Search Documents

By K. B. Hodgins, P. Ouellette

"The North American mining industry faces challenging emissions regulations in the coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable.Westport Innovations Inc., Vancouver,British Columbia, has developed high-pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications while reducing emissions of nitrous oxides (NOx), particulate matter (PM), and CO2 with no loss in performance. This is accomplished through late-cycle, high-pressure direct injection of natural gas into a diesel engine combustion chamber at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the natural gas fuel main injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, lowspeed torque, high-power output, no engine knock, and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to the reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored with less impact on weight and space than compressed natural gas (CNG) by virtue of its increased energy density over CNG.Westport has applied HPDI technology to the Cummins QSK series engines for high horsepower applications such as power generation and mine haul trucking. HPDI can also be applied to other engine manufacturer platforms and market applications. Westport is interested in demonstrating the unique characteristics of HPDI in mine haul trucks to show diesel performance with low emissions levels using low-cost LNG fuel.Retrofitting a Tier 1 engine with HPDI would provide emissions reductions below the EPA 2006 Tier 2 standards while maintaining the performance and efficiency of the Tier 1 platform. The longer-term target is the Blue Sky voluntary standards of 3.8 g/kW-hr (2.8 g/bhphr) of NOx + non-methane hydrocarbons (NMHC), and 0.12 g/kW-hr (0.09 g/bhp-hr) of particulate matter (PM) and future standards. Typically, an HPDI engine is capable of reducing NOx emissions by 40% over diesel operation at the same efficiency. On a mining truck meeting Tier 2 standards, this NOx reduction would translate into NOx emissions approximately 14 t per year lower than under diesel operation. PM emissions are typically reduced by some 60% with HPDI fueling, which would translate into a yearly reduction of 650 kg. Similarly, engine-out greenhouse gas (GHG) emissions are reduced by 21%, resulting in a yearly reduction of approximately 950 t per vehicle.Above those of emissions reduction, efficient natural gas usage in mine haul operations would offer significant benefits in terms of fuel cost savings, which may be further combined with monetary emission credits. HPDI technology would enable operators to exercise environmental stewardship while gaining a competitive advantage in advance of new Tier 2 and Tier 3 emissions regulations. The advantages of natural gas use among mine haul truck operations can be replicated across a broad range of engines and applications."

Jan 1, 2005

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By Fred N. Kissell

In This Chapter [The explosibility of methane gas mixtures Effect of pressure and temperature on explosibility Less common sources of methane ignitions The amount of methane stored in coal Forecasting the methane emission rate Layering of methane at the mine roof When the recirculation of mine air is hazardous The importance of higher air velocity in preventing methane explosions and Mine explosions, barometric pressure, and the seasonal trend in explosions] Dealing with methane in mines and tunnels requires knowledge of the circumstances under which dangerous accumulations of methane are likely to occur. This knowledge involves the properties of the gas itself, an awareness of where these accumulations are likely to occur, and facts on how methane mixes safely into the mine air. The other chapters in this handbook address the handling of methane under a variety of specific circumstances, such as at continuous miner faces or coal storage silos. This chapter addresses some broad concepts that serve as a foundation for the suggestions provided in other chapters. THE EXPLOSIBILITY OF METHANE GAS MIXTURES Methane entering a mine or tunnel often enters as a localized source at high concentration. Figure 1–1 depicts a cloud of methane being diluted into a moving air stream. In this illustration, methane enters the mine from a crack in the roof. As the methane emerges from the crack, it progressively mixes with the ventilation air and is diluted. In the event that this progressive dilution reduces the concentration from 100% to 1%,2 as shown in Figure 1–1, the methane passes through a concentration range of 15% to 5%, known as the explosive range. In the explosive range, the mixture may be ignited. Above 15%, called the upper explosive limit (UEL), methane-air mixtures are not explosive, but will become explosive when mixed with more air.

Jan 6, 2006

By S. Sarac

In this study, graphical and mathematical methods used to determine operating points in single or multiple fan ventilation systems are summarized. The problem is mathematically formulized for parallel connected fans in which analytical solutions are not possible. For n number of parallel connected fans, a non-linear equation system that consists of n number of non-linear equation sis derived. The Newton-Raphson method, which is a numerical analysis method, is adapted to solve this non-linear equation system and the solution steps are given as an algorithm. A computer program based on this algorithm is written and its applicability is proved.

Jan 1, 2000

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980

By Ronald M. Lewis

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 00 to 90° for FeKa and from 25° to 180° for FeKa1. The wavelengths used for Fe in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): FeKa1 1.93597 A.; Feka2 1.93991 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn. X-ray diffraction crystallography using tubes with iron targets revealed a need for a handy reference for the quadratic functions of iron radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By H. F. Yancey

Traditionally the Pacific Northwest has relied on hydroelectric power, which has been both abundant and cheap. However, comparatively few hydroelectric sites capable of providing low-cost power remain, therefore the need for supplemental thermal generation, perhaps within the next decade, is generally recognized. Based on the present cost and availability of competing fuels, coal seems to be the logical choice for projected thermal power plants. Power companies and public utilities have become interested in establishing reserves of coal for future use. One deposit explored in 1958-59 lies in southern Thurston and northern Lewis Counties, Wash., near Centralia. Drilling, totaling 22,700 feet, proved the existence of 70 million tons of strippable coal--an ample reserve for the projected power plant. The coal, like most others and particularly those of Washington and Oregon, when mined in full seam section by mechanical methods, would require cleaning to make it suitable for use. The amount and nature of the impurities in this coal dictated a thorough investigation of its cleaning characteristics to establish economic factors and to insure proper preparation-plant design. Therefore, arrangements were made through a cooperative agreement to conduct such work at the Seattle Coal Research Laboratory of the Bureau of Mines. This report describes that investigation. The results are of interest primarily in connection with the utilization of this particular deposit, but some of the information developed is applicable to other deposits of low-rank coals in the West, because the impurities in these coals differ greatly in behavior from those generally associated with the higher rank coals of the Appalachian field.

Jan 1, 1961

By Robert E. Green

This Final Report summarizes the results of work accomplished under Contract No. J0215039. It is in an executive overview or executive summary format. The number and description of the various technical reports prepared and submitted is outlined. The essential changes and reasons for the revised program schedule/contract modifications actually enacted in May 1982 are discussed in detail. The evolving mines/deposits list and the accompanying criteria classifications are explained along with the verifications/justifications for adding or deleting specific mines/deposits to the list. Difficulties and problems experienced during the different phases of the project in conjunction with the ensuing remedies are highlighted. The final section of they report is devoted to presenting Davy McKee's suggestions for improvements to future MAS commodity studies. Appendix I is comprised of three of the evolving mines/deposits lists starting with the original RFP list and ending with the final completed list. Appendices II and Ill are tabulated summaries of property data including reserves/resources, assays, production, and operating costs. The figures for the specific mines/deposits are given in "range of values" so as to protect the confidentiality of the individual owners/ operators.

Jan 1, 1983

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By J. O. Marsden

Part I in this series of papers considered the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical testing and initial process development for this technology. This initial work resulted in the development of a process flowsheet utilizing superfine grinding (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160° to 170ºC, followed by conventional solution extraction (SX) and electrowinning (EW) for the recovery of copper. However, this process required a significant amount of concentrated acid to be fed to the pressure leach vessel to meet the reaction requirements, representing a cost of between $0.03 and 0.05/lb copper (2006 basis) produced by the process. It was immediately recognized that the development of a process that did not require such a large acid addition would be advantageous. This paper, which is Part II in the series, describes the development of a process that incorporates medium-temperature pressure leaching and direct electrowinning (DEW) in a novel and innovative process flowsheet. Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold Inc.) refers to this as the ?MT-DEW-SX? process. Part III in this series covers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By J. B. Boisvert, P. Oshust

A significant source of uncertainty in the diamond resource contained in kimberlite pipes is the volume of the pipes. Often the material within a pipe will be mined as ore, leaving the actual geometry of the pipe as a significant source of uncertainty. It is desirable to use stochastic techniques, rather than deterministic methods, to model pipe geometry because stochastic techniques generate multiple realizations that are reproducible and can be used to assess uncertainty in pipe geometry. The proposed methodology uses sequential Gaussian simulation of pierce point locations interpreted from drillholes through a kimberlite pipe. Kimberlite pipes are approximately cylindrical in shape; therefore, the data are transformed to cylindrical coordinates to facilitate the simulation of pipe geometry. Rather than using xyz coordinates to define the pierce points, z, ??and pipe radius are used. The radius variable can be simulated in z-??space to generate multiple realizations of pipe volume. Uncertainty in the volume of the pipe can then be evaluated. This methodology is demonstrated with a kimberlite pipe at BHP Billiton’s Ekati diamond mine.

Jan 1, 2008

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By Donald R. Johnson

Apparatus providing simultaneous differential thermal analysis, thermo-gravimetry, and evolved gas analysis, has been developed by the Bureau of Mines specifically for thermal study of oil shale and other solid, natural fuels. The apparatus is described in detail, and simultaneous analyses on a single sample of an oil shale mineral, nahcolite, and a thermal analysis demonstration compound, calcium oxalate monohydrate, are presented to demonstrate the instrument's capabilities.

Jan 1, 1970

By P. P. Rosario, D. M. Maijer

The primary crusher is a key component in the comminution process applied in open pit mines. A collaborative research project between the University of British Columbia and Highland Valley Copper (HVC) was conducted aiming at understanding gyratory crusher liner wear in the overall context of the crushing process. This paper presents an analysis methodology applied to data collected using a laser-based tool for assessing wear in gyratory crushers. Data from the wear measurements was correlated with crusher production information such as current draw and throughput. As a result of the knowledge developed during this work, an innovative way to evaluate crusher liner profiles was created and new mantle profiles were designed. This led to a reformulation of HVC’s standard liner management policy with a resulting estimated annual savings of 13% in total crusher liner cost and a 15% reduction in liner replacement downtime.

Jan 1, 2006

By Cynthia Belt

"Before energy can be saved in the materials industry, the process must be understood. At the same time, baby boomers are starting to retire. New people are entering the field without experience and training especially in methods to save energy. Various classroom courses, seminars, books, software, and websites are available for the professional to better understand the industry with the ultimate goal to reduce energy use. This paper is a review of what is currently available with some comments on potential needs.IntroductionEnergy use is high within the materials industry. For the United States, the primary metal industry uses 8% of all energy used in manufacturing (Figure 1 )1 or 1, 736 trillion BTUs per year. Sadly, while energy use is high, energy management is not universal within the industry. Counting both internal programs and external such as the utility supplier, equipment manufacturers, federal and state programs, only 66% of primary metals companies participate in an energy management activity1.For the materials field, process heating is the majority of the energy use in a plant2. Understanding and optimizing process heating is a critical need for materials energy professionals. Surprisingly, process heating is not necessarily the work addressed within an energy program. The U.S. 2006 Manufacturing Energy Consumption Survey (see Table 1) found more primary metal companies addressing lighting with 31 % participation versus 15% with process heating work even though energy used in lighting tends to be a minor (in the range ofl-3% ofa typical plant's energy use)."

Jan 1, 2013

By H Susanto, N Belluz, D Flint, A Edw

The Deep Ore Zone (DOZ) is a block cave mining operation exploiting a diluted reserve of 131 million tonnes grading 1.06 per cent copper and 0.81 g/t gold in the lower portion of the Ertsberg East Skarn System (EESS). The EESS is a calcium-magnesium silicate skarn containing in excess of 250 million tonnes of copper-gold ore, located in the Ertsberg Mining District on the crest of the Jawawijaya mountain range in the highlands of Irian Jaya, Indonesia. The EESS was discovered in 1968 where it cropped out at an elevation of 4050 metres above sea level. The Ertsberg Mining District is underlain by siliclastic carbonate and siltstone formations of Jurassic to Tertiary age. The sediments have been folded and are cut by major bedding subparallel and crosscutting structures. Intrusion of a series of igneous bodies post-dates folding and faulting. These I-type intrusions are the source for the copper-gold mineralisation found in the Ertsberg Mining District. The EESS is hosted by carbonates of the Tertiary Waripi and Faumai Formations that have been altered to calcium-magnesium silicate skarn and is situated on the southern limb of a northwest-trending syncline. The EESS is an essentially vertical tabular body with a vertical extent of at least 1200 metres and a lateral extent of up to 1000 metres. The width of the EESS averages 200 metres and locally is in excess of 300 metres. The northeast (hangingwall) contact of the EESS is a skarn reaction front in sudden contact with barren marbles. This contact coincides with a zone of localised faulting and brecciation. The EESS is bounded to the southwest (footwall) by the Ertsberg Diorite, a 3.25 Ma old intrusive. The DOZ block cave operation extends from 3040 metres above sea level to a maximum of 3388 metres above sea level, has a length of 860 metres and a maximum width of 350 metres. The DOZ is a high temperature skarn with a prograde forsterite/diopside mineralogy whose protolith is the dolomitic Tertiary Waripi Formation. The principal retrograde alteration minerals include tremolite, actinolite, serpentine, talc and chlorite. Grade is highest where bornite occurs in large dense complex intergrowths with magnetite and anhydrite. Grade has been locally enhanced in the DOZ by a late-stage pyrite-chalcopyrite hydrothermal alteration event with associated brecciation. Ertsberg Diorite along the footwall of the skarn is also included in the reserve where it is mineralised endoskarn or has been mineralised by porphyrytic or late stage hydrothermal alteration. Formation of the EESS was initiated by contact metamorphism during the intrusion of the Ertsberg Diorite with later metasomatic alteration during both prograde and retrograde phases. The bulk of sulphide mineralisation formed late in the retrograde phase. The EESS is open along strike to the northwest and down-dip with on-going exploration of these areas. Current exploration is targeting both endoskarn and porphyry style alteration and mineralisation of the Ertsberg Diorite.

Jan 1, 1999