Search Documents

By Z Chang, S A. Mrozek

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Antamina, Peru is the largest Cu-Zn skarn deposit in the world. Skarn mineralisation is focused around a multiphase Miocene intrusive complex comprising at least eight distinct phases identified by cross-cutting relationships, including truncated veins, xenoliths and chilled margins. Skarn alteration and mineralisation, as observed in drill core, remain open at depths exceeding 2.2 vertical kilometres.Porphyry intrusions occur as four major phases with subphases (from oldest to youngest): P1 (a, b), P2 (a, b), P3 (a, b) and two dykes of uncertain timing named Oscarina-1 and Oscarina-2. P1a is a hornblende-biotite quartz diorite porphyry with pervasive K-alteration, local endoskarn and 30–40 per cent sheeted quartz veins, all of which obscure original igneous textures. P1b dacite porphyry is a minor unit with <10 per cent phenocrysts and <3 per cent quartz veins. P1b cuts P1a; P2 dykes cut both units. P2a porphyritic biotite quartz monzonite contains K-feldspar megacrysts up to 4 cm long, local K-alteration and 2–80 per cent quartz stockwork veins. P2b biotite monzonite porphyry contains approximately 50 per cent phenocrysts and typically <10 per cent quartz veins. P3a (brown groundmass porphyry) and P3b (coarse phenocryst porphyry) are minor in volume and extent, and both cut P2 bodies. Oscarina dykes comprise two separate but parallel bodies. Oscarina-1 is a feldspar-phyric rhyolite porphyry, while Oscarina-2 is an intensely chloritised andesite porphyry. Oscarina-1 has a U-Pb (laser ablation inductively coupled mass spectrometry (LA-ICP-MS)) age of 10.1 ± 0.1 Ma, whereas P2 U-Pb zircon ages (LA-ICP-MS) range from 10.0 ± 0.2 Ma to 9.9 ± 0.3 Ma.All the intrusive phases contain quartz veins, with P1a and P2a having the most intensive K-alteration and most abundant quartz veins ± endoskarns. Each phase may have contributed to mineralisation at the right depths and within favourable wall rocks (ie marble) during uplift of the Antamina structural block. Therefore, a model of multiple intrusions during continuous uplift explains the vertically extensive (>2.2 km) skarn and mineralisation at Antamina.CITATION:Mrozek, S A, Chang, Z and Meinert, L D, 2015. A model for the intrusive sequence and Cu-Zn skarn formation at the Antamina deposit, Peru , in Proceedings PACRIM 2015 Congress, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M. W. BERNEWITZ

DURING my recent extended visit to Australia and New Zealand, these notes on oil and gas prospecting in that part of the world were compiled from recent reports-press and government, from conversation with one of the financial leaders in the search for oil, and from personal observation of operations of the principal importers, blenders, and distributors of oil products; also from the astonishing testimony given by them to the Petrol Commission. Australia and New Zealand have practically no petroleum production beyond a few thousand gallons a year from wells in the latter Dominion. Everything is imported, Table 1. showing the quantities for 1929-30 in Australia and for 1930 in New Zealand,

Jan 1, 1934

By Matters, R T, Coldham, Slee, J C, R J, Wallman

The Committee desires to thank the managers of the various mines along the line of lode for their hearty co-operation in its labours. It would also extend thanks to Messrs J C Moulden, Howchin, Twelvetrees, and the West Australian Geological Surveyfor various information; to Messrs J G Dreyer, S Pope, T Read, P Moncrieff, R Williams, and W J Rose for analyses; and to a number of local gentlemen for advice and help. Professor Skeats, of Melbourne University, gave much valued assistance in petrology, and Mr Herbert Lavers kindly undertook the study of the garnets.INTRODUCTIONThe famous Broken Hill lode is situated in a low range of hills, the Barrier Ranges, near the western border of New South Wales. It has been worked since 1884-fust for silver, then for silver and lead, and at present for lead, silver, and zinc...

Jan 1, 1910

By J. Dahner

Total milling cost is composed of energy, liner and grinding media costs. In primary high ball load milling, the grinding media play the biggest role in total milling cost. This cost can be drastically reduced by improving the impact condition inside the mill. The impact condition inside the mill is influenced by shell liner design (as well as feed end and discharge design) and the type of discharge. The improvement of the impact condition will result in a significant decrease in grinding media consumption. The softened impact condition allows for better alloy optimization, resulting in a further reduction in grinding media consumption. Optimized liner design can also improve energy consumption as less energy is wasted in the projection of the grinding media. Magotteaux utilizes tools to simulate and show the grinding media trajectories for shell and end liners. This paper will present some practical examples where the media and energy consumption can be or has been reduced by optimizing liner design. Keywords Comminution, grinding, liner design, grinding media wear.

Jan 1, 2011

By S. Marsland

Reference materials have always been important for validating and controlling analytical methods. They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry, demand critical validation of all results reported. Mintek has been producing geological and semi-processed ore references since the early 1970s and recently, due to increase in demand, other manufactures have entered the South African market. This paper describes analytical challenges from the customers? perspective, the customers being metallurgists, mine geologists, environmental scientists and geologists from resource companies. Reference materials with their appropriate use and a good understanding, can aid greatly in building confidence in the results, choosing the right laboratory for a project, deciding which set of results is correct and providing evidence to the customers? clients that the best possible results have been obtained

Jan 1, 2007

Case studies from four western states are used to illustrate the impact of the environmental compliance process on the mining industry. The case studies were not chosen as a statistically significant sample of all mining operations in the western United States but were chosen as representative of operations on both public and private lands and in locations that exhibited varying degrees of involvement by governmental units, non-governmental organizations and the general public. Basically, each case study was chosen because some aspect of their environmental compliance process helped to illustrate an interesting point in the regulatory process. The criteria used to select the case studies were: mines located in different jurisdictional areas, mines located in varying geological areas~ mines located in areas having different historical relationships with mining: and operations that are in production as well as those seeking an operating permit. The variety of such projects should provide the necessary foundation to evaluate the impacts of the environmental compliance process in each location.

Jan 1, 1994

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By Dhanaji S. Chavan, Thallak G. Sitharam

"It is well known that sites comprising of saturated loose sand undergoes large deformations, due to liquefaction, during seismic shaking. To cope with this, different mitigation techniques such as vibroflotation, deep dynamic compaction, compaction grouting, deep soil mixing etc. have been used in practice. However, as all these methods are costly, a new mitigation technique is required. Air injection has emerged as a new mitigation technique in which air is injected into the saturated loose sand. The introduced air makes the pore fluid mixture compressible and results into decrease in the generation of excess pore water pressure during seismic shaking. This paper reviews the laboratory and field studies performed to investigate the effect of air injection on liquefaction resistance. In addition to this, previous research in the direction of desaturation has evolved different techniques to generate gas in saturated sand. These techniques have also been discussed in the present paper. All the field and laboratory studies have shown that even a slight decrease in the degree of saturation increases the liquefaction resistance significantly.Keywords: desaturation, air injection, liquefaction resistance, pore pressureINTRODUCTIONEarthquake events in the past, caused liquefaction of loose saturated sands at many sites in the world. The consequence of liquefaction varied from small deformations to catastrophic failures such as flow slides, lateral spreading, sand boiling etc. (Kramer, 1996). To reduce the liquefaction potential of such soils, different mitigation techniques have emerged across the world. Some of the most widely used mitigation techniques are vibroflotation, deep dynamic compaction, compaction grouting and deep soil mixing (Idriss and Boulanger, 2008).Yoshimi et al. (1989) found that the liquefaction resistance of partially saturated sand is significantly higher than that of saturated loose sand. Further, Pietruszczak et al. (2003) proposed desaturation of the saturated loose sand as a new liquefaction mitigation technique. It is observed that the liquefaction resistance of sandy soil is enhanced significantly owing to the desaturation caused during construction of sand compaction piles (Ishihara et al. 2003). Over past few years research is being carried out on desaturation of sandy soil and its liquefaction resistance ( Ishihara et al. 2003; Okamura and Soga 2006; Yegian et al. 2006; Yegian et al. 2007; Takemura et al. 2009; Eseller-bayat et al. 2013; He et al. 2013; Marasini and Okamura 2015; Zeybek and Madabhushi 2016). As a result of this, different techniques of desaturation have also emerged. Different studies conducted in this direction and their outcome has been discussed in the section to follow."

Jan 1, 2017

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network. and 2)development at a set pit digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the models and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated fur their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By R. A. Williams

Electrical impedance tomographic methods have been applied to a variety of mineral and chemical processes in the laboratory and on plant. This review paper surveys technical developments in measurement methods to enable quantitative extraction of key process information in the form of mapping of concentration profiles, mixture homogeneity and suspension velocity. The methods for determining velocity are summarized, since this is of especial interest when applied to opaque systems where most conventional optically based measurements fail. A recent significant development is the use of ultra-high speed measurement that now allows velocity vectors to be extracted for fast moving mixtures and fluids (up to several metres per second). New data are reported pertinent to low and high solids concentration flow in pipelines. Use of the methods offer improvements to design of such systems but also points to the use of tomographic electrical sensor as online flow measurement and fault detection. This offers new opportunities for applications and benefits in the design and monitoring of mineral slurries and sludges.

Jan 1, 2008

By A. du Plessis

The study summarized in this paper focused on expanding existing South African mine closure cost calculation models to provide a new model that incorporates risks, which could have an effect on the closure costs during the life cycle of the mine. This research is important because currently there are a number of mines that do not have sufficient financial provision to close and rehabilitate the mines. The magnitude of the lack of funds could be reduced or eliminated if the closure cost calculation is done in a more risk-orientated manner. The model consists of an expansion of existing closure cost calculation models, by applying the Monte Carlo risk simulation technique to model influences of external and internal changes affecting closure costs. It is shown that the proposed risk-based model provides a way to understand better the implications of uncertainty on the closure costs.

Jan 1, 2006

By R. Altindag

The rock brittleness is one of the most important rock properties that affect the drill-ability of rocks. It is supposed that the increase in rock brittleness causes the increase in penetration rate. The drill-ability of rocks depends on many factors. These factors can be separated as two parts depending on a machine, bit type, rotational speed, thrust, blow frequency, flushing, and rock properties, brittleness, compressive strength, structure, hardness, etc. In this paper, the relationship between brittleness and drill-ability index, which is used in the prediction analysis of the penetration rate of rotary blast hole drills, were examined using regression analysis. It is also seen that significant correlations exist between brittleness and the drill-ability index.

Jan 1, 2002

By R Munoz, R González, J Vallejos, A Delonca

In panel caving in underground mines, it is essential to characterise and monitor the stress and stability state of production level pillars to ensure the extraction of the mineralised ore column and the safety of workers. Pilar Norte is a sector in the El Teniente mine that forms a pillar between the undercut fronts of the adjacent Esmeralda and Reservas Norte sectors. It exists in a high-stress environment, which may induce damage to the rock mass production pillars. Generally, numerical models are calibrated using observed damage in galleries. This procedure does not discriminate between the structural condition and/or the blasting damage effects. This paper proposes a technique that uses borehole cameras to measure stress-induced damage. This has the advantage of being at the intact rock scale, meaning that the effect of geological structures is negligible and the blasting damage factor is eliminated. Comprehensive geotechnical characterisation and tomography monitoring has been undertaken at Pilar Norte to describe and determine the rock mass behaviour of the production pillars. By combining analytical, empirical and numerical models, a correlation between the measured overbreak recorded by the borehole cameras and the stress level of the pillar was developed. The methodology can be routinely applied to estimate the stress state in the production pillars.CITATION:González, R, Munoz, R, Vallejos, J and Delonca, A, 2016. Characterisation and monitoring of the stress state of production pillars at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

During harsh weather conditions, the presence of fog, dust in the environment degrades the image’s quality, which affects the visibility of drivers of heavy earth-moving machinery in opencast mines. Due to low visibility, mining operations cannot be carried out as drivers are easily prone to accidents. This paper proposes a technique that includes developing a vision enhancement system called perceptive driving assistant system for increasing visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery at opencast mines during harsh weather conditions to overcome the problem. The system consists of high-quality Internet Protocol cameras and thermal cameras for real-time image processing and other well-defined devices, which is quite capable of enhancing the visibility of the image, outlining edges of the road, and detecting obstacles present on the path of operators for smooth driving and reducing threat of accidents. A high-speed graphical processing unit has been used for quality-performance parallel computing, which is well suited for real-time operations to empower fast real-time operations. The calculated frame per second (fps) of image enhancement, object detection, and edge detection is 17.91, 15.91, and 25.09 fps, respectively. The actual frame rate is 26.07 fps, and after applying the algorithm, the final frame rate is 19.65 fps. The calculated accuracy of the object detection model is 81.23%. Field trials indicate that the developed system has performed adequately during foggy weather.

Sep 21, 2022

This paper describes the back analysis of the Pavoncelli tunnel, an hydraulic tunnel which was excavated between 1904 and 1915 in South of Italy and experienced severe damages during the 1980 Irpino-Lucano earthquake. A numerical simulation which is intended to study the behaviour of the tunnel during this seismic event is presented, also accounting for the swelling phenomenon that took place during and after construction.

May 1, 2009

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure to roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations, and trial-and-error testing. Both prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month's article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By James McGough, Lawrence Mirabelli, Ran Tamir

The paper will demonstrate how automated fragmentation photo analysis is being used at the Lafarge North America, Ravena NY quarry as part of an ongoing drill, blast and primary crushing continuous improvement process. Using on-line fragmentation photo analysis systems at both the primary crusher feed point and crusher discharge belt, data is collected to: benchmark the drill/blast process; monitor the work being done by the primary crusher; measure gradation changes in the crusher feed resulting from changes in drill/blast and measure the subsequent changes in further size reduction done by the primary crusher.

Jan 1, 2012

By Regina Maria Pinheiro

This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation in the amount of 10 wt.% on the properties and microstructure of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis. Incorporated bricks were produced in industrial scale before firing at 750°C in a Modified Caieira type furnace. The physical and mechanical properties evaluated were water absorption and compression strength. The microstructure of the fired ceramic was evaluated by optical microscopy. The environmental evaluation was made by solution test and atmospheric emission by monitoring the release of SO2, NOx and particulate material. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. The properties of the fired ceramic attend the norms. With respect to the environmental aspect, the incorporation of the waste did not impact the environment.

Jan 1, 2009