Search Documents

By T. N. Rhodin

There can be two types of films on solids, those which are stable in mono-layers and those which tend to aggregate into three dimensional structures. A great number of metal films formed by condensation onto a solid base are unstable in the sense that they will aggregate into crystals providing the atoms possess sufficient surface mobility. The crystalline structure of the film is strongly influenced by the base in many systems and, in some cases, a single orientation prevails when the force fields around the atoms in the supporting crystal are sufficiently strong.' Relatively little is available in the literature about the nature of these forces and the role they play in promoting a preferred orientation of the atoms arriving at the substrate surface. An understanding of their periodicity and magnitude relative to the surface forces characteristic of the film itself should provide insight into the critical dependence of film orientation on the nature and temperature of the substrate. In addition, this effect may be very useful in preparing samples for surface studies. The study of the physical and chemical characteristics of pure metal surfaces has been severely handicapped by the presence of strongly adherent foreign films. Furthermore, the randomness of the surface orientation has obscured interpretation of experimental results. Evaporation of metals in high vacuum onto carefully selected substrates under ideal conditions for preferred orientation appears suited to the preparation of flat, oxide-free, oriented films for surface reaction studies. Many factors influence their structure and some understanding of the mechanism of their formation is a necessary prerequisite for obtaining satisfactory surfaces for study. The dominant factors in defining film structure are film thickness and growth rate and the nature, condition, and temperature of the substrate. GENERAL ASSEMBLY The system was enclosed in an 18 in. bell jar which rested on an L-shaped neoprene gasket on a ground steel plate as indicated in Fig 1. Rapid evacuation of the system to 10-6 mm mercury was facilitated by a 4 in. manifold, 2 in. packless valve, and an extra large diffusion pump. Suitable arrangement of valves on a secondary manifold readily permitted introduction of purified gases

Jan 1, 1950

By John Croston

IN the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 9 1/4¢, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and prep-arations for rearmament in Europe and Asia acted as a further stimulus purchasing. By midsummer the situation had so improved and stocks to been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the produc-tion quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining con-tinuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 120 per pound, and since the turn of the present year has reached 170. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By John J. Croston

In the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 91/4c, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and preparations for rearmament in Europe and Asia acted as a further stimulus to purchasing. By midsummer the situation had so improved and stocks had been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the production quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining continuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 126 per pound, and since the turn of the present year has reached 17c. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By Byron W. Cheever

While engaged in experimenting with the usual methods for estimating phosphorus in iron and steel, it occurred to me that potassium chlorate might be used to oxidize the carbon, and thus avoid the tedious and vexatious evaporations necessary for successfully carrying out the usual methods. After many trials, the following plan was adopted : Take, for analysis, of Bessemer or other low-carbon steels, from 3 to 5 grammes; of crucible steel, 10 grammes; of pig-iron, 1 to 5 grammes, according to the percentage of phosphorus supposed to be present. Of iron, high in phosphorus (1 per cent.), take 1 gramme. Place in a No. 4 evaporating dish the amount of iron or steel decided upon, cover with a funnel which will just fit inside the dish, and then add gradually HNO3, (1.20 specific gravity), using 12 C.C. of acid for each gramme of steel or iron taken. (A larger quantity of acid will be required for small samples.) When the full amount of acid has been added, and the violent action has ceased, place the evaporating dish on a sand-bath, add 10 C.C. HNO3, (1.40 specific gravity), and boil till the bulk of the solution is reduced about onehalf. Then add 10 C.C. HNO3, (1.40 specific gravity), continue the boiling, and add from time to time, during the next 15 minutes, small portions of pulverized KCIO3, till about 2 grammes have been added. (If the solution shows signs of going dry, more strong acid must be added.) This will precipitate the manganese, with some iron. Sometimes it happens that the manganese does not come down readily, and more KCIO3, or further concentration, or both, will be required. The process is not complete till the manganese is precipitated, which may be known by the appearance of a dark, mirror-like deposit on the dish, at the edge of the solution. Boil the solution 5 minutes after the last addition of KCIO3, and then add cautiously (to prevent sudden explosions) 5 C.C. strong HCl. This will dissolve the precipitated manganese and iron. Continue the boiling till the chlorine is all expelled, adding from

Jan 1, 1885

By Gary P. Thomason

INTRODUCTION One may have heard about how various projects were financed or certain companies were successful in obtaining a bank loan, but there are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of debt financing sources available to finance minerals operations (see the next Chapter 11), but these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to many minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. LOAN APPROVAL PROCESS The initial stages of the loan approval process should begin long before the bankers, and the organizations they represent, enter upon the scene. The loan approval can be broken down into six stages: 1) Generation 2) Preparation 3) Presentation 4) Evaluation 5) Approval 6) Documentation As you can see in Figure 1, the bank is only directly involved in the second half of the process. The perils in obtaining financing for the smaller minerals venture are primarily in the first three stages, not the last three. The minerals venture making application for a loan can, in almost every case, improve its chances of success by carefully planning and preparing itself and the information that will be required of it in the loan approval process. Generation This first step in the process is deciding on the need for a loan. (Earlier papers in this Book and in Chapter 11 provide some guidance.) It is surprising how many ventures confuse the need for money with the need for a loan. Suffice to say that the equity investor risks both the timing of the yield on his capital and, ultimately, his capital. The lender, on the other hand, advances temporary funds which he expects to be repaid on a specific schedule with a fixed

Jan 1, 1985

By J. B. Newsom

In the Indiana limestone district, some 50 or 60 per cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of 'quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss. General Causes of Waste There are four general reasons for quarry waste: (1) the structure of the deposit, such as its shape, bedding planes, solution cavities and strain fractures; (2) efforts to quarry blocks which do not contain distinct color or textural variations; (3) the trade custom which permits purchasers to specify the size of the quarry blocks which they will buy, which is a matter of competition for business on the part of stone producers; (4) quarry methods, which cause the greatest amount of waste. Wide channeler cuts, hook holes, crooked splitting and uneven breaking on quarry floors are included in this category. Waste Due to Structure of Deposits The peculiarities of structure cannot be eliminated, but a chance for saving lies in quarrying to take advantage of them. The commercial deposits of Indiana limestone are lenticular masses from 20 to 70 ft. thick, and nearly horizontal. All of these deposits of good stone are in the Salem limestone, a bed in the sub-Carboniferous. The Salem is traversed by two systems of vertical fractures, a major system running from northeast to southwest and a minor system running from northwest to southeast. Where the stone is covered by an over-

Jan 1, 1932

By P. Barnes

It may he of interest, and perhaps of inzportance, to the members of the Institute that specific mention should be made in detail of the great value of this method of copying or photographing all kinds of tracings." Several samples are laid upon the table which may serve as illustrations of the results obtained. Some of these show slight imperfections, depending upon the character of the tracing, and upon the length of the exposure to the light, but it may be clearly seen that even a faint copy would be quite available for actual use. The process is believed to be of French origin, and has been used for many years. Special attention seems to have been directed to it recently, and its great value to engineers appears likely to be fully recognized. The manipulations required are of the simplest possible kind, and are entirely within the skill and comprehension of any office boy who can be trusted to copy a letter in an ordinary press. These particulars may be summarized somewhat thus: 1. Provide a flat board as large as the tracing which is to be copied. 2. Lay on this hoard two or three thicknesses of common blanket, or its equivalent, to give a slightly yielding backing for the paper. 3. Lay on the blanket the prepared paper with the sensitive side uppermost. 4. Lay on this paper the tracing, smoothing it out as perfectly as possible so as to insure a perfect contact with the paper. 5. Lay on the tracing a plate of clear glass, which should be heavy enough to press the tracing close down upon the paper. Ordinary plate-glass of 3/8" thickness is quite sufficient. 6. Expose the whole to a clear sunlight, by pushing it out on a shelf from an ordinary window, or in any other convenient way, for six to ten minutes. If a clear skylight only can be had, the exposure must be continued for thirty or forty-five minutes, and under a cloudy sky, sixty to ninety minutes may be needed.

Jan 1, 1879

State of California, Division of Mines, Ferry bldg., San Francisco, Calif. Walter W. Bradley, State Mineralogist. A list of publications available will be sent upon request. Bulletin 77 is a list of publications complete from 1880 to 1917 and contains synopses It is sent free. Bulletin 105, California mineral production and directory of mineral producers for 1930, brings the complete list up to date, sent free on request The Division of Mines issues principally (1) A series of Reports, (2) Bulletins, (3) Preliminary Reports, and (4) maps. The Reports were first issued biennially, later annually, and for the past few years they have taken the form of quarterly reports. The yearly subscription price for the quarterly reports is $1, payable in advance Reports and separate chapters available are Report 2, First Biennial (1892), $1, 14 (1913-1914), Chapter on mines and mineral resources of Colusa, Glenn, Lake, Mann, Napa, Solano, Sonoma, and Yolo counties, 50 cents, 15 (1915?1916), Mines and mineral resources of Butte, Lassen, Modoc, Sutter and Tehama counties, 50 cents, and Mines and mineral resources of Monterey, San Benito, San Luis Obispo, Santa Barbara and Ventura counties, 65 cents, 16 (1917-1918), Nevada County, 75 cents, Plumas County, 50 cents, Sierra County, 50 cents; 17 (1920), Mining in California during 1920, $1 75, 18 (1922), Mining m California, chapters for Aug , Sept , Oct , Dec , free, 19 (1923), Mining in California, chapters for Jan , Feb , Mar, Sept , free, 20 (1924), Quarterly chapters on mining in California (except July, out of print), 25 cents, 21 (1925), Quarterly chapters containing county reports- Jan (Sarcramento, Monterey, Orange) 25 cents, April (Calaveras, Merced, San Joaquin, Stanislaus, Ventura), 25 cents, July (Del Norte, Humboldt, San Diego) 25 cents, Oct (Siskiyou, San Luis Obispo, Santa Barbara), 25 cents; 22 (1926), Quarterly county reports: Jan. (Santa Cruz, Trinity), 25 cents, April (Shasta, San Benito, Imperial), 25 cents, July (Mann, Sonoma) and Copper in California, 25 cents, Oct (El Dorado, Inyo) Minarets District, 25 cents, 23 (1927), Quarterly county reports- Jan (Contra Costa), 25 cents, April (Aniador, Solano) Bibliography of clay

Jan 1, 1933

By Edgar S. Cook

At the close of the Bethlehem Meeting, the writer was experimenting with large fuel-charges, 4000 Ibs. basis, as compared with 2000 Ibs., hot had not made sufficient progress to draw any safe conclusions. Previously me had always used 2000 Ibs. fuel, the ore-burden being proportioned to this as a basis. I could never persuade myself that there was any advantage to be derived from following the more popular method of larger fuel-charges. Our men were accustomed to the old way of filling ; and we did not care to run the risk of the errors likely to follow any alteration in routine work, particulary as I could not, by my course of reasoning, discover ally compensating gain. Nevertheless, after reading Mr. Gordon's discussion of Mr. Birkinbine's paper, '' Operations of Warwick Furnace from August 27th, 1880, to September 1st, 1885" (Transactions, xiv., 833), I determined to test by actual experiment the value of large fuel-charges : the change was made in the week commencing March 28th, 1886, and continued until July 25th, about four months. The fuel and ores remained during the trial the same as had been used before, and have been used since. For the first two weeks, the furnace worked with great regularity, giving excellent results, exceeding those of the two weeks immediately preceding. But for my remembrance that the furnace had on former occasions worked with equal uniformity for longer periods without any apparent reason, I should doubtless have concluded that this improvement was due to the different method of filling and congratulated myself that a means had at last been found to prevent inconvenient "dirt" accumulations. Before abjuring my previous skepticism, however, I resolved to pursue the trial further. The fourth meek developed the peculiar conditions that had prevailed previous to the change; and these continued with more or less frequency during May, June and July. At last, finding no improvement over the smaller charges—no change in fact for better or for worse—I commenced filling the 2000 lbs. fuel-charge in the latter part of July, and have continued it up to present writing, September 4th.

Jan 1, 1887

By Theron Wasson

Michigan has had another record year. Its production has been maintained by the development of fields discovered in 1938. Two minor fields were listed as discoveries in 1939. These are in the southwestern part of the state, where the greatest drilling activity took place. During the year 1465 tests were completed, of which 828 were oil wells, 56 gas wells and 581 dry holes. The four southwestern counties—Allegan, Ottawa, Kent and Van Buren—had 1077 tests drilled, while nine other southwestern counties had 70 tests, making a total of 1147 for this part of the state, 78 per cent of all drilled during the year. Michigan's production of 23,400,000 bbl. during 1939, equal to an average daily production of 64,110 bbl., exceeded 1938 by 4,655,000 bbl., thus establishing another annual record, which brought the cumulative amount for the state to a little over 125,000,000 barrels. A map showing location of Michigan oil and gas fields was published in the TRansactions in 1939 (Vol. 132, p. 353). Active Oil Fields.—The Walker field, near Grand Rapids, Kent County, had a rapid development during the year. Traverse limestone production was discovered here in September 1938, and development has been rapid during 1939. At the end of the year 5500 acres have been proved by drilling. The Traverse limestone is found in Walker field at a depth of about 1810 ft. The Temple field, Clare County, was the most active in Central Michigan. Its production is from the Monroe dolomite at a depth of 3890 ft. In this field 2500 acres have been proved by 125 producing wells. Michigan's largest producer for 1939 was drilled in the Temple field, with a rated potential of 8760 bbl. per day. The Wise field, Wise township, Isabella County, discovered in 1938, had a steady and orderly development because the operators agreed on a staggered 20-acre spacing program. So far 760 acres have been proved for production from the Dundee limestone, found at 3650 feet. Active Gas Fields.—The most active areas in which drilling was done during the past year for gas were the Freeman and Lincoln fields in Clare County, the Clayton field of Arenac County, and the Home field of

Jan 1, 1940

By Theron Wasson

Michigan has had another record year. Its production has been maintained by the development of fields discovered in 1938. Two minor fields were listed as discoveries in 1939. These are in the southwestern part of the state, where the greatest drilling activity took place. During the year 1465 tests were completed, of which 828 were oil wells, 56 gas wells and 581 dry holes. The four southwestern counties—Allegan, Ottawa, Kent and Van Buren—had 1077 tests drilled, while nine other southwestern counties had 70 tests, making a total of 1147 for this part of the state, 78 per cent of all drilled during the year. Michigan's production of 23,400,000 bbl. during 1939, equal to an average daily production of 64,110 bbl., exceeded 1938 by 4,655,000 bbl., thus establishing another annual record, which brought the cumulative amount for the state to a little over 125,000,000 barrels. A map showing location of Michigan oil and gas fields was published in the TRansactions in 1939 (Vol. 132, p. 353). Active Oil Fields.—The Walker field, near Grand Rapids, Kent County, had a rapid development during the year. Traverse limestone production was discovered here in September 1938, and development has been rapid during 1939. At the end of the year 5500 acres have been proved by drilling. The Traverse limestone is found in Walker field at a depth of about 1810 ft. The Temple field, Clare County, was the most active in Central Michigan. Its production is from the Monroe dolomite at a depth of 3890 ft. In this field 2500 acres have been proved by 125 producing wells. Michigan's largest producer for 1939 was drilled in the Temple field, with a rated potential of 8760 bbl. per day. The Wise field, Wise township, Isabella County, discovered in 1938, had a steady and orderly development because the operators agreed on a staggered 20-acre spacing program. So far 760 acres have been proved for production from the Dundee limestone, found at 3650 feet. Active Gas Fields.—The most active areas in which drilling was done during the past year for gas were the Freeman and Lincoln fields in Clare County, the Clayton field of Arenac County, and the Home field of

Jan 1, 1940

By J. R. Cahoon, W. V. Youdelis

In a previous communication by one of us,1 a theory of inverse segregation was presented by which the maximum segregation and segregation distribution throughout a unidirectionally solidified, binary-alloy ingot could be calculated. The theory, which is based on the mechanism of volume contraction and interdendritic flow, quantitatively accounts for the observed maximum segregation in the A1 (rich)-CU' and Al-Zn2 alloy systems, and for the segregation distribution along the ingot lengths for the A1-Cu system.''4 One of the drawbacks to a more extensive use of the segregation equations is their complexity, particularly for the calculation of the segregation distribution throughout the length of the ingot, involving long tedious numerical calculations to obtain the segregation. Computer pro- grams, written in Fortran II for use on an IBM 1620 computer, have been developed by the authors (and are available from them), providing quick and accurate methods for the determination of the theoretical maximum segregation in any binary-alloy system, and also for the segregation distribution in any unidirectionally solidified binary-alloy ingot. The segregation distribution is controlled by the lengths of the various solidification zones'74 which are in turn controlled by the cooling rate, and are determined from temperature-distribution curves obtained during solidification. The theoretical segregation distributions shown in Fig. 1 illustrate the effect of the zone lengths on the distribution Curve 1, indicative of a slowly cooled ingot, represents an ingot having long solidification zones, while Curve 2, indicative of a rapidly cooled ingot, represents an ingot having relatively short zones. Although these distributions are calculated for an A1-10 pct Cu ingot, the shape of the distribution would be similar for any binary-alloy ingot. These curves show clearly why early workers obtained results which indicated that the maximum (chill-face) segregation approached zero at very fast cooling rates.3 Actually, the maximum segregation is independent of cooling rate,' but even at short distances from the chill face the amount of segregation drops considerably, particularly in a rapidly cooled ingot, making it very difficult to establish the amount of segregation occurring at the chill-face. The authors would like to thank Dr. J. A. Goldak for his assistance in the preparation of the programs. The financial assistance of the Steel Co. of Canada and of the National Research Council of Canada in the form of Scholarships to one of us (J. R. Cahoon) is gratefully acknowledged.

Jan 1, 1964

By S. J. Leach

The possible solution of some of the problems raised in H. L. Hartman's article "Determining Ventilation Requirements for Continuous Miners," which appeared in the March 1962 issue of MINING ENGINEERING, is offered by recent investigative work done at the Safety in Mines Research Establishment, Ministry of Power, Sheffield, England. Highlights of this research are outlined here. Accumulations and layers of methane form in a mine roadway because it is difficult to mix methane with air beneath it by turbulent diffusion. Such mixing involves work contrary to buoyancy forces. In specifying requirements for good ventilation it is not, therefore, sufficient to state that the airflow must be turbulent in the absence of methane. Fundamental work at SMRE on the behavior of methane roof layers has led to the formulation of rules for controlling methane roof layers which specify the ventilation velocity needed to ensure adequate mixing in terms of the rate of flow of methane into the layer (V = cu ft per min) and the airway width (D = ft). A "layering number" for methane and air has been defined by [U37/V/D] where U is the mean ventilation velocity in ft/min in the upper half of the airway. In a horizontal airway there is no mixing by turbulent diffusion for values of the layering number less than about 2, resulting in extensive roof layers. But with a layering number of 5, the layer is "brought under control"-i.e., a further increase in the layering number will shorten the length of the layer only slightly, and a small decrease in the layering number will cause only a small increase in the length of the layer. In a sloping roadway with uphill ventilation, higher values of the layering number are needed to achieve this "controlled" condition; the values range from about 5 at small slopes to about 8 at a slope of 1: 10. In downhill ventilation it is possible for layers to "back" against the ventilation, i.e., to flow uphill. The critical condition for preventing backing can also be expressed in terms of the layering number. Backing will be prevented if layering numbers are about 3 for small slopes and about 4.5 for large slopes; these values for downhill ventilation also give good control of the layer.

Jan 10, 1962

By H. M. Kraner, R. C. Devries, K. H. Gee, E. F. Osborn

On the basis of liquidus measurements in the system COO-Mg0-Al2O3-Sio, and previously published data, diagrams have been constructed at 5 pct Al2O3, intervals from 5 to 35 pct Al2O3,. Liquidus temperatures and primary phase fields are shown. The optimum composition of a blast furnace slag for a given alumina content is indicated. At the optimum point, ordinary slags will be entirely liquid and will have maximum desulphurization potential and minimum viscosity. The relation of optimum composition of slags to the "plateau region" of the liquidus surface, and the application of these data on synthetic quaternary slags to actual slag compositions are discussed. Index of refraction of glasses is given as well as composition, temperature, and phase data for each mixture. THE usual blast furnace slag, as a first approximation, can be considered a mixture of the four oxides, CaO, MgO, Also,, and SiO,. Systematic, extensive data for the quaternary system, CaO-MgO-A1,0,-SiO, is therefore required for the understanding of the properties of such a slag as a function of composition and temperature. With sufficient data, it should be possible to fix unequivocably the relative amounts of lime, magnesia, and silica required for a given alumina content to result in a slag composition having optimum properties. Other constituents, such as FeO, MnO, Ti02, and S, have an effect on the properties of a slag, but as long as they are present in small and approximately constant amounts they produce only a second-order effect superimposed upon the major changes in properties of slags determined by the relative amounts of the four major components. Viscosity and desulphurization data have been reported for mixtures approaching blast furnace slags in composition, but systematic liquidus data have not been obtained. Inasmuch as a slag must be all liquid in order to be most effective as well as practicable, clearly the temperature above which a mixture is all liquid (liquidus temperature) is a type of data needed. Such data have been obtained through the study of 446 compositions and are pre- sented in this paper along with a discussion of their bearing on the optimum composition of blast furnace slags. For an orderly presentation of the data, the quaternary system is viewed as a tetrahedron with one component at each apex. Fig. 1 shows a tetrahedron representing the system Ca0-Mg0-A1,0,-Si0,. The base is the ternary system Ca0-Mg0-SiO,, A1,0, is the top apex, and the front face, the system CaO-

Jan 1, 1955

By A. J. Langhammer

A. J. Langhammer.—That is rather asking a question of the wrong man. However, I will reply to the question from our point of view. There is a considerable amount of iron powder available but the properties vary over a wide range. Powder metallurgy has progressed to the stage where we recognize certain requirements in powdered iron, and what may be a good powdered iron for one application will not necessarily fit the picture for the next one. Further, I believe that there is room for great improvement in the properties of powdered iron. Also, that there is only a limited quantity of powdered iron available having certain specific properties in which we are at the moment interested. F. P. Peters.—May I have a word? With all possible respect to the contributions of the Chrysler Corporation (and they have been tremendous) to the war effort, I think it is easy to get from part of Mr. Langhammer's discussion a false impression of vaster possibilities than really exist. It would be well if in addition to Mr. Langhammer some other manufacturers of machine parts' might tell us in the next few minutes some of the limitations they have found. For example, what is the maximum tensile strength that is being produced in a commercial part in production today? And what is the actual size limitation on bearings that are in operation and are standing up well? We should always bear in mind the fact—and I think Mr. Langhammer will agree with me— that quoting on a particular part does not necessarily mean placing it in production. In many cases it may be several months before the quotation is resolved and we know whether the part can be made. Let us open up this thing for a little free-for-all discussion of some of the ceilings that do exist in the design of machine parts made by powder metallurgy. The ceiling is not unlimited, and Mr. Langhsmmer will agree with that, 3 am sure. H. Hendriks.*—I do not think that there is so much limitation in the making of powder metallurgic manufactured parts as mentioned. Last year we had the problem of making dies for a special machine used in the manufacturing of slide fasteners. This part was wearing out very fast. It was very hard to make, it had to be hobbed out of a special steel and it was a difficult thing to manufacture in general. The tolerances were one half of one thousandth of one inch on all dimensions. We submitted this die to a manufacturer of powder-metal parts. He thought that it was impossible, but we were not as skeptical as he was and decided to try it anyway. The Canadian General Electric Carboloy Division, in Toronto, gave us then the design for the dies, which we made to their specifications. When the first part was delivered, we submitted it to our Inspection Department and its check showed that all the tolerances were right on the dot. They delivered I9 parts of exact specification, then they went off the beam; they could not keep to the tolerances. It took them a long time to get back again. We do not know what happened, but the main point I want to' make is that if a problem is attacked in the right may, the dies are made right and corrected as to dimensions found out by experiment, I do not think that there is so much diffculty in making powder-metal parts to close tolerances.

Jan 1, 1945

By G. Carman Ridland

IN conjunction with a geological investigation of the silver-bearing veins at Contact Lake, Northwest Territories, Canada, a survey was made with a Geiger-Müller counter of the gamma-ray emissions from the rocks in the vicinity of the mine workings. Discontinuous pitchblende veins have been encountered occasionally in the silver-bearing fissures, and the geophysical survey was undertaken with the hope that abnormally high gamma-ray intensities, if detected, might lead to larger and more continuous pitchblende discoveries. Before the instrument was used at Contact Lake, preliminary tests were made, first with laboratory specimens at Princeton University, and later over known pitchblende deposits at the Eldorado property, LaBine Point, N.W.T. The Geiger-Müller counter, as adapted for field use, is described; the technique of transporting and operating the instrument is outlined; and the general precautions to be observed are discussed. The results obtained at Great Bear Lake show that the instrument is capable of detecting not only a pitchblende ore shoot in a shear zone, but also the mildly radioactive "host rock" at a considerable distance from the ore body. Hence, use of the Geiger-Müller counter is urged, not just for the detailed search for an ore body in a shear zone, but for the detection of possible radioactive "host rocks" in large-scale reconnaissance surveys of unexplored regions made by prospectors and members of federal geological survey parties.

Jan 1, 1943

By Enrique Touceda

The question as to the proper amount of total carbon that the malleable founder would prefer to have in pig iron for use in the production of air-furnace, white iron castings, must be considered from different angles, that is, whether it is desirable or advantageous from an economic standpoint to use some kind of low-carbon scrap on his mixture, or make use of pig and sprue only. Whereas silicon is the acknowledged scrap carrier in the case of cupola gray iron castings, carbon performs this role for the most part in malleable iron practice, irrespective of the character of furnace used for the production of the white iron castings. In this particular, the advantage lies with the maker of gray iron castings in that the silicon content in pig iron through a regulation of furnace temperature is under very easy control by the blast-furnace manager, whereas he has little or no control over the resultant percentage of carbon, as this is dependent on the quantity of coke in the hearth, and hearth temperature, coupled with the amount of hearth slag and its particular composition. As perhaps more than 95 per cent. of white iron castings are made in air furnaces the following statements are intended to cover that situation particularly: In the malleable process the composition of the hard iron castings (that is determined upon as best suited for the work in hand) is the one factor that must control the composition of the mixture to be used; because if the elements are not between certain definite limits individually and collectively the annealed or finished product will be unsoitable, due, perhaps, to lack of sufficient strength or because it is too hard, to machine easily. The annealed product can be divided into two classes, one of which greatly predominates, that is, by far the largest tonnage is used for machine parts where high strength and ductility are essential requisites, while a far smaller amount, light in weight and thin in section, is used for other manufactured products in which castings of any reasonable degree of strength and ductility have proved satisfactory.

Jan 1, 1927

By H. Matlock

Beam-columns with continuous or discontinuous transverse and angular loads and elastic restraints are represented mathematically in a manner corresponding to finite-element mechanical models. Solutions for linearly elastic cases are accomplished by direct recursion-equation elimination of unknowns, and for cases involving nonlinear loads and supports, by repeated trial-and-adjustment of complete elastic-type solutions. Five practical applications are presented by which various capabilities of the general method are illustrated. The examples include simulation of a pipeline launching and the bending and collapse of a conductor pipe in deep-water drilling operations. INTRODUCTION The diversified and complex operations being conducted in support of the production of offshore oil have produced a wide variety of new problems in structural mechanics. Many of these problems cannot be solved by conventional analytical or experimental approaches and have therefore stimulated inquiry into new methods of solution. It is the purpose of this paper to give a brief description of an analytical method for solving nonlinear beam-column problems and to illustrate the generality of the method by applying it to several problems related to offshore operations. Although the data for all of the examples are artificial, the cases discussed will be recognized as being based on actual situations. DESCRIPTION OF METHOD The analytical approach which is to be described stems from research on offshore foundations, in particular, the study of lateral-load behavior of foundation piles. The method represents a generalization of a technique which was suggested by Gleser' and extended by Focht and McClelland2 and Reese and Matlock." To maintain generality and therefore versatility in the method, a considerable variety of input data is considered. Fig. 1 illustrates the various types of loads and restraints which might be applied to a short segment of a beam. Each of the terms illustrated in the figure is shown acting in a positive sense. Capital letters are used to designate concentrated quantities whereas the corresponding lower-case symbols indicate effects which are distributed in some way along the length of the beam. The transverse loads and the elastic restraints may be divided into two classes: (1) loads Q and q and springs S and s, which act normal to the axis of the beam, and (2) couples T and t and rotational springs R and r, which act in an angular sense. In addition, there is an axial force P which may be constant or may vary along the length of the beam. The bending stiffness of the beam (the product EI of the modulus of elasticity and the moment of inertia) is designated by the symbol F. The assumptions of conventional elementary beam theory provide the basis for the present method. Among these are the neglect of shearing and axial deformations and the limiting of consideration to straight beams of symmetrical cross-section. Lateral deflections are considered to be small compared to original dimensions. A deformed element of such a beam is shown in Fig. 2a. The curvature of the beam is approximated by the second derivative of the deflection y with respect to distance x along the beam. It is assumed that the material of the beam is linearly elastic and therefore the relation of Eq. 1 between curvature and bending moment M is the ordinary expression from elementary beam theory. A generalized beam element is shown in Fig. 2b. The element has been deflected in a positive direction by an amount y and tilted through a small positive angle dy/dx. The various loads and elastic restraint reactions are detailed in the figure. Temporarily, only distributed effects are considered; provision for concentrated loads and restraints will be made subsequently. Eq. 2 in Fig. 2b is obtained by summing the forces and moments acting on

By Bryan J. Travis, Thomas L. Cook

INTRODUCTION Our growing concern for adequate and secure sources of energy and minerals has stimulated vigorous exploration for new sources, research toward a better understanding of geological processes, and development of new extraction technologies. The need for control, or at least prediction, of subsurface fluid flow is important for many of these technologies for example: primary, secondary and tertiary recovery of oil; ground water and waste management; in-situ fossil energy extraction (oil shale, coal, tar sands); and solution mining of uranium, copper and other minerals. These technologies, especially the last two, are characterized by highly complex systems. A partial list of the physical processes occurring would include flow in porous/fractured media, multi-phase and multi-component flow with heat transport, chemically active fluids and soils, tracers, diffusion and dispersion, fracturing and dissolution. A great deal of understanding of how these processes behave and interact can be obtained from models. MODELS Theoretical models are valuable because they: 1) provide a frame of reference for interpreting results of laboratory and field experiments; 2) once validated by experiments, allow a variety of geometries, injection/production strategies, etc., to be examined (at relatively low cost) for efficiency and stability; 3) can provide guidance to the design of experiments and field operations. Most models are based on the fundamental principles of mass, momentum and energy balance. But from this starting point, many paths can be taken. For example, there is the theory of Payatakes (1973) which concentrates on the microscale dynamics. In this approach, the rock or soil matrix is represented by a complex of characteristic channels (such as periodically constricted smooth tubes). Detail of flow within the characteristic channel is calculated very accurately. A difficulty with this model is that description of a representative channel can require several parameters which may not be easily measured. Also, it is not clear how the channels can be combined practically to model a large scale flow. Another type of model is the "global" one described by Bear (1972). Here, the continuum equations for conservation of mass, momentum and energy are averaged over a distribution of pore channels, resulting in a set of conservation equations in which the small scale structure of the medium is replaced by quantities such as porosity, permeability, dispersion coefficients and tortuosity. This approach allows computation of large scale flows. However, additional constitutive equations are needed which relate averaged quantities such as permeability to observables such as local saturation, particle size distributions, and others. An important difference between models is the way they handle the momentum equation. Payatakes' model solves the full equation. In others, it is replaced by a simpler relation such as Darcy's law (valid for slow flow rates) or by Forchheimer's equation which extends Darcy's law to higher flow rates. These simple relations can nevertheless match a great deal of experimental data (Dullien 1975). The permeability term which appears in Darcy's law and in Forchheimer's expression has been related to other quantities such as porosity and particle surface area. The Kozeny-Carmen equation is a well-known example, valid for some ranges of porosity and particle sizes and for some materials. Several other semi-theoretical, semi-empirical formulations have been devised, none of which are entirely satisfactory. One goal of researchers has been the ability to predict permeability of a porous material from basic measurable quantities such as grain size distributions without recourse to adjustable parameters. This effort has proceeded from consideration of distributions of idealized, non-intersecting channels, to intersecting channels, to consideration of both distributed pore radii and pore neck radii. This last approach has been used successfully to predict permeabilities (ranging over several orders of magnitude) in sandstones (Dullien 1975). Additionally, studies on explicit networks of channels (e.g., Fatt 1956) and percolation theory (e.g., Larson et. al. 1981) have been used to examine interconnectivity effects in porous media with the hope of eventually being able to predict permeability accurately. To be of more than theoretical interest, a model must be compared s controlled laboratory conditions where boundary and initial conditions and relevant material properties can be accurately determined. Also, extraneous forces can be eliminated so that the interactions between processes of interest can be clearly seen and flow models can be vigorously tested. In contrast to the well-defined environment and

Jan 1, 1982