Search Documents

By V. Galla

Waste rock facilities (WRF) generally have a large footprint depending on the strip ratio the mine plan provides. Considerable planning is involved during the initial phase of the mine plan regarding the location of the WRF. As the mining operations are commenced the locations of the WRF change accordingly with the variations in the mine plan involving feedback and support from local communities and stakeholders. Waste rock facilities management becomes challenging when the area available for placement is limited due to terrain topography, environmental and permitting constraints. Risks associated in the design of waste rock facilities constitute particle size of rock, chemistry associated with the rock for reactivity and stability of the over all facility. This paper will provide some insights on designing, scheduling and managing a WRF. Emphasis on geotechnical, geophysics and geochemistry aspects of waste rock with reference to design, construction process and scheduling of WRF are also presented. Design improvements in the reclamation slope of WRF for erosion control will be discussed. Continuous improvement (CI) methodology will be introduced in the process of WRF operations. Current practices and future recommendations towards sustainability and consistency in operating WRF will be discussed in conclusion.

Jan 1, 2011

By Constance Holmes

President Lien presented Mrs. Holmes with the first of speaker appreciation gifts presented by his firm Amax Coal West, Inc. These were books by Rand-McNally entitled The Executive Golfer Guide. Following the coffee break, Clark Moseley presented the first annual Institute Safety Achievement Awards for the safest mines in the eight member state region. The awards were based on: 1. Total man-hours 2. Total number of lost time accidents 3. Incidence rate 4. Number of S&S violations 5. Description of safety program 6. Safety awards received 7. Health and safety training efforts 8. Safety Policies 9. Does the operation take employee suggestions and implement them? 10. Letter(s) of commendation from agencies individuals The awards were judged by the senior/graduate level class of Mine Safety & Health at the Colorado School of Mines under the supervision of professor Edward Hollop. The two handsome traveling trophies were awarded to and accepted by: Surface: Big Sky Mine. Colstrip, Montana Gordon Brannon, Manager of Safety Underground: Skyline Mine, Scofield, Utah Dave Hales. Safety Supervisor and Doug Johnson, General Production [ ]

Jan 1, 1998

By P W. Wypych, D Curry, A P. Grima

The market has become highly competitive for engineering and equipment vendors, who are challenged to reduce costs while improving efficiency and productivity of mine operations through plant improvements and expansions. Although conveyor transfer systems account for a small percentage of the infrastructure cost of a mine, they form an integral part of the process supply chain. Malfunctions or suboptimal performance can result in substantial financial cost from delayed start-up, unscheduled downtime, reduced throughput and increased maintenance costs.Discrete element modelling (DEM) is a powerful simulation method used to virtually prototype and test the performance of transfer equipment throughout a design cycle. When developed and applied correctly, DEM can provide insight into performance that exceeds the traditional analytical methods, especially when dealing with complex ore properties, behaviour and/or situations.Using case studies sourced from the authors’ recent research and industrial project work, this paper will address the industry goal to increase efficiency and productivity as well as the methods available to the engineers responsible for delivering designs that meet the aims of this strategic approach.The main focus of the paper will be the new calibration technology, which has been developed by the authors to generate DEM material models that are linked to real-world properties and flow behaviours via unique dynamic testing and innovative parameter calibration methods. These calibrated DEM material models can be deployed by engineers into their existing workflows, whether it be for feasibility studies, concept or final design, plant troubleshooting or optimisation.This new technology allows engineers to gain greater insight than that provided by traditional approaches to the design of transfer chutes and other process equipment and also allows informed design decisions to be made that meet industry efficiency and productivity requirements.CITATION:Grima, A P, Curry, D and Wypych, P W, 2015. New discrete element modelling calibration technology to facilitate the increased efficiency of ore handling and processing operations, in Proceedings Iron Ore 2015, pp 449–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J. Crummy, I. K. Anderson, A. J. Hall, R. S. Haszeldine

Bedrock gold mineralisation has been located in association with an extensive float train 25 km west of known alluvial gold. It is in the form of open, matrix-supported breccias comprising pyritic quartz/sericite clasts in a vuggy, cherty chalcedonic and crystalline quartz matrix. Fluid inclusions in pyritic clasts indicate trapping temperatures for gold mineralising hydrothermal fluid of 170-240 degrees C. This mineralisation could represent the upper part of a feeder zone to an exhalative hydrothermal system. It is possible that other high-level feeder zones could be preserved elsewhere in the area. Deep weathering of such a system could provide a source for the alluvial gold localities near Helmsdale. It is suggested that east and central Sutherland presents good prospects for exhalative epithermal gold mineralisation and the associated feeder zones

Jun 19, 1905

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

By I. A. Mwamba

Titanium sponge, which is almost pure titanium, is extremely ductile and not easily processed into titanium powder. One method of producing powder is the hydride-dehydride (HDH) process, where titanium sponge is hydrided to form brittle titanium hydride (TiH2). Titanium hydride is easily milled to produce powder and is then dehydrided to form Ti powder. In this work, titanium hydride powder obtained from titanium sponge was used as a starting material for blending and mechanical alloying with elemental powders. Firstly, titanium hydride powder was blended with aluminium elemental powder to produce a homogenized powder, which was then compacted and sintered to produce powder metallurgy compacts. Secondly, titanium hydride powder was mechanically alloyed with aluminium elemental powder and then compacted. The mechanically alloyed powder was characterized in terms of particle size distribution, morphology and microstructure. In both blending and mechanical alloying, the green compacts were characterized by assessing the green density, while the sintered compacts were characterized by their sintered density, microstructure, and hardness. The two processes have resulted in the formation of TiA13 intermetallic compound. It was established that by simple mixing and homogenizing, titanium hydride can be used as a starting material to produce powder metallurgy components in which porosity is a benefit rather than a problem, much akin to metallic foams. From the products obtained in the TiHz-Al system, it appears that titanium hydride can be used as a precursor in mechanical alloying. However, the possible formation of complex hydrides may introduce detrimental properties, and needs to be further investigated. For the production of non-porous components, it would be advisable to dehydrogenate the TiH2 powder before milling i.e. producing titanium powder by the hydride-dehydride (HDH) method. Keywords Mechanical alloying, titanium hydride, titanium aluminide and blending

Jan 1, 2011

By Santiago Faucher

Molten slag from pyrometallurgical furnaces is tapped at high temperature, carrying a large amount of thermal energy. But the common slag dumping and water granulation methods used for slag treatment do not permit energy recovery. Furthermore, water is present in these processes and while operations are designed to minimize risks of steam explosions, from the contact of slag with water, these common slag handling practices have never been inherently safe. Common handling practices do permit some slags to be sold, but often in low volumes at low prices. Dry granulation offers advantages over these common slag handling practices, including the production of by-products, the recovery of thermal energy, and the eliminated consumption and safety hazards of water. For these reasons, there have been various studies in dry granulation and heat recovery, but most have never been brought to commercial scale due to scalability and cost challenges. Ecomaister- Hatch has developed and brought to commercial scale a reliable and simple dry granulation and heat recovery technology. Here we review common slag handling practices, the developments in dry slag granulation over the last three decades, introduce the Ecomaister-Hatch dry slag granulation process, and elaborate on future applications of the technology in the processing of argon oxygen decarburization and blast furnace slags.

Aug 17, 2017

In the late 1970's and early 1980's a considerable number of large scale open pit mines were developed in N.S.W. and Queensland. At the time these mines were planned, the industry was characterised by rising coal prices, rising fuel prices, and a host of other labour and government constraints different to the situation today. Yet some mines have clearly been able to cope with this change much better than others. While one mine may now be expanding and profitable, its neighbour may still be labouring under painful adjustment processes. This paper examines the major reasons for this difference. It suggests more robust criteria for assessment of future projects to reduce their sensitivity to changes outside management control.

Jan 1, 1990

By Taekhee Lee, Steven Mischler, Shawn Vanderslice

Diesel-powered equipment is widely used in the underground mining industry and their popularity results from properties including efficiency, versatility, reliability, and durability. In the U.S. approximately 7,700 diesel engines were used in 177 underground metal and nonmetal mines as of 2005 [MSHA 2005], and these numbers have likely increased since that time. Diesel engines have been shown to be a major contributor to submicron carbonaceous, respirable, and total particulate mass in the air of underground metal mines [Zielinska et al. 2002, McDonald et al. 2003], and their extensive use results in approximately 13,000 underground metal/nonmetal (M/NM) miners (MSHA 2005) in the U.S. being potentially exposed to aerosols and gases emitted by diesel engines (MSHA 2001, MSHA 2006). Exposure to diesel exhaust has been linked to adverse health outcomes including cancer, cardiovascular, and respiratory diseases (Attfield et al. 2012, Silverman et al. 2012), and in 2012 diesel exhaust was categorized by the International Agency for Research on Cancer (IARC) as a Group 1 human carcinogen (IARC 2012). Exposure to diesel particulate matter (DPM) is especially concerning for underground miners since underground mine environments have been shown to have some of the highest levels of diesel exhaust in the U.S. (EPA 2002, MSHA 2001, MSHA 2006, Pronk et al. 2009). Due to the potential for elevated DPM concentrations in mines, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/ nonmetal underground miners to DPM to an eight-hour time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, MSHA 2006, MSHA 2008). Since this rule went into effect, DPM exposures have been reduced, but are still elevated when compared to other occupations (Pronk et al. 2009, Noll et al. 2015). MSHA compliance data between 2005 to the present show that underground blasters represent 21% of all DPM overexposures in M/NM mines and are one of the highest exposed professions in mining often resulting from low ventilation in the area where blasters are working. Because mines have difficulty controlling DPM in these low ventilation areas, additional control technologies may be needed to reduce exposures. Administrative controls, where miners work on off schedules or upstream of diesel vehicles to avoid the exposures to DPM (Noll et al. 2015) is one possibility, but these types of solutions are not always feasible or practical. A canopy air curtain is another potential control technology to help reduce exposures of blasters to DPM. Listak and Beck (2012) showed that this control technology reduced respirable dust concentration under a roof bolter’s canopy by 67%–75% and recommended air velocities greater than 0.5 m/s for dust reductions of greater than 50%. Additional work showed that a canopy air curtain could be designed for a shuttle car, and some initial testing by the National Institute for Occupational Safety and Health (NIOSH) showed reductions of respirable mine dust between 66% to 70%. As seen in Figure 1, the canopy air curtain delivers clean air over the operator’s breathing zone. A fan draws in air through a filter to capture the dust and then supplies clean air beneath the canopy where a miner is working. The use of the canopy air curtain to reduce exposures to diesel particulate matter was first discussed by Noll et al. (2020). In this study the diesel canopy air curtain (DCAC) reduced the DPM concentrations under the canopy by up to 90%. For this research the DCAC was designed to attach to the basket cover of an ammonium nitrate fuel oil ( ANFO) loader (Figure 2) and provide clean air blowing over the miners as they work in the basket. The initial tests used clean air drawn from the mine’s intake and did not try to filter the DPM from the air. Filtering DPM has extra challenges when compared to filtering mine dust particles. The particles of DPM are smaller (submicron and nanometer) than dust particles (greater than 1 micron); therefore, the filtration system must be adjusted to capture submicron particles. A MERV 13 filter was used in previous canopy air curtain research on mine dust control, but this filter is only designed to capture 50%–75% of submicron particles, and this capture efficiency is too low for removing DPM, so a higher efficiency filter is needed. Higher efficiency filters increase the pressure across the filter media which results in decreased airflow or leaks around the filter and reduces the effectiveness of the control for protecting miners from DPM. The optimal filter needs to capture DPM particles at a high efficiency while still allowing the needed airflows to prevent contaminated air from entering the miner’s breathing zone. Listak and Beck (2012) recommended velocities greater than 0.5 m/s for dust reductions of greater than 50%. However, airflows too high have been shown to reduce miners’ thermal comfort; Roghanchi et al. (2016) suggest the optimal velocity for thermal comfort is between 1–2 m/s. Thus, airflow over the miner should be limited to the range of 0.5 to 2.0 m/s. This current study presents the results from research evaluating the reduction of DPM concentrations, under the DCAC, when using a higher efficiency filter (MERV 16) to remove DPM from the DCAC airstream.

Feb 1, 2024

By Gorzalczynski. Stan

The recent trend in underground mine developments is ?big is better?. This is most certainly evident in the mine shaft and the conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed for the past fifty years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident, remains conceptually unchanged from Elisha Otis? design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha?s invention with the last major design change occurring in the late 1940?s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment but also, an increased awareness toward safety.

May 1, 2002

By Jesús L. Valenzuela, José R. Parga, Salvador Aguayo, Héctor Moreno

The Merrill Crowe zinc-precipitation process has been applied worldwide on a large number of operations for the recovery of gold and silver resulting in a higher consumption of zinc dust from cyanide solutions. However, in some of plants this precipitate is of low quality, because lead, cadmium and especially copper are precipitated along with gold and silver. The low quality precipitate also requires more fluxes in smelting and shortens crucible life. In this study, a process is introduced to remove copper, silver, lead and cadmium from barren solutions following the Merrill-Crowe process. Copper and silver are removed by precipitation in a serpentine reactor, using sodium sulfide as the precipitator, and sulfuric acid for pH control. The recovery of lead and cadmium ions with natural hydroxyapatite using cow bone powder (CBP) as a new adsorbent material, is introduced. CBP is capable of removing lead and cadmium ions from aqueous cyanide solutions with 99% efficiency. It has the ability to compete with other existing commercial adsorbents for the removal of lead and cadmium. Results show that pH value has a significant effect on copper cyanide removal efficiency, and it was determined the optimal pH range to be 2 - 3. At this pH value, the copper cyanide removal efficiency achieved was up to 99 %; and for the cyanide associated with copper cyanide complexes, the recovery was 90%. Finally, the precipitate quality was improved 400% .This procedure was successfully run at three mines in México.

Jan 1, 2014

By S. Frimpong

The cable shovel excavator is used for primary production in many surface mining operations. A major problem in shovel excavation is the variability of material diggability, resulting in varying mechanical energy input and stress loading of shovel dipper-and-tooth assembly across the working bench. This variability has a huge impact on the shovel dipper and tooth assembly in hard formations. In addition, the geometrical constraints within the working environment impose production limitations resulting in low production efficiency and high operating costs. A potential solution to the above problems is the application of an intelligent cable shovel excavation(ICSE) technology. In this paper, dynamic models of the cable shovel excavator are developed with numerical examples. These models form the basis for developing dynamic shovel simulators for an intelligent shovel excavation technology. The dynamic equations are developed using the Newton-Euler techniques. The path trajectories for efficient excavation, dynamic velocity and acceleration profiles, and dimensioned parameters for optimum feed force, torques and momentum of shovel boom-bucket assembly are modeled and used for efficient excavation. The optimum digging forces and resistances for the cable shovel excavator are modeled and used to predict optimum excavation performance.

Jan 1, 2003

CVRD was established on June 01, 1942, during the Second World War, through an agreement between Brazil, the United States and the United Kingdom, to produce 1.500.000 tons/year of iron ore from Itabira mines in the State of Minas Gerais. As a result of several circumstances and political problems (the end of the 2nd World War reduced the Anglo-American support to its development and implementation), the venture just reached the originally targeted production 10 years after its establishment, operating within a mine, railway and port integrated system. Currently, this operational system from the South of Brazil owns mines in the State of Minas Gerais with an annual capacity of approximately 65 million tons, 900 km of railways, of which more than 500 km is a double line railway, six pelletizing units and the Port of Tubarao for ships with large carrying capacity.

Jan 1, 1994

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980

The development of information concerning mesothelioma in South Africa started with the 1959 finding of Dr. J. Christopher Wagner of cases of mesothelioma in persons living in the vicinity or working in crocidolite mines in Cape Province. After more than 40 years, the data from South Africa now provide important insights into the differences in mesothelioma risk associated with different asbestos fiber-types. Three case series reports and one analytical report were reviewed in this session. In total, information on 504 proven cases was presented. There were 28% of cases arising from occupational exposure in mining, 35% from non-mining occupations, 23% from environmental exposures; 14% where no exposure was established and 9% where the exposure was unknown. Among the 129 cases for which occupational exposure and asbestos fiber-type were established, 115 cases were associated with occupational exposure to Cape crocidolite; 1 case associated with occupational exposure to Transvaal crocidolite and 9 cases with occupational exposure to amosite (grunerite asbestos) and 4 cases with occupational exposure to mixed fiber-types. There were no cases associated with chrysotile asbestos. There were 33 cases of environmental mesothelioma linked to Cape crocidolite exposure and 2 to exposure to amosite and crocidolite but none to Transvaal amosite alone or to chrysotile. The evidence shows that amosite is capable of causing mesothelioma but that the major risk in South Africa is associated with Cape crocidolite.

Jan 1, 2008

By G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26 million tons of ore of which 16 million is mined and milled on site. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centered around the Pyroxenite ore. This will lead to substantial increases in production costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

The Acid Leaching Process for the Synthesis of Zeolitic Material from Paper Sludge Ash

Sep 13, 2010

By C. E. Hennig

On January 1, 1961 there were 311 petroleum refineries in the United States with a total crude-oil throughput capacity of slightly more than 10 million barrels per day, according to the Bureau of Mines' annual survey. Compared with a year ago, this represents net increases of one in the number of plants and 109 thousand barrels per day in total capacity. Contributing to this increase was the completion of two new plants, one in Hawaii and another in Michigan, during the year. At the beginning of 1961 the industry was building facilities which will increase this overall crude capacity by 36,500 barrels per day. As part of its building program, it was also replacing 329,000 barrels per day of its present capacity. Of the total 10 million barrel per day installed capacity, the industry reported 380,000 barrels per day as being shut-down on January 1, 1961. This included 11,500 barrels per day considered inoperable without extensive reconditioning.

Jan 1, 1961

By I. J. Brown

Paper prepared for presentation at Industrial minerals and the environment, held in Leeds, 24-35 September 1990. The need to submit an environmental statement (EIS) has certainly increased the workload of those concerned with both its production and assessment. However, there is now good evidence that the system is enhancing public confidence in the minerals industry in particular and improving relationships between the developer, planning authority and those consulted such as statutory bodies, parish councils, civic societies, nature conservation interests and ramblers

Jan 1, 1991

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002