Search Documents

By P. M. Kelly

TWO analytical methods for calculating the positions of matrix and twin reflections on electron-diffraction patterns of a twinned cubic crystal have recently been published.1,2 Meieran and Richman1 considered the case of twinning on (1 12) in a bcc structure, while a more general treatment, capable of analyzing twinning on any plane in a cubic crystal, was developed by Johari and Thomas.2 The latter authors applied their general rotation matrix to both (111) twinning in face-centered crystals and {112} twinning in body-centered crystals and they derived separate expressions for these two cases. This separate treatment masks the fact that in a holosymmetric cubic crystal a (111) twin is crys-tallographically equivalent to a {112} twin.3 This is analogous to the crystallographic equivalence of rotation and reflection twins in centrosymmetric crys tals. A particularly simple example of this equivalence occurs when the two twin planes are perpendicular to each other—for example (111) and (112). Then, if twinning on (111) moves a point P to a new position P1, and twinning on (112) moves P to P2, P1 and P2 will be related to each other by a 180-deg rotation about [110]— the direction normal to both (111) and (112). Since there are diad axis axis along (110) direction in a holosymmetric cubic crys tal the two positions P1 and P2 must be crystallo-graphically equivalent. In other words if a particular pole (hk l) is in a position P1 after twinning on (Ill), then after twinning on (112) a pole of the type {hkl}—but not the particular pole (hk1)—will also be in the position P1. As a result, when only the general (as opposed to the particular) indices of poles after twinning are required, twinning on (111) gives the same results as twinning on (112). To convert the results for a (111) twin to those applicable to a (112) twin, when the particular (as opposed to the general) indices of poles after twinning are required, all that is necessary is to multiply the indices of the twin poles by the matrix for 180-deg rotation about [lie], i.e., The analytical methods suffer the disadvantage that a new set of calculations must be performed for each different diffraction pattern or, as is done in the Meieran and Richman treatment,1 a lengthy list of the location of the twin spots in reciprocal space must be prepared. All the tedious computation involved in these analytical approaches can be avoided by simply plotting, on tracing paper, a stereographic projection of a crystal twinned on say (112). By superimposing this twin stereogram on a standard (001) projection (preferably with the points and indices in a different color from those on the twin stereogram) the relative positions of both matrix and twin reflections can be determined by inspection. Alternatively, a composite projection can be

Jan 1, 1965

By James E. Mills

In the work of exploring certain gold-bearing gravels in the American Valley, Plumas Co., California, entrusted to my charge by Prof. A. Agassiz, of Cambridge, and Q. A. Shaw, Esq., of Boston, it became necessary to sink a shaft through loose materials containing in some layers large quantities of water, and I have been compelled to devise a new method which has proved successful and may be of service elsewhere.

Jan 1, 1885

By Sterry Hunt

The American Institute of Mining Engineers, and American science in general, have sustained a great loss in the death of Prof Benjamin Silliman, deceased at New Haven, Connecticut, on the 14th of January, 1885, at the age of sixty-eight. But a month has passed since, as one of the pall-bearers, I paid the last tribute to the remains of my old friend and honored master.

Jan 1, 1885

By Ta M. Li

This article draws freely on the experiences of the engineering and operating staff of P.T. Inco and its parent firm Inco Ltd. In addition, information was derived from papers presented during the recent International Laterite Symposium, held in conjunction with the 1979 AIME Annual Meeting, New Orleans, La., February 19-21. The author wishes to acknowledge all contributors and, in particular, Roy Aitken, president and managing director, P. T. Inco.

Jan 7, 1979

By John C. Smock

The fire-clays of New Jersey belong in two geological ages, the cretaceous and quaternary, or post-tertiary. Three very small deposits of plastic clays have been discovered within the limits of the Archæan rocks. These are not refractory and of little importance, excepting in a geological consideration. They have resulted from a decomposition of the feldspars of the rock in situ, and they have been classified as inferior kaolins.

Jan 1, 1879

By C. M. Shigley

The record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.' The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 to 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000- ooo-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation—the largest known magnesium plant utilizing sea water as its raw matcrial. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and 7 miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1949

By C. M. Shigley

Tan record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.1 The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 t0 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000000-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation-the largest known magnesium plant utilizing sea water as its raw material. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and y miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1945

By C. D. Ramsden

During the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Purchase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by salvaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a considerable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been rebuilding locomotive wheels for several years with automatic open are-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under-flux are-welding process for wheel rebuilding, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. Open Arc Welding With the open arc process, a set of wheels could be rebuilt for about 40 pet of the cost' of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or positioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1947

By C. D. Ramsden

During the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Purchase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by salvaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a considerable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been rebuilding locomotive wheels for several years with automatic open are-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under-flux are-welding process for wheel rebuilding, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. Open Arc Welding With the open arc process, a set of wheels could be rebuilt for about 40 pet of the cost' of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or positioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1947

By AIME AIME

ORGANIZATION of The Federated American Engineering Societies was effected at the organizing conference of national, local, state and regional engineering and allied technical organizations at the Cosmos Club, Washington, D. C., June 3 and 4. Thus is brought into being the greatest national engineering society in the world. The object of the organization is to further the interests of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to engineering and allied technical professions. Prominent engineers from all parts of the country, representing more than 75 engineering societies, with an aggregate membership of more than 125,000, participated in the organization. The constitution as adopted by the conference, calls for the creation of s managing body to be known as the American Engineering Council, and its executive board. The belief was expressed that the entire organization would come to be spoken of as the American Engineering Council. The council is to coordinate the activities of state councils and of local affiliations whenever these activities are of national or general importance or may affect the general interests of engineers. Representation in the council is to be according to membership of the component societies.

Jan 1, 1920

By J. F. Keefe, C. J. Bier, O&apos

This study was carried out with copper because it represents the simplest form of sintering, in that but one metal is involved and all reactions occur in the solid state. The present work will cover three variables affecting the sintering process; namely, briquetting pressure, sintering temperature and time in hot zone. Although strength and dimensional changes were observed, this is primarily a metal-lographic study of the sintering process in copper. The term "sintering" should be understood to mean the process by which the metal powder particles of the compact become united into one body. Material Used The copper powder used was made from reduced copper oxide, and is typical of a grade used for the mass production of parts formed of metal powders. The screen analysis of the powder was as follows: Per Cent Per Cent BY BY Particle Size "Weight Particle Size "Weight Mesh Microns /80.... 0.00 43/32.... 17.49 80/I00..... 32/20......16.68 100/140.... 0.34 20/10.... 23.14 140/200___ 15.25 10/5..... 4.64 200/230....... 5.00 5/0...... 0.75 230/325.... 16.70 — 325....62. 69 The minus 325-mesh analysis was made by using a Roller Air Analyzer.1,2 The apparent density is here defined as the weight per cubic centimeter of the loose, unpacked powder as measured with the Hall flowmeter. The value for the powder used was 2.57 grams per cubic centimeter.

Jan 1, 1945

By P. F. Gnirk, J. B. Cheatham

The results of combined analytical and experimental studies involving simulated multiple bit-tooth penetration into mck are incorporated into a drilling rate equation for roller-cone bits assuming rather idealized downhole conditions. In particular, it is assumed that the rock behaves statically in a ductile fashion during bit-tooth penetration and that the rock chips are instantaneously removed from the bottom of the drill hole. The general analysis demonstrates an application of plasticity theory for the rock/bit-tooth interaction to the formulation of an upper limit on rotary drilling rate. INTRODUCTION Extensive experimentation involving single and indexed bit-tooth penetration into rock in a confining pressure environment has demonstrated that the chip formation process is of a ductile, or pseudoplastic, nature at sufficiently low differential pressures so as to be of interest in rotary drilling. Coincident with the experimentation, analytical consideration has been given to the theoretical problems of single and indexed bit-tooth penetration into rock. In general, the analyses have assumed that the rock behaves statically in a rigid-plastic fashion and obeys the Mohr-Coulomb yield criterion. The quantitative comparison between experimental and calculated values of bit-tooth load required for chip formation has been remarkably good for a variety of rocks commonly encountered in drilling and at simulated differential pressures as low as 500 to 1,000 psi. Results obtained recently for indexed bit-tooth penetration indicate that the work (or energy) required to produce a unit volume of rock chip can be minimized by a proper combination of bit-tooth spacing and bit-tooth load for a given rock type and differential pressure. By utilizing this information, it is possible to formulate a drilling rate equation, at least in a preliminary fashion, for a roller-cone bit performing under rather idealized downhole conditions. In particular, through the use of characteristic dimensionless quantities pertinent to a roller-cone bit and to indexed bit-tooth penetration, interrelationships among bit weight, rotary speed, rotary power, bit diameter, rock strength and bit-tooth shape and spacing can be explicitly expressed. In the formulation of the equations, however, it is assumed that the rock chips are instantaneously removed from the bottom of the drill hole and- that the rock behaves in a ductile manner during bit-tooth penetration. In addition, the effects of bit-tooth load application and penetration by a yawed tooth at an oblique angle are neglected. Although the analysis is presented in the light of some rather restrictive conditions, it does demonstrate a method of applying fundamental rock/bit-tooth interaction data, obtained by combining the results of analysis and experiment to the formulation of a drilling rate equation for rotary drilling. JNDEXED BIT-TOOTH/ROCK INTERACTION PREVIOUS RESULTS The mechanics of bit-tooth/rock interaction under simulated conditions of borehole environment have been extensively described in a number of papers.l-ll In particular, the effects of differential pressure, mechanical properties of rock, pore fluid, bit-tooth shape and spacing, rate of bit-tooth load application and dynamic filtration below the bit-tooth have been investigated experimentally. From a sequence of experiments.1-4 it was demonstrated that, for dry rock at atmospheric pore pressure, the mode of chip formation exhibits a transition, with increasing confining pressure, from predominantly brittle to predominantly ductile. This transition

Jan 1, 1970

By F. W. Newhall

DURING the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Browns-ville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to the chairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corpora-tion, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which are presented in this paper. Acknowledg-ments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication.

Jan 1, 1934

By C. H. Mathewson, H. M. Day

The constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 2760 C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region. Preparation of Alloys The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By H. M. Day, C. H. Mathewson

The constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 2760 C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region. Preparation of Alloys The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By I. Fatt, D. N. Saraf

A method is described for measuring two- and three-phase relative permeabilities in sandstones or sand packs using a nuclear magnetic resonance (NMR) technique to determine fluid saturations. Two- and three-phase relative permeabilities have been determined on Boise sandstone using the NMR technique of saturation measurement. Three-phase relative permeability to water was found to depend only on the water saturation, whereas three-phase permeability to oil depended on both the water and oil saturations. Relative permeability to gas in three-phase flow was found to depend only on the total liquid saturation. INTRODUCTION Three-phase relative permeabilities are extremely useful in calculating field performance for reservoirs being produced by simultaneous water and gas drives. Three-phase relative permeability data are also needed for analyzing solution gas-drive reservoirs which are partially depleted and are being produced by water drive. Some thermal recovery processes involve three-phase flow which require three-phase relative permeability data for predicting reservoir behavior. Unfortunately, three-phase relative permeability measurements have rarely been made. Also, because of the scarcity of three-phase data, it has not been possible to date to relate other measured rock characteristics to the relative permeabilities with a great certainty. Leverett and Lewis,l Reid2 and Snell3 have reported three-phase relative permeability data on unconsolidated sands. Leverett and Lewis used ring electrodes spaced along the length of the sand sample to measure the resistivity of the sample which was assumed to be monotonically related to brine saturation. Gas saturation was determined from pressure-volume measurements. Oil saturation was obtained by material balance on the cell containing the sand sample. This method is involved and time consuming. Another difficulty arises from the fact that the resistivity of the sand is a function not only of saturation of brine but also of the distribution and saturation history of the brine in the pore spaces. Reid2 used a gamma ray absorption technique for measuring liquid saturation. This method has the disadvantage that total liquid saturation rather than oil or brine saturation is all that can be measured and still another method is required to determine the saturations of individual components. snel13 used a neutron bombardment method which also required a separate determination of the individual component saturations. Caudle et al.4 measured three-phase relative permeability on consolidated sandstones using vacuum distillation for determining fluid saturations. Distillation after each reading makes this technique very lengthy and time consuming. Corey et a1. 5 and Naar and Wygal 6 measured three-phase relative permeability on sandstones by the capillary-pressure method. Semipermeable diaphragm assemblies were used at each end of the core specimen to keep the water phase in the core. Gravimetric methods were used to determine fluid saturations. Sarem7 recently reported an unsteady-state method for measuring three-phase relative permeability on sandstones. This method is an extension of Welge's method8 for measuring two-phase relative permeability. Although Sarem's method is simple and comparatively fast, the assumptions involved may oversimplify the problem. Sarem's assumption, that in all rocks relative permeability to each fluid will depend only on the saturation of that fluid, seems to be rather unrealistic. Neglecting capillary effects at the end of the core is also a weak assumption. Donaldson and dean9 measured three-phase relative permeability using a method similar to Sarem's.

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

HE high vapor pressures of metals such as lead, calcium, lithium, bismuth, and magnesium at steel-making temperatures present experimental problems which have thus far rendered it almost impossible to obtain really reliable data for their solubilities in liquid iron. Many investigators have attempted to equilibrate liquid iron in the same crucible with the undissolved liquid phase of such volatile metals. The published results,l-6 although useful, are often questionable on the grounds of not being obtained under true equilibrium conditions. Such information is not always of practical value in any case since the equilibrium vapor pressure is often several atmospheres and steel is not currently made at these pressures. Solubility measurements at lower partial pressures (< 1 atm) appeared to be more practical and easier to make. These data could be used to calculate solubilities at other pressures where Henry&apos;s Law is obeyed, and to estimate solubilities under other conditions of temperature and pressure with useful accuracy. This note outlines the development of a general technique for the measurement of solubilities in systems of this kind. The method involves equilibration of the high-boiling metal at known temperatures with the vapors of a low-boiling metal at known partial pressures. Analyses of quenched samples provide vapor pressure-solubility data and make calculations of alloy thermodynamics possible. The principle involved is similar to the closed-system diffusion-transport method which is difficult to apply with most high-melting liquid metals like iron, due to closure problems. A two-zone horizontal (molybdenum wire element) tube furnace, Fig. 1, provides two constant-temperature zones in a reaction tuve (3/4 in. ID by 1 in. OD by 36 in.). A high-boiling metal sample, 9, introduced in the higher-temperature zone, is maintained at temperature T1, and a volatile metal sample, 7, in the lower-temperature zone, is held at T2. A stream of argon with 10 pct hydrogen is passed via flowmeters, 1, and mixing-drying towers, 2 and 3. through the reaction tube at a favorable flowrate and acts as a carrier gas which entrains vapor from the volatile liquid metal at a specific constant partial pressure. The gas mixture passes through a system of constrictions, 6 and 8, to the higher-temperature zone, establishes intimate contact with the high-boiling liquid sample, 9, and exits through a small condenser tube. The entire system is at (nearly) atmospheric pressure and the volume of carrier gas passed is measured with a wet gas meter. When the high-boiling sample attains equilibrium with the vapor phase, both samples are removed and quenched. Analysis of the high-boiling sample for solute content reveals its solubility for the low-boiling metal at a vapor pressure calculated from carrier-gas volume and either a) weight loss of volatile metal or 6) weight gain of high-boiling sample plus condenser (which collects the undissolved vapors). To test the capabilities of the method, liquid silver at 1403&apos;C was equilibrated with lead vapor at various partial pressures. The relatively simple Pb-Ag system was particularly suitable for uncovering experimental problems and providing the first step toward investigations with more volatile metals and more difficult combinations.

Jan 1, 1965

By W. J. Feuerstein

STRUCTURAL imperfections in crystals, in recent years, have received the attention of metallurgists concerned with single-crystal properties. Certain etching solutions cause local variations in the rate of etching at dislocations.&apos; Dislocations are expected to be preferred segregation sites for impurities&apos; and Dash" has shown that precipitation of copper occurs preferentially at edge-type dislocations in silicon. Diffusion rates along dislocations are probably higher than rates through more perfect crystalline regions.&apos; These and other phenomena which may be influenced by dislocations may be studied by revealing dislocations as etch pits. This study was undertaken to develop an etch solution for silicon crystals to reveal low-angle grain boundaries associated with dislocation arrays and also etch pits with good contour definition. Additional etches have been reported by Dash," Vogel and Lovell.T rystals were sectioned on crystal lographic planes at various angles from the growth direction for microscopic examination of the etch pits. Experimental Crystals of 75-100 g mass and 3 cm diam were oriented and cut on crystallographic planes. Crystals were grown by Czochralski technique from a quartz crucible. Lapped wafers were chemically polished in a modified CP-4 etch for 1 min (bromine was deleted from the etch solution). The polished wafer was then etched* at room temperature for 5 min. The use of larger amounts of H2O and/or CH2COOH slows the reaction. The Cu(NO3),.3H2O was added to increase the reaction rate and give more definition to the etch pits developed. Some pertinent features concerning the attack of this etch on silicon can be summarized as follows:

Jan 1, 1959

By T. O. Breitling

Two significant problems In mill design are environmental control and cost reduction. Environmental control is predicted to be 5-10% of total plant costs in some parts of the U.S. Operating and design companies will assign this new "unit operation" a place in the early flow sheets. More advanced environmental control will add to both capital and operating costs, so mill designers will strive to reduce other costs.

Jan 1, 1970

By R. H. Richards

In October, 1891,I read a paper before the Institute on a "A HandTelescope for Stadia-Work" (Bans., xx., 732), and promised to report at an early date some results showing the degree of accuracy attained with the instrument. I am now able to report on these results and also on certain improvements that I have made in the target since the first paper was read. I may say that I prefer the title, "Prismatic Stadia-Telescope," to that used in my earlier paper, for while the instrument can be used with perfect satisfaction for short sights up to, say, 300 to 600 feet when held in the hand, it is impossible to read milch longer distances without the use of a tripod, as a steady support for the instrument. Results are here given upon four combinations of prism and telescope. No. 1. A telescope made by Alvan Clark & Sons, 3-inch objective, 28 inches focal length, magnifying 60 diameters, the prism covering half the objective: Feet measured Reading of Distance reduced Reeding of rod pro by tape. the rod. to feet. portional to 100 ft. 127.66 1.1825 100 .92629 211.35 1.9585 100 .92666 326.59 3.0265 100 .92669 484.88 4.4925 100 ,92652 606.91 5.6225 100 .92641 Average,,92651 The value of this prism therefore is .92651 feet on the rod for 100 feet of distance, or 1 foot on the rod corresponds to 107.931 feet of distance. No. 2. A Bardou telescope having a 1-inch objective, magnifying 20 diameters, and a prism covering half the objective:

Jan 1, 1893