Search Documents

By Charles Kocsis

Over the last few years a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell powered equipment into underground mines to replaced diesel engine powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine?s energy consumption, its associated greenhouse gas impact and also reduce a mine?s significant ventilation associated costs. Fuel cell powered equipment also has the advantage of lower noise and heat production compared to their equivalent diesel powered counterpart. The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions and minimum velocity requirements. However another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations these factors change, dispersion and buoyancy are limited; time may not be available and in non-coal mines ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical, consequently ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation such as a hydrogen leak from the fuel cell stack or its distribution system.

May 1, 2007

By D Craw

Previous studies of alluvial gold in Otago and Southland placer deposits have suggested a gold-mercury association for some deposits derived from Caples Terrane schist, whereas alluvial deposits on Torlesse Terrane basement typically have no mercury. A regional study of gold from Otago Schist vein deposits from both Caples and Torlesse Terranes has revealed the presence of both Au-Ag and Au-Ag-Hg alloys in both terranes. Au-Ag alloy (3 - 4 wt per cent Ag) is typical for gold found in most Torlesse vein deposits, and Au-Ag-Hg alloy (3 - 8 wt per cent Ag, 2 - 8 wt per cent Hg) is found in many Caples vein deposits. Au-Ag-Hg alloys are not exclusive to the Caples Terrane, however, as Au-Ag-Hg alloys with up to 4 wt per cent Hg are found in vein material from the Torlesse-hosted, HydeMacraes Shear Zone. In addition, not all Caples-hosted deposits have a gold-mercury association; gold grains from the Carrick and Invincible gold fields have no detectable mercury. The present study characterises gold compositions from various hard-rock vein deposits and has potential for determining placer-source relationships.

Jan 1, 2003

As the surface reserves are being depleted, more and more stone operators are seeking underground mining options. Stability of underground openings is a major concern for the safety and productivity. This paper relates to a field study conducted at a large underground limestone mine in Central Pennsylvania. Identification of hazards leading to ground failures and assessment of roof fall risks are important in mitigating injuries. Field observations at this mine were integrated with Roof Fall Risk Index (RFRI) mapping software recently developed by West Virginia University. The system is designed to combine field study data related to geologic factors, mining-induced damages, roof profile, and ground water influx to generate RFRI maps. The mine has adopted a proactive ground control program consisting of comprehensive examination of drilling and bolting logs; precision surveying of roof and rib; accurate mapping of cutters, falls, and geologic structures; and installation of extensometers and microseismic monitoring systems. Investment of time and resources has eliminated fatalities and lost-time injuries due to ground fall. This paper presents the geologic settings, mining conditions, ground control issues along with risk management and control techniques adopted at the study mine.

Jan 1, 2009

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

This manual provides basic practical instruction on the inspection of driven piles. It covers the essential components of pile driving, such as the pile driving hammer, hammer accessories, the pile and soil, and frequently encountered test methods in an uncomplicated, yet knowledgeable, and practical manner. Insight is given into the methods of installing the foundation, dealing with the cranes which do the lifting, the hammers which do the driving, the leads that guide the hammer and pile, the compressors which provide the external power when required, and finally prevalent analysis tools and testing instrumentation and procedures which enable you, the Inspector, to do your job. This DFI Inspector's Manual for Pile Foundations will help the Pile Inspector who has limited knowledge of pile foundations. Perhaps this Inspector has been pressed into service at a moments notice; a few helpful hints and suggestions to him are desperately needed and he can look here for the basics. It is also useful for the experienced Pile Inspector as a reference guide. However, this manual is not a detailed check list of every possible scenario and detail which could ever be encountered. There are other sources available which give more detailed descriptions (and should be consulted by the Inspector when appropriate; a list of this additional reference material is provided and suggestions made in appropriate chapters of this text). The current manual is more a brief "textbook overview" with some of the more important aspects given at least some emphasis so that the Inspector has some direction and hopefully helps to produce a safe, yet economical, foundation.

Jan 1, 1997

By R. R. Trengove

This paper is one of a series published by the Bureau of Mines on mining methods and operation practices. It describes the open-pit mining method and operations of the Kaiser Steel Corp. Eagle Mountain iron-ore mine, which is in the extreme southeastern part of California 175 miles east of Los Angeles in Riverside County. Nearest town to the mine is Indio, which is 60 miles away by an excellent highway (fig. 1). Elevations at the deposit vary from 1,400 to 3,000 feet. Figure 2 is a plan map of the Eagle Mountain iron mine. Kaiser Steel Corp. built a model camp at the mine, with all modern conveniences (fig. 3). The camp, comprising 145 homes, dormitories, mess hall, commissary, post office, and recreational facilities for 600 people, is at 1,390-foot elevation. The area has winter-resort weather between October and May, with occasional drops of temperature to 25° at night. From June to September temperatures sometimes rise to 1200 during the day. Rainfall is scant, approximately 2 inches a year, the majority of which comes as cloudbursts during the summer months.

Jan 1, 1956

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By Karl Marquis

La Mine Mouska exploite depuis deux ans certains blocs de réserve à l?aide de la méthode long trou. Même si, à priori, la méthode long trou semble rentable, le contrôle de la dilution ainsi que le respect d?un échéancier serré s?avèrent primordiaux afin que cette méthode d?exploitation puisse être justifiable économiquement. La présentation suivante fera la comparaison économique entre cette méthode et celle de chambre-magasin.

Oct 1, 2001

By G. J. Hasenfus

Although theoretical and conceptual knowledge regarding the impact of horizontal stress on underground coal mining excavations have existed since at least the mid-1900s, it wasn?t until the late 1970?s that the theory and practical understanding began to mesh. Since that time, particularly over the last 25 years of this Conference, increased empirical study, as well as advances in measurement technology, computer simulation, and bolt design, has significantly improved our understanding of horizontal stress impact, and provided coal mine operators with tools to reliably predict and manage it. This paper provides a retrospective review of some of the more important horizontal stress-related advancements made during the 25 years of Conference proceedings, particularly those for predicting and controlling horizontal stress impacts within underground coal mines. Relevant and significant CONSOL experiences and studies will be presented in context, with particular attention to horizontal stress considerations for longwall faces and gateroads. The significance of horizontal stress will also be placed in context with respect to local geology and structure, ground support measures, and mining configuration, method, and sequence.

Jan 1, 2006

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By Junji Shibata

Keywords: Synergistic effect, Solvent extraction, Nickel ion, extractant mixture Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni (II), 0.1 kg/m3 Fe (III), 0.01 kg/m3 Zn (II), 48 kg/m3 SO42-, 98 kg/m3 HPO32- and 31 kg/m3 lactic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods may be used for the treatment of this kind of solution. In this study, solvent extraction of Ni (II) is investigated by using two kinds of extractants in order to clarify the relationship between extraction equilibrium (static synergistic effect) and extraction rate (dynamic synergistic effect) for several extractant mixtures. The static synergistic effect does not take place significantly for the extractant mixtures of acidic extractants and neutral organphosphorous compounds, while a large static synergistic effect is confirmed when the extractant mixtures of acidic extractants and nitrogen-containing compounds are used. Nickel ions can be extracted in the wide pH range of 3.0-8.0 without any pH adjustment by using the several extractant mixtures. At the same time, the extraction rate remarkably increases by using the extractant mixtures of acidic extractants and nitrogen-containing compounds.

Jan 1, 2005

By Jerry C. Tien

Changes and the pace of change in China’s coal industry have been extraordinary during the past several years. At least 35 of the 94 former coal bureaus have been restructured into different mining companies and groups. Some of the more productive and efficient ones were further strengthened through consolidation and expansions. And several have even formed, or are in the process of forming, strategic alliances with utility companies, railroads, ports and chemical companies to secure additional reserves and coal sales. In addition, the improvement in coal pricing during the past two years has enabled China’s coal industry to move ahead with some needed changes. Coal mining accidents, though, remain a major concern for the Chinese government. Accidents remain high even though the government has made efforts to shutdown more than 55,000 unlicensed, unsafe small coal operations throughout the country.

Jan 1, 2003

By F F. Pitard

The optimization of metallurgical processes requires knowledge of the heterogeneity carried by constituents of interest. The common scenario, almost an industry standard, is to rely on the engineering firm who in turn relies on favorite manufacturers of sampling equipment to provide the appropriate sampling systems in the plant to perform accurate metallurgical accounting. This sequence is flawed from the beginning to the end because everything should be based on a careful understanding of the Theory of Sampling (TOS) by the company project team and their expert who invariably would suggest various approaches and different sampling systems.The necessary progressive and iterative approach should be that the company’s project team (mining or other industries) would do its home work to have a good understanding of the geometallurgy, mineralogy and texture of the ore in each geological unit so consultants and engineers would have the best information to start with. Then a reputable sampling expert would recommend which sampling systems are needed, so the company would require engineering firms to follow pre-established, non-negotiable requirements, and finally select the sampling equipment existing on the market today that is most likely to lead to accurate and precise enough metallurgical accounting.It is the author’s experience that when this necessary progressive and iterative approach is bypassed, sampling systems installed in the plant are likely to transgress the most elementary rules of sampling correctness. Invariably the argument is that the company cannot afford correct sampling systems for metallurgical accounting as suggested in the Theory of Sampling. There is nothing that is farther from the truth when later problems will develop and inevitable reconciliation difficulties with miners and geologists become daily routine with impossible answers; as a last resource the sampling expert may be called to perform a post-mortem analysis.The progressive and iterative approach suggested in this paper should be a due diligence requirement for any bank providing a loan for an important new mining project; anything less is most likely to generate unpleasant financial losses; historical, well-known examples are referred to.CITATION:Pitard, F F, 2015. A progressive, iterative approach leading to reliable metallurgical accounting sampling systems, in Proceedings MetPlant 2015, pp 78–91 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By Purushottam Kumar

Keywords: Magnetostriction, magnetic properties, Pd(Fe,Co,Ni) single crystals Fe-Pd, Co-Pd and Ni-Pd alloy systems show appreciable magnetostrictive strains that are of interest for sensor applications. These systems exhibit congruent melting minima. In this work the magnetic and magnetostrictive behavior of congruent melting Fe-Pd, Co-Pd, and Ni-Pd compositions have been examined. The alloys examined include Fe-54.9 at.-% Pd, Ni-45.4 at.-% Pd, and Co-45 at.-% Pd. The paper describes the growth of bulk single crystals of these alloys using Czochralski technique. X-ray diffractometer was used to obtain rocking curves that were used to determine the [001] crystal direction. Magnetostriction in [001] direction was measured using strain gages. Magnetic properties were measured using a vibrating sample magnetometer. Ni-Pd showed the highest magnetostriction values among the congruent melting compositions. Magnetic and magnetostrictive behaviors of these alloy single crystals are presented.

Jan 1, 2005

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By G. Wahl, H. Danilkewich, T. Mann

Developers of advanced mining projects face the challenge of how to craft a “Request for Proposal for a Feasibility Study” that will result in bids that are comparable and will lead to a successful execution of the study. Mining engineering consulting firms are challenged by “Request for Proposals” that may consist of a limited description of the Scope of Services and other items, which could present difficulties in the subsequent financing and/or development of the project. Changes in international disclosure requirements have also changed the landscape on how resources and reserves are reported by introducing new disclosure requirements and concepts such as qualified persons. This paper lays out a strategy for preparing a Feasibility Study “Request for Proposal” based on the experiences of a mining engineering consulting firm working on a diversity of projects around the world, and in light of the recent changes in international reporting standards for reserves.

Jan 1, 2002

By Augustine O. Orumwense

Ball mills are commonly used for regrinding operations in the mineral processing industry. But, in recent times, efforts are being made at the introduction of stirred mills particularly for those instances where very fine grinding is required. Media type (steel shot, glass beads, alumina balls and crushed quartz), media size, mill speed and the number of passes required to obtained the target product size are studied. The product size and energy consumption are used in the evaluation of the test results. The grinding media size, shape, density, filling ratio, mill circumferential speed and grinding time play a distinct role in product size fineness.

Jan 1, 2005

By Gennaro Di Lauro, Laura Meraviglia, Demostenes Efstratiadis, Danilo Coppe

This paper presentation regards the European Union’s project “I.C.E.A. - Identification Colors of Explosives and Blasting Accessories (Agreement number – HOME/2010/ISEC/AG/071 – 30 – CE – 0447240/00-11), submitted under the call for proposal “ISEC 2010 ACTION GRANT” of the “Prevention and Fight against Crime” Program of European Commission. The main objective of the project is to simplify counter-terrorism security measures and the procedures for visual identification of blasting devices.

Jan 1, 2015

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983