Search Documents

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

By C. P. Haller, S. J. Aresco

"INTRODUCTION The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heat¬ing value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the fusing temperature of ash and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions./ issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made.Analyses of the delivered coal and ""tipple"" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. Moreover, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.The Government purchased approximately 5-1/2 million tons of coal in fiscal year 1951. In connection with these purchases, the Bureau analyzed 10,700 samples. These are published for the use of Government officials and the public. A series of publications s been completed on coal analyses by States, or, where production is small in any State, by groups of adjacent States. In addition to analytical data showing composition and quality of coals of the States, the publications contain brief descriptions of the geological structure of the coal basins, typical mining conditions in the various districts, the principal economic data of the industry, and the relationship of mine or channel samples to delivered and tipple samples. The present publication covers many States but deals only with the analytical data of the coals.The technical papers published by States, with their numbers are: Alabama, 347; Alaska, 682; Arizona, California, Idaho, Nevada, and Oregon, 696; Arkansas, 416; Colorado, 574; Illinois, 641; Indiana, 417; Iowa, 269 and 706; Kansas, 455; Kentucky, 308 and 652; Maryland, 465; Michigan, North Dakota, South Dakota, and Texas, 700; Missouri, 366; Montana, 529; New Mexico, 569; Ohio, 344 (and Bulletin 499); Oklahoma, 411; Pennsylvania Bituminous, 590 (Supplement, 645); Pennsylvania Anthracitic, 659; Tennessee, 356 and 671; Utah, 345; Virginia, 365 and 656; Washington, 491 (Supple¬ment, 618); West Virginia, 405 and 626; and Wyoming, 484."

Feb 1, 1953

By Thomas. L. O.

Apart from a few sketches and incomplete maps, mainly topographical, and one or two detailed maps of placer-creeks, there is little information on the topography and geology of most of the country adjacent to the sections of the Alaska Highway in the Liard River area, particularly that part east of Kechika river. In 1943, the Geological Survey of Canada made a recon-naissance from Fort Nelson clown the river of that name to the Liard, thence up the latter to Hell Gate, and also up Beaver river for a distance of fifty miles. The whole of the area covered was found to be underlain by sedimentary rocks, not a single igneous dyke being seen. The British Columbia Department of Mines began reconnaissances near the highway both in and north of the drainage basin of Prophet and Muskwa rivers with a view to finding structures favourable for the accumulation of oil. In Liard River valley near the mouth of Smith river and at intervals from there clown to Devil' s Portage occur warm springs whose character and origin are not definitely' known, since they have not been investigated (21, p. 38A). Similar springs are said to occur at several localities over a broad belt extending from Muskwa river across the Liard to the Nahanni River country (26, p. 11). On Liard river below the mouth of Dease river, stratified sands, gravels, and clays of Pleistocene (?) age are constantly met with and in one or two places are underlain by sandy clays. The distribution of the latter, however, is very limited in the section cut by the river west of the Rocky mountains. The only range of these mountains that reaches the Liard is the high limestone ridge which approaches the mouth of Vents river from the southeast and then almost vanishes a few miles to the northwest of it (27, pp. 43-45). In general, the ranges of the Rockies in the area under consideration have been but little explored, but they are undoubtedly very largely sedimentary and, with the exception of some volcanics and intrusives on their western flanks, are probably almost entirely so. Unlike the high, deeply incised ranges in southern British Columbia, they dwindle in elevation north of Terminus mountain to low-wooded ridges separated by wide swampy valleys, and practically lose their identity between it and the Liard. The foothills, which, along the Liard, have a width of 38 miles (from near the mouth of Trout river to Hell Gate) are composed of a great series of alternating shales and sandstones, with some limestones, all folded closely together, which resemble those found in the foothills farther south (27, pp. 50, 19-20).

Jan 1, 1944

By K Gordon

A methodology for assessment and remediation of acid mine drainage (AMD) developed at the Sullivan Mine in the West Coast Region has been applied to the closed Blackball Mine, Blackball, West Coast Region. AMD from the Blackball Mine has low pH, high acidity, and elevated levels of iron, aluminium, manganese, nickel, zinc and arsenic. The AMD flows at a variable rate (36 - 101 L/s) into adjacent Ford Creek, causing an increase in acidity and trace element concentrations in the creek. To test the effectiveness of treatment with a simple limestone-based treatment system, a column leaching experiment was conducted over a nine day period. The results show effective removal of acidity, reduction in the concentrations of iron, aluminium, manganese and zinc, and production of alkalinity. To determine if this treatment method reduces the toxicity of the AMD to aquatic invertebrates, a 96 hour ecotoxicity experiment was conducted. The results show a significant decrease in mortality in the treated AMD compared to untreated. The column experiment, in conjunction with the ecotoxicity work, suggest that a passive treatment system consisting of a limestone leaching bed and an open limestone channel may be sufficient to treat the AMD from the Blackball Mine. Further work, such as large-scale treatment trials, is recommended.

Jan 1, 2004

By Rebecca Hardy

The escalating demand for coal, in addition to the steady depletion of reserves, has produced increasingly difficult mining conditions for coal mining companies within the United States, resulting in mining above or below previously mined areas. The safe and productive extraction of coal in a multiple seam environment requires specific design technology for effective mine planning. Presently, one of the most useful design approaches for multiple-seam feasibility analysis is using numerical modeling techniques. Therefore, numerical modeling programs LaModel 2.1 and Lam2D were used to determine the feasibility of mining the Herrin (No. 6) coal seam over an existing room-and-pillar mine in the Springfield (No. 5) coal seam in the Illinois Basin.

Jan 1, 2006

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

Jan 1, 1879

By Juan Lizana

El presente trabajo describe el proceso del sistema de gestión estratégica en la mina San Rafael, Puno. En este sentido, la empresa como parte introductoria de sus operaciones, ha propuesto la solución integral, donde la herramienta principal son los índices de gestión por unidades estratégicas de negocio y los índices de gestión por unidad operativa, los mismos que permitirán evaluar el desempeño de su organización frente a sus metas, objetivos y responsabilidades. En este sentido, el establecimiento de este sistema busca crear una cultura en la organización, a través del seguimiento de cada uno de los índices, permitiendo a la alta gerencia y a los demás niveles ejecutivos de la empresa hacer control de gestión, así como una reducción de los costos operativos en el Área de Mina y mejoras en los resultados de voladura.

Sep 12, 2005

By A. L. Mular

"IntroductionThe mining industry has made slow but steady progress toward the automation of mineral processing plants over the last 35 years. The stimulus to automate is associated with important economic and hidden benefits, so that today, the latest in instrumentation and technology is being employed.This chapter assesses the status of instrumentation justified economically, defines levels of control and certain fundamentals of feedback control loops, describes typical sensors employed in concentrator circuits, summarizes control strategies employed therein, and briefly highlights trends in integrated plant control.Current Status of AutomationAs early as 1948, the mining industry began to show interest in automation, probably because of its close association with the petroleum industry. By 1958, some regulatory control had been achieved in various sections of a concentrator, particularly in crushing circuits. Successes were attributed primarily to the reliability of sensors employed in the corresponding control scheme. By 1961, computers had appeared on the scene, initially, for data logging purposes.From 1958 to 1965, very few new control strategies had been implemented. Guidelines in vogue at this time appeared to be:- Install proven automation, unless a good instrumentation department exists at the concentrator.- Do not bite off too much instrumentation at one time.- Do not purchase on price alone; instrumentation must function in the concentrator environment.- Do not purchase automatic control equipment to be fashionable.Such guidelines were employed1 because of a lack of: (a) quantitative process knowledge, (b) reliable primary sensors, (c) initiative to try something new, (d) trained personnel, and (e) understanding that older concentrators could justify automation in many situations."

Jan 1, 1989

By J. P. Connell

The U.S. Bureau of Mines awarded a contract to Morrison-Knudsen, Inc., to evaluate the use of roadheaders in underground mining operations. Road-headers were found to be widely used in mines as construction support units, as development miners, and as stoping machines. However, road-headers were found to have mechanical and electrical problems, to suffer reduced productivity when integrated into the mining cycle, and to create dust problems. Also high capital costs and low utilization and avail-ability cause high amortization costs per ton. This report identifies the roadheader operating problems and offers suggestions for improved mechanical and electrical design as well as manufacturer and owner responsibilities for improved availability. The development of a complex integrated excavation and ground support sys tern is no t warranted until the roadheader itself is made much more reliable.

Jan 1, 1980

By Rapheal Trousselle

For over 5 years, Davey Bickford has been developing and testing an electronic detonator blasting system. These new-technology detonators provide more accurate timing than conventional systems that rely on the combustion speed of a pyrotechnic composition.

Jan 1, 1997

By Roberto Maldonado

El presente texto señala el proyecto de profundización en la mina Animón considerando sus características como: geología e hidrogeología, parámetros geomecánicos, niveles de producción, costos de capital y operación, eficiencia del sistema, flexibilidad para cambios en las operaciones, reservas de mineral y consistencia con el sistema de explotación. De forma que a través del conocimiento de estas y de las herramientas gráficas tridimensionales, se pueda analizar las diferentes alternativas, incluyendo condiciones que debe cumplir el proyecto de profundización, el cual abarca también los servicios auxiliares y ventilación.

Sep 12, 2005

By O. Naiker

Xstrata has modified and improved on the solid state reduction of chromite (SRC) process that was pioneered by Showa Denko in Japan and previously used at Xstrata?s Lydenburg plant. The history of pre-reduction is a long one, with the SRC process being the first and only commercially successful one prior to Premus. Krupp developed the chromite direct reduction and the rotary hearth for the pre-reduction of chromite. However, these processes have not been successfully commercialised. The are a number of significant differences between Xstrata?s patented Premus and the original Consolidated Metallurgical Industries (CMI) process. These include, the use of lower cost anthracite fines as the reductant source together with the use of unactivated bentonite as the binding agent. In addition the use of oxygen as an energy source is used in Premus but not in the original CMI process. There was a fundamental change in the operational philosophy of the process in that while the original CMI process aimed to maximize metallization of the pellets, the Premus process seeks to maximize the energy output from the kiln while still achieving the required efficiencies and hence increasing furnace output. Premus is designed to reduce electrical energy consumption, provide high recoveries of metallic oxides, and utilizes low cost reductant and energy sources such as anthracite and oxygen respectively. Due to the fact that Premus is one of the most technologically advanced and competitive processes used today in the production of ferrochrome it was the process selected for Xstrata?s new ferrochrome facility, Project Lion, that is due to be commissioned in the third quarter of 2006 in the Steelpoort Valley in Mpumulanga, South Africa.

Jan 1, 2007

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

By W. R. Crane

Mining of the red iron ores of the Birmingham district, Alabama, has _gone on energetically for the past 50 years and has created a large iron and steel manufacturing center, the only important one in the South. The district produces about 10 per cent of all the iron ore mined in the United States and 80 per cent of the Alabama output is red ore ; moreover 43 of the 419 blast furnaces of the country are in the district tributary to Birmingham and produce 7 per cent of the pig-iron output. The rapid growth of the district has been made possible by investigations that have led to radical changes in furnace practice; studies of methods by which the low-grade, highsilica ores may be treated by concentration 1 will give still greater impetus to development. The· mode of occurrence of the ore has made mining practice comparatively simple, but with the rapid extension of the workings underground and the disturbed condition of the ore bed some distance from the outcrop, conditions tend to become more difficult. Stoping, handling, support, drainage, and ventilation are all affected, sometimes favorably and sometimes adversely, by the extended workings and increased depth of cover. Should beneficiatioil make available the high-silica ores of the lower bench of the Big Seam, mining practice must necessarily be adapted to the new conditions and will be rendered more difficult as the weight of cover increases at long distances from the outcrop. The support of workings will require more attention as the weight of cover increases, and the efficient and economical operation of the mines will depend largely upon improvements in mining and handling the ore.

Jan 1, 1927

By A. R. Barnes, A. F. Newall

Keywords: Pyrometallurgy, furnace, smelting, spinel, PGM, phase diagrams As Merensky reef ores are replaced by UG2 ores, chromium levels in PGM smelting furnace feeds have steadily increased. Increased chromium levels lead to operating problems. Attempts to increase the chromium solubility in the slag by a variety of techniques create other difficulties. The authors have developed a technique for removal of the chromium spinel interface along with the matte for subsequent separation outside the smelting furnace by utilising differential solidification in the ladle. The process has been patented internationally with support from the Innovation Fund.

Jan 1, 2006

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006