7. Enargite...................... 59 8. Tetrahedrite and Tennantite.............. 61 III. Conclusions.......................... 62 I. Introduction. The Relations of Scale in Geologic Work. Many features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly 011 this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.' Thus, a mural

Jan 1, 1914

By Lian-Jin Tao

With fast development of China modernization, road construction obtains great achievement. However, in the construction process of highway, especially the high-grade highway in mountainous area, there are many unavoidable high cut slopes. Specifications for Design of Highway Subgrades, China, prescribe that the design scheme of slope with height more than 30m should be compared with bridge scheme and tunnel scheme economically. In spite of the existing guidelines, it is still quite common to see many high slopes due to engineering geological conditions, highway line shape, cost and issues related to traditional design ideas. Actually the traditional way with ?high backfill, the high cut? for mountainous highways seriously damages the original ecological environment and groundwater system, especially to those area with weak ecology, where the damage is unrecoverable. It is quite common practice to use artificial vegetation for cut slope virescence, however it still has problems such as low ratio of survivor, high maintenance cost and lack of species diversity. Now people are more and more aware of the importance of ecological environment, it becomes urgent to decrease the damage to ecological environment after ensuring the stability of high slopes. With the aim to reduce ecological damage, we proposed a new design approach which is ecological environment friendly by decreasing cut slope height with steep excavation scheme. This approach requires that (1) the geological condition is good, and the rockmass can be sTable itself; (2) excavation should not badly damage the rock, which means blasting must be controled by using buffer blasting, smooth blasting and pre-splitting blasting; (3) if local geological condition is not very good, excavation should have intervals for one bench, the advised space is 20m; (4) to ensure the slope stability in construction process, the cut slope should be reinforced more strongly than usual and in time. Finally, the deformation of the slope and the working condition of the reinforcement structure should be monitored to ensure the slope stability. The new design is used to a roadside cut slope of provincial trunk highway S223 in Guangdong Province. Based on intensive geological investigation and borehole tests, it is found that the slope rock mass is intact and sound, and the rock strength is quite high. Results from numerical modeling by UDEC reveal that compared with the traditional design scheme with 90.23m high slope, the steep scheme with only 23.46m high is characterized by its relatively large deformation and stress concentration, however the influenced area only appears at the upper slope and tends to sTable. With cable reinforcement, the stability of slope excavated steeply can be guaranteed. Deformation of the slope and the cable force are monitored in details in the period of construction, which show that the deformation of the slope decreases gradually and the final deformation is very small, and the cable tensions change small after the cables were tensioned. It is optimistically estimated that the steep slope should be sTable during operation. Comparison analysis between the steep scheme and the common scheme affirms that the steep excavation is better than the traditional scheme in terms of ecological environmental effect, slope height, the excavated amount, the excavated quantity of slope surface, engineering cost. It is concluded that if geological condition permits, the steep cut scheme should be used with better benefits.

May 1, 2009

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966

Promoters for Soap Flotation of Phosphate Minerals

Sep 13, 2010

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974