Search Documents

By A. Manganwidjoyo, W. A. Wiebenga

The aim of this paper is to disclose some of the correlations between rock parameters, hidden in Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks," 1956. The empirical relations concern dry rocks of varying porosity. Curves and equations interrelating the specific gravity, compressive strength, bar velocity, and Poisson's ratio are presented. In 1956 Wuerker published his "Annotated Tables of Strength and Elastic Properties of Rock", in which various physical properties of rocks determined by different authorities, are tabulated systematically. The tables are primarily intended for use by mining-, quarrying- and ore-dressing engineers. Since the list of measured parameters for each type of rock includes properties such as — grain size, specific gravity, porosity, compressive strength, static elastic cons:ants (moduli of elasticity, rigidity, specific damping capacity and longitudinal bar velocity) the tables are also of considerable interest to the practical geophysicist. Correlations between rock parameters may enable geophysicists, geologists and civil engineers to transiate measurements from one parameter to another. Even if these translations are of limited accuracy, or valid only within certain specified ranges, they often serve a useful parpose. The aim of this paper is to disclose some of the correlations between rock parameters concealed in wuerker's Tables. Throughout this paper the following symbols and units are used unless otherwise stated: Sg is Specific gravity, the ratio of the density of a specimen to the density of water at 4°C. P is Porosity, in %, the ratio of the volume of voids in a specimen to its total volume. CS is Compressive strength in 1000 p.s.i., the stress under which a specimen will fracture when undergoing a standard compression test. V is Bar Velocity in kilo-feet/sec, the velocity of longitudinal seismic waves measured in a slender bar type specimen. Vc is Bulk or Constraint Velocity in kilo-feet/ sec, the velocity of longitudinal seismic waves measured in a very large specimen.+is Reciprocai bar velocity in millisecs/ft (1 millisec = 10-3 sec). cis Poisson's ratio, the ratio of the lateral to longitudinal strain of a body under longitudinal stress. CORRELATIONS Specific Gravity (Sg) vs. Porosity (P) Figure 1 is a diagram illustrating the relatiooship between specific gravity and porosity for approuirr~ately 70 samples of dry rocks. A curve fitted by estimation to this data yields the empirical formula: Sg =-0.0268P + 2.67 * 0.2 (1) Considering unit volume of a porogs specimen then

Jan 1, 1961

By S. J. Matas, R. F. Hehemann

The existence of two distinct forms of bainite—upper and lower bainite—in hypoeutectoid steels is confirmed by a systematic study of the structure of the product resulting from this mode of austenite decomposition. The transition between these two forms occurs at about 650° F regardless of the alloy content of the steel and their structural differences can be interpreted in terms of the kinetics of carbide precipitation from supersaturated ferrite. In the past few years, a renewed interest has been displayed in the kinetics and mechanism of the bainite reaction in steels. Several rather divergent models for the transformation mechanism have evolved from these studies,'-' however, it is difficult to evaluate these models critically on the basis of the existing experimental data. In particular, a more detailed knowledge of the structure of bainite should be helpful in providing a framework for the construction of an appropriate model. Metallographic studies7-l4 have led to a recognition of at least two distinct forms of bainite—frequently termed upper and lower bainite. Although the morphology of bainite changes with reaction tem- perature, there appears to be a relatively sharp transition between the two forms. This occurs in a narrow temperature range near 650° F. Transformation at temperatures below about 650° F results in the presence within the bainite of small plates of carbides oriented at an angle of 60 deg with respect to the direction of growth of the plate, while at higher temperatures carbides are oriented parallel to the growth direction. There is no generally accepted view regarding the significance of this structural transition. Some authors feel that carbides precipitate from austenite at all reaction temperatures1' while others claim, at least for low-temperature bainite, that carbides precipitate from supersaturated ferrite.14.15 It was recognized many years ago that the nature of the carbide in bainite depends on the reaction temperature. The carbide hase in upper bainite is unmistakenly cementite.16-19 The exact nature of the carbide in low-temperature bainite is less certain. Magnetic measurements of lower bainite reveal no cementite Curie point21'22 and dilatometric studiesz0 produce total expansions which are larger than those predicted on the basis of a ferrite-plus cementite structure. These effects have been attributed to the

Jan 1, 1962

By G. Ansel, J. P. Doan

THE important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holub1-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength, and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British. Patent 5111376 relates to the parent discoveries of Sauerwald, Eisen¬reich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature" has been found to the particular characteristics of wrought Mg-Zn-Zr alloys, with which the present paper is concerned. - The work to be discussed represents essentially an extrusion study of the Mg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metal¬lography, and toughness of these alloys. Compositional variations are limited to the ranges o to 7 per cent Zn and o to I per cent Zr. EXPERIMENTAL PROCEDURE Alloying and Casting Alloying ingredients were cell mag¬nesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl2 and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manu¬facturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zir¬conium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux¬inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1946

By R. E. Reed, C. J. McHargue

Single crystals of aluminurn were reduced 90 pct in diameter by extrusion at 296" and 77°K. The resultant double fiber texture had a strong (111) component with a weak (001) component. The relative anzounts of these components varied with starting orientation. Decreasing the Lemperatuve of defovtnation increased the amount of (001) texture component in crystals with inilia1 orientations near (111). The starting orientation and temperature of deformation strongly affected the morphology of the (001) component. The effects of orientation and Lemperatuve upon the distribution of the (001 ) texture component in extruded aluminum single crystals were rationalized on the basis of deformation band formation and interaction. MANY papers since the early 1920s have discussed the occurrence of the double fiber texture (111) + (001) in wires and rods of deformed fcc metals. Aside from the reporting of experimental results for the various metals under a variety of fabrication conditions, emphasis has been placed on two related problems. One problem deals with the prediction of ideal end orientations based on the glide systems and flow directions. The other problem seeks the reason why different amounts of each component may be produced by the same fabrication schedule for metals apparently having the same deformation systems. Some of the difficulties in developing a satisfactory explanation have their origin in the experiments themselves. One mistake has often been the assumption of an initially randomly oriented specimen or complete ignorance of effects of starting orientation. Recent studies by Grewen and Wassermann,1 Cullity and co-workers,2' and McHargue4 have shown that the initial orientation may be the most important factor in determining the final orientation. Hence only limited comparisons of data from different studies can be made unless all conditions of the initial material are specified. Another question has been the nature of the (001) component. Hibbards suggested that any (001) present was the result of re crystallization during fabrication. Although Fleischer6 found no (001) texture in aluminum swaged at room temperature, and Dayal 7 found that component to disappear at very high reductions, a double fiber texture has usually been reported for aluminum. Vandermeer and McHargue showed that, while some (001) in aluminum may be the result of recrystallization, much of this component has its origin in the deformation process. Ahlborn and Wassermanng found the (001) component in silver deformed at low temperature not to be the product of recrystallization.

Jan 1, 1968

By George A. Connell

BORAX, a sodium borate and the principal sodium salt of boric acid, has been surrounded with romance and with a certain amount of mystery. Its early history is not entirely known but it has been contended that Marco Polo in his travels in the Orient introduced this material to the West during the Middle Ages. Without doubt its first source was from Central or Eastern Asia and perhaps from Tibet. The well-known fluxing properties of borax probably introduced its earliest use that of a soldering flux in the manufacture of jewelry. This use, as well as the remote location of most borate deposits, added greatly to the romance associated with the thought of borax. COMPOSITION The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture of disodium tetraborate (Na2B4O7.10H2O), and, further, can be considered as the acid salt of monosodium metaborate. However, the term "acid salt" might imply that borax gives an acid reaction in solution, which is not true, since solutions of borax are decidedly alkaline, giving a pH of 9.2. Boric acid, also known as boracic acid, has the chemical formula H3BO3; it occurs in nature as the mineral sassolite. Sassolite has been

Jan 1, 1949

By R. B. G. Yeo

The effects of alloy additions on the M, and A, temperatures of an Fe-22.5 pct Ni alloy have been determined. Increasing amounts of titanium, colum-bium, vanadium, and silicon raise and then lower M,while raising A, cmtinuously. Cobalt raises both M, and A,. Aluminum has little effect on Ms but raises A,. Chromium md nickel lower M, and A,. It is proposed that elements raise M, in accordance with their effect on the Ae3 temperature of iron until the lattice becomes stiffened against the shear transformation so that M, is then lowered. An anomaly, first pointed out by Zener,1 arises in steels when the addition of elements, such as molybdenum and tungsten, which raise the Ae3 temperature, also lower the M, temperature.2'3 During the development of a series of martensitic precipitation-hardening (maraging) steels, the effect of several elements on the transformation of austenite to martensite was studied. The results show that under suitable conditions several elements which raise Ae3 also raise the M, and A, temperatures. PREPARATION OF MATERIALS STUDIED A series of alloys was made in which cobalt, titanium, columbium, vanadium, silicon, aluminum, molybdenum, chromium, and nickel were added to an iron base containing 22.5 pct Ni. The compositions of the alloys prepared are given in Table I. The residual manganese contents of the heats were in the range of 0.030 to 0.35 pct, silicon 0.05 to 0.1 pct, carbon 0.0008 to 0.009 pct, and nitrogen from 0 to 0.004 uct. The allois were made as 50-lb induction heats starting with electro-iron and electro-nickel, melted in air to oxidize impurities. Additions of silico-manganese and ferro-silicon were made after which the power was turned off to allow the products of deoxidation to rise and be skimmed from the surface of the melt. The furnace chamber was pumped down to a pressure of 5 p and the charge was heated to 2900°F for the addition of other alloying elements. The heats were poured into five 10-lb ingots, making successive alloy additions to each. The ingots were soaked for 2 hr at 2300°F and hot-worked to 3/4-in.-diam bars. This stock was heated to 1500°F for 1

Jan 1, 1963

By C. M. Nickerson

In times of overproduction such as the operators have been struggling against for the past several years it is the practice of the oil industry to shut in certain wells in order to reduce the flood of oil. The purpose of this paper is to present certain variations in production of oil wells when the offset wells are shut in. The scope of the study has been confined to California fields, and more especially to those of the San Joaquin Valley. The accepted definition of a shut-in well is a well where production has been suspended by closing in the casinghead arid tubing or by cessation of pumping. The immediate effect of such a procedure, of course, is to reduce the oil production from the lease, which is the result desired. However, it appears that certain types of wells vary widely in production of oil, gas and gasoline after adjacent wells have been shut in, which variation has a very material effect on the ultimate recovery of oil from the property. The increase or decrease in the oil production itself may not be of sufficient volume to occasion comment, but wide fluctuations in the gas and gasoline recovery under the changed conditions arc of the utmost importance in the future recovery of oil. The scope of this paper includes: (I) the effect on producing oil wells of shutting in offset wells, the wells being studied in three groups arranged according to their relative stages of depletion; (2) probable source of excess gas and the effect on the ultimate recovery of oil; (3) suggested procedure when wells are shut in; (4) methods that could be employed to prevent undue migration of gas from the shut-in area; and (5) the need for future studies of the situation. Three Classes of Producing Oil Wells For the purposes of this paper producing wells in California have been arranged in three groups according to the age of the well, or to the relative stage of depletion of the producing zones. The first group consists of those wells with a high fluid level, or in other words those wells whose fluid levels are a considerable distance above the top of the perforations. This type of well is in the flush period of its life and ordinarily produces

Jan 1, 1929

By Luiz C. Correa da Silva, Robert F. Mehl

An experimental study of the movement of markers in the systems Cu/a-brass, Cu/Sna-solid solution, Cu/Ala-solid solution, Cu/Ni, Cu/Au, Ag/Au, employing many types of markers and a variety of temperatures. Marker movement is confirmed and undoubtedly associated with the manner in which atoms move during diffusion. EVERAL years ago Smigelskas and Kirkendall' •S reported measurements on the interdiffusion of copper and a-brass and on the movement of inert markers placed at the original join. These markers were observed to move toward the a-brass side of the join, and from this it was inferred that zinc diffuses in a-brass more rapidly than copper. Similar results were reported a little earlier for the diffusion of solvents into high polymer solids.' This has attracted much attention, particularly from those interested in the mechanism and the theory of diffusion: Seitz3 has employed it in supporting the vacancy theory of diffusion; from the data Darken4 has calculated separate diffusion coefficients for copper and zinc, developing a "phenomenological" theory of diffusion; and Bardeen5 has employed it in constructing a general theory, including therein the work of Seitz and Darken, as has Le Claire. These matters have recently been reconsidered in a sympo~ium.7 Some reason has existed for questioning the work of Smigelskas and Kirkendall.' Their technique consisted in electroplating copper on a-brass, upon the surface of which Mo-wires had been secured, and then diffusing, measuring the extent of diffusion along the normal to the join, and measuring the marker displacement in the same direction by a comparator determination of the distance between Mo-wires on opposite sides of the electroplated brass sample. It has been suspected that the copper plate might have been porous, and that the original interface might have been an imperfect join, both contributing to the transfer of the volatile zinc by vapor transfer;' it has also been questioned whether the marker movement might not in a measure be a property of the marker itself; etc. These legitimate questions require experimental answers; the present paper offers such answers. Moreover, Smigelskas and Kirkendall studied the effect only in the Cu-Zn system and at one temperature; the attention which the work of Smigelskas and Kirkendall has commanded recommends similar

Jan 1, 1952

By T. R. Graham, R. S. Dean. J. R. Long

Following the development of electrolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau's program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to compositions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study' established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, I0 pct manganese, 25 pct zinc alloys;1 a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-worki"g and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

By R. S. Dean. J. R. Long, T. R. Graham

Following the development of electrolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau's program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to compositions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study' established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, I0 pct manganese, 25 pct zinc alloys;1 a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-worki"g and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

By J. F. Myers, F. M. Lewis

THE crushing of ore, as defined by Taggart,1 is "usually a stage process, utilizing . . . machines especially suitable for the reduction of particular sizes... . down to a final stage, employed for the reduction of the finest sizes. . .. In contradistinction, comminution to 20-mesh or finer is called grinding. There is a twilight zone in which the product is 6, 10, or 14mesh limiting size which is either crushing or grinding. . .. " Since the data in this paper pertain to a rod-mill operation, comminuting a particular ore size of ¾ in. to a final stage, coarser than 20-mesh, the rod mill is designated as a "fine crusher machine" in this paper. The published literature discloses a wealth of data regarding a rod mill as a fine-grinding machine but relatively little as a fine-crushing operation. Typical of the latter operation is: (I) a description by F. J. Tuck2 in which a fine-crushing rod mill replaced crushing rolls and (2) a description by the present authors3 in which a fine-crushing rod mill was installed instead of a conventional fine-crushing machine. The experience of the authors is that a definite distinction must be made between the rod mill functioning as a fine crusher and as a fine-grinding machine. As a fine-crushing machine it prepares * relatively large amounts of ore for a subsequent fine-grinding operation; as a grinding machine, it grinds relatively small amounts of ore to some predetermined finished product. PULP MOVEMENT AND ACTION IN MILL In considering the work performed by a fine-crushing rod mill, it seems important to understand just what takes place within the mill. We were inspired to study this matter by a paper by E. W. Davis,4 which indicated that definite water classification of ore particles took place in a ball mill. However, in thinking of the rod-mill action from this point of view, we were confronted with the fact that our rod-mill discharge product showed no evidence of action by water classification. The Tennessee Copper Co. ore is relatively high in sulphides, and the gangue rock and the sulphides are of about the same hardness. In the presence of any action by classification, the coarser sizes are definitely very lean in sulphide minerals. [ ]

Jan 1, 1946

By W. T. Hicks

Visual observation of the oxidation of columbium shows that the protective behavior noted previously in gravimetric work in the early stages of the reaction below 600°C and throughout the reaction at 640°C is associated with an adherent oxide. The fact that the oxide is seen to move outward from the metal at temperatures from 550° to 935°C implies that the reaction takes place at the oxide-metal interface throughout this temperature range. THE work described in this paper further clarifies the complex oxidation kinetics of Cb revealed, for example, by the continuous gravimetric studies of T. L. Kolski.1 Time-lapse motion picture studies reveal details of the reaction not provided by a study of the combustion products. EXPERIMENTAL PROCEDURE Cb specimens were prepared from material with the following typical analysis: 0, 0.03 pct; N, 0.002 pct; C, 0.006 pct; Ta, 0.04 pct; Fe, 0.01 pct; Ni <0.003 pct; and Cr <0.003 pct. Arc-cast ingots were swaged and cold rolled into slabs. These slabs were machined into blocks 7/16 by 7/16 by 7/16 in; 1/16-in. holes were drilled through the large face of the blocks for suspension. The samples were then de-greased and annealed 1 hr at 1200°C in vacuum. The sample was suspended by a platinum and Pt 10 pct Rh thermocouple inside a 1-in. quartz tube in a Kanthal wound furnace (2 in. OD by 4 in. long) equipped with windows 1/2 in. sq. A Cine-Kodak Special II 16 mm motion picture camera was trained on the sample through a Spencer microscope adjusted so that a magnification of X1.5 resulted on the film. Super Anscochrome film was used to record the events in color. Argon was flushed through the furnace while the sample came to temperature. The argon was then replaced by a stream of dry oxygen at 1 atm. Pictures were taken at the rate of eight per second for about 20 sec during the change of atmosphere. Then by use of a Stevens time-lapse device pictures were taken at the rate of four per minute starting within 1 min of the initial oxygen flow. In this manner continuous visual records of the oxidation of pure Cb

Jan 1, 1962

By A. Bar-Or, G. Hirsch, P. Wynblatt

The rates of nucleation and growth at various temperatures in U-0.45, 1.1, and 1.35 at. pet Cr alloys were determined, providing a qliantitative proo-f that the transformation under study is controlled by nucleation and diffusional growth. The linear relationship, log NV US 1/T2, suggests that the nucleation of the alloys is probably controlled by the classical law of nuclei formation. The established linear relationship, log G us 1/T, in the three alloys suggests that growth in each alloy is controlled by bidimensional nuclei formation. It was established that both the rate of growth and the rale of nucleation are retarded by chromium. Using classical formulae, sApN and sApG (the ß/a apparent interphase energies) were calculated from the nucleation and growth results, respectively. It was found that their values are of the same order of magnitude. However, why sApN is unaffected by the addition of chromium, while sApG increases with it, needs further clarification. In the last few years, an appreciable amount of research has been conducted into the mechanism of the ß —a transformation in uranium and uranium alloys. Recently, Burke1 reviewed the published work concerned with this transformation. He concluded that in dilute uranium alloys it is firmly established that, at high temperatures in the a range, ß decomposes by a diffusional process. However, he based his conclusion either on experiments dealing with the over-all transformation,2 or on qualitative results.3 It was felt that a better insight into the mechanism of transformation could be gained from the quantitative measurements of growth and nucleation rates, which we aimed to carry out in the present work. In a previous work,4 we have shown that a rim of a grains is formed during isothermal transformation at the high a range. The thickening of this rim with time was used for measuring the rate of growth in U-0.45 at. pet Cr.5 This method was also used in the present work for two more alloys. For meas- uring the rate of nucleation, a method of quenching and macroetching was developed to allow differentiation between a grains formed during isothermal transformation at the upper a range and those formed after quenching, Fig. 1. EXPERIMENTAL WORK AND RESULTS The Rate of Nucleation. The measurement of the rate of nucleation was effected by counting the num-

Jan 1, 1965

By W. G. Woolf, E. R. Crutcher

The electrolytic zinc plant of the Sullivan Mining Co. is in Government Gulch, at Silver King, Shoshone County, Idaho, in the Coeur d&apos;Alene mining district, about one mile from the Bunker Hill smelter and about three miles from Kellogg. The Sullivan Mining Co., which owns both the zinc plant and the Star mine, is itself owned jointly by the Bunker Hill & Sullivan Mining & Concentrating Co, and the Hecla Mining Company. The Tainton high-density, high-acid process is used at this plant, therefore some parts of its flowsheet differ markedly from those of electrolytic plants using the low-density process. While it is a custom plant and has treated a variety of zinc concentrates originating from various sources in a number of states, it has obtained its main supply of zinc concentrates chiefly from the zinc-bearing ores of the Coeur d&apos;A1ene mining district, of which the principal important sources have been the Bunker Hill and Star mines. Thus the main feed has been zinc concentrates obtained from complex lead-zinc-silver ores. For the year of 1935 the concentrates had the following composition: water, 9.5 per cent; Zn, 50.6; Pb, 3.3; Fe, 9.4; S, 31.0; Cu, 0.2; insoluble, 2.9. Flowsheet The concentrates are delivered to the plant in railroad cars, which discharge into storage bins directly under the track. Bottom-dump cars are dropped directly into the bins while a slip scraper, pulled by an air tugger hoist, is used to empty box cars. There are five storage bins for concentrates, each of approximately 300 tons capacity. At the bottom of each bin there are individual belt feeders that discharge onto a common conveyor belt, which in turn discharges to another belt that carries the concentrate onto a weightometer belt for weighing. Immediately after the weighing, the crushed oversize return from the roasters is added to the load on the belt and then the ground-up sweepings, lumps and roaster cleanings. An electromagnet at the end of this conveyor removes tramp iron from the feed. The belt discharges to a set of 30 by 12-in. rolls, which break up lumps or frozen chunks of concentrate, etc. Beneath the rolls there is a screw conveyor, which conveys the roll discharge to a

Jan 1, 1937

By J. Versluys

When a well strikes an oil-bearing layer, the oil has a pressure which is generally sufficient to enable it to rise to near the surface (sometimes above the surface). As soon as a well begins to produce, however, the liquid moves through the pores of the reservoir bed and the pressure in the well becomes much lower than the pressure originally prevailing there. At some distance from the well, however, the pressure in the reservoir bed remains unaltered; thus the pressure of the oil has not only to lift the oil, but also to overcome the friction resistance in the pores. The fact that so many oil wells are gushers is a consequence of the energy accumulated in the gas. In gushing the well acts as a gas-lift. A mixture of liquid and gas (the latter partly dissolved in the former) rises vertically from the oil-bearing layer through a cylindrical casing to the surface. In time conditions alter and the well ceases to gush regularly, then the gushing can be further promoted by inserting a narrower tube in the well and connecting the top of the oil string to the tubing. If the action in time becomes irregular, the gushing can be kept up for a further period by forcing gas between the two tubes. In the oil fields the term "gas-lift" is used actually only where extraneous gas is applied, as in the last of the stages mentioned. The action, however, is just the same whether the gas exclusively originates from the formation, or is partly applied artificially. Thus by gas-lift we simply mean a vertical tube in which the energy of gas under pressure, and of dissolved gas, is utilized for raising a liquid. In gushing oil wells the pressure is frequently very high and the absorption coefficient 0.4 (expressed in vol. ratio) of the coexisting gas is not particularly high, so that in reality it should be assumed that a considerable portion of the gas, at any rate at the bottom of the gas-lift, is dissolved in the oil. For water-producing wells this is not usually of such importance. Where the volume of the flowing gas is much greater than that of the flowing liquid, the latter can be suspended in the former in the form of

Jan 1, 1930

By Robert T. Howard, Morris Cohen

IT has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkin1 has shown that the compositions of two coexisting phases in a a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanalysis.3 Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantitative way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of, this research could not be treated satisfactorily by other quantitative tools, such as specific volume,4 magnetic,5 dilatometric,6 electrical resistance7 or x-ray measurements.8 It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. LITERATURE SURVEY Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1947

Cortez Gold Mines operated a conventional 2,100 mtpd (2, 300 stpd) cyanidation plant until the 5 million ton ore body was worked out in 1973. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME 1975.) Sub-grade material was dump leached at the mine -mill location in 1971, and the resulting pregnant solutions were added to the feed in the plant&apos;s Merrill-Crowe precipitation unit for gold recovery. In early 1973, however, Cortez put into operation their Gold Acres mine which was located about 13 krn (8 miles) to the west of the &apos;Cortez mine. Economics at that time dictated the heap leaching of the lower grade portion of the ore body with the higher grade being trucked to the Cortez plant for milling. Leach ore was moved directly from the open pits to prepared leach pads located on a gently sloping terrain of 570 grade. Preliminary pad preparation at the leach site included removal of vegetation which was composed of sagebrush and grading of the base. Pads were comprised of mostly minus 74 micron (200 mesh) materials and were made of clay-silt or slime tailings spread on the pad area in thin 50 to 75 mm (2 to 3 in. ) layers, compacted with a vibrating roller compactor to a depth of about 380 mm (15 in.). This was followed with a 100 mrn (4 in.) layer of coarse rock to prevent erosion on the pad and to allow solutions to move laterally under the heaps. Leach solutions normally traveled the length of the heaps and were collected in plastic-lined ditches from which they flowed by gravity to the pregnant solution storage pond. Both pregnant and barren ponds were constructed in the same manner as the leach pads - being lined with compacted tailings or clay silts. The Gold Acres facility required pregnant solution storage of 6 million liters (1.6 million gal) and barren storage of 3.8 million liters (1.0 million gal) designed to handle two to three days of heap drainage or to retain run-off from a major rainfall. Various heap heights were tried including 3, 6, and 9 meters (10, 20, and 30 ft), with a 6 m (20 ft) height selected. Ore was dumped by trucks in a single 6 m (20 ft) lift using a D8 Caterpillar dozer for

Jan 1, 1981

By Richard E. Goodman

Rock slope stability assumes different roles in decision making as a mining venture develops and, accordingly, geological investigations vary in thought and in deed according to the project stage. During exploration, stability questions bear on the decision whether or not to mine, because their resolution affects the cost of mining. During the mine lay-out stage, stability is a key factor in deciding how to mine. Finally, during mine operation, stability affects safety and operating costs, and therefore, pit productivity. Among the many considerations influencing stability, rock mass classification and geological environmental factors count heavily. The rock mass behavioral class depends upon the rock character and its degree of fracturation. The loads on the rock are derived from the environmental factors of initial state of stress and the water regime. Of course, stability is also tied to a host of non-geological factors such as the pit geometry, mining style, relative wealth, philosophy of mine operation, and accident history. METHODS OF STABILITY EVALUATION AND CORRESPONDING INVESTIGATORY TOOLS The purposes of the geological investigation are to identify and evaluate the geological factors influencing stability so that the vital questions can be analyzed. The tools selected for stability analysis reflect the stage of development of the mining scheme and therefore the geological investigations, which must furnish data for the analyses and must vary with the project stage. For exploration and mine planning, the methods of resolving stability questions must meet the need to evaluate numerous parameters in limited time; examples of such methods are stereographic projections (1, 2, 3) charted solutions(4) and simple physical models (5, 6). An investigation program that employs geological mapping tools and aids to mapping, such as geophysics, with relatively few rock tests, is in balance with these analytical methods. First data about the water regime are obtained from observed piezometric levels, and the initial state of stress is queried simply through geological inference and experience. In the layout stage more elaborate physical scale models (7) and perhaps finite element models (8, 9, 10, 11, 12), will be relevant to the design process and therefore much more detailed geological investigation is required. The scale of observation of both rock material and joints will be significantly enlarged and mechanical tests of rock and joint strength

Jan 1, 1972

By Martin Epner, Eric Gregory

DURING the past decade, considerable work has been carried out on various cermet systems in an effort to produce materials suitable for high-temperature applications in gas turbines. Most of the materials have not, as yet, met the requirements of the engine manufacturers, primarily because of their lack of room-temperature ductility and thermal shock resistance. In the field of tool materials, however, although ductility is still of prime importance, much has been accomplished by improving design parameters and the quality of carbide materials with a view to using cermet compositions successfully. The systems described in this paper were designed primarily for application in this field, although their development was a natural outcome of work on similar compositions designed for high-temperature service. In steel-bonded titanium carbide, the steel binder imparts heat treatability to the system while the carbide provides abrasion and wear resistance. Combining the carbide and the steel matrix in carefully controlled proportions results in a composite material which, when the steel is hardened, has man of the properties of cemented tungsten carbide. In the annealed condition, this material can be readily machined by the conventional chip-removal techniques. Titanium carbide has certain distinct advantages over many of the other carbides when combined with a steel matrix. It is among the hardest of the carbides and is one of the most stable. Liquid iron wets titanium carbide, and this wetting assists in the formation of a dense cermet. Once the composite structure has been formed, the titanium carbide acts as a relatively inert phase during the heat treatment of the matrix. PREPARATION OF ALLOYS The steel-bonded titanium-carbide materials described in this paper were prepared by the liquid-phase sintering technique. The titanium carbide used had an average particle size of 6 to 7 p, a total carbon content of 19.4 pct and 0.35 pct free carbon. This was blended with the elemental metal powders by ball milling them together in a hexane medium. After drying, paraffin wax was added to the blend to provide green strength in the pressed briquettes, and compacting was performed at 15 tsi. Liquid-phase sintering was carried out in vacuum at temperatures which depended on the chemical composition of the system involved, but which were usually around 2640° F. The resultant materials had a density approaching 100 pct of theoretical. The

Jan 1, 1961

By Louis A. Riley

I DESIRE to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomer¬ates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideration in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

Jan 1, 1877