Search Documents

By Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and the field controls used on the shot. This point cannot be over emphasized because when the geometry is not measured and/or field controls are not properly implemented, it can often have devastating effects on the final blast results. Thus drilling accuracy, tiont row burden control, explosive confinement, energy distribution, explosive selection, timing and structural geology become critical parameters in the design of successful blasts. Understanding the actual dynamics of the blast and why certain results were achieved is the fast step in optimizing a blast design. As stated by R. Frank Chiappetta, “Of all the blast monitoring systems available today, high speed videography still remains as the best stand alone instrumentation system for blast diagnostics.” Over the past years I have analyzed hundreds of blasts using either high-speed lowcams (500 frames per second) cameras or standard digital (30 frames per second). These analyses confirm, without a doubt, that shot geometry, in combination with structural geology, is the most important factor in overall blast results. Drilling accuracy is the single most important component in efficient blasting. Having equal mass associated with an equivalent energy is the basis in which blasts are designed. When drilling inaccuracy or borehole deviation occurs, not only is the energy unevenly distributed, but the basis of all design calculations becomes invalid. Over the past several years, quarry and mining operations have employed the use of boretracking measuring devices to measure borehole deviation and hole toe locations. In cases of operations using top hammer drills, it was discovered that the amount of deviation was significant and far greater than they believed they had. Set up error, improper drilling techniques and bit wear were some of the contributing factors. Through video anaysis of boretracked blasts, blast results were directly linked to drilling ..accuracy. The comparisons here took into account blast design, energy factors and hole sequencing.

Jan 1, 2000

By S. Kouniali

Experience with knowledge-based systems for Layout planning and roadway support dimensioning is on hand in European coal mining since 1985. The systems SOUT (support choice and dimensioning, 1989), SOUT 2, PLANANK (planning of bolt-support), EXOS (layout planning diagnosis. 1994), Sout 3 (1995) have been developed in close cooperation by CdF1. INERIS2. EMN3 (France) and RAG 4, DMT5, TH - Aachen6 (Germany); ISLSP (Integrated Software for Layout and support planning) development is in progress (completion scheduled for July 1996). This new software technology in combination with conventional programming systems. numerical models and existing databases turned out to be suited for setting-up an intelligent decision aid for layout and roadway support planning. The system enhances reliability of planning and optimises the safety-to-cost ratio for ? deformation forecast for roadways in seam and surrounding rocks, consideration of the general position of the roadway in the rock mass (zones of increased pressure, position of operating and mined panels). ? support dimensioning ? yielding arches, rigid arches, porch sets, rigid rings, yielding rings and bolting / shotcreting for drifts ? yielding arches, rigid arches and porch sets for roadways in seam ? bolt support for gateroads (assessment of exclusion criteria and calculation of the bolting pattern) ? bolting of face-end zones (feasibility and safety assessment, stability guarantee).

Jan 1, 1996

By B. A. Rogers

IN addition to the usual methods of manufacturing steel, a number of special processes have been the subject of considerable experimentation-and use in manufacturing practice. A number of these methods have been of a type in which a rapid refining action has been secured through the intimate mixture of fluid slag with fluid metal. The persistence with which more rapid methods are sought is indicated by the current interest in the Aston' method for producing wrought iron and in the Perrin2 process for dephosphorizing and deoxidizing steel. In the Perrin process, in particular, the mixing action is extremely vigorous and the reactions proceed with surprising speed.

Jan 1, 1936

By Po-Ming Lin

Stress has a significant effect on the stability of pillars. In order to get an accurate picture of pillar stability, one needs information not only on the primary Stress distribution but also on all the Subsequent Stress changes as time passes. Sonic methods are some of the fastest, most economical and least destructive means of stress prediction. The wave propagation velocity has long been applied to the investigation of the upper mantle and crust stress. Recently, it has also been applied to the prediction of rock bursts and to mine site investigations. Another parameter for investigating stresses in rocks is the attenuation coefficient. Attenuation has been observed to be more sensitive to stress changes than wave velocity; however, the measurement of attenuation is more difficult than that of wave velocity. In this paper, the mechanism of sonic attenuation in rock is reviewed. Both the velocity and the attenuation of sound waves in five different rock types under various stress fields were examined in the laboratory. It was found that for a specific rock type the relationship between the velocity ratio and stress, as well as that between the attenuation coefficient ratio and stress, can be expressed by simplified second order polynomial equations.Research showed the attenuation coefficient to be more sensitive to stress change than the velocity ratio. A field investigation method was proposed using a Schmidt hammer as a repeatable energy source. Initial trials appeared to show that monitoring by the wave attenuation method gave more repeatable data than monitoring wave velocity.

Jan 1, 1984

By TENNEY C. DeSOLLAR

TRADITION tells us that the earliest use of Alabama iron was to make shoes for the horses of General Andrew Jackson and his men during the first part of the nineteenth century. The first recorded incident in the making of iron was the request of U. S. Indian Agent Benjamin Hawkins "that a crew of blacksmiths be sent to the Creek Nation in the lower Mississippi territory." These frontiersmen made up the first body of pioneer iron makers in the territory. The first known blast furnace was built by Joseph Heslip in 1818 at Russellville, named after Major William Russell, who was General Jackson's chief of scouts. The Tannehill furnace was built in 1830 in what is now Tuscaloosa County and its ruins, as shown above, can be seen today.

Jan 1, 1937

By Robert Hopler

A blast caused the destruction of a bridge and loaded freight train and the death of three men, near Chattanooga, Tenn., on May 16, 1907. The blast and its disastrous effect has been described by Mr. Hunter McDonald, M. Am. Soc. C. E., in a paper read before the Engineering Association of the South and reprinted in the Proceedings of the Association for April-June, 1907. The excessive damage was so largely due to coincidence and wreckage of the bridge and train so complete that the incident is worthy of notice.

Jan 1, 2008

By GEO M. FOWLER

AN appraisal of the activities of the mining geologists during 1936 clearly indicates the ever in- creasing utilization of geology in the search for ore. Few men with geo- logic training are idle at present; this is particularly true regarding recent graduates. Many have accepted employment in distant fields, such as the Philippines and South America, and greatly increased mineral production from these places reflects their activities. In North America, regions of intense mineralization formerly important are being restudied in greater de- tail and with better understanding; as a result, new mineral wealth is being found in many such districts. Much is being done by private companies and individuals, and it is to be hoped that mining companies will increasingly make available the purely scientific results of such studies by permitting their geologists to publish. On such generosity to a large extent will future advances in ore finding depend.

Jan 1, 1937

By David A. Andrews

Coal occurs at many scattered localities in Arizona, California, Idaho, Nevada, and Oregon, but in most of the known occurrences thick coal beds are of small extent and the coal generally contains a high percentage of impurities. The coal beds occur at many different horizons in strata of Cretaceous and Tertiary age. Bituminous coal has been found in several areas, the most extensive of which is the Eden Ridge field of Oregon. Lignite also occurs in many places, but the only extensive deposit is in the Goose Creek field of Idaho, Nevada, and "Utah. The coal reserves of the region are largely of subbituminous rank; most of the subbituminous coal is in the Black Mesa field of northeastern Arizona and the Coos Bay field of Oregon. The Black Mesa field contains more than 80 percent of the coal reserves of all ranks but is remote from both transportation facilities and centers of consumption. Substantial reserves ill the Coos Bay field are favorably situated with respect to transportation and markets. ARIZONA Subbituminous coal occurs in the Black Mesa, Pinedale, and Gallup coal fields in Apache, Navajo, and Coconino Counties, Ariz. (fig. 1). Bituminous coal occurs in the Deer Creek field in Pinal and Graham Counties and in a small area in Apache County at the north-east corner of the State. All the coal beds are in strata of Cretaceous age. The coal in the Gallup field and at the northeast corner of the State lies in the Western edge of the San Juan structural basin. "Vest and south of this basin the coal-bearing strata have been removed by erosion except in high mesas.

Jan 1, 1947

By Gene R. Reid

The contract objective is the development of an Automatic Fire Control System for Mobile Underground Metal Mining Equipment. The Phase I Report, which described the projected data handling plan, was published on July 24, 1975. The Phase II effort covered the period from July 24 through December 2 and accomplished the following objectives: ? Acquisition of data in accordance with the project data handling plan. Data were acquired through visits to twenty mine sites in ten states and Canada; visits to Bureau of Mines and MESA facilities; visits to mobile equipment manufacturers; and an extensive literature search. ? Analysis of accumulated data which provided the following specific types of design inputs: selection of the type of mobile underground equipment found to represent the greatest overall fire hazard; typical operating conditions for the vehicle; characteristics of the reported fire experiences; and performance, cost and maintenance factors affecting potential purchases of automatic fire control systems for underground mining equipment. ? Development of the AFCS design concept. Utilizing the data analysis results and considering the state-of-the-art of fire control system components, a recommended design concept was developed with particular emphasis placed on the need for a low cost and reliable system. Design trade-off studies are provided for the recommended system and for four alternate system concepts.

Jan 1, 1975

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

This Bureau of Mines report and its companion report (Information Circular 9142) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of beneficiation of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the costs for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mineral processing unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. The mineral processing handbook includes individual cost estimation sections for unit operations associated with comminution, beneficiation, solid-liquid separation, hydrometallurgy, and special applications as well as infrastructure and plant general and administrative costs. When using this system for estimating cost data for a mineral processing facility or for checking or verifying processing costs from an existing facility, a minimum amount of background information is necessary.

Jan 1, 1987

By William O. Vanderburg

This paper 3/gives the results of a reconnaissance of mining districts in Clark County, Nev., made from November 18 to December 22, 1936, and from February 9 to March 8, 1937-in all, 63 days. While the field work Was being done, virtually all of the mining districts in the county were visited and many data on active and inactive properties were obtained. The report covers the locations of the various mining districts, the nature of the deposits, information on past operations, current activity, and general data likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The principal metal-mining districts in the county are Goodsprings, Eldorado, and Searchlight. The zinc-lead ores of Goodsprings have been the most important economically, followed by the gold-silver ores of Eldorado and Searchlight. In the industrial-mineral field, gypsum, limestone, silica sand, and borates are the principal products. Metal mining in the county is characterized by numerous small operations and the ores are either milled locally or shipped to distant smelters.

Jan 1, 1937

By W. A. Vine

Next year, in 1964, Butte will celebrate its Centennial. It was in May, 1864, that the first recorded mining activity took place. During that summer, several rich placers were found on Silver Bow Creek and its tributaries, and a gold rush followed. As placer mining proceeded in the creek beds, the quartz lodes on the hillsides were located and the veins were prospected. Mining in Butte entered its second phase when the rich silver mines, the Alice, Moulton, and Lexington, were opened. The silver boom lasted until the decline in the price of silver in the early 1890's forced the closure of many of the mines. An indication of the beginning of the copper mining era in Butte was in 1866 when it was noticed that green copper carbonate discolored some of the, lode material. It was not until ten years later, however, that the Anaconda and St. Lawrence claims were located by Michael and Ed Hickey. The claims were sold in 1880 to Marcus Daly and in 1881, Daly obtained financing and organized the Anaconda Silver Mining Company to exploit the vein The silver venture was a failure because of the predominance of copper which diluted the bullion to only 400 fine.

Jan 1, 1963

By J. R. Thoenen

"The curtailment of imports of foreign potash during the World War directed attention to the necessity of establishing a domestic source of potash for fertilizer, and considerable study has been given to the subject by Government bureaus, research organizations, and private individuals. These studies have covered all known sources of potash, and among them the extensive greensand deposits of New Jersey in which the potash content is found in the mineral glauconite have been investigated.Several hundred patents have been obtained covering processes for the extraction of potash from siliceous minerals, but up to the present time none have proved successful on a large commercial scale.When the investigation of the potash deposits of Texas was started by the Federal Government, the laboratory study of the drill cores was assigned to the Nonmetallic Minerals Experiment Station at New Brunswick, New Jersey, with the object of ascertaining a possible commercial method of utilization.The purpose of this preliminary study was to investigate existing literature and previous investigations to ascertain the extent and availability of the deposits, the extent of commercial success so far attained in potash extraction, the most promising known methods and by-products obtained from them, probable markets, and possibility of competition with foreign potash, and by a study of these data to determine whether further chemical engineering analysis and laboratory investigation were warranted.As the study advanced it became evident that adequate reserves of green-sand were available for many years supply. and that whereas many processes had been patented few had been tried commercially. In collaboration with former private and Government investigators these patents were first divided into two"

Feb 1, 1929

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By S. H. Lorain

Tin mining on Seward Peninsula, Alaska, has been intermittently active since the early 1900's. Most of the recorded production (over 2,200 short tons of metallic tin) has been obtained from placer deposits, but recent production also has resulted from development of lode deposits associated with intrusive rocks occurring in the western part of the peninsula. Generally, the lode deposits containing tin minerals (principally cassiterite) are found in dikes, in granite masses, and in silicate zones in limestone overlying the granite. Both the placer and lode deposits have been of considerable strategic interest to the Government because of the almost total absence of a domestic supply of tin. The most important tin-lode deposit discovered to date is in the Cassiterite dike at the Lost River mine, on Cassiterite Creek about 85 miles northwest of Nome. This highly altered, rhyolite porphyry dike averages 12 feet in thickness, strikes N. 75° to 85° E., and dips steeply to the south; it can be traced on the surface for about 8,000 feet. Throughout its explored length of about 2,200 feet the dike everywhere contains some tin and tungsten in veinlets and disseminations; economic concentration of the are minerals, however, is confined to definite shoots. The ore minerals include cassiterite, stannite, hulsite, paigeite, wolframite, scheelite, and base-metal sulfides; gangue minerals include fluorite, boron silicates, and lithium-bearing minerals. Some ore minerals also occur in the numerous other dikes and in the granite and intruded limestone in and adjacent to the mine.

Jan 1, 1958

By Franco Oboni, Iain G. Bruce

The design of tailings containment structures relies on well-understood engineering methods being applied consistently. Unfortunately, not all facilities are designed or managed to the same level of competency. To standardize procedures, the Mining Association of Canada (MAC, 1998) prepared a “Guide to Tailings Management.” It recommended review of designs and an assessment of the risks associated with tailings impoundments be implemented during all phases of amine life. This paper describes how the quantitative risk assessment (QRA) process can be used to define risks associated with the design, construction and operation of a tailings management facility. And it discusses how, once the risk tolerability curves (RTC) are defined for a project, they can assist the risk management (RM) process.

Jan 1, 2002

By Walter W. Kaufman

The braking performance of underground, rubber-tired, coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are proposed.

Jan 1, 1977

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA), San Bernardino County, California During field work, BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1,188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) full access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion, $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990