Search Documents

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

By Pierre Lacombe

"The operation of the Louvicourt Mine will have to rely on stringent grade control and on the optimization of the amount of blocked ore made available per given development effort. All of the above being necessary to obtain the highest throughput at the lowest mining cost.To assist in achieving these objectives, the need for production of a competent fill with short curing time was recognized early by the project partners. As well, operating costs associated with the selected method should be as low as possible while meeting the technical criteria.A feasibility study comparing filling methods showed potential benefits in all aspects of the paste fill use, except for its higher capital costs and increased operational complexity. This last consideration was tackled by the conservative design approach adopted in the flowsheet development of the paste fill plant.Since commissioning of the plant has just been completed at this time, the paper will focus on the feasibility study and its background, the design of the plant and testwork results at pilot plant and plant scale.RésuméLe succès de l 'opération de Louvicourt Mine dépendra d' un contrôle serré des teneurs du minerai et de la maximisation de la quantité de minerai développée par effort uni ta ire. Ces critères devant etre respectés afin d'obtenir le taux de production le plus élevé au coût le plus bas.De façon à satisfaire ces contraintes, les partenaires du projet ont reconnu tôt la nécessité de produire un remblai de qualité tout en maintenant un temps de curage court. De plus, les coût d'opération associés a cette opération se devaient d'être des plus avantageux sans sacrifier l'atteinte des objectifs techniques.Une étude de faisabilité comparant différentes méthodes de remblayage a démontré que le remblai en pâte offre des aspects positifs sous taus les angles, si ce n'est de son coût en capital initial élevé et de sa complexité relative d'opération. Ce dernier point fut considéré de près par l'adoption d' une approche conservatrice lors de la conception de l'usine de rernblai.Puisque la mise en service de l'usine n'a été faite que les détails de l 'étude de faisabilité et ses fondements, 1 'usine et des résultats d' essais obtenus a l'échelle de l'usine seront discutés."

Jan 1, 1995

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By R. Lawrence

Mineral property valuations to be used for Canadian securities regulatory purposes must comply with CIMVal1. The technical basis for a CIMVal report is the same as that required for a technical report that complies with NI 43-1012. NI 43-101 describes the content to be covered in a technical report, while also covering other requirements, one of which is that the report should be based on a property visit. CIMVal is based on five tenets that the valuator must follow: ? Materiality. ? Independence. ? Transparency. ? Competence. ? Reasonableness. Upon its adoption by CIM Council in 2003, it was hoped that the new CIMVal code would be adopted without change by the several Canadian regulators.

Jan 1, 2011

A homely simile will serve to epitomise an interpretation of the rock structures and associated phenomena of the block of country under review, as it appears to the writer.Disregarding the many thousands of feet of overburden that have been eroded away during the ages, the present denuded surface and rock systems below may be pictured as a slab of some titanie ribbon cake that has suffered much damage from rough handling and exposure, yet retaining much of the original symmetry of its superimposed layers of variegated colour and texture.Lateral pressure has crumpled the cake into a series of irregular corrugations and, in parts, has caused some of the layers to crush and slide over their neighbours.Following upon this squeeze, the cake has been severed into segments and rhomboidal slabs by vertical cuts, and these portions have been severely jostled one against its neighbour, crushing the faces of contact and dragging the contiguous layers in the direction of movement.The variegated icing of the cake is represented by intercalated sills of amphibolite, pegmatite, and aplite, and the body of the cake by highly altered sedimentary rocks.The icing has been assailed by the rats of erosion with such effect that only residuals of the original structures remain. The body of the cake has suffered successive waves of igneous invasion in the order of lode pegmatite, followed by zine, iron,copper, and finally by silver-lead. These successive invaders found difficult access, along certain of the vertical cuts, to the more succulent layers of the cake, where, gorging to repletion, many were imprisoned and entombed for the future service of mankind.

Jan 1, 1927

By Randy Vranes

Sophisticated information technology, quality management systems and a commitment to the environment has allowed Solutia’s Soda Springs phosphate mine and elemental phosphorus plant to reduce operating costs, improve product quality and contribute to the sustainable development of Idaho’s industrial minerals. Soda Springs background The Soda Springs phosphate mine and plant is a joint venture between Monsanto and its operating partner, Solutia Inc. The operation is based in southeastern Idaho in the Western Phosphate Field. The plant is located about 275 km (170 miles) northeast of Salt Lake City, UT and about 4 km (2.5 miles) north of the town of Soda Springs.

Jan 1, 1999

Underground mine designs typically try to avoid extraction beneath streams and rivers of any significant size, especially when the overburden rock thickness between the stream bed and the mine is thin. Potential issues with mining beneath streams include excessive groundwater inflow to the mine; weak ground (roof, floor, and pillar) conditions; horizontal stress effects; as well as stream loss and other potential adverse environmental effects. However, there are times when crossing beneath a stream or river is necessary to move into a new area of mineral reserve without creating additional mine access points from the ground surface. Often, stream crossings are completed without thorough assessment, potentially resulting in increased costs, decreased safety, and, in some cases, failure to advance the mine. Selection of the most favorable location(s) to cross the stream must account for numerous factors and the associated assessment often requires a multidisciplinary approach. Stream crossing investigations often require geological, hydrogeological, geotechnical, and geophysical expertise. Phases of stream crossing investigations include desktop evaluation of maps and aerial photography, stream bed observations, drilling, detailed rock core logging, downhole geophysical surveying, hydraulic conductivity testing (packer testing), geotechnical laboratory testing, assessment, and reporting. The deliverables from a stream crossing assessment typically include geological, geotechnical, and hydrogeological characterization of potential stream crossing locations; classification of favorable and unfavorable crossing locations; recommendations for entry design and pillar sizing; and recommendations for if, and how, to conduct pre-grouting activities. Examples of technical aspects of data collection and assessment are provided based on decades of industry experience conducting stream crossing assessments in various underground mining scenarios.

Jul 28, 2020

The Bureau of Mines is responsible for a broad spectrum of programs for meeting the diverse and changing mineral resource needs of the Nation. These programs are managed by the Director and two Deputy Directors, who formulate general policy and program direction from the Washington, D.C., headquarters. A senior advisory staff, consisting of the Chief Staff Officer, Chief Scientist, and Chief Mining Engineer, provides advice and consultation to the Director on a wide range of scientific and technical matters and acts on behalf of the Director to maintain liaisons with other government agencies, mineral industries, and professional societies. Bureau program activities are classified into two major functions: (1) Developing new and improved technology that will make the production and processing of minerals more efficient, safer and more healthful for mineral workers and the public, and more compatible with a quality environment.

Jan 1, 1980

A compilation of papers presented at the Third WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 4-6, 1976. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1976

By George W. Maynard

(Pittsburg Meeting, March, 1910.) AT the Pittsburg meeting of the Institute, May, 1879, I made the first announcement in America of the results obtained by Sidney Gilchrist Thomas and Percy C. Gilchrist, ill their efforts to eliminate phosphorus in the manufacture of steel in the Bessemer converter and the open-hearth furnace.1 The first published statement in an American newspaper was a reprint of the first Thomas-Gilchrist paper, 2 which I sent to J. C. Bayles, at that time the editor. At the suggestion of many friends who were present at the Pittsburg meeting, and others who are cognizant of the beginnings of the process in the United States, and for the information of the younger generation of the iron and steel fraternity, I have thought it eminently proper that the history of the process in detail should be given where I made the first announcement and where the process has had its largest development. During my residence in England, from April, 1873, to February, 1879, and as a member of the Iron and Steel Institute since 1874, I was present at many of its meetings during those years. At nearly -every meeting the burden of discussion was the question of the use of pig-iron containing phosphorus in the. manufacture of steel by the Bessemer or the open-hearth process. In my biographical notice of Thomas;3 read at the New York meeting of, the Institute, February, 1885, I show that the working-out of the process was not a hap-hazard or accidental inspiration, but the culmination of many years of investigation of experiments and theories which had been carried on and advanced by chemists and metallurgists at home and abroad. 1 Trans., viii., .5 (1879-80). 2 The Iron Age, vol. 22, No. 17, p. 3 (Oct. 24, 1878). 3 Trans.. xiii., 785 to 791.

Jul 1, 1910

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By C. J. Allen, L. Battiston

"Introduction It has long been recognized by the hot-dip galvanizing industry that the characteristics of the galvanized coating can be influenced significantly by steel and pro cessing variables. Probably the variable of most concern to galvan izers today is steel chemistry. More specifically, the problem is the excessive reactivity of continuously-cast, silicon-bearing steels. In the past, structural steels processed by general galvanizers were in the low-to-medium ca rbon category and contained silicon at either low impurity levels (as with rimmed steels), or less than approximately 0.10% (as with semi-killed steels). The structures of the coatings produced on such steels are characterized by dense, compact layers of delta and zeta iron-zinc alloy phases and a distinct outer layer of eta zinc, which usually imparts a bright shiny appearance to the coating. The presence of silicon in steel, above the so-called semi-killed levels, is known to cause marked stru ctural changes in galvanized coatings. Such coatings are characterized by a relatively thin delta layer, a thick , coarse zeta layer and frequently an absence of the eta layer. The eta phase, comprising zinc which is carried out of the bath during withdrawal of the work, can be consumed by the continuation of the coating reactions until its temperature drops to the solidification point. This results in a dull grey and often mottled surface instead of the usually bright metallic appearance. These galvanized coatings are usually much thicker than coating specifications requ ire and they are usually more brittle and have poor adhesion to the steel. In service, these coatings tend to develop a rust-like discolouration. With the wider use of continuous casting by the steel producers and the associated additions of silicon in this process, the problem is becoming more important and receiving greater attention from the galvanizing industry ."

Jan 1, 1987

By R. L. Levens

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface area exposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 2010

By M. P. Valoski

Mine fires and/or explosions continue to occur. While these are unusual events, they comprise emergency situations. Whenever one of these events occurs, the Mine Safety and Health Administration (MSHA) responds with specially trained teams, mine fire experts, sophisticated scientific instrumentation, and trained instrument operators. In order to analyze mine air samples on-site, because time is of the essence, MSHA has a Mobile Gas Laboratory. The laboratory, which is stored near Pittsburgh, is totally self-contained. Sending air samples to a laboratory would take too long. Mine fire experts need the results of the latest analyses as soon as they are finished. The mobile laboratory is housed in the box of a diesel truck. Benches line both sides of the laboratory. Gas chromatographs are mounted on the benches. There is sufficient bench space for multiple bench top gas chromatographs. These instruments and their controllers are shock and vibration isolated to protect them during transit. The mobile laboratory can operate using on board diesel generators or line power. An uninterrupted power supply (UPS) supplies power to the instruments while switching from generator to line power or visa versa. Therefore, analysis of samples can proceed without interruption if a power failure would occur. In the rear of the mobile laboratory are racks that hold compressed gas cylinders. These cylinders contain carrier gas and compressed air. An air compressor is housed under the laboratory to operate the gas chromatograph actuators. Within several hours after arriving at a mine the instruments have stabilized and have been calibrated. The mobile laboratory is ready to begin analyzing air samples. The mobile laboratory has proved itself at many mine fires and explosions since its purchase.

Jan 1, 2009

By A. J. Farstad

The principle objective of the research effort described herein was to identify as rapidly as possible a practical trapped miner location system. Much effort has been expended in the past on the development of a highly sophisticated seismic location system [1] for trapped miners. Field tests of this system have shown that the location accuracy is limited by a combination of seismic velocity anomalies, timing errors, and in general by the relatively weak nature of the signals received at the surface. It was first felt that similar propagation anomalies would be experienced by electromagnetic systems, but to a greater extent than the seismic. However, preliminary tests performed by Westinghouse on the Operations and Maintenance Program, Contract No. H0210063 in 1971 and 1972, indicated that an electromagnetic solution to the location problem may be more feasible than a seismic solution. Thus a more concentrated effort was launched in 1972 and 1973 to more completely determine the feasibility of electromagnetic location systems for trapped miners. Two different approaches to the location problem were undertaken on this program: (1) A pulsed electromagnetic system was developed by the Special Systems Division of Westinghouse in Baltimore, and (2) a Continuous Wave (CW) System was developed by Westinghouse Georesearch Laboratory (WGL) in Boulder, Colorado. Part I of this report will deal only with the development and results of CW Location System developed by WGL. The CW Location System was field tested at three eastern coal mines and at one western hardrock mine. The maximum overburden depth penetrated during these tests was 990 feet at the Robena No. 4 mine near Waynesburg, Pennsylvania. The earth conductivity at this mine was measured to be 1. 1X102 mhos/m, which combined with the deep overburden make this mine representative of expected worst case conditions for a coal mine EM location exercise.

Jan 1, 1973

By King R. L

Low-enthalpy geothermal groundwater resources occur at relatively shallow depths in the Upper Cretaceous/1'ertiary sedimentary sequence in the on-shore Gippsland Basin. The main stratigraphic unit containing hot groundwater is the Latrobe Group. Groundwater temperatures in the range 30 to 70¦C have been recorded from depths between 500 and 1000 m. The hottest groundwater is in the Latrobe Valley and Lake Wellington depressions. Geothermal gradients in these areas range from less than 2¦C/100 m to over 10¦C/100 m (compared to a world average of about 3¦C/100 m). A number of theories have been advanced to explain the geothermal anomalies including exothermic reaction such as oxidation of coal, mixing with deeper, hotter groundwater and high geothermal fluxes along fault zones. Variations in geothermal gradients can also result from type and thickness (and hence thermal conductivities) of the sedimentary pile, depth to consolidated basement rocks, and influence of groundwater flow patterns including proximity to recharge zones. The hot groundwater in the Gippsland Basin has substantial potential as a source of energy for direct heat applications such as process heating, space and water heating for buildings, and agricultural and aquaculture. Geothermal energy has a number of environmental advantages over traditional sources of energy. It is clean, safe, causes minimal land disturbances and in most cases is naturally renewable.

Jan 1, 1992

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

Claims of 16 gold mining companies seeking damages from L-208 will be heard in Court of Claims starting Jan. 26. Earlier this year, judges ruled that 3 gold mining companies could sue for damages from the wartime order closing their mines. Congress later waived the statute of limitations thus permitting other gold miners to get in their claims. Despite power shortages third quarter production of aluminum exceeded that of the previous period by 2.2 pct. However, September production was 16 million lb less than in August. Hewitt-Robbins, Inc. dedicated a new $1 million addition to the company's Buffalo, N. Y. belt conveyor plant. New equipment, including a $220,000 press, will make belts up to 70 in, wide, compared with the former limit of 60 in. Charges of a tin cartel in Malaya are not backed up in the latest U. S. Government report according to the Malayan Tin Bureau. The U. S. mission reported that it "did not discover any evidence of curtailment of tin output by the mining and smelting industries." It noted that guerilla activity had halted exploration and expansion attempts by producers.

Jan 1, 1952

By E. J. Peuraniemi

Oxidation of chalcopyrite concentrate and two low-iron copper mattes were studied using a laboratory scale laminar-flow furnace simulating the phenomena taking place in different zones of the reaction shaft of a flash smelting furnace. In the experiments, screened fractions were fed into the furnace and sampled after short reaction time intervals by quenching them into a water film. Experimental conditions included temperatures of 1100 and 1300°C with reaction gas oxygen contents from 21 to 75 vol.%. Samples were analysed chemically for Cu, Fe and S to define removal rate of sulphur. Optical and scanning electron microscopy with EDS-analyser were used to examine the samples. In this paper, oxidation kinetics as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are viewed to closely define the proceeding of the oxidation, and, consequently, to compose a detailed model of dust formation and reaction mechanisms. Data obtained in the experiments broadens the knowledge of physical and chemical phenomena in flash reactions and serves as reference for computer simulations.

Jan 1, 2000

By K. Huttu, A. van Wageningen

"The Kittilä underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittilä achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two openpits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small openpits will mine any remaining near-surface reserves in the future.The Kittilä Mine is located in the Lapland region of northern Finland, approximately 900 km (560 miles) north of Helsinki and 150 km (93 miles) north of the Arctic Circle. With a mine life estimated through 2034, Kittilä is Agnico’s longest-life mine.The mine’s proven and probable reserves contain 32 Mt (4.7 million oz) at 4.6 g/t (0.13 oz/ st) gold. Ore has been mined from underground since 2010. The original 3 kt/d (3,300 stpd) operation underwent an expansion project to increase the throughput capacity of the mill by 1 kt/d (1,100 stpd), starting by the end of 2014.The region around the Kittilä Mine is underlain by mafic volcanic and sedimentary rocks of the Kittilä Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle’s Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between ironrich and magnesium-rich rocks lies a 100- to 200- m (330- to 660-ft) thick structural zone known as the Suurikuusikko Trend. This trend hosts the Kittilä deposit, where multiple mineralized zones have been traced over a strike length of more than 25 km (15 miles).Most of Agnico Eagle’s work has focused on a 4.5-km (2-mile) segment of the Suurikuusikko Trend that hosts the five main zones of the known gold reserves and resources. From south to north they are: Ketola, Etela, Suuri, Roura and Rimpi.The ore at the Kittilä Mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulfide minerals – arsenopyrite and arsenic-rich pyrite. Only about 4 percent is very fine-grained “free gold” (not locked in sulfide grains) and easier to extract. Most of this free gold is found in the outer, oxidized or eroded sections of the ore."

Jan 1, 2015