Search Documents

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By D. K. Chibwe, P. Taskinen

"This investigation consists of a numerical and physical modelling exercise on flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a 0.2-scale cold model of an industrial Peirce-Smith converter (PSC). Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The 2D and 3D numerical simulations were carried out using volume of fluid (VOF) and realizable k-e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions. Measurement of mass transfer indicated that fluid flow in the PSC is stratified. Blowing configurations and slag volume both had significant effects on mixing propagation, wave formation, and splashing.As a potential process alternative to increase conversion efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined as well as lateral blowing conditions, and the results of the combined concept are encouraging."

Jan 1, 2015

By R. W. Welker

A technique was developed for sampling and analyzing airborne dusts in diesel-operated, underground, metal, and nonmetal mines. Samples were taken using personal respirable samplers, operated as area samplers, and an 11-stage cascade impactor. Real-time particle size distribution and concentration measurements were made with a quartz crystal micro-balance cascade impactor and a portable electrical aerosol analyzer. The materials characterized were minerals (by XRD), elements (by XRF), particle size distribution and concentration (gravimetrically), and organic constituents (by HPLC). The method was used to characterize dusts generated at the chute pulling operations on the main haulage level of an underground tungsten mine. Analysis showed that respirable dust concentration ranged from 0.8 to 2.3 mg/m3. It consisted of silica (3-7%); organic constituents from diesel exhaust (0.11-0.31 mg/m3 equivalent airborne concentration); and mineral dust (39-100%). The remainder was diesel exhaust particles. It was concluded that size selective sampling may be used to estimate the ratio of diesel exhaust to nondiesel dusts in the respirable fraction.

Jan 1, 1982

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By David A. Hart, Barry P. Osborn, Richard J. Totty, Ana T. Carvalho, Max B. Elliott

This paper addresses the experience designing and installing bored piles for the King’s Cross area. This includes continuous flight auger and rotary bored piles, with a range of diameters between 600 mm and 1200 mm, reaching a maximum depth of 56 m below ground level. Existing Network Rail Thameslink twin bored running tunnels are located directly beneath the subject plots. These tunnels have an external diameter of 6.6 m and the crowns of the tunnels are very shallow, in some cases just 10 m below the existing ground level. Some plots needed piles to be installed in close proximity to the tunnels, which required additional control measures and contingency plans. Pile verticality was monitored as the tip of each pile advanced and in-tunnel monitoring readings were verified and are presented. Lessons learned from designing, installing and testing the piles and monitoring the tunnels are addressed in this paper.

May 1, 2022

Jan 1, 1999

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By A. E. Ketler

A second generation lighting system was installed in the Greenwich Collieries longwall. This report describes the hardware, installation, maintenance, and final results of the program.

Jan 1, 1978

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

By David Ziegler, John Babcock, Gregory Poole

On December 9, 2003 at 3:59 PM EST an earthquake with a 4.5 magnitude occurred in central Virginia. According to a survey on the US Geological Survey website, this quake was felt as far away as Bridgeton Missouri, approximately 683 mile from the epicenter1. We recorded the vibrations from this earthquake on 14 seismographs that were set up for monitoring vibrations from blasting activities in the area. Having this data gave us an opportunity to compare earthquake and blasting vibrations. The amplitudes, frequencies and duration were much different than vibrations from mining and construction blasting. A common question we get from homeowners when discussing vibrations from blasting activities is “How does that compare to the Richter scale?” The goal of this report is to provide some simple answers for that question. The Richter and Mercalli scale are compared to the particle velocities in order to show their relationship.

Jan 1, 2005

By N. Mashaba, D. Botha

The aims of this study were to investigate the factors that influence women’s engagement in technical positions in the South African mining sector and to determine what could be done to promote their successful participation. A convergent parallel mixed-methods research design was used to ascertain the factors that facilitate, inhibit, and influence engagement. In the quantitative phase of the study, questionnaires were circulated to women employeees; and in the qualitative phase, semistructured interviews were conducted with employer representatives, most of whom were human resource personnel. Confirmatory factor analysis showed that the three-factor structure (vigour, dedication, and absorption) of the Utrecht Work Engagement Scale fit the sample data reasonably well. Although there is room for improvement, respondents demonstrated acceptable levels of engagement in their work. On the other hand, the qualitative findings showed that employee engagement is impacted by unfavourable working conditions, work–life balance, and the mining industry’s male-dominated work culture. The findings showed that employee engagement should be elevated to a core human resource function. To increase the participation of women in mining, human resource professionals are encouraged to collaborate with mine supervisors, managers, and employees to develop programmes that promote employees’ absorption in and dedication to their work.

Nov 6, 2023

Jan 1, 1998

The phosphorus content of the banded iron formation (BIF) and of the associated iron ore deposits in the north west of Western Australia is known to vary widely, a fact which has considerable econ~mic significance. Trendall and Blockley (1970) have described the variety of textural appearances of apatite in the Hamersley Group BlF, and suggest that apatite may account for the entire phosphorus content of the unaltered BIF.A preliminary investigation using an M.A.C. electron microprobe analyser has shown that, at least in some iron ores and in partially enriched BIF and associated shales, the phosphorus occurrence is more complicated than this. A suite of samples was examined from one location which covered the entire Dales Gorge Member and some adjoining macrobands in the Mt. McRae shale, together with samples selected for their high phosphorus content, degree of ore enrichment, and position relative to the enrichment zone. Calcium apatite was not observed in any sample of ore from this sequence, despite its ubiquitous occurrence in the BIF. Silicate mineralogy in the enriched regions also differs from that in the BIF, but this change has not yet been studied in detail.The phosphorus content of goethite in one orebody is often high and appears to be in solid solution in the goethite structure. It shows little or no variability on a micro-scale within a grain, except where theremay be a zoned enrichment near boundaries and solution channels. There is also a limited solubility of phosphorus in hematite (the maximum observed by the author is 0·1 per cent P); but where the hematite is martitic (after magnetite) its phosphorus content is always low or zero. In some bands, martitic hematite has been hydrated to goethite, and this also has a very low phosphorus content. Phosphorus was not found in the silica or silicates in the ore, and even when iron enrichment is just beginning, a limited suite of samples from the BIF suggests that the phosphorus content of the chert microbands is almost entirely in the microscopic goethite nuclei (after riebeckite) scattered throughout the chert. The ability of goethite and hematite to accept phosphorus...

Jan 1, 1973

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016

By John Watson, Tom Treleaven

This guide presents nur-nerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide Quick reference by number of decks or bunch blasting. The pattern IS presented in the section where the highe!$ number of decks works. It should be noted that patterns applicable to multipledackshwtings are alsoapplicsblefor fewer decks.

Jan 1, 1995

By R. R. Sayers

Under compuision of the present urgency to implement the President's promise to make the United States the arsenal for the democracies there is a tendency to demand a relaxation of restrictions on hours of labor and to speed up all industrial processes. The pressure is the more insistent with growing realization of the importance of the time factor in the success- ful prosecution of the war effort and the lack of skilled workers due to (2) operation of the draft, lack of an apprentice system in industry, and loss of skill by workers unemployed for long periods during the depression. With "total" war such as it is today the probabilities are that everyone will be required to exert greater effort (in many instances in activities to which they are unaccustomed) for longer periods than ever before has been necessary. The question arises, "What will be the aftereffects as well as the immediate effects on health, safety, and efficiency?" A review of the literature leaves the impression that this question has not been an- swered completely, especially as regards the ultimate effects. Mechanization, speeding up of industrial processes, mass produc- tion, and the small industrial concerns present many problems to indus- trial medicine. Does the tendency to expect the worker to produce at full speed all the time he is on the job decrease the effectiveness of the shorter working hours and cause undue fatigue, loss of efficiency, and increased accident proneness? The answer is important as this condition is likely to be intensified by the exigencies of the present emergency. According to Viteles (1)3, The increased tension under such conditions of work appears to offset the savings in muscular force made pos- sible by the machine. The tension, the speed, the subject- tion to specialization of work and a rhythm uncontrolled by the individual promote fatigue, characterized by a "decrease in the power to work, a decrease in pleasure taken in work, and a decrease in the enjoyment of the hours spent away from work."' The crowding of workers in temporary structures without proper provision for comfort and health may add greatly to the general fatigue factors already present in many industrial establishments. In 1932 Lockhart (2) stated that the production and maintenance of a healthy, satisfied industrial population is the most urgent necessity, involving problems so serious as to constitute a national task too great economically to be relegated to industrial concerns. If this was true in 1932, it must be doubly so today.

Jun 1, 1942

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

"This paper describes some of the methods and equipment used for fine milling of minerals, and gives particular attention to the Vibro Energy system.In addition, the paper describes a specific application in the gold mining industry. This is the 200 tpd plant built by Anglo American Corporation at the President Brand Mine in South Africa in 1985, now a division of Freegold. This plant treats a gold bearing pyrite flotation concentrate which is finely ground to 15 microns prior to cyanidation and carbon-in-pulp (CIP). l .0 INTRODUCTIONFree milling gold ores are those that yield acceptable dissolution and recovery of the gold following grinding to what can be described as normal fineness, frequently between 50% and 90% passing 74 microns.Increasingly, gold metallurgists are faced with ores that are refractory. The traditiona1 treatment route for refractory gal d ores and concentrates has been by roasting, but for environmental reasons this is becoming less acceptable, or in some areas of the world, totally unacceptable. New methods of treating refractory gold ores are being developed and applied in practice. These new methods include pressure and biological oxidation. Higher gold liberation can also be attained by increasing the fineness of grind, although with conventional systems there are economic limits to this.In flowsheet development and test programs on new deposits, a standard procedure is to establish the relationship between the grind and subsequent go 1 d extraction. The normal situation is that gold extraction increases as the ore, or concentrate, is ground finer. Typically, this relationship is as shown in Fig. l, where the incremental additional extraction is very small once an optimum, or economic, grind has been achieved. This generally app1ies whether the material is free milling or refractory. The limits to grinding are set by the type of equipment which is commonly in use, usually ball mills. These mills have the obvious advantage of high capacity, however, they are increasingly inefficient as finer grinds are required. In general, ball mills are used to reduce ore to some agreed percentage passing 74, or possibly 53 microns."

Jan 1, 1988