Search Documents

By Charles D. Borror, George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By George K. Foster, Charles D. Borror

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By John A. Church

IT is a well-known fact that under similar conditions a ton of pig iron can be made from any ore with less fuel when charcoal is used than when coke or anthracite is employed for heating. The cause of this superiority is entirely undiscovered, and no explanation has yet been offered which has won even temporary acceptance. Such as they are the hypotheses heretofore presented are of two general kinds, and they come from those two divisions of the working force which are so often antagonistic in all professions, the scientific and the practical men. The theory of the scientific men is drawn from the chemical reactions which are known to go on in the furnace, and it is well expressed in a recent paper by Prof. Akerman, of the Stockholm (Sweden) School of Mines. It makes the superiority of charcoal as a fuel in the blast furnace to depend upon its quick and thorough reduction of carbonic acid. This property belongs to charcoal in virtue of its porous structure. Its cells have a diameter of only one twenty-four hundredth of an inch, and one grain of charcoal has been computed to have a surface of two and four-tenths square feet. According to the theory in question, carbonic acid is formed by the first impact of the air upon the fuel; but in charcoal furnaces the acid is immediately reduced to oxide by taking the necessary amount of carbon into combination, and the gas reaches its highest reducing power even in the near vicinity of the tuyeres. Coke, being harder, does not produce so strong a reducing gas in that part of. the furnace. Carbonic acid is formed as in the case of charcoal, and remains longer before its reduction to oxide is completed. Anthracite is the

Jan 1, 1879

By R. Hadfield

Last year this institute was good enough to accept some remarks by the writer regarding sound steel, entitle Plant for Hadfield Method of Producing Sound Steel Ingots…

Jan 1, 1915

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By F. T. Selleck, H. H. Reamer, B. H. Sage

An experimental investigation was made of the effect of temperature upon the three-phase pressure associated with the propane-water and propene-water systems when hydrates were present. In addition, the characteristics of the propane-propene-water system were established over a limited range of ternperatureo under conditions such that hydrate was formed. The hydrate phase for this system may he a solid solution and the distribution of propane and propene in it is similar to that found in the coexisting hvdrocarhon liquid phase. INTRODUCTION A knowledge of the characteristics of hydrates of the hydrocarborrs encountered in industrial practice is of importance in connection with the design of process equipment. Villardl.1,2 carried out early studies of hydrates, and de Forcrand1 con-sidered the more probable compositions of the hydrates of hydrocarbons. Hammerschnid1 presented information about the propane-water and the isobutane-water systems. Scheffer5 studied the hydrate of hydrogen sulfide in detail, and de For-crand reported on the hydrates of krypton, argon, and xenon.1 Roberts and co-workers1,2 determined the nature of the hydrates formed in the methane-water and ethane-water systems. Carson and Katz10 studied the methane-propane-water, methane-pentane-water, and the methane-hexane-water systems in the four-phase region. The results of this rather extensive investigation indicated that the paraffinic hydrates formed solid solutions. The experimental evidence now available does not Support the existence of hydrates of the pentanes-antl-heavier hydrocarhons but it cannot be stated with certainty that such hydrates are not formed. Stackelherg. 11,12,13 made extensive studies of the crystal structure of paraffinic hydrate; by means of x-ray techniques and found that hydrates poses; a definite structure and composition. The existence of such a Structure does not preclude the firmation of Solid solutions of hydrates in aqueous systems containing two or more hydro-carbon~. Wilcox, Carson and Katz" reviewrd the information on the hydrates of importance in the processing of natural gas and presented data concerning their formation from natural gas. Kobayashi and Katz1' made studies at high pressure of the Hydrate of methane. and Unruh and Katz"' investigated hy-drates in mixtures of carbon rlioxide and methane. Frost and Deaton contributed to the knowledge of the composition of the paraffinic hydrates The irregularities in the experimental results were several times the expected uncertainties. This experience confirms the behavior encountered by other investigators indicating that hydrates tend to occlude water during their formation, thus rendering difficult the direct measoremeut of their composition. Miller and Strong2 investigated a number. of paraffinic hydrates from the standpoint of their possible application to (, the industrial storage of gas. Powel1 studied the effect of solutes upon the decomposition temperature of paraffin hydrates. Marked lowering of the decomposition temperature at a given pressure may he obtained by the use of such additive agents as ethylene glycol, urea. and sodium chloride. APPARATUS AND METHODS Two method* were here employed to study the behavior of hydrates. The first involved a glass capillary within which the hydrocarbons and water were confined over mercury. The second made use of a double-ended weighing bomb technique." The glass capillary equipment has been described elsewhere.'" A schematic drawing of it is presented in Fig. 1, where the arrangement of the agitator and mercury reservoir is shown in some detail. The lower part of the glass capillary, D, was enlarged to afford space within which the fluids used in the investigation could he stored at low pressures after their introduction through the valve. G. The temperature of the capillary was controlled by the circulation of a hydrocarbon oil of low viscosity from the agitated bath, B, through the vacuum jacketed column. C. The pump, A, was employed for the circulation of this oil. A relatively clear view of the capillary tube, D, was obtained through the vacuum jacket. Mercury was introduced into the lower part of the vessel, E, from

Jan 1, 1952

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joshua I. Tracey, Mackenzie Gordon

THE bauxite deposits in central Arkansas were formed by weather¬ing, in early Eocene time, of fresh or kaolinized nepheline syenite above the water table in a subtropical climate of fairly continuous moisture. Four types are recognized: (1) residual bauxite deposits on kaolinized nepheline syenite, (2) residual deposits on kaolin and bauxite detritus, (3) alluvial deposits of sorted pebbles and pisolites of early Wilcox age, and (4) rubble deposits of later Wilcox age. All were invaded by kaolin and siderite during subsequent burial by Eocene sediments. PART I-FIELD RELATIONS OF THE DEPOSITS The Arkansas bauxite region for years has produced about 95 pct of the domestic supply of bauxite of the United States and it contains today reserves of more than 40 million tons-nine tenths of the known domestic reserves. During World War II, the Arkansas bauxite deposits were explored jointly by the U. S. Geological Survey and the U. S. Bureau of Mines. Some 6000 holes were drilled by rotary rigs under contract to the Federal Govern¬ment, which resulted in the discovery and delimiting of approximately 20 million tons of ore in place. Detailed study of the many sections cored through the bauxite, of data from a much greater number of drill holes made available by all the operating companies, and of the extensive mine faces exposed in the strip pits, has yielded valuable geologic information about the origin of the deposits. It is now possible to piece together a paleotopographic picture of the deposits and the now-buried land surface on which they formed. The bauxite region in the center of Arkansas (Fig 1) contains two producing districts: one in Pulaski County, just south of Little Rock, and the other in Saline County, about 15 miles to the southwest. The deposits in both districts are associated with hills of nepheline syenite, bosses of a large batho¬lith that was intruded into Paleozoic rocks and later buried beneath coastal plain sediments deposited during Cenozoic time. The folded Paleozoic rocks are exposed in the northwest half of the state and are covered in the southeast half by the nearly flat-lying coastal plain sediments. The older rocks were intruded by nepheline syenite, probably in Late Cretaceous time, and sub¬sequently were eroded so as to expose the top of the batholith. In Paleocene time, marine limestone and laminated black silty clay of the Midway group were deposited in an advancing sea, and covered all but the most elevated parts of the batholith. Erosion of the islands of nepheline

Jan 1, 1952

By Clarence Zener

IT is customary to regard the stress-strain relation as consisting of two parts, the elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.1,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwirkung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants-e.g., Young's modulus upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of an elasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1946

By AIME AIME

THIS year the Petroleum Division holds its fall meeting at Houston, Texas, Oct. 2 and 3, with head- quarters at the Lamar Hotel. Technical sessions will be held in the morning and afternoon of both days. A smoker on Friday afternoon will afford an opportunity to get together socially. Saturday evening is left free for private parties to the beach at Galveston, where a wide variety of entertainment is available. On Oct. 4 there will be an excursion to Sugarland oil field, with luncheon at Boling and a visit to Boling sulfur mine and plant in the afternoon. There are nine technical papers on the program for Friday. Saturday morning will be devoted to oil production control and it is planned to make the discussion more

Jan 1, 1931

By Bernard H. Coyle, Robert N. Anderson, Judith A. Koperski

Between 6 and 8 million cars are shredded annually in the U.S. This shredded material is magnetically separated leaving a mixture of nonmetallics and nonferrous metals which can be further separated into its metallic and nonmetallic constituents. The metallic portion is a mixture of metalr; and alloys containing predominately zinc, and some aluminum, copper, and residual iron. Hydrometallurgical strategies are proposed for recovering the aluminum, copper, and zinc. The thermodynamic and kinetic behavior of the most promising alternatives to separation are discussed.

Jan 1, 1978

By M. Sheffield

This paper presents a technique lor predicting the flow of oil, gas and water through a petroleum reservoir. Gravitational, viscous arid capillary lorces are considered, and all fluids are considered to be slightly compressible. Some theoretical work concerning the fluid flow in one-, two- and three-space dimensions is given along with example performance predictions in one- and two-space dimensions. INTRODUCTION Since the introduction of high speed computing equipment, one of the goals of reservoir engineering research has been to develop more accurate methods of describing fluid movement through underground reservoirs. Various mathematical methods have been developed or used by reservoir engineers to predict reservoir performance, 193-5,7,8 The work reported in this paper extends previously published work on three-phase fluid flow (1) by including a rigorous treatment of capillary forces and (2) by showing certain theoretical mathematical results proving that these equations can be approximated by certain numerical techniques and that a unique solution exists. DISCUSSION The method of predicting three-phase compressible fluid flow. in a reservoir can be summarized briefly by the following steps. 1. The reservoir, or a section of a reservoir, is characterized by a series of mesh points with varying rock and fluid properties simulated at each mesh point. 2. Three partial differential equations are written to describe the movement at any point in the reservoir of each of the three compressible fluids. All forces influencing movement are considered in the equations. 3. At each mesh point, the partial differential equations are replaced by a system of analogous difference equations. 4. A numerical technique is used to solve the resulting system of difference equations. Capillary forces have been included in two-phase flow calculations.1,4,8 The literature, however, does not contain examples of prediction techniques for three-phase flow that include capillary forces. Where capillary forces are considered, each of the three partial differential equations previously discussed has a different dependent variable, namely pressure in one of the three fluid phases. Therefore, three difference equations must be solved at each point in the reservoir. Where large systems of equations must be solved simultaneously, an engineer might question whether a unique solution to this system of equations actually exists and, if so, what numerical techniques may be used to obtain a good approximation to the solution. It is shown in the Appendix that a unique solution to the three-phase flow problem, as formulated, always exists. It is also shown that several methods may be used to obtain a good approximation to the solution. The partial differential equations and differenceequations used are shown in the Appendix. Matrix notation has been used in developing the mathematical results. Two sample problems were solved on a CDC 1604. They illustrate the type of problems that can be solved using a three-phase prediction technique. SAMPLE ONE-DIMENSIONAL RESERVOIR PERFORMANCE PREDICTION A hypothetical reservoir was studied to provide an example of a one-dimensional problem that can be solved. Of the several techniques available, the direct method of solution as shown in the Appendix was used. The reservoir section studied was a truncated, wedge-shaped section, 2,400 ft long, with a 6' dip. (A schematic is shown in Fig. 1.) This section was represented by 49 mesh points, uniformly spaced at 50-ft intervals. The upper end of the wedge was 2 ft wide, and the lower end was 6 ft wide. The section

Jan 1, 1970

By S. H. Ash

More than 100 minerals are mined and processed in the U. S. Management and labor have negotiated wage-scale agreements that have balanced wages and affected cost of labor in such a manner that comparisons can be made of transportation costs. Transportation of materials underground has become of vital importance. This report describes underground haulage methods and equipment, presents cost analyses, and discusses future plans for underground transportation in metal mines. It does not cover hoisting in shafts or slopes by cage, skip, or cars. Advancements have been made by the metal mining industry in lowering transportation costs in several mines, making it possible to mine orebodies or portions of orebodies not considered economically recoverable a few years ago. Numerous reports have been written on transportation at metal mines; this report covers recent haulage at some representative mines throughout the U.S. The term metal mine is used to include all noncoal mines from which up-to-date information was obtainable.

Sep 1, 1956

By Robert Henderson

SEVERAL very interesting articles have been written on the caving system of mining, but most of these papers have dealt separately with the slusher system or the chute and grizzly system. In this paper, a comparison will be made of the two methods, both of which are being used at the Climax mine. The mine is on the Continental Divide, in central Colorado, at an altitude of approximately 11,500 ft. above sea level. The long, cold winters, characteristic of the high Rockies, create a number of operating problems not usually found in other mining areas. THE ORE BODY The Climax ore body is just east of the Mosquito fault. This structural deformation has brought the granite on the east against the sedimentary rocks on the west. The ore occurs in an intensely altered granite and schist around a silicified granite core. The ore is in a highly fractured zone of moderate silicification. The principal mineral, molybdenite, is found in these fractures. Barren dikes of granite porphyry cut through the ore body and core with no apparent regularity. The grade of the ore is fairly uniform and gradually decreases toward the footwall core and also into the hanging-wall granite. The footwall and hanging wall are determined entirely by assays. The ore body is roughly dome-shaped, with the apex truncated at the surface. It is covered to varying depths with talus. A horizontal section of the ore body on the Phillipson level appears as an annular ellipse surrounding the footwall core. The ring of ore varies in width from 300 ft. to as much as 800 ft. The north-south axis of the core is about 1200 ft. and the east-west axis is about 1800 ft. In the ore zone, the rock is sufficiently strong to maintain reasonably large openings, and openings larger than haulage drifts usually have to be supported. The ore is cut by a great many fractures and shears and breaks into rather large blocks when caved, necessitating considerable secondary blasting. The waste that overlies the ore body breaks relatively fine in comparison with the size of the blocks of the caved ore and tends to run through the broken ore in the cave, causing dilution unless the draw is carefully controlled. MINING SYSTEMS For several years the ore was mined by the chute and grizzly system, a system that differs from that used in other caving mines only in the size of openings and equipment. In the chute and grizzly system, main haulage laterals were driven along the footwall core and also along the

Jan 1, 1944

By A. Taylor

NICKEL-RICH alloys hardened with small additions of titanium and aluminum and centered around that region of face-centered-cubic primary solid solution, 7, where the atomic ratio of nickel chromium is about 3 to 1, form an important series of high temperature materials because of their resistance to oxidation, high temperature strength, and excellent creep characteristics at elevated temperatures.' With suitable heat treatment it is possible to precipitate a phase based on the ordered face-centered-cubic y' phase, Ni,,Al, from the randomly ordered nickel-rich y face-centered-cubic primary solid solution. By adjusting the ratio of aluminum to titanium the precipitation of needles of the hexagonal intermetallic compound n-NiaTi may be effected. In the present investigation, the main interest was focused on the interrelationships among the y, y, and 7 phases. By using alloying elements of high purity and a suitable melting technique the presence of carbides and nitrides could be completely obviated, although it is realized that their presence is probably essential in alloys of commercial importance. As a preliminary to the study of the Ni-Cr-Ti-A1 system, it was necessary to establish the constitutional diagrams of the three contiguous systems, Ni-Cr-Al, Ni-Ti-Al, and Ni-Cr-Ti, which together form the nickel-rich corner of the Ni-Cr-Ti-A1 quaternary tetrahedron. Accounts of this work on the ternary systems have already been published by the author. A preliminary disclosure of the author's investigations on the ternary and quaternary systems has been made by Hignett2 and has since stimulated work in the same field by Nordheim and Grant." Before the detailed account of the quaternary system, a brief description will be given of the three contiguous ternary diagrams on which it is ultimately founded. Ni-Cr-Ti System The 750° and 1000°C temperature isothermals of the Ni-Cr-Ti system as determined by Taylor and Floyd' are shown in Figs. 1 and 2. The single phase fields of greatest interest are occupied by the extensive face-centered-cubic y primary solid solution of chromium and titanium in nickel, and the close-packed-hexagonal Daltonide, n-Ni3Ti, from which tie-lines radiate across the very wide y+n two-phase field. The chromium-rich primary solid solution is represented by a. As may be seen from the diagrams, the extent of the y phase field increases quite appreciably as the temperature is raised from 750" to 1000°C. Isoparametric lines for the y phase are shown in Fig. 1. They are interesting in that they are almost parallel to the y/r+n boundary. Thus the determination of the tie-line directions is entirely dependent on the exact stoichiometry of composition of the 7 phase. Ni-Ti-Al System The 750°C isothermal section of the nickel-rich portion of the system Ni-Ti-A1 as determined by Taylor and Floyd is shown in Fig. 3.' The regions of greatest interest are the extensive y primary solid solution of titanium and aluminum in nickel, the y' Berthollide phase field based on the ordered face-centered-cubic structure of Ni3Al, and the hexagonal Daltonide phase, n-Ni3Ti. As may be seen from Figs. 3 and 4 the area occupied by the y phase is substantially the same at 750°C as at 1000°C, but the area of the 7 phase is considerably greater at the higher temperature. The tie-lines radiate from n-Ni3Ti across the y+v and y' + v two-phase fields and are evenly distributed

Jan 1, 1957

By F. C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of transporting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion. FIXED-SOURCE METHODS Essentially, a fixed-source method consists of the measurement of electromagnetic fields about the source. The mutual coupling between the source and the earth is constant, but the mutual coupling between the receiver and the earth (unless the earth is homogeneous) and also between the source and the receiver changes at each station. The results are usually normalized by relating the field data to the calculated free space or primary field. Turam and Radio Reference Signal Methods: The turam or two-frame* (see Fig. 1A) is probably * Turam means two-coil. the most common fixed-source method. The energizing source is an insulated cable grounded at both ends or formed into a large rectangular loop. Measurements are taken along a traverse at 5 to 50-meter intervals using two small receiving coils, the lagging coil being placed at the position previously occupied by the leading coil. The complex ratio (i.e., inphase and out-of-phase ratios) of the voltages induced in the two coils is measured. Operating frequency range is about 100 to 800 cps. In a typical turam survey a straight, grounded cable several kilometers long is laid out parallel to the probable strike of the ore deposits or conducting strata being sought. An area extending 1 or 2 km on each side of the cable, and within 1 or 2 km of the ends of the cable, is surveyed. Measurements are made at stations 5 to 25 m apart along traverses perpendicular to the cable. Measurements may be made along lines parallel to the cable to serve as base lines for the traverses or for other special purposes. Commonly the receiving coils are oriented with their planes horizontal so that only the vertical component of the field is measured. If additional information is required, one of the hori- zontal components may also be measured by orienting the coils with their planes vertical. In a modified turam technique developed recently for both ground and airborne measurements (Fig. 1B) the amplitude of the complex voltage induced in a single receiving coil is measured and its phase compared with that of a reference signal transmitted from the energizing system by a radio frequency carrier. Thus the un-normalized field is obtained directly, whereas with the turam method it is obtained by calculation from the ratios. The turam method and its modifications have a greater working depth than the other electromagnetic procedures used in ore prospecting. Under favorable conditions conductors have been located at depths of 200 to 300 m. A modified turam method with one of the electrodes grounded in the upper end of a plunging orebody was used to follow the extension of this body to a depth of 200 m beneath a layer of conducting schists. Straight grounded cables are usually preferred to insulated loops because they are easier to lay out and because they often make the method more sensitive. The greater sensitivity of a grounded cable is a result of ground return currents which may flow in the orebodies in addition to the eddy currents caused by induction from the current in the cable. Anomalies in the vertical field due to eddy currents are characterized by a correspondence between high values for the inphase component and positive out-of-phase components and/or low values for the inphase component and negative out-of-phase components. Also the inphase component may approach zero, but it does not become negative. In very long continuous conductors that are parallel to a grounded cable the effect of ground return currents may far exceed the effect of eddy currents. These ground return currents cause a lack of correspondence between the inphase and out-of-phase components and may cause negative inphase or anti-phase components. It becomes difficult to carry out the measurements and often difficult to interpret the results. Such results immediately suggest the presence of graphitic strata, however, since ore deposits are rarely extensive enough to accumulate sufficient ground return current to cause these results. A cable laid out perpendicular to the strike or an insulated loop is sometimes used in areas where graphitic schists and slates are present. Anomalies are then completely or almost entirely due to eddy currents and are easier to interpret. The measured voltage ratios are normalized by either subtracting or dividing by normal field ratios calculated from free space considerations. The normalized ratios are then plotted as individual profiles. When significant anomalies occur in the ratio measurements, the actual normalized fields are calculated by beginning with a measured or an assumed value for the field at a point near the cable and successively multiplying this value by the normalized ratios. There is a similarity between this process and a numerical integration of the ratio curve. Conversely, in many respects the ratio curve is similar to the first derivative of the field curve.

Jan 1, 1960

By Charles T. Holland

IN connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter [ ] into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. STRENGTH OF COAL It is generally agreed that one of the necessary conditions for bumps is a strong [ ] coal.1 Therefore, since the strength of coal is an important factor, a study of this property should be made. Several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines8 and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semibituminous (Pocahontas No. 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the same coal.

Jan 1, 1942

By Charles White Merrill, James W. Pennington

No metallurgical process developed in the 20th century compares with froth flotation in its effect on the mineral industry. Processes like gravity - concentration, amalgamation, and pyrometallurgical reduction are of ancient origin; others like cyanidation and electrolytic reduction were well established by 1900. Such metallurgical processes as heavy-media separation, ion-exchange, and solvent extraction belong to this century, but their influence is small compared with froth flotation. Data collected by the U. S. Bureau of Mines* in a canvass of 202 froth flotation plants reveal that, in 1960, 198- million tons of material was treated to recover 20-million tons of concentrates which contained approximately $1 billion in recoverable products. SIGNIFICANCE OF FLOTATION Froth flotation as described in this chapter refers to a wet process for separating properly ground mineral particles into two or more products. It involves the separation of mineral particles from each other in a liquid pulp by means of air bubbles. Finely crushed ore is agitated in water with the addition of air or other gases. Various chemicals and oils are added to cause the selected mineral particles to attach themselves to the air or gas bubbles. These bubbles, carrying the mineral particles, rise to the surface where they are removed in a froth, while the other particles remain suspended in the pulp. The earliest flotation divided the raw material into two products: a bulk concentrate that was removed as a froth and a tailing that remained in the flotation machine. The froth usually contained the valuable constituents. The successful application of such a process depended on the recovery of a single concentrate from which one or more valuable constituents could be recovered by a chemical or smelting process. With the advance of the art, however, the principle of selective flotation, by which two or more relatively pure products could be recovered from complex raw materials, was evolved. Other chapters in this volume describe the developments during the last 50

Jan 1, 1962