Search Documents

By G. Krauss, W. Pitsch

The fine structure of the bcc martensite formed in an Fe-33 wt pct ATi single crystal of arrstenite is sho~on by transmission electron microscoPy to consist of combinations of transformation twins, stacking faults, deformation twins, and regular arrays of parallel screw dislocations. These structures constitute evidence for the multiple lattice-invariant deformations which operating during the formation of martensite could produce the real habit-plane scatter measured by a two-surface analysis of the plates formed in the single crystal of this investigation and reported in the literature for other Fe-Ni rnartensites. CRYSTALLOGRAPHIC theories1,2 of martensitic transformation show that the habit plane of martensite in a parent lattice is dependent in part upon an inhomogeneous distortion or lattice-invariant deformation which takes place on a fine scale within a martensite plate during its formation. Several recent theoretical papers3,4 have addressed themselves to an analysis of a wide variety of conceivable lat-tice-invarient deformations and the habit planes which they produce, while experimental investigation have been concerned with either the measurement of habit planes or the description and identification of the martensitic fine structure which reflects the nature of the lattice-invariant deformation operating during transformation. In Fe-Ni alloys with subzero Ms temperatures, the group of alloys with which this paper concerns itself, habit planes have often been found to scatter an amount greater than might be expected from possible experimental errors,5-7 and fine twinning has been identified as a major constituent of the fine structure of martensite.8-11 It has been suggested3,4 that more than one type of invariant shear occurs during martensitic transformation. This possibility has been experimentally supported12,13 by the observation of both dislocation configurations and twinning in a single martensite plate. The purpose of this paper is to report additional evidence for multiple lattice-invariant deformations in martensite and so to account for the real scatter in the habit planes of the martensite plates formed in Fe-Ni alloys. EXPERIMENTAL PROCEDURE The Fe-Ni single crystal was produced by pulling a high-purity iron and nickel charge through a single-crystal vacuum furnace in an alumina crucible. The crystal was double-melted to promote homogeneity and to increase its size by further additions on the second pass. In its final form the crystal was 4 cm in diam and 5 cm long. The nickel and carbon contents were analyzed at 32.9 and 0.006 wt pct, respectively. The austenite of this alloy first transformed to martensite by bursts at about -120°C, and, to preserve as much of the austenite as possible, all transformation was performed just below -120°C. Some observations were made on transformed samples which had been heated for 2 min at 340°C. It is assumed that the features of the martensite of these samples, Figs. 1 and 4, are the same as those of the as-quenched martensite. Orientation of the crystal by X-ray diffraction established 10.735 0.609 0.3161? as the axis of the crystal, an orientation that was checked within 2 deg by neutron diffraction. Further checks by electron diffraction of samples cut normal to the axis confirmed this orientation within the larger limits of error inherent in electron diffraction of thin foils. The X-ray orientation was the one used for the two-surface analysis of the martensite habit planes. A two-surface analysis was performed on the quadrant of the single crystal which had been oriented by both X-ray and neutron-diffraction techniques. Photomicrographs at X50 were made on two surfaces along an edge 2 cm long. Fiducial marks and the fact that many of the plates were almost completely surrounded by retained austenite made good matching of individual plates on two surfaces possible. The habit-plane trace on a surface was taken as the best line parallel to the long axis of a plate. A measure of the accuracy afforded by this criterion was provided by a family of very large plates which appeared at intervals along the entire 2 cm length of the edge. The plates all had habit-plane traces within 2 deg of one another. Many of the plates did not show midribs and, therefore, the use of midribs7 to represent habit-plane traces was not feasible in this investigation. The over-all experimental accuracy is estimated to be better than ±2 deg. Samples for transmission examination in a Siemens Elmiskop I at 100 kv were prepared by cutting 2-mm-thick discs from the single crystal, removing about 0.5 mm by chemical polishing,14 trans-

Jan 1, 1965

By Magnus Troilius

INTRODUCTION BY C. P. SANDBERG. SINCE the discussion On steel rails in America has forcibly drawn attention to the value of chemical analysis, if not as a necessary stipulation, at least as a guide to control the usual mechanical tests, some doubt has been thrown upon the accuracy of the analytical results Obtained by different chemists. To any One having the least acquaintance with chemistry., it is quite clear that if exactly similar results are to be obtained from the same borings of steel, exactly the same methods must be used by the different analysts. Hence the necessity (if complications are to be avoided) of establishing what I may call standard or normal methods, to be used both by the inspectors and by the chemists at the works. Remembering that the application' of chemistry to steel-rail inspection is yet in its infancy, it is of great importance to possess a perfect acquaintance with the best methods in use. Being myself a grateful pupil of Professor Eggertz, of the School of Mines in Sweden, it Occurred to me, two. years ago, that I could not do better than start a laboratory of my. own, and engage One of his pupils, Mr. Troilius, for the purpose of analyzing the steel borings from mechanically-tested rails, so that I might thus Obtain without delay thoroughly accurate determinations. Moreover, in Order to carry on the, operations in perfect accordance with the methods used at the steel works in England and Germany, where I had to control the manufacture, I deemed it desirable to allow Mr. Troilius to go through a course of training at these works; and I gladly seize this opportunity of expressing my grateful acknowledgments to several works in England and in Germany for affording every facility for such an exchange of information as was found necessary in arriving at the best analytical methods to be used.

Jan 1, 1882

By Walter H. Bucher

This symposium is designed to lay the basis for a general discussion of the place of geophysics in the training of geologists. As there is danger that in the ensuing debate individual interests may be given emphasis out of proportion to their place, we shall do well to view the whole field of geological inquiry in order to see the problem in true perspective. The Nature of Geological Inquiry "Basic" and "Complex" Sciences It is convenient to divide all science into two major divisions, the basic and the complex sciences. The basic sciences separate out from reality such entities as "substances" and "movements," describe their behavior in terms of arbitrary units of measurement and derive from them by progressive abstractions concepts and patterns of behavior that exist between them, so-called general "laws" and "properties" of nature. The complex sciences, on the other hand, deal, with little or no abstraction, with those objects of reality that are accessible to man in the atmosphere, the hydrosphere, the lithosphere and the biosphere. Their work comprises two types of inquiry. One is concerned with abstractions to the extent of dealing with types rather than individuals—that is, with such things as plants, animals, protoplasm; clouds, streams, gla- ciers; volcanoes and mountain ranges. It comprises the search for general properties and patterns of behavior or "laws" that characterize the objects and their reactions to each other. These properties and laws apply always, everywhere. They are independent of the stream of time. We may call the results of this sort of inquiry timeless knowledge. The other type of inquiry is concerned with the objects themselves—that is, with this animal and that plant; this river system and that mountain chain; this glacier and that valley. Like all concrete objects in nature, they are subject to change with the passage of time, especially when it is measured in years, centuries, eons. The characteristics by which we recognize them —indeed, their very existence—are dependent on their position at this point in the stream of time. This we may call time-bound kntowledge. The so-called descriptive sciences are all bound to the past of which the objects of their study are the product and through which alone their present properties call be understood. They are historical sciences. This obvious fact is easily overlooked, which leads to serious misunderstanding, as we shall see later. Dynamic Geology With this broad picture in mind, let us now examine the nature of geological inquiry, defining, for the purposes of this discussion, geology as the science of rocks. Air is not a rock; water is. Meteorology and climatology are, correspondingly, gen-

Jan 1, 1946

By Walter H. Bucher

This symposium is designed to lay the basis for a general discussion of the place of geophysics in the training of geologists. As there is danger that in the ensuing debate individual interests may be given emphasis out of proportion to their place, we shall do well to view the whole field of geological inquiry in order to see the problem in true perspective. The Nature of Geological Inquiry "Basic" and "Complex" Sciences It is convenient to divide all science into two major divisions, the basic and the complex sciences. The basic sciences separate out from reality such entities as "substances" and "movements," describe their behavior in terms of arbitrary units of measurement and derive from them by progressive abstractions concepts and patterns of behavior that exist between them, so-called general "laws" and "properties" of nature. The complex sciences, on the other hand, deal, with little or no abstraction, with those objects of reality that are accessible to man in the atmosphere, the hydrosphere, the lithosphere and the biosphere. Their work comprises two types of inquiry. One is concerned with abstractions to the extent of dealing with types rather than individuals—that is, with such things as plants, animals, protoplasm; clouds, streams, gla- ciers; volcanoes and mountain ranges. It comprises the search for general properties and patterns of behavior or "laws" that characterize the objects and their reactions to each other. These properties and laws apply always, everywhere. They are independent of the stream of time. We may call the results of this sort of inquiry timeless knowledge. The other type of inquiry is concerned with the objects themselves—that is, with this animal and that plant; this river system and that mountain chain; this glacier and that valley. Like all concrete objects in nature, they are subject to change with the passage of time, especially when it is measured in years, centuries, eons. The characteristics by which we recognize them —indeed, their very existence—are dependent on their position at this point in the stream of time. This we may call time-bound kntowledge. The so-called descriptive sciences are all bound to the past of which the objects of their study are the product and through which alone their present properties call be understood. They are historical sciences. This obvious fact is easily overlooked, which leads to serious misunderstanding, as we shall see later. Dynamic Geology With this broad picture in mind, let us now examine the nature of geological inquiry, defining, for the purposes of this discussion, geology as the science of rocks. Air is not a rock; water is. Meteorology and climatology are, correspondingly, gen-

Jan 1, 1946

US 4,134,618-Method for restoring an underground reservoir subsequent to the solution mining of an ore body of uranium, copper, nickel, vanadium, molybdenum, silver, rhenium, or selenium. Clean water a cycled through the mined area, via the injection and production wells used during mining, at a flow rate sufficient to entrain residual dissolved solids. The solids are separated at the surface and disposed of, e g., in a deep disposal well, while clarified water is recycled C A. Kossack, assigned to Atlantic Richfield Co. Jan 16, 1979 4 pp. (299-5) Filed. 12-29-77 (865,646) US 4,155,982-In situ leaching of a subterranean uranium ore deposit The ore is leached with a dilute aqueous solution of ammonium bicarbonate containing a small amount of hydrogen peroxide in order first to convert tetravalent uranium in the ore to the hexavalent state and second to dissolve the hexavalent uranium preferentially to the other metals or elements commonly occurring In such ore The uranium- enriched leach liquor IS brought to the surface, and the uranium recovered by means of adsorption on a particulate ion exchange resin, elution with an acid, and treatment with ammonia to precipitate relatively pure ammonium diuranate. G G. Hunkin, T P. Fife, and J R Stano, assigned to Wyoming Mineral Corp. May 22, 1979. 13 pp (423-7). Filed: 10- 9-74 (51 3,445). Same: Canadian 1,027,849, dated Mar. 14, 1978. US 4,157,847-In the mining of sulfur by the Frasch process hot water accumulating above subterranean sulfur from previous mining operations is recycled downward to contact and heat additional solid subterranean sulfur. Advantageously, pressurized and superheated drive water from above ground is commingled with the underground water to raise its temperature before it is recycled downward R. L Williams, R L Latiolais, J. L Gabriel, and R. L Bouis, assigned to Freeport Minerals Co June 12, 1979. 13 pp (299- 6) Filed 7-28-77 (81 9,879). US 4,158,76%1n this method for determining the uranium content of a solution obtained in the solution mining of an underground uranium ore deposit, the intensity of gamma radiation from the Th-234 daughter of U-238 emitted by the solution is determined as it impinges on a scintillator after being passed successively through filter foils of a ytterbium- tin alloy, a lutecium-tin alloy, and a hafnium-zirconium alloy This scintillation is evaluated as a measure of the uranium content To assure that the uranium-thorium conversion has reached a stable state, the measurement should be made about three months after the uranium solution has been produced R C Smith, assigned to Westinghouse Electric Corp. June 19, 1979 11 pp. (250-255). Filed. 10-20-77 (843,770).

Jan 1, 1980

By A. E. Bellis

ROBERT J. ANDERSON, Cleveland, Ohio (communication to the Secretary *).-The paper by Messrs. Bellis and Hardy was interesting to me and has led me to make a few remarks concerning some of the points brought out. The question of employing correct hardening temperatures is one that is sadly neglected, particularly in many large plants that forge and treat their machine tools for private use. As is most aptly remarked in this paper, "The custom of using one, high-speed temperature for all tools is very poor practice;" still, such practice is more common than otherwise. An instance came to my attention some time ago, in connection with some work with the standardization of high-speed steels for machine tools, where there were no less than six different brands of alloy steels being used for machine tools such as lathe, shaper, planer, boring mill and cutters of like nature. All of these different steels received identical heat and forging treatment-or at least that was the aim of the tool hardener. That the results were highly unsatisfactory goes without saying. That the hardening department of many plants is conducted on a rule-of-thumb fashion is the reason for a great deal of the trouble and disappointment which seems to be the lot of many tool-steel users. Exceedingly crude execution is the rule rather than the exception, and it is no small wonder that the results are as good as they sometimes happen to be. It would seem that at the present price of alloy steels the subject should receive a closer scrutiny by purchasers than it does. One not familiar with the workings of souse plants that disdain to lend an ear to scientific heat treatment would scarcely give credence to some of the methods employed, not only in the treatment of the steel but also in its selection and purchase. Heating for hardening should be conducted under close pyrometric control only after the correct hardening temperature has been determined.

Jan 3, 1917

By Dermot M. Ross-Brown

Introduction Slope angles are one of the major factors affecting the shape of the final pit and the location of the walls Due to differences in geology, the optimum slope angles vary from pit to pit and within different parts of the same pit. Indeed, it is not unusual to have different slope angles for the top and bottom portions of the same cross section. The optimization of these slope angles is a major study in itself and this chapter is intended as a general introduction to the subject. It is not intended to be a comprehensive text for the absolute beginner The objective is to put the various aspects of slope stability analysis into relative perspective by describing the vari¬ous analytical techniques available and indicating when each may be most appropriately used References are made to the many excellent texts and papers on slope stability for the reader who does not have a formal training in soil or rock mechanics. In writing this chapter, an assumption has been made that a tentative mining plan has been drawn up, includ¬ing a preliminary estimate of the slope angles. It has also been assumed that all the necessary field and laboratory data has been collected and reduced to a form suitable for input into the stability analyses.

Jan 1, 1979

By Robert M. Keeney

Important recent developments in the melting and annealing of non-ferrous metals include: 1. Melting of nickel silver in the vertical ring induction furnace. 2. Electric melting of stereotype metal. 3. The rotary-drum gas-fired brass melting furnace. 4. The low-frequency coreless induction furnace. 5. Finishing annealing of brass sheets with city gas1 replacing wood in the large brass-rolling mill. 6. Electric annealing of brass and copper tubing and sheets. 7. Replacement of oil by gas and electricity in the annealing of nickel-silver shells and stampings. Melting Nickel Silver in Vertical Ring Induction Furnace Although over 90 per cent. of the output of the brass rolling mills in the United States is now melted in electric furnaces,2 until recently a considerable part of the output of nickel silver has been the product of the pit fire. The application of the electric furnace to the melting of nickel silver has been slow for several reasons: (I) Until recently no lining has been available that gave a satisfactory life in the vertical ring induction furnace when melting nickel silver; (2) the rocking arc furnace so widely used in the foundry does not appear to have been favored by the rolling mill for melting nickel silver, possibly because the gases present may affect the quality of the alloy; and (3) the exclusive rights to the use of the high-frequency coreless induction furnace (which has proved very satisfactory for melting nickel silver) for the wrought brass industry are controlled by one concern. A little over one year ago the first vertical ring induction furnace to be used for melting nickel silver in the Naugatuck Valley was placed in operation. This was followed by two more in the same mill, and by

Jan 1, 1930

By M. R. Pickus

THE study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centered cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystalliza-tion has not yet been filled was indicated by C. H. Samans,2 who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakao,4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers,6 were of a. qualitative nature. It is our hope that the present investigation may contribute some-thing to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1938

By Jesse O. Betterton, Y. E. Lebedeff

AS a matter of the most widespread interest to lead-refining metallurgists, the process of desilverizing lead originated by Parkes is the most fundamental step in lead refining. While this basic operation, in addition to effecting a practically complete recovery of gold and silver, is also a great purifying operation and a governor on the purity and uniformity of the final refined lead, it has the important deficiency that no bismuth is removed in the operation. The problem of finding a satisfactory, inexpensive method for removal of bismuth that would fit in with the basic desilverization step has been one of enticing interest for lead-refinery metallurgists for many years. Of late it has become one of imperative interest, and while many attempts and much progress have been made, it is probably fair to say that metallurgical progress thus far is only catching up with commercial requirements. The Pattinson process, an original competitor of the Parkes process for desilverization, has received much attention for its possibilities for bismuth removal. Bismuth concentrations in the Pattinson process fall far short of the silver concentrations and as a result too many operations are required and a crawl in grade in the kettle units is experienced which requires periodic correction. Altogether, it has proved too expensive a remedy, from the cost standpoint of both installation and operation. The Betts electrolytic process is a fully satisfactory remedy but its present status in the field of lead refining is more a matter of bismuth removal than preference as a refining system, except, of course, in instances particularly favorable to the basic requirements of the process. The Betts process, of course, is essentially different from the Parkes process, and very difficult to associate therewith to any economy except in minor ways. Accordingly, where economy dictates the Parkes process, and this is true of far the greater portion of the world's tonnage, the adoption of the Betts process primarily for bismuth removal is apt to prove an expensive remedy on account of its normally higher cost of operation, inelasticity of the equipment for variable tonnages, and high per ton cost of installation.

Jan 1, 1937

Discussion of the paper of S. E. Bretherton, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1481 to 1487. S. E., BRETHERTON, San Francisco, Cal.:-Since preparing my paper, our chemist, F. L. Wilson, has been experimenting with Leadville, Colo., oxidized zinc ore and Leadville zinc sulphides containing lead, operating upon 40-1b. lots at a time. His results on Leadville sulphides are as follows: The raw ore contained a trace of gold, 5.04 oz. of silver, 19.1 per cent of zinc, and 7.24 per cent of lead. After roasting the ore contained a trace of gold, 5.72 oz. of silver, 0.75 per cent of copper, 21.7 per cent of zinc, and 8.29 per cent of lead. The loss in weight by leaching was 38.8 per cent. The extraction was 42.8 per cent of the copper, 80.6 per cent of the zinc, 7.1 per cent of the lead, 0.64 per cent of the silver, and no gold. The little .silver that is extracted would be thrown down with the copper when precipitating it from the zinc and both thrown hack into the residue to be smelted. There would be no trouble in smelting the residue with nearly all the sulphur eliminated and containing less than 7 per cent. of zinc. On zinc carbonates containing silicates the results are not satisfactory. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :¬The paper by Mr. Bretherton upon the application of ammonia and carbonic acid to the recovery of zinc as oxide from roasted sulphide ore is of interest to me, as the first installation of the Schnabel process for the extraction of zinc from a mixture of zinc oxide, lead oxide (with some cupric oxide), and pellets of enriched lead, produced in steaming liquated zinc-silver-lead crust of the Parkes process, was made at Lautenthal, Harz mountains, where I was chemist. In that capacity I carried out numerous experiments on the Schnabel process, was active in the erecting of the plant, and later had charge of it. After the Lautenthal plant had been in operation for some time a similar one was built at Hoboken-les-Anvers, but both have been abandoned, as the wet process could not compete with the distillation of the liquated zinc-silver-lead crust, now used universally in the Parkes process.

Jan 11, 1913

By A. Kounosu, T. Fujita, J. Shimoiizaka, K. Nakatsuka

Stable aqueous dispersion of magnetite colloid of about 10 nm in diameter was obtained by allowing an anionic or nonionic surfactant to adsorb on the hydrophobic surface of magnetite particles prepared by monomolecular adsorption of oleate. Sodium dodecylbenzene sulfonate, sodium oleate and poly (oxyethylene) nonyl phenyl ethers whose hydrophilic-lipophilic balance (HLB) are higher than 12 were suitable for giving a second adsorption layer to obtain a stable dispersion. Stability of the colloidal suspensions depends upon pH of the solution and is controlled by the dissociation of the adsorbed surfactant in the second layer. The addition of ethyleneglycol, which was used for lowering the freezing point of the dispersion, did not affect the stability when used in amounts smaller than 60% of water. Preparation of diester-based ferrofluids was also attempted by the same procedure using a nonionic surfactant as second layer molecule. Hydrophobic magnetite colloid, which had been preliminarily coated with mono-molecular oleate, was suspended in di(2-ethylhexyl) agipate, azerate, and sebacate respectively, and dispersion stability was investigated by adding various poly (oxyethylene) nonyl phenyl ethers of different HLB values. It was found that those with HLB values between 10.9 and 13.3 were suitable for this purpose. Stabilities of the dispersions in a magnetic field were investigated up to 1 T by applying an electromagnetic field. No separation of dispersant was observed and each magnetite dispersion displayed the characteristics of a magnetic fluid.

Jan 1, 1980

By C. Norman Cochran, James L. Brandt

ALTHOUGH gas in aluminum and its effect on aluminum products have been the subject of a number of papers, not many quantitative determinations of the hydrogen content of solid aluminum and its alloys have been recorded in the literature. For solid aluminum samples, four investigators have reported hydrogen contents which appear reasonable compared with the hydrogen solubility of 0.7 ml per 100 g, STP, in molten aluminum at 660°C established by Ransley and Neufeld' and verified by Opie and Grant' and Ransley and Talbot. Sloman," who used a vacuum fusion procedure, reported the hydrogen content of some high purity aluminum as 0.66 ml per 100 g, STP. Griffith and Mallett, employing the tin fusion method, reported the internal hydrogen content of six different aluminum alloys as ranging from less than 0.1 ml per 100 g, STP, for 1100 alloy to 0.7 ml per 100 g, STP, for 4043 alloy (previously 43S, a 5 pct Si alloy). Eborall and Ransley," using a solid extraction of the gases at 600°C, reported hydrogen contents ranging from 0.1 ml per 100 g, STP, to 1 ml per 100 g, STP. Ransley and Talbot reported that several thousand analyses on 99.2 pct and higher purity aluminum as well as Duralumin type alloys indicated hydrogen contents ranging from 0.1 ml per 100 g, STP, to 0.5 ml per 100 g, STP.

Jan 1, 1957

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

By A. W. Gauger

Coal as mined contains varying quantities of inorganic components (mineral matter) which, on combustion, produce the residue known as ash. It has long been realized that the weight of this residue does not equal the weight of the mineral matter originally in the coal, because of the chemical changes that take place during the ashing process. Moreover, the ordinary ash analysis presents the ash as a mixture of oxides with little or no clue to the identity of the mineral species originally present in the coal. It is only for pyritic sulfur that an attempt is made to determine a mineral component. So far as the authors are aware, there are practically no experimental data in the literature as to the percentages of the different mineral species present in coal. The oft-quoted table of Marson and Cobb1 cannot rightly be considered as data, since the authors merely state that the table "shows the probable forms in which these ash constituents exist in coal." In view of the attempts to calculate analyses and determinations of the calorific equivalent of coal to the mineral-matter-free basis, as well as the importance of the mineral species in clinkering, combustion and coking, it seems strange that so few data are available on this phase of coal technology. For example, numerous empirical corrections for use in the scientific classification of coal have been suggested to compensate for the losses from the mineral matter during ignition of the coal to ash. These include multiplication of the ash percentage by various factors such as l 1/10 and 156, the use of the Parr unit coal formula (1.08 A + 22/40 S, where S = total sulfur) as well as certain modifications of the Parr formula that attempt to correct for the organic sulfur present in the coal. Although many experiments have been made to determine the loss on ignition of the clays associated with the coal measures and correction

Jan 1, 1934

The volumes of Transactions, which are published annually, contain the list of officers, rules, etc., the Proceedings, and the papers revised for final publication. (In this revision, after the preliminary publication, authors are permitted to use the largest liberty; and the changes and additions made in papers are sometimes important. It should be borne in mind by those who study or quote a paper in the preliminary edition, that they may not have in that form the ultimate and deliberate expression of the author's views. It should be added, however, that in the majority of cases there are no important changes.) These volumes are for sale as follows, in paper covers:

Jan 1, 1917

By J. L. Lamont, W. Crafts

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By W. Crafts, J. L. Lamont

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By H. N. Hall

Various factors must be considered in an engineering evaluation of gravity-drainage reservoirs. Among these are: (1) the effect of producing rate on total oil recovery; (2) the effect upon well productivity and ultimate recovery of the pressure level maintained during the producing life of the reservoir; (3) the economic advantage of full or partial pressure maintenance; and (4) estimate of the rate of gas production and injection and the possible purchase of gas under conditions of full pressure maintenance to ascertain compressor facilities needed. All of these factors can be evaluated only when a reliable method is employed for determining reservoir performance in gravity-drainage reservoirs. The purpose of this paper is to present a general method for calculating the performance of a gravity-drainage reservoir. This method is applicable for conditions of complete pressure maintenance, partial pressure maintenance and normal pressure depletion. Provisions are made to take into account variations throughout the reservoir of reservoir configuration, changes in permeability and fluid composition. Based on the method presented in this paper, an IBM 650 computer program has been developed. The past performance of an actual gravity-drainage reservoir producing under conditions of declining pressure and no gas injection was duplicated using this program. INTRODUCTION In tilted reservoirs the production of oil is influenced by drainage of oil from upstructure to downstructure locations. When this downstructure drainage of oil is sufficient to cause effective segregation of the gas and oil in a reservoir, the reservoir is usually classified as a segregation drive or gravity-drainage reservoir. (Discussion will be restricted to gravity-drainage reservoirs which have no encroachment of edge water.) The important feature in gravity-drainage reservoirs is the density difference between reservoir oil and gas. These phases tend to segregate in the reservoir with the result that in the gas cap the oil saturation is maintained at a higher level by drainage of oil from the gas-cap area. Oil can be produced from the oil zone at a low gas-oil ratio and reservoir energy is thereby conserved. The standard material balance in not adequate for predicting gravity-dramage reservoir performance because it does not take into account the difference in saturation above and below the gas-oil contact. Several authors'.' have presented methods for calculating the performance of gravity-drainage reservoirs in which reservoir pressure is maintained constant by gas injection into the gas cap. Using some simplifying assumptions, these methods can be employed with a desk calculator to give acceptable results. The problem of predicting the performance of gravity-drainage reservoirs under the conditions of declining reservoir pressure is many time more complex than that of constant pressure. fierefore, attempis to develop a method suitable for desk calculation have required excessively simplified assumptions. In the past several years, highspeed digital computers have become more widely available for reservoir engineering problems. These corn puters are well suited to problems such as the prediction of the performance of gravity-drainage reservoirs with pressure decline. Many of the simplifying assumptions necessary for hand computation can be eliminated so that a realistic approach to the gravity-drainage process can be made. CONCEPTUAL PICTURE OF OIL MOVEMENT IN GRAVITY-DRAINAGE RESERVOIRS Before attempting to develop an analytical treatment for conditions occuring in a gravity-drainage reservoir, a concept should be formed concerning the movement of fluids in the reservoir as oil is produced. A review of the literature'.' shows that it is customary to classify gravity-drainage operations into two categories—(1) with complete pressure maintenance, and (2) with declining pressure. The same line of reasoning will be followed in presenting the concept of the movement of fluids in the reservoir because it is easier to visualize the movement of fluids under conditions of complete pressure maintenance. After discussing complete pressure maintenance, an analogy will be made between that and the case of declining pressure. It should be kept in mind throughout that the final aim for the problem of solving gravity-drainage performance with digital computers will be to develop a general program for any kind of gravity-drainage reservoir. COMPLETE PRESSURE MAINTENANCE One feature which is generally common in gravity-drainage reservoirs is a gas cap located at the top of the structure. This is shown in Fig. 1(a). Fig. l(b) shows oil saturations that might occur through the reservoir. In the gas cap, oil saturation is lower than

By C. M. Schwartz, A. E. Austin, W. B. Wilson

High-temperature X-ray diffraction studies were conducted with Th-U alloys with up to 10 wt pet U. The solid solubility of uranium in thorium as a function of temperature was determined by the method of lattice parameters. Thorium will dissolve up to 2.5 wt pet U at 950°, 4.5 wt pet U at 1150°, and 7.5 wt pet U at 1250°C. Determinations were made of the temperature of the transition of thorium and of the effect of uranium upon the transition. The a to ß transition for thorium was observed to occur at 1330' ±20°C. Mean coefficients of expansion were calculated for thorium and two alloys, and for ThO2 in contact with the thorium, using X-ray lattice-parameter data. Values obtained at 950° C for thorium and Tho2 were 12.1 and 9.40 X 10-6 per OC, respectively. Impurities obtained during the X-ray exposure were identified by diffraction and were essentially Tho2 and ThC, with two additional unknown phases being detected. The effect of the impurities upon the results is discussed. DIRECT investigation (i.e., high-temperature X-ray diffraction studies) of the phase diagram of thorium-rich uranium alloys has been shown to be necessary since recent work1 - has disclosed the presence of an allotropic transformation near 1400°C in pure thorium with the room temperature face-centered-cubic phase transforming to a body-cen-tered-cubic structure at the elevated temperature. The effect upon the transition of the addition of uranium to thorium and of the solubility of uranium in thorium at high temperatures remained unknown, yet was of interest in understanding fabrication procedures and elevated temperature use. The present work was undertaken to provide information in this area by determining the transition temperature, the effect of uranium on the transition temperature, and the solubility of uranium in thorium as a function of temperature. Experimental Work The high-temperature diffraction data were obtained using a camera especially designed for the purpose3 and capable of reaching temperatures in excess of 2000°C at pressures as low as 1 x 10." mm Hg. Temperature regulation was provided by regulating the power input to ±0.1 pet variation, and by regulating the water flow through the camera jacket to provide a constant thermal load. The X-ray sample was a rod nominally 80 mil diam, which was further turned down to 20 mil and then etched to 18 mil over 1/2 in. of one end. This was placed in the sample holder and mounted on the camera so that the smaller part was surrounded by a cylindrical tantalum-sheet radiation-type heating element. Diffraction from the sample was recorded on film after passing through a slot in the heating element and radiation-baffle shield and through beryllium vacuum windows. The X-ray film mounting was of the Straumanis type4 with a camera diameter of 114.59 mm. Since previous work of Chiotti' indicated that impurities considerably alter the transition temperature, chemical analysis of the arc melted iodide crystal-bar thorium samples was obtained prior to testing. The analysis disclosed the material to contain as low as 0.001 ±0,0002 wt pet H and 0.007 ±0.001 wt pet 0. Carbon was 0.003 wt pet and nitrogen less than 0.002 wt pet. This material was sealed in mild steel in an inert atmosphere and subsequently hot rolled to 3/8-in. diam rods at a temperature of 732°C. Following removal of the jacket, the material was pickled and cold swaged to 1/8-in. rods, from which the diffraction samples were prepared. The alloys were similarly prepared, with the uranium being added during arc melting. The uranium analyses of the alloys prepared appear in Table I. The experimental procedure for diffraction examination of the three samples of high-purity thorium differed from those of the Th-U alloys. The original practice, later modified, consisted of pumping down the camera with the diffusion pump on and then admitting liquid nitrogen to the cold trap of the system. This was modified for the Th-U alloys by maintaining liquid nitrogen in the cold trap at all times before and while the diffusion pump was heated. This minor change produced a reduction in the amount of carbon pickup by the sample during exposure to the diffusion-pump vapors. The sample was brought to the desired test temperature and exposed for 21/2 hr at pressures which were usually 2 x 10-6 mm Hg, or lower. Exposures were made at

Jan 1, 1959