Search Documents

By Adriane Lopes Mougo

Super duplex stainless steel presents a biphasic structure composed by ferrite and austenite with different characteristics and properties. In the micromilling process the cutting edge radius has similar dimensions to the grain size. The biphasic structure found in this material could influence on the cutting tool life and the surface integrity of the workpiece. Due to its low machinability, caused by high hardening level and low thermal conductivity, the process can produce built-up edge and high surface roughness (Ra). In this work it is performed an experimental study of the micromilling of super duplex UNS 32750 and the influence of the cutting speed (Vc) and feed per tooth (fz) on the surface integrity and tool wear. The design of experiments considered two levels and three replicates. Results indicate the increase of roughness for bigger feed per tooth, small influence of the cutting parameters on the burr formation. The tool presented flank wear after the experiments.

Aug 8, 2018

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By Edo Engel

Hot Blast Stove Technology has been developed to such an extent that low cost hot metal production for over 30 years without major repairs has become achievable, making the decision for a campaign length between 5 to over 30 years a design choice for the plant owner/operator. Some of the earlier examples of designs capable of such long campaign lengths are currently close to the 50th year of their running campaign. These examples are found especially in Europe and North America. Along the duration of these campaigns, repairs to subsystems such as burners, hot blast outlets etc. may be required. Depending on a plant’s up and down stream production capacities, the repairs may have to take place in the shortest possible time frame to minimize production loss. This article discusses an approach for intermediate repairs, executed while keeping the majority of the system at operating temperature.

Oct 30, 2017

By Detlef Ehlert

Flexibility in terms of producing high sophisticated products with an exceptional wide range of properties and dimensions requires physical based process models for the generation of optimal set points. Therefore SMS applies since many years an integrated PSC® (pass schedule model), PCFC® (profile, contour and flatness model) and CSC (cooling section control) for the use in hot strip mills, CSP® plants and plate mills offering best possible product tolerances. Focus during the development of the model was made on the best possible physical description of the rolling process to minimize the need of complex adaptation algorithms. As an addition SMS has also developed a microstructure model to ensure the quality control with respect to mechanical properties and to save up the needs of taking samples. Beside of this the modular design of the Microstructure and Material Property Model (MPM) offers additional benefits to improve the accuracy of the other models, e. g. the recrystallization model in the finishing mill. Using the results of that model strain hardening or softening effects during rolling can be predicted and an optimum pass schedule can be calculated to avoid rolling stability problems related to phase transformation.

Aug 16, 2017

By Juliano Braz Possatti, Arnaldo Carneiro Salles, Cleudson dos Santos Rego, Leandro de Lucas Mendes

The increase in customer demand for steels with higher surface requirements, associated with the need to increase ArcelorMittal Tubarão's HSM productivity, it was necessary the development of controls and actions to reduce scale losses within the scenario of high productivity. This article describes the path followed by the hot strip mill team in order to reduce the occurrence and severity of scales.

Oct 10, 2019

By Tiago Seixas Bittencourt

Technological developments, associated with the constant worry about the environmental impacts arising from industrial activity, it has driven the development of technologies and practices for efficient fumes and particulates capture arising from the manufacturing processes of steel in steel plants in general. Currently, the electric steelshops in operation with Electric Arc Furnaces (EAF), seek parameterize/design dedusting systems able to retain most of the particulates generated during melting and refining of steel in FEA through configurations of equipment, technologies and parameters operation in order to equalize the antagonistic relationship between effective fumes capture and energy balance of the EAF. The present work gets as a fundamental premise to evaluate critically the possible different settings of the usual dust removal systems, as well as their respective classical parameterizations. The work main purpose is to establish a general rule evaluation technique for dedusting system considering the different modes of operation of an Electric Arc Furnace.

Jul 30, 2018

By Sihai Jiao, Xiaoming Xia, Bo Yan

Checkered plate, which is also known as floor plate, has a raised pattern that provides excellent skid resistance for a wide range of applications, such as flooring, walkways, platforms, stair treads, covers, etc. As one of most common products, carbon steel checkered plate is used in low strength with a large thickness margin for corrosion and costs a lot in corrosion resistance treatment and maintenance. Although austenitic stainless steel checkered plate meets the requirements of general corrosion resistance, it is also hard to provide a highly comprehensive performance for its low yield strength, which mean higher thickness, higher weight, lower stability of structure. Combined the advantages of stainless steel and carbon structural steel, a roll-bonded clad checkered plate with high performance in skid resistance, high strength and corrosion resistant is developed. The metallography shows metallurgically bonded interfaces. Both external and internal bending at room temperature can be done successfully done without any cracks. The yield strength is also significantly improved. Therefore, roll-bonded clad checkered plate is superior in microstructure, strength, ductility and workability. An application case on a pulverized coal injection platform in an iron-making plant, is also introduced to show the way of processing and installation. After two years of installation on the platform, the product still keeps the original appearance. It implies that the developed plate could keep the facilities functions with much less or no maintenance and make them much safer.

Oct 1, 2019

By André de Cabral Oliveira

With the onset of the global economic crisis in 2008, and more precisely from 2009, production routes in iron making as blast furnace, sinter and coke oven, indicated a significant increase in frequency as well as intensity of undesirable incidents. The cost impact of such deteriorations of the production chain cause significant losses ranging up to several hundred million dollars annually. On the other hand, opportunities for processes improvement are contributing to enhance process efficiency and results, and also reduce or even avoid losses from unexpected incidents. The use of specialized services for processes has gained projection along the plants and emerged as an attractive alternative to increase results by increasing the performance and reducing costs and expenses. Process Services are formatted to achieve cooperative and customized solution during planned or urgent interventions, conducting feasibility studies, process improvement, training, among others, providing knowledge, information and crucial actions to preserve and optimize processes and plant facilities.

Aug 2, 2018

By Xihuai Gong, Hongshuang Di, Jianping Li, Ning Yan

In this work, we investigated the effect of the rolling process (warm-rolled or cold-rolled) on microstructure evolution and mechanical properties of 9Mn steel. After intercritical annealing at 670°C for 10min, both cold-rolled and warm-rolled microstructures are composed of ultra-fined austenite and intercritical ferrite. The austenite in warm-rolled sample includes two types of morphology, namely equiaxed and lamellar, which exhibits a wide distribution of grain-size. The incomplete recrystallization or recovery behavior of ferrite in warm-rolled and annealed sample results in higher yield strength and shorter yield point elongation. Moreover, the warm-rolled and annealed sample extends the TRIP-related work hardening over a broad strain range, resulting in a better combination of ultimate tensile strength and total elongation.

Oct 1, 2019

By Antonio Adel dos Santos, Carmos Antonio Gandra, Fabricio Mazola da Silva Paiva, Vicente Tadeu Lopes Buono

Abstract Usiminas Steel Plant in Ipatinga installed an accelerated cooling device named CLC (Continuous On-Line Control) in 2010, enabling it to supply steels produced by TMCP (Thermo Mechanical Control Process) technology. This technology complements the TMCR (Thermo Mechanical Control Rolling), with the inclusion of the accelerated cooling process after controlled rolling. There are various gains in terms of quality and productivity associated to the application of such technology. However, the flatness control for API steel becomes crucial because large thermal stresses may be generated due to thermal heterogeneity during the fast cooling when the austenite phase decomposes mostly into ferrite and bainite. In literature, there is lack of knowledge regarding a full understanding of the relation among cooling conditions and plate flatness. Therefore, this work has focused on the effect of the cooling strategy for API steels, aiming at optimizing flatness and keeping the mechanical properties within the specified ranges. The starting point was dilatometer simulation, where cooling conditions such as start cooling temperature, SCT, finish rolling temperature, FRT, and cooling rate, CR, were changed in order to evaluate their effect on microstructure. Those laboratory conditions supposed to give the best results were transposed to industrial scale, so as to produce experimental lots of plates with five different cooling strategies. It was shown the possibility to find a cooling profile that guarantees the balance between mechanical properties and flatness requirements. The influence of cooling strategy on flatness was explained by the varied heat transfer regimes occurring from hot steel surface to the ambient

Oct 1, 2019

By Kelen Juliane Mucelin

In order to better understand the tribological behavior of self-lubricating materials, Fe-Si-C matrix composites containing solid lubricants added during the mixing step were studied. The samples were produced by conventional powder metallurgy route, presenting total contents of 5%, 7.5% and 10% in volume of h-BN and graphite mixtures as solid lubricants. The composites were evaluated in terms of tribological properties, under reciprocating sliding conditions, and mechanical properties by using tensile tests. Additionally, the wear scars were characterized by Raman spectroscopy and scanning electronic microscopy. Higher total contents of solid lubricants greatly increased scuffing resistance however decreased mechanical properties. Furthermore, increasing h-BN contents reduces both properties. These results confirmed the applicability of such sintered composites as self-lubricating parts, reaching values up to 7000 N.m for scuffing resistance combined with ultimate tensile strength of 220 MPa.

Jul 31, 2018

By Bimal Nathwani

This paper presents an overview of bearings failures with focus on steel mill applications such as continuous casting, rolling mills, multi-roll cluster mills and wire and rod mills. This paper will also provide countermeasures for prevention of these modes of failures.

Jul 30, 2018

By Rodrigo Fina Ferreira

This paper presents a mineral liberation study on two iron ore samples from the Quadrilátero Ferrífero, in Brazil: compact itabirite of low-grade metamorphism (CI) and friable itabirite of high-grade metamorphism (FI). The quartz liberation spectrum for both samples have been obtained through QEMSCAN analyses, carried out for several comminution degrees, to compare the liberation characteristics and to evaluate the evolution of the quartz’s liberation degree after fragmentation. The results have shown significant differences in liberation spectrum between the itabirite samples studied. The liberation process of FI was easier than of CI, due its high porosity and larger crystal size compared with CI, which has shown more complex mineral assemblages with low porosity and smaller crystals. The quartz liberation spectrum has shown that grinding at P95 of 0.210 mm for the FI sample, and of 0.045 mm for CI sample, should result in satisfactory liberation for subsequent concentration step.

Aug 1, 2018

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By Evan Thomas

It has been shown before that liquids can slip at a solid boundary, which prompted the idea that parallel-surface bearings can be obtained by the use of alternating slip and non-slip regions in the direction of fluid flow. The amount of slip at the wall depends upon the surface tension at the liquid - solid interface, which in turn depends on the chemical composition of the surface and its roughness. In the present study a heterogeneous surface was created by coating half of a circular glass disc with a coating repellent to glycerol. A rotating glass disc was placed at a known distance above the coated stationary surface and the gap was filled with glycerol. With the top surface moving in the direction of slip to non-slip region, a pressure build up can be theoretically predicted. The pressure gradient in the two regions is constant, similar to that in a Rayleigh step bearing, with the maximum pressure at the boundary. In order to accurately measure the force generated by the pressure increase, a load cell was attached to the heterogeneous disc. Experiments were conducted by varying both sliding speed and distance, and the resultant load carrying capacity was measured and compared with theoretical calculations. This allowed the slip coefficient of the coated surface to be evaluated.

Jul 31, 2018

By Esteban Ruisanchez Rodriguez

In this paper we will discuss the process of the grain size customization of the EBT filler sand in relationship to the technical characteristics of the furnace and its tap hole. By customizing the grain size distribution, the glassy area formed on the top of the tap hole varies and supports differently the metallurgical pressure of the molten steel providing increased free opening speeds. Taylor made sand improves therefore the free opening rate, reduces the tap to tap time and increases the lifespan of the tap

Aug 16, 2017

By Enrique Francisco Somolinos Garcia-Morales

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 1, 2018

By Detlef Ehlert

Energy efficiency is coming to the center of attention in the metallurgical and rolling mill industry due to increasing energy costs, limited resources and political requirements. Also, a green image and energy efficient production is a clear competitive advantage. SMS Siemag, being familiar with automation and measurement equipment, provides an energy data management system which gives transparency over the energy consumptions. All energy relevant media including electricity, gas, water, compressed air and further more can be recorded. The system is manufacturer-independent and allows the use of already installed measuring technology with the possibility of subsequent extension. So potentials for improvement can be recognized and energy savings can be estimated and proven after the implementation of the measures. Being familiar with the processes in the metallurgical and rolling plants, the system by SMS Siemag allows the assignment of the energy data to the production and plant data. Only by this connection, the data can be reduced to key performance indicators allowing authoritative evaluation of energy efficiency. The results are clearly represented on dashboards and support the continuous improvement process. The system also supports the energy controlling with an automatic reporting system, cost center assignment and in support with certification according to ISO 50001.

Jul 30, 2018

By Javier Martinez Rubio

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 16, 2017