Search Documents

By Earle E. Schumacher, Alexander G. Souden

IN the field of physical metallurgy it is becoming increasingly difficult to keep abreast of the recent develop¬ments since the diversity of investigations is so great and the literature so voluminous. The purpose of this review is to present the more important advances in the nonferrous field during the past few years, the topics discussed being classified broadly as fundamental and practical. The former includes those studies that have done most toward developing the basic science of metals and alloys, and the latter includes technical developments and applications. With the rapid growth of the metal

Jan 1, 1938

By Alla D. Mah

Titanium forms several compounds with oxygen and also is able to dissolve interstitially about 33 atomic percent of oxygen. Starting with titanium dioxide, reduction becomes increasingly difficult as oxygen is removed; and the final step, be reduction of the titanium-oxygen interstitial solutions, is by far the most difficult. The possibility of reducing titanium oxide, or of purifying titanium containing oxygen, by treatment with certain more volatile metals has been a subject of considerable interest. Theoretical appraisal of the limitations of this possibility, however, has been hampered by lack of adequate information on the thermodynamic properties of the titanium-oxygen solutions. The purpose of the present work was to remedy this difficulty by expanding the thermodynamic knowledge regarding these solutions. The experimental work involved three types of calorimetry and furnished the following information: (1) Heats of formation of 11 titanium-oxygen solutions, in the range of 0 to 10 wt.-percent oxygen, were determined at 298.15° K. As a byproduct, an improved value of the heat of formation of rutile was obtained, which, in turn, led to improved values of the heats of formation of the lower titanium-oxygen compounds. (2) Low-temperature heat-capacity data and entropies at 298.15°K in were determined for 2 representative titanium-oxygen interstitial solutions. (3) High-temperature heat-content data were obtained for 2 titanium-oxygen interstitial solutions to about 1,600° K.

Jan 1, 1957

Some major mineral deposits in northern Australia are found in preconsolidation slump disturbances in the sediments.In the retransported marine sediments at Tennant Creek, breccia beds and disturbances are found which have localized later mineral deposits such as the Peko copper orebody. These disturbances are thought to result from slumping, turbidity flow and various types of "semi-fluidized" subaqueous slides intermediate between slumps and turbidity currents.Movements are found to ~ause widespread disturbances in the sediments such that subsequent mineralization can spread through a large volume of rock giving rise to orebodies greater than those localized by tectonic structures.A similarity is noted between the sedimentary disturbances at Tennant. Creek and those at Mount Isa and Mary Kathleerr. It is suggested that disturbed beds which are host rocks to ore minerals in these mines may also be due to movements of the sediments before compaction.Certain characteristics of the slumped rocks can be recognized and limited generalizations can be made about the shape, extent and habit of these host rocks and the orebodies they contain.INTRODUCTIONSubmarine slumping and· turbidity current retransport are almost entirely responsible for some types of deep marine sediments.However, little attention has yet been drawn to slump deposits and associated disturbances bedded in the sediments as features localizing later mineralization.A study. has been made by the writer of the slump and associated phenomena of the ,Tennant Creek field where many mineralized bodies, including some gold and copper orebodies, occur as replacements of coarse fragmental slump...

Jan 1, 1960

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By B. Genc

After the explosion at Middelbult Colliery, South Africa in May1993, which claimed 53 lives, the South African Coal Mining Industry and the Safety In Mines Research Advisory Committee (SIMRAC) united forces to establish a surface facility to develop and test on-board flame suppression systems for continuous miners and roadheaders. The first test that was conducted in this newly constructed test tunnel at the Kloppersbos Research Facility, CSIR was in July 1995.Since then 70 tests have been conducted using the facility and have focused on on-board active ignition suppression systems for continuous miners (CM) and road heading (RH) machines to enhance the safety of South African mine workers in collieries. These suppression systems are mounted on the CM or RH machine and detect the occurrence of an ignition by means of light-sensitive sensors. The electronic signal from the sensor triggers the suppression system, creating a flame-suppression curtain, containing and extinguishing the flame in the immediate vicinity of the ignition. Forty-three tests have been conducted with an active on-board suppression system present inside the test tunnel. Since flame propagation speed is an extremely important parameter, the CSIR-Miningtek made the results of the test programme available for re-analysis. Flame speed depended on whether a machine was present in the heading or not, the geometry of the heading and the volume and composition of the explosive mixture of gas. Flame speeds of up to 190 m/s were recorded. However, the active suppression systems were almost always successful in containing flame propagation.

Jan 1, 2002

Outsourcing of specialist and non-continuous services is common practice in international mining operations. There is an increasing trend towards this practice in South Africa as a result of the major organisational changes that have taken place in the industry, and as lower revenues and production cost pressures have reduced profit margins. Many specialist functions have been outsourced in the industry for a long time, an example being shaft sinking, which is undertaken by specialist shaft sinking contractors. In the professional services area, some activities have been outsourced, for example the design and construction supervision of tailings dams, but mining related activities such as geology, mine planning and scheduling, engineering, ventilation, and rock engineering, have traditionally been carried out by in-house staff. In this paper some of the industry problems which have led to an increase in outsourcing of professional services are considered. Then the pros and cons of outsourcing are dealt with before outlining the factors which should be taken into account in choosing an outsourcing partner.

Jan 1, 1999

By Daniele Tolazzi

Electric Arc Furnaces keep evolving into highly powerful melting units, shrinking taptotap times by increasing the effectiveness of the energy sources and the material fluxes used in the process. Steelmakers are targeting to increase the efficiency of their injection package in order to reduce the overall conversion costs, seeking for technologies specifically designed to promote the metallurgical reactions in a predictable and reproducible process automatically controlled at the correct timing. Many technological enhancements have focused in the gas management, improving the burner design and the penetration capacity of oxygen injectors, dedicated to decarburization and the other exothermic reactions. Instead, lower evolution efforts have been addressed to engineered solutions for managing the addition of solid materials required in slag forming, although they are playing a key role in EAF process optimization, as well. The paper describes the latest solutions designed to manage efficiently the injection of fuel, oxygen and powdered materials in several EAFs and presents the operational results achieved. Accurate control of reliable additions of coal, lime and magnesia proved crucial for the control of the slag FeO and viscosity, generating stable foamy slag and producing cleaner steel.

Aug 17, 2017

By Bruce I. Thomas

[THIS PAPER, tine of a series on placer ml n in iii Alaska, describes mining methods and gives unit costs at operations where hydraulic and mechanical excavation equipment is used with nonfloating washing plants. The mining methods described were developed during the last 30 years to copy with conditions peculiar to arctic and subarctic regions arid are now used by a large segment of the placer mining industry in Alaska. The operations described have been classified if m ii into three main categories: Those having sluices at a bedrock level, those having sluices above bedrock and those having mobile nonfloating washing plants (dryland dredges). Diesel-powered bulldozers and draglines convey or clevate gold-bearing gravel to the sluices, remove tailings, and strip waste gravel and other overburden. Diesel-powered centrifugal pumps supply water foe sluicing and hydraulic stripping. Detailed descriptions and unit cost arc presented for 14 operations to illustrate the numerous arrangements udder the first 2 categories.]

Jan 1, 1959

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931, The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results off other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time Each sample was taken will also be retorted. History of Survey The Bureau of Mines made its first survey of motor gasolines sold throughout the United States in 1915,4 a second in 1917,0 and a third in April, 1919.0 These three surveys showed that during each 2-year interval the motor gasoline had become notably less volatile. In order

Jan 1, 1932

By C. Ogasawara

This document describes the direction and progress of the Bureau of Mines Oil Shale Mining Environmental Research Program as of January 31, 1979. It is aimed at focusing the Bureau's role in environmental research supporting oil shale development with respect to the activities of other involved government agencies and private industry. Environmental considerations in oil shale extraction, such as ecological disturbances, health and safety hazards, waste management, and socioeconomic impacts, are discussed along with the type of research known to be planned by organizations to ameliorate these problems.

Jan 1, 1979

By H. F. Niemand, C. J. Postma, P. L. Crouse

"SynopsisThe separation of zirconium and hafnium is essential in the nuclear industry, since zirconium alloys for this application require hafnium concentrations of less than 100 ppm. The separation is, however, very difficult due to the numerous similarities in the chemical and physical properties of these two elements.Traditional methods for separation of zirconium and hafnium rely predominantly on wet chemical techniques, e.g. solvent extraction. In contrast to the traditional aqueous chloride systems, the AMI zirconium metal process developed by Necsa focuses on dry fluoride-based processes. Dry processes have the advantage of producing much less hazardous chemical waste.In the proposed AMI process, separation is effected by selective sublimation of the two tetrafluorides in an inert atmosphere under controlled conditions, and subsequent selective desublimation. Estimates are made for the sublimation rates of the two tetrafluorides based on the equilibrium vapour pressures. A sublimation model, based on the sublimation rates, was developed to determine if the concept of separation by sublimation and subsequent desublimation is theoretically possible.IntroductionZirconium requires several purification steps to conform to nuclear-grade specifications. Little information is available on the sublimation separation of Zr and Hf compounds, especially in the fluoride form, the majority of which deals with sublimation under vacuum conditions. On the industrial scale, only vacuum sublimation of ZrF4 has been reported. No records were found for the sublimation of ZrF4 in an inert atmosphere. Information on the sublimation rate of ZrF4 or HfF4 in an inert atmosphere is also limited. The rate is assumed to be dependent on several factors, of which temperature, area, and composition are considered the most important."

Jan 1, 2015

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By A. H. Swart

Rock engineering is concerned with the design of rock structures generated by mining activities. Therefore, rock engineering designs have major implications for the safe recovery of mineral deposits and operating costs. The paper deals with a few challenges facing rock mechanics engineers operating in the hard rock underground mining environment in South Africa. Finally, examples are included, which may assist rock mechanics engineers in providing better designs, which could ultimately lead to further improvement in safety and lower operating costs.

Jan 1, 2005

By J. C. Boswell, J. D. Crawford

IN addition to its base-metal and coal mining operations, the United States Smelting Refining and Mining Company has, for the past quarter century, been one of the few large American mining companies interested in dredging. Its activities in this field are confined to gold, and to Alaska, but it is the largest operator in that territory, with twelve huge dredges available to work during the summer on the frozen ancient beach sands at Nome and the gravels of Fairbanks. These operations will be described separately.

Jan 1, 1948

By W. C. Goldberg, E. M. Frizzell

Monitoring slope displacement in open-pit mines can help predict collapses and prevent serious damage, injuries, and fatalities. Early detection of movement may indicate the need to modify slope geometry, initiate dewatering if the slope is wet, or consider artificial support measures such as cable bolting. Slope monitoring at the Berkeley pit was carried out with varying degrees of intensity and continuity for about 15 years. Some of the old mine records are still intact and accessible. Slope monitoring data can therefore be collected and published for the benefit of other mine operators. Because prediction of slope failures is empirical in nature, publication of several well documented case studies will be a valuable contribution to the industry. Background - Berkeley pit Open-pit mining of copper from the Berkeley pit, located on the east side of Butte, MT, began in 1955 and ceased in 1982. During that time, about 1 Gt (1.2 billion st) of material were removed to form a pit about 1.8 km wide by 2.1 km long (6000 ft by 7000 ft) at the rim, and 550 m (1800 ft) deep as measured from the high hill on the northwest side. From the south side, the pit only measures 365 m (1200 ft) deep. The Berkeley pit was first owned and operated by Anaconda Minerals Co., and subsequently by Arco. Following its closure in April 1982, the mine began to fill with water. Washington Construction purchased the property in 1986, and Montana Resources Inc. began mining to the east of the Berkeley pit in July 1986. Numerous instances of slope failure were recorded during the course of mining and several intensive geotechnical investigations were conducted in an effort to optimize the mine design. One of the last and most comprehensive studies was initiated in 1977. For purposes of geotechnical analysis, the mine was divided into nine design sectors on the basis of geologic conditions, geographic orientation, and economic importance (Fig. 1). Only two of these sectors - the concentrator and the southeast corner - are considered here. Material properties were obtained from several studies of samples collected from the mine and adjacent areas. The slope was monitored using standard surveying techniques to record the amount of movement in an area. The

Jan 1, 1989

By P. Sanchez-Mejorada

GEOLOGISTS who are acquainted with the mines of northeastern Mexico realize that the most important lead-silver replacement deposits of the province are confined to a single formation. But since the formation is several hundred meters thick, the author has determined the relative position of the lead mantos in the belief that this information will prove useful in the search for new mines. This article describes the stratigraphic location of lead-silver replacement deposits known in several mines situated in a region comprising part of the states of Coahuila and Nuevo Leon. The area studied extends for 200 km* (125 miles) from east to west and 70 km (45 miles) north to south. Metallogenic Province: The most important metallic deposits of the region have the following common characteristics: 1) The orebodies occur as manto replacements of calcareous sediments. 2) The horizons that have contributed large tonnages of ore are in similar positions in the corresponding stratigraphic columns (as it will be shown later on). 3) Lead is the most important metal in the ores. Silver is commonly present in small amounts. Occurrence of zinc is dependent on the degree of oxidation of the primary sulfides. 4) A large proportion of the total production has been in the form of oxidized ores. 5) The deposits are located on anticlines. Rocks of Cretaceous age crop out over large areas of the states of Nuevo Leon and Coahuila. forming part of a belt that extends to the south along the eastern Sierra Madre. The sediments are cut by a small number of intrusive stocks ranging in characteristics from rhyolite to diorite. The most prominent structural feature of the region is a series of folds trending northwest-southeast. Faulting is not conspicuous in the region, although a major fault zone is found farther East.' The physiography closely reflects structural features, with mountains formed by anticlines and valleys conforming with intermediate synclines. Narrow valleys have also been developed along the axes of many anticlines, where solution of limy sedi- ments and erosion have proceeded along axial tension fractures. Stratigraphy: Rocks of the Upper Cretaceous are exposed in only a small percentage of the total area. Generally they have been eroded away from the mountains and are covered by recent talus and alluvium in the valleys. Humphrey' has published an excellent paper describing the Cretaceous formations of the Sierra de los Muertos, a short distance west of Monterrey. A brief summary of these formations is given below to convey an overall picture of the stratigraphic sequence that prevails just south of the area under consideration. Upper Cretaceous Indidura: Essentially thin shaly sediments. Cuesta del Cura: Limestone in thin wavy beds

Jan 1, 1959

By Peter Moser, A. Gaich, E. Grasedieck Zechmann

In The SMX Blast Controller is a novel tool for precisely controlling the geometry of a blast based on the technology of 3D imaging. It enables to derive precise information about the geometry of the face of a bench in a quarry from a pair of stereoscopic images taken from the bottom level of a bench with a calibrated standard digital camera. Apart from staking out the blast position with delimiters that mark the area to blast and taking then two images (freely), no further actions are required which allows performing the data acquisition without requiring any surveying skills. The 3D image generation and blast planning does not require special computer. It is estimated, that every blast foremen is able to work with the system after a one-day training as the system includes a high grade on automatism. The software package allows the blast foreman to design and stake out a blast, based on provided geometric values, such as burden, side spacing, hole inclination, sub-drilling, row number & distance and drilling pattern. The software connects these values with the 3D information acquired by the digital images. All the drill & blast information can be used also for blast documentation. The SMX Blast Controller overcomes also the problem of doing the back transfer from maps derived by surveying into nature as the resulting 3D image and all the information associated to it (hole position, etc.) can be correlated with the nature by visual comparison and the help of a single reference line, defined by two points. The system is designed to be used also in small to medium quarries. It can help, that the control of the geometry of the bench face and the precise design of the charge of the blast on a borehole per borehole basis will become an accepted daily routine.

Jan 1, 2006

By P J. Minehan

The investigation of the potential of the Webb/Baynes block of the Buller coalfield for anode carbon manufacture has generated much information on the physical beneficiation characteristics of the Buller coals in general. A further 36 drill holes of the block in question and several other samples have been analysed by sink/float analysis, either at a single density or over a range of densities. In addition, many samples have been beneficiated on a laboratory shaking table or by flotation. The ash content can be reduced by a variable factor. The reduction factor of between two and four by sink/float analysts is understandably less for tabling where separation is not perfect. All Buller coals behave similarly, there being greater ash reduction factors for higher ash coals.

Jan 1, 1983

By Rodney L. Stone, David S. Cahn

As part of an over-all laboratory and plant test program to determine mixing ad other techniques for a more economic use of bentonite as an iron ore pellet binder, a settling test for measuring the bentonite content within a pellet or a batch of pellets has been developed. Through this test, it has been shown that dry fracture load is directly proportional to bentonite content in batches of pellets, but inversely propor tional to bentonite content in individual pellets of the same batch. This apparent paradox is explained by a negative correlation between a pellet's size and its bentonite content and the fact that large pellets can withstand a higher fracture load than small pellets. In past attempts to characterize green and dry iron ore pellets, the authors found large variations in the results of strength tests on closely sized pellets from the same batch.' Reasons advanced for such variations in the quality of pellets in which the binder is bentonite were the presence of internal flaws and the nonuniform distribution of the binder. Even when resulting pellet strength is good, there is still the question of whether the same strength could have been attained through a more effective use of a smaller amount of bentonite. The authors' own and other studies 2-3 have pointed out the strong dependence of pellet strength on the degree of "mixedness" of the iron ore concentrate and the bentonite binder. However, before such a relationship could serve as a guide for the development of better mixing techniques and the associated economy of

Jan 1, 1969

By Natalya. N. Ankusheva

The problems of ore-bearing palaevolcanic structures in folded belts are actual because of their high productivity in nonferrous, ferrous and noble metals ores. Now relationships of location and conditions of formation for sulfide-massive and gold-bearing deposits are investigated very well in Urals. But carboniferous sulfide-barite mineralization, for example the barite veins in Arcaimsky palaevolcano are?nt studied enough now [3-5]. The purpose of this research is the studying of mineralogy and thermobarogeochemistry of barite from the hydrothermal veins. It will allow to determine the conditions of its formation and to compare it to the similar mineralization of others ore types.

Jan 1, 2006