Search Documents

By T. Peters, W. C. Ferguson

"Shebandowan is about 600 miles west of Sudbury and 50 miles west of Thunderbay close to the trans Canada highway. Shebandowan Lake is about 38 miles long. The ore body is located between No. 1 and No. 2 shafts at the lower end of the lake. The economic mineralization lies between 200 and 2000 feet below. Years ago development of this ore body would probably have entailed draining the lake and using the open pit method to mine the ore.The water of Gold Creek which flows into Lake Shebandowan is representative of all local waters and is very close to rain water in purity. It is obvious that any industrial water discharged would have a measurable impact on the local water. The dissolved solids content is low and consistent with what is normally found in northern Ontario.A Koepe headframe is the only visible evidence of the mine from the lake. The Koepe headframe is esthetically pleasing and quiet in operation. The structure is of concrete to control noise. Noise from ore dumping is controlled by dumping underground to an ore pocket 400 feet below the surface. A 3600 foot conveyor belt carries the ore underground to the mill and is out of sight of the lake and the cottagers. The main objective to all our environmental efforts has been to preserve the natural beauty of the region. The mill is housed in a conventional metal-clad-siding building painted in esthetically pleasing colours. A single service building houses warehouse, dry storage and offices. The area surrounding the mill and service building is paved or grassed and drainage from this area is collected and pumped to the tailings area. Air intake silencers are installed on the compressors which are mounted at the back of the mill. Sound measurements taken on the lake indicate that noise suppression is excellent."

Jan 1, 1975

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By Jules Gordon

Presents the results of mining tests conducted on a forward rotating bucket wheel excavator designed to continuously mine coal at 1080 tons/hour, Goals of the program are to determine the feasibility of the forward rotating bucket wheel principle as an effective means of reducing fragmentation and loading costs associated with surface mining, with additional benefit in reducing, coal preparation costs and stripping overburden. Tests took place at the Navajo Mine in Fruitland, New Mexico, Results show that the excavator performed as expected and can reduce fragmenting and loading costs up to 80°. Presented are: 1) production machine design specifications and projected economies extrapolated from the test data, and 2) recommendations for further work in dust control.

Jan 1, 1977

By Bernard Hertlein, Chia K. Tan

"The move to LRFD methods for structural design by AASHTO, ACI, AISC , ASCE, and the FHWA has been a major change for the American construction industry. The deep foundations industry has arguably been placed most at risk by this situation, because of the need for, and the difficulty of providing, reliable quality assurance.LRFD is attractive for both the owner and the engineer because it promises cost reductions, but the assumption underlying LRFD is often overlooked - that the acceptable margin of safety can be rationally reduced, thus saving costs, provided that all the factors involved are closely controlled. This means that both the quality of the materials and the quality of the construction work must be closely monitored, and held to an acceptable standard.This paper describes the type of comprehensive quality management program that is needed in deep foundation construction projects based on LRFD. Case histories are used to illustrate the importance of both adequate inspection and reliable testing to a comprehensive quality management program.IntroductionOver the last thirty years, the major organizations that set standards and practice policies for the American construction industry, such as the American Association of State Highway and Transportation officials (AASHTO), the American Concrete Institute (ACI) , The American Institute for Steel Construction (AISC), the American Society of Civil Engineers (ASCE), and the Federal Highway Administration (FHWA), have embraced Load and Resistance Factor Design (LRFD) as an alternative to, and in some cases, a complete replacement for, Allowable Stress Design (ASD). AASHTO first published a new set of LRFD-based design guidelines for bridges in 1996, with several revisions in 1997, 1998, and 1999 (AASHTO, 1996). The 1996 AASHTO Bridge Design Code was the first in the United States that required foundations to be designed using LRFD procedures. LRFD has a clear advantage over conventional ASD where variability in material strength, bias in design methodology, and degree of construction quality can be rationally accounted for to achieve an acceptable level of risk."

Jan 1, 2005

By A. A. Cochran

The purpose of this Bureau of Mines research was to investigate the theoretical and practical aspects of using ionizing radiation to promote chemical reactions that are of interest to metallurgists, and to carry out a radiation study of a suitable reaction. The effect of 44,000 roentgens per hour of 120,000-volt X-rays on the chlorination of highly pure mixtures of rutile, carbon, and various catalysts at temperatures up to 540° C. is described. At these low temperatures, recoveries were very low; however, in the eight different systems studied, an increase in yield due to X-rays was statistically significant in two instances and was of borderline significance in a third instance. In the other five systems, the differences in yield were not significant. Impurities and added catalysts caused relatively large variations in the yield of TiC14 from the reaction. Although the catalysts employed were reported in the literature as positive catalysts for the reaction, most of them were negative catalysts for the highly pure system studied. With only one exception, each increase in the purity of the charge resulted in a decreased yield of TiCl4. The experimental results indicate that many substances catalyze the reaction studied and suggest that the differences in reactivity of the charge stocks may be due to their various contents of positive and negative catalysts.

Jan 1, 1962

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By F. F. Skiba, P. J. Root

A mathematical model has been used to investigate crossflow effects in a stratified reservoir during an idealized displacement process. A process in which one incompressible fluid displaces completely another incompressible fluid of the same density and viscosity was considered. The reservoir was assumed to be composed of homogeneous layers which are discrete but interconnected. Approximate five-spot flow geometry was simulated by arranging two pie-shaped cylindrical (two-dimensional) wedges in series. Some of the common production methods rely, for their effectiveness, on the fact that the formation consists of isolated strata. This is particularly true of selective plugging and single-zone production-injection methods. The effectiveness of these techniques for several cases in which adjacent strata are in communication has been evaluated. The usual production-injection schemes for fluid injection processes involve using the same completion interval in both the production and the injection wells. The efficiency of this, as well as alternative productioz-injection procedures has been examined for some cases involving communicating strata. INTRODUCTION The performance of many fluid injection projects is marred by early breakthrough and by production of a high percentage of the displacing phase after breakthrough. This channeling effect, if it occurs in reservoirs which have large permeability variations, is often explained on the basis of a model composed of discrete, isolated strata. Corrective or preventive measures based on this same model are also common. The behavior of stratified models has been the subject of considerable study. An excellent review of the early literature was given by Seba.1 Studies of the depletion performance have since been made for continuous, unrestricted communication between strata2-4 and for production from one permeable bed in continuous but restricted communication with an adjacent permeable bed.5,6 Model studies of displacement processes in stratified systems with crossflow also have been reprted.7-12 Finally, methods which account for crossflow have been developed for computing displacement behavior in stratified systems.13,14 Most methods for controlling or preventing channeling involve some change in the interval open to production and/or injection. Although many variations of the selective completion problem have been studied in regard to the depletion of a reservoir, little attention has been given to the behavior of a displacement process under similar conditions. Sebal used a resistance network model to study the performance of a process in which one incompressible fluid displaces an identical fluid from a linear, stratified reservoir. He investigated the possibility of improving the vertical coverage by limiting the completion interval of the production well. This investigation deals with techniques in which selective completion of the production and/or the injection wells is used in an attempt to control channeling. At one extreme, selective plugging and single-zone isolation (assuming perfect execution) should be successful if the reservoir is actually made up of independent strata. At the other extreme, they can hardly be expected to be successful if the channeling is caused by a mechanism in which stratification effects are negligible even though there are extreme variations in the formation permeability and/or the injectivity profile of the wells is not uniform. By contrast, it is difficult to anticipate the effect that the amount of communication between the beds of a stratified system will have on the efficiency of selective completion techniques. The objective of this study is the quantitative determination of the effect of communication on the behavior of some particular stratified systems which will at least lead to qualitative conclusions.

Jan 1, 1966

By Badiozamani Khosrow

Introduction The mining industry has been using computers since the late 1950s. Despite this early start, the use of mine planning software is not a common practice in many operations. But the trend might be changing because of the availability of relatively inexpensive personal computers (PC). The introduction of these machines has generated unprecedented interest by mine managers to computerize their planning operations. However, some managers have become disappointed with the PC's lack of adequate software and the inability to handle the massive amounts of information required for modeling. This paper is an attempt to shed some light on the future of computers in the mining industry. It will examine: • historical progress in the computer industry, • future advances in the computer industry, • historical usage of computers in mining, and • future alternatives available to mining. Historical Progress The computer industry has come a long way since the first full-fledged electronic digital computer Electronic Numerical Integrator And Calculator (ENIAC) was built in 1946. This machine weighed more than 27 t (30 st). It contained 19,000 vacuum tubes, occupied 139 m2 (1500 sq ft), and could perform 5000 additions per second. By contrast, today's fastest, commercially available computer is the CRAY-X. It weighs less than 5 t (6 st), has no vacuum tubes, occupies less than 9 m2 (100 sq ft), and performs over 100 million operations per second. This is an incredible advancement in less than 40 years. One person commented on the rate of advancement in the computer industry. He suggested that if the auto industry had advanced at the same rate as the electronics industry, we could buy a Rolls Royce for $2.75 and it would run

Jan 9, 1984

The ore is very 'refractory. It consists essentially of arsenical pyrites, iron pyrites, zinc blende, galena, antimony as sulphide and probably, in combination with galena, as Jamesonite, magnesium, and aluminium silicates with quartz. Some of the oxidized ore, of which there is very little, has a very interesting composition. A specimen shown to me by the ,general.manager, Mr. F. B. Stephens, consisted of hydrated arseniate of iron, orpiment, pyromorphite, lead oxide, with magnesium silicates and quartz. The ore found in the mine with a composition similar to this specimen was valued for gold contents at 60 oz. per ton. This ore is found as a small leader, which runs parallel to the main ore body, at intervals cutting through it.The ore is conveyed from the mine to the reduction works by means of a double road tram line. The mine is situated about rooo feet above the plant on a hill. The grade is so great (about I in 2) that the loaded trucks coming down are able to pullthe empty ones up, thus obviating the necessity of motive power for haulage. All that is necessary is two large grooved pulleys, fixed at the summit of the hilI, and provided with a rope-break for steadying the speed of the trucks down the hilI.

Jan 1, 1903

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds. The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldrell Counties in western Kentucky. According to the latest available statistics, this district supplied 165,960 short tons of fluorspar in 1937, compared with the total domestic production of 151,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

Early strategic mine planning includes decisions over the organisation of work and workforce accommodation. These decisions involve significant commitments that affect not only employee quality of life but also the impacts and relationships with existing local communities. Strategies for workforce accommodation are characteristically community-based (either as purpose-built company towns or integrated within existing local communities) or commuter (fly-in, fly-out) mine camps. The quality of accommodation underpins the fulfilment, morale and motivation of employees. This is not only relevant to productivity and safety, but also to recruitment and retention, particularly with the current onset of a significant human resources crisis. In the event that communities exist in proximity to a proposed mine then the accommodation strategy selected can influence the value-adding potential for the sustainable development of such communities. This early planning is particularly challenging where mine locations are isolated and/or face significant economic, social and political adversity. This paper draws upon a case study review of five large mining projects implemented in three South American countries, selected to cover a range of scenarios and accommodation strategies. The review aims to advance our understanding of the complexity of the underlying planning issues. Each scenario considered the prevailing environmental, social, economic and political situation, together with the adopted accommodation strategy. The case study review aimed to identify lessons learned and to make recommendations for advancing mineworkersÆ accommodation planning practice.

Jan 1, 2006

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By Vinit Mody

The belt conveyor is one of the major pieces of equipment for transferring bulk material in mining operations. However, considerable amount of respirable dust may be generated whenever the bulk material is loaded, dumped, or transferred. This report identifies and evaluates various dust control technolgies applicable to belt conveyors, and describes how an integrated systems approach can reduce dust emissions at a transfer point. Phase I of the program consisted of literature search and a critical evaluation of various dust control technologies. The work established that a comprehensive approach to calculating exhaust volumes for dust collection system does not exist. The parameters that affect the wet dust suppression efficiency were also reviewed. Based on the Phase I work, bulk material handling system and dry dust collection or wet dust suppression systems were designed and installed at a number of transfer points in a limestone processing facility, a surface mine selected as a field test site. Field test data were used to determine the validity of various exhaust volume calculations at the different transfer points. The field test data also formed the basis for the evaluations of the relative effectiveness of commercially available and wet dust suppression systems in controlling respirable dust emissions.

Jan 1, 1984

By Paul D. Tomlingson

Editor&apos;s note: This is the first of two articles on maintenance. Part two, "Effective maintenance downsizing techniques," will appear in the October issue of MINING ENGINEERING. Most mine managers are aware that the cost of maintenance rarely goes down unless work is done less often and with fewer people. Fewer people translates into downsizing and seldom means making maintenance more efficient. Even so, mines that have struggled unsuccessfully to improve maintenance and are now pressed to reduce maintenance costs may opt for downsizing. On the other hand, mines with an immediate need to reduce costs may be forced to downsize because they cannot wait for needed improvements to take effect. This can be bad news for maintenance. In any case, the mine must downsize correctly to ensure effective maintenance is sustained.

Jan 1, 1994

By R. J. Folic

Investigations of the vibrations of a pile in soil are performed on a dynamic model in the form of a prismatic bar of finite axial and flexural stifnesses with a discrete mass at its free end representing the cap. The soil is represented by a system of springs of constant and variable stiffnesses. Oscillation differential equations are derived by means of the Hamiltonian principle for non-conservative systems. The problem is reduced to a coupled system of two non-linear partial differential equations with corresponding initial-boundary conditions. Frequency equations of longitudinal and lateral linearized equations are formed. The paper determines natural frequenc­ies and oscillation modes. It separately examines longitudinal vibrations excitated by a hermonic force acting upon the pile cap, and lateral vibrations excitated by an impulse acting upon the cap. The results of the numerical processing are presented in respective diagrams in dimensionless form.

Jan 1, 2010

By Hermes Vilchéz

El presente texto describe los beneficios de la apertura de los circuitos de flotación como alternativa de mejora en la performance metalúrgica de las concentradoras. El trabajo se efectuó en la empresa minera Los Quenuales, Unidad Iscaycruz (Lima), modificándose los circuitos cerrados a los abiertos y encontrándose los siguientes beneficios: el incremento del tonelaje de tratamiento sin aumentar equipos en los circuitos de flotación, la mejora en la recuperación y el grado de concentrados.

Sep 9, 2007