Search Documents

By Fumihiko Sumiya, Shinya Tanaka, Yukio Kato, Kenji Tanaka, Tetsuya Sawada

When explosives are heated under an acidic environment due to metal sulfide and sulfuric acidity, their decomposition temperature falls remarkably and decomposition reaction occurs quickly, and then explosives have the risk of the deflagration to the detonation transition. Heat resistant commercial explosives which can be used under conditions of high temperature of 200ºC and an acidic environment were studied. We developed the explosive composition consisted of ammonium perchlorate (AP) as oxidizer, saturated hydrocarbon oil as fuel and binder, and calcium carbonate as decomposition inhibitor. The characteristics of this explosive composition show a heat resistance over 24 hours at 200ºC, and a detonation velocity over 2,500 m s-1. This explosive composition has a cap-sensitivity at temperature higher than 100ºC. Cost effective heat resistant commercial explosives were created by the optimization of the grain size of AP as a main component, the addition of saturated hydrocarbon oil and calcium carbonate, and the control of bulk density by the addition of micro-balloons.

Jan 1, 2003

By John Vynne

Too often, a mine’s operations, including drilling, blasting, loading, hauling, crushing, processing, etc., are considered independent steps, rather then a continuous process. In fact, these are interdependent operations with each step in the process having an impact on subsequent operations. If the effectiveness of the drilling and blasting operations can be improved, they will impact the entire mining process. Some of the resulting improvements include: level benches on grade; fragmentation and diggability with the result being reduced loading times; haul cycles improvements; and the crushing and milling operations will be more efficient and less energy consumed. Thunderbird refers to this as “Drill to Mill” information cycle or process. This paper focuses on two of the technological enhancements Thunderbird has added to its drill monitors that allow the mines to impact the “Drill to Mill” concept. These enhancements are: incorporating global positioning satellites into drill monitors; and radio off-loading of data.

Jan 1, 2001

By S. A. Luciani

"In 1957, an asbestos orebody was discovered in the northern sector of the Ungava Peninsula of the Province of Quebec, an area now identified as Asbestos Hill. The deposit is situated on a plateau 1700 feet above sea level and 42 miles inland from Hudson Strait. It is a bleak, iso. lated location of typical arctic environment. Fifteen years were to pass before the first shipment of ungraded fibre was made in 1972. These years we1•e occupied with field surveys and investigations, diamond drilling, engineering design, evaluation of investment and operating costs, and construction. The problems normally associated with mine development were further complicated by location, isolation, and the extreme cold and permanently frozen ground of the arctic regions. Unique to an isolated arctic operation are the organization of support facilities and services, procurement and retention of personnel, construction of access roads and airports, and scheduling of product out and supplies in during the short summer period of sea navigation."

Jan 1, 1976

By Carlos Henrique Turolla Maia, Ulrich Maidl, Marc Comulada, Julio Claudio Di Dio Pierri

"Pure sands are typically the domain of slurry shields due to their high permeability and their granular characteristics. However, the Earth Pressure Balanced (EPB) shield machine technology has advanced in recent years with improved conditioning agents and shield machines that are equipped with slurry injection facilities and alternative mucking methods. These new so-called hybrid EPB machines have steadily increased the range of application of the EPB technology. The contribution discusses the capacities and operational features of hybrid EPB vs. slurry shield technology in pure sands. At the example of the Metro Line 4 in Rio de Janeiro (Brazil), the contribution shows that hybrid EPB tunneling in pure sands is possible and it is compared with a state-of-the-art slurry shield project as the KASIG project in Karlsruhe (Germany). Furthermore, the control of the support pressure by means of foam conditioning and slurry injection in conjunction with a close, real-time monitoring of machine parameters is discussed. INTRODUCTION Slurry shield and EPB technologies have both undergone significant developments in recent years, leading to the use of parts of one technology in the other and even to completely hybrid systems. Also the ranges of application (see recommendations by DAUB (DAUB 2010)) of both technologies have been shifted far beyond their original limits and are largely overlapping by now. Nevertheless, the basic principles of face support remain unchanged. Exploiting the possibilities of process data analysis (Maidl 2014), the interactions between the ground and the shield machine are a matter of research and have been intensely investigated. PRINCIPLES AND CALCULATION OF FACE SUPPORT PRESSURE Figure 1 shows the principles of two approaches for the determination of required support pressures: kinematic methods and numerical methods. Kinematic methods that are employed for the assessment of face stability only consider the situation in front of the TBM. The required face support force is determined by means of an assumed failure wedge that would form in ultimate limit state. Based on the ground properties, the vertical surcharge and the self-weight is transformed into a horizontal force along a virtual sliding surface. This horizontal force is to be balanced by the face support. The calculation results are amended by respective partial safety factors for water and earth pressure and the method-specific support pressure fluctuations are added."

Jan 1, 2016

By JAMES BRADLEY

THE Spanish mine is in Nevada County, California, 21 miles northeast of Nevada City by road, and 3 miles north of the town of Washington. The mill and surface buildings are on Poorman's Creek at an ele¬vation of 3,000 ft. About 35 men are employed at the property, which is producing 50 tons of ore per day. Electric power, purchased from the Pacific Gas and Electric Co., is brought in from Alleghany, seven miles away. In the early days the mine was operated by F. W. and P. R. Bradley. Between 1883 and 1899 the production was approximately $900,0)0 in gold. The ore treated during; that time yielded an average of 60 cents per ton and was mined and milled at a profit. The surface, oxidized, ore deposit was 30 to 100 ft. wide and was mined by the glory-hole method. The milling-plant at first consisted of a Blake crusher an-1 a small Huntington mill; later three large Huntington mills were added to the plant. In 1893 a new mill was built at a lower adit- It consisted of 10 stamps and four Huntington mills. The gold was secured by amalgamation, the recovery being about 50 per rent.

Jan 1, 1931

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981

By V. Sheikhzadeh, S. M. H. Haddad, M. Saghaeian, N. Esmaeili, R. Hejazi

One of the most significant features of iron ore concentrate (pelletising feed) is the specific surface area (SSA) that affects the achievement of desirable pellet properties. There are various methods to determine this parameters and currently, the most common is the Blaine air permeability method. However, due to the simplified assumptions including spherical and identical particles and 50% bed porosity, the Blain test does not provide accurate results. In fact, these two suppositions are far from reality. In this research, comparison of SSA measurement ways are investigated, containing laser diffraction testing and Blaine air permeability, on samples with different SSA, obtained from Ball mill and high pressure grinding rolls (HPGR). The output data showed that the calculated amounts of SSA by means of laser analysis were far greater than any other one. Furthermore, in the same results of Blaine air permeability tests on samples comminuted by different grinding methods, it was observed that the SSA figures from the laser diffraction method for HPGR products were almost 800 units greater than Ball mill ones. Keywords: Pelletising feed, specific surface area, Blaine air permeability, laser diffraction testing

Jan 1, 2020

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By R. J. Jewell

The storage capacity of any given tailings storage facility (TSF) is a function of the volume available for the tailings, for which the geometry of the final upper surface of the tailings is most important. One of the advantages that can be obtained from thickening tailings prior to discharge is that the tailings can be stacked at a steeper beach angle than is obtainable with conventional low-density slurries. However, there is at present no universally accepted method available for the accurate prediction of tailings beach slopes. This paper examines the current situation with the objective of putting the quest for a method for the accurate prediction of beach slopes into perspective. The paper references published reviews of the best-known beach slope prediction methods. However, there do not appear to be any independently verified projects or published references to projects on which a Class A prediction has been validated for any of these approaches, and in those instances where projects have been implemented correlation of actual with predicted slopes has been poor - often due to differences between the properties of the tailings assumed in the design and those actually achieved in the field. The author also concludes that flume-scale testing cannot be taken as a reliable indicator of full-scale performance, and suggests that the outcome of any current predictive method should be used by experienced practitioners as only one of a range of indicators in order to suggest a range of slope angles likely to result for any given operation. Practice has shown that it is possible to manipulate beach slopes by changes to the disposal technique, such as limiting the rate of discharge per discharge point and by increasing or decreasing yield stress, but the impact of these changes cannot readily be predicted. There are also newly emerging technologies, such as the injection of a polymer into the tailings at discharge, that will enhance the dewatering of tailings and hence expedite the consolidation of the tailings, that could well facilitate the development of steeper beach slopes. The overall conclusion is that with the current state of knowledge, the accurate prediction of beach slopes is not possible. Furthermore, in view of the inherent variability of the tailings parameters from any operation, it may well be of more value to concentrate on developing an understanding of the means by which the tailings parameters may be manipulated by the operators to achieve a given beach slope than to concentrate wholly on developing a generic beach slope prediction model.

Jan 1, 2012

Earnest Advocacy - A Key to Sustainable Minerals Industry Education - A Philippine Experience

Sep 13, 2010

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002

By Paul Downing

When was the last time the documents and paperwork were cleaned out of the glove boxes, door pockets, under the seats and above the visors in your company vehicles? Insurance cards that expired three years ago and vehicle registrations from 1999 through 2003, for instance, don’t do any good and just take up space

Jan 1, 2008

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By R. D. Peterson

As underground mine operations expand, the ventilation systems supporting them become complex. Complexity increases with periodic ventilation changes. New diagonal connections require a rebalance of resistance to maintain airflow in affected splits in the system. Incidents of mine fires and explosions have occurred in U.S. coal mines when diagonal connections resulting from ventilation changes have resulted in changing airflow directions. MSHA regulations prohibit the reversal of airflow and poor ventilation practice in general, but regulations cannot stipulate or recommend proactive preventative measures because every situation is different. This paper discusses the phenomenon of diagonal branches and recommends practical precautionary measures that can be taken to prevent airflow reversal in planned ventilation changes.

Jan 1, 2012

By M. Hochenhofer

Due to economic aspects and environmental regulations recycling of slag and waste from ferroalloy production became a very important issue for the companies during the last years. The treatment of slag depends prior on the composition, especially on their content of valuable metals and impurities. The final aim should be a total re-use of these materials in the industry e.g. cement industry, pig-iron production etc.. Therefore, to reach the required physical and chemical properties for a further use, possibilities of a metallurgical treatment have been investigated. The conditioning of slag with a high V-, Mo- and P-content via reducing metal bath showed to be one alternative. To determine the optimal process parameters, practical investigations with different slag compositions and thermodynamic calculations were carried out.

Jan 1, 2006

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"Abstract -The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China . The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture zone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrum in stage 1 and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to zone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999