Search Documents

By J. D. Rice, S. C. Pitzer, C. E. Thomas

Interpretation of pressure build-up data obtained in the conventional manner has often been difficult because of the deviation from theoretical behavior. Major causes of this deviation have been attributed to damage and afterflow, and to fluid redistribution in the wellbore which, in extreme cases, can result in a pressure hump in the early portion of the build-up curve. Theoretical investigations show that bottom-hole pressure is definitely influenced by phase redistribution in the tubing column during surface shut-in tests, and that the magnitude of the effect is sensitive to the producing gas-oil ratio and stabilized rate of flow in the well. For field experiments a wire-line tubing packer, which can be run in the tubing against a stabilized flow rate, was developed for bottom-hole shut-in tests. By use of this bottom-hole .shut-in method, pressure humps previously observed in surface shut-in tests were completely eliminated and the effects of afterflow minimized. Analog and digital computer studies have been made to obtain theoretical curves for comparison with field curves, and remarkable agreement between the results of bottom-hole shut-in tests and theoretical curves has been obtained. INTRODUCTION Pressure build-up data from shut-in wells have been used by the petroleum industry to determine the permeability of the formation, to estimate wellbore damage, to evaluate the static reservoir pressure and to speculate reservoir volume. Calculation of these factors is based on methods of analysis developed for theoretical systems whose build-up curves have a charac- teristic shape when the wells are shut-in at the sand faCe.1,2,3,5,8,10 However, field curves obtained by conventional surface shut-in methods do not always exhibit this characteristic. Such factors as stratification, rock heterogeneities and irregular reservoir geometry can cause the character of a build-up curve to deviate from that predicted by theory for a simple system. In addition, all field build-up data are affected by the methods utilized in obtaining the measurements. Conventional surface shut-in techniques allow two effects to occur which contribute directly to the manner in which pressure builds up at the sand face. The first, afterflow, has been recognized for some time and methods are available for estimating the magnitude of its effect and for correcting its influence.' The second, phase segregation in the tubing column after shut-in, has been reported only recently and appears to exert a considerable influence on the character of field build-up curves.!' In extreme cases, phase segregation can produce "pressure humps" in the early portion of the build-up curve. Such curves have been considered anomalous and have defied analysis. It is the purpose of this paper to discuss the effect of phase segregation in the tubing string during build-up and to present a bottom-hole shut-in technique for obtaining field build-up data which minimizes the influence of afterflow and eliminates phase segregation effects. It will be shown that reliable reservoir information can be calculated from build-up measurements obtained using this method, even though conventional surface shut-in tests on the same wells yield anomalous data. DISCUSSION OF PHASE REDISTRIBUTION EFFECTS Some of the effects of phase redistribution on pressure build-up curves have been described previously by Matthews and Stegemeier" who have presented evidence that phase segregation is responsible for the pres-

By D. F. Malott

The Michigan Dept. of State Highways makes extensive use of geophysics for subsurface surveying which would be applicable for uses in other fields. Examples of resistivity surveys are given which include a proposed large-volume excavation with suggestions for land use after excavation, subsurface evaluation for engineering design, and a subsurface survey for land appraisal. An example of a combined refraction seismic and resistivity survey is shown where the resistivity is used for outlining the unconsolidated soils, while the seismic method is used to outline bedrock and to evaluate it for rippability. A refraction seismic survey at the bottom of bridge caissons for evaluation of bedrock uniformity and a rehtive aid in assessing rock strength is reported. These past several years have been a period of unprecendented construction and commercial expansion. Vast private manufacturing complexes and government road, power, and office projects are being built or are in planning stages. Nearly everywhere, municipalities are expanding outward and upward. Many towns are developing into cities and many cities are displaying new skylines, and the building boom shows little sign of slowing down.

Jan 1, 1970

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Strain-induced porosity has been found to occur in titanium and other materials at tensile strains greater than the uniform elongation of the material. Porosity in titanium increases with increasing strain and temperature, being most severe at 300° to 800°F. Strain-induced porosity is believed to be a normal part of the mechanism of deformation in ductile materials. DURING the past few years there have been numerous references to the occurrence of voids in laboratory test specimens of metals subjected to strain.l-7 These voids have been referred to as intercrystalline cracking, strain-induced porosity, intergranular cav-itation, voids, and porosity. They appear to occur at grain boundaries or interfaces, and are generally associated with large amounts of strain and have been found mostly in creep specimens and to a lesser extent in tensile specimens. Because the phenomenon does not occur unless the material has been strained,

Jan 1, 1960

By K. W. John, L. Mueller

The rock mechanics approach to stability problems of steep rock slopes dealt with in this article has particular reference to the concept and methods of analysis developed by the Salzburg, Austria, school of rock mechanics. These theories are based on the principal postulate of the anistropy of the technological properties of in-situ rock masses. The present approach, which is more in line with geological engineering concepts, differs distinctively from the soil mechanics and engineering geological concepts commonly practiced in the United States. PRINCIPAL ENGINEERING APPROACH TO GEOTECHNICAL PROBLEMS AVAILABLE ENGINEERING CONCEPTS At the present time two different concepts are available for engineering analysis of underground structures and foundations in different earth material: soil mechanics and rock mechanics. Of these two branches, soil mechanics is, after 40 years of initially revolutionary and more recently evolutionary development, well established. Its principal concept of replacing in-situ soils or rock masses by perfectly homogeneous substitues has resulted in many practicable methods of analysis which, if applied with judgement, have resulted in successful applications throughout the world. Conversely, rock mechanics is still in the early stages of revolutionary development. Few, if any, standard concepts or methods of analysis have been established. Opinions vary widely. At present the professional background of an investigator very often determines the engineering concept to be applied to a particular problem, rather than its actual requirements if considered objectively. This paper stresses the rock mechanics or geological engineering point of view advocated by the Salzburg group. A review of the soil mechanics concepts is considered beyond the scope of this paper. THE "SALZBURG APPROACH" TO ROCK MECHANICS The rock mechanics concept as outlined here was initiated by Stini, based upon work by sander.1 Since

Jan 1, 1963

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis' in graphical form. In 1953 Fatt' also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie' equation, and the more general Winsauer equation', where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

By J. B. Clark

In multiphase ternary diffusion studies, plots of the variation bf the composition on the isotherm constitutes one of the most effective methods of presenting experimental results, especially if such plots are made in a manner which relates the composition path on the isotherm with the diffusion layer structure in the couple. Unfortunately, if different conventions for plotting are used serious misinterpretations occur readily, causing apparent disagreement between investigators who actually share the same viewpoint. A common convention for mapping these diffusion paths is needed at this time because with the increasing use of the electron-probe X-ray microanalyzer, a much greater number of ternary diffusion studies can be expected in the near future. In an effort to prevent unnecessary confusion in the future litera- ture, a convention for these plots is proposed, as outlined below. A hypothetical example of the use of these conventions is given in Fig. 1 where the path of composition through the diffusion structure of the 100 pct A/50 pct B, 50 pct C couple is plotted on the appropriate isotherm of the ABC system. The lower case letters relate the region in the diffusion layer structure to the appropriate composition on the ternary isotherm. 1) The diffusion path is plotted on the isothermal section corresponding to the diffusion temperature of the couple. 2) The terminal compositions of the plotted diffusion path are the initial compositions of the couple halves—provided infinite boundary conditions are maintained. If, in either couple half, infinite conditions are not maintained, then the path terminates at the composition of the exterior surface of the couple. If, at this surface, the composition varies with time or if the plotted path is time dependent, then the diffusion time should be noted beside the plotted path. 3) A solid line crossing a single phase field (e.g., line a-b in Fig. 1) denotes an existing layer of that phase in the diffused couple. 4) A dashed line crossing a two-phase field parallel to the tie lines (e.g., line g-h) represents an interface between the two phases with interfacial compositions designated by the ends of the tie-line. The line represents no spatial extent. 5) A solid line crossing a two-phase field so as to cut tie lines (e.g., line b-c or line j-k) represents a locally equilibrated columnar two-phase layer. The solid line should cut those tie lines which correspond to the lateral interfacial equilibria along the columnar

Jan 1, 1963

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By J. R. Kyte, L. A. Rapoport

The material balance equation for partiai or complete 1:trter-drivc reser1,oir.s been re-arranged to include a pressure irrferferencr ternr. This pressure interfernce term was ohtained from the theory established hy Morinda. A .successful progranl deissed to solve the resrclritlg c,qrration in a few hours on a nleelitr .sizeti, digital compuier. No prior knowdelge of the properties of the eqrrifer is required in the solution. 7' ri~rl calculations areatle using various assumed con!binuiions of value of the constant expretsing the qquifer properties correspoinds to the best fit ohtained between observed and calculated field history. Details of the method of calculaion are illus trated by an example. INTKCDUCTICN A method 01' calculating the material balance equation for a partial water-drive reservoir completed in an aquifer has been described in the literature." Pressure interference i'rc,m other pools iocated in the same nquiucr is not taken into account in this solution. When present, the pres- sure interference effect must be included in order to make a complete performance analysis. A correction for this effect has been developed using the theory cstahlished by Mor-tada.' Manual calculation of the material balance for water-drive reservoirs is a formidable task. Such manual ca1culation when interference eflects are includcd would be impossible to completc in any reasonable time period. However, a medium-sized stored program, digltal conlputer can he used satisfactorily. The method is described in the following sections. THECKETICAL CONSIDEKATIOhS The material balance equation for a reservoir producing by partial or total water drive, as proposed by Van Everdingen, This relationship is linear for Z/a from which thc slopc, Z, and the intercept, N, can be obtained by the least-squares method from the data points. It is not necessary lo know the aquifer properties to uktain oplimum values tor 2nd IV. Various assumptions are made tor At,,: where 11 is production time, seconds (oilfield between the equal successive time intervals into which the history is divided. t,, h It, times the number of equal time periods from i.e.. the total dimen-sionless time interval from It is noted that the dinlensionless time interval, At,,, involves all the relevant aquifer properties. Accordingly, any assunlption of is an assumption of the combined aquifer properties which pertain to the solution of the equation. Deviations of the data points from a straight line arc calculated for each assumption of and the value of A, correspond ing to the minimunl deviation is chosen as the optimum solution. This method is described in Ref. 1 and 2. Thc material balance solution is usually made with an initial assumption that the reservoir being studied is located in an infinite aquifer from which there are no other withdrawals. Deviation of the points by amounts greater than can be attributed to inaccuracies in field data may be the result of: (1) boundary effects of a limited aquifer, (2) pressure interference from othcr pools completed in the .sarne aquifer, and (3) a combination of these effects. Differentiation of these effects can be made only on the basis of geologic data. Pressure interference from other fields will result in a pressure drop at the original oil-water boundary having an interference component, The measured instantaneous pressure drops at the oil-water

By P. D. White, J. T. Moss, J. S. McNiel

Results of experimental work on the in situ combustion process were first published in this country in 1953' when Kuhn and Koch described results of a three-well test in Jefferson County, Okla. Shortly there-after Grant and Szasz2 described field studies in Nowata County, Okla., in which several modifications of the basic combustion process were investigated by injection of various oxidizing gas mixtures other than air. In the past five years speculation concerning this method of oil recovery has continued, with a number of interesting papers on various aspects of in situ combustion appearing in the literature3,4,5,6,7. However, only one of these' provided actual engineering information on pattern-type field experiments. The primary objectives of the Oklahoma three-well test were to check operation of specially designed electrical ignition equipment and evaluate problems associated with initiation of combustion in a natural oil sand reservoir. Immediately following successful completion of this test in the Pontotoc sand, plans were activated for a second field experiment to be conducted in the same sand a short distance away. The objective of this second field test1 as to establish a relationship between field observations and information derived from laboratory experimentation and computations. Secondary objectives of the test were to develop operating tech- niques and define operating problems, and to obtain information that would assist in the economic and engineering appraisals of the process. Careful planning was required since this test was designed with the hope of providing basic information on the characteristics and operation of a combustion drive. It was necessary to include test facilities which would not only permit precise control and measurement of the process variables but would also provide sufficient flexibility of control to insure that variables in the combustion process could be studied during the course of the test under a wide range of conditions. In order to accomplish these objectives elaborate instrumentation and several control wells were included in the design of the test installation. This type installation was felt to be well suited for an experimental study, but was in no respect intended as a counterpart of a commercial-scale operation. PRELIMINARY LABORATORY WORK An important objective of the field experiment, as stated previously, has been to obtain reliable data on operating variables which might be compared with similar data obtained in laboratory combustion tests. The value of successful correlations between quantities that can be measured in the laboratory and those obtained in a full-scale commercial venture has been well established for other industrial processes. The difficulty of following a process underground should make such correlations even more essential here. Also. approaching the field test phase of development of in situ combustion, it was considered desirable to precede design of test equipment with laboratory combustion studies under a variety of conditions to establish likely ranges of variables. These included temperature, air injection rate, frontal advance rate and produced gas composition.

By J. Douglas, W. T. Ford, G. E. Henderson, I. F. Roebuck

An implicit numerical method is presented for simulating the differential and algebraic relations governing one-dimensional three-phase flow in porous media. The method is based upon compositional representation of the hydrocarbon system. Variable physical properties and water-oil capillary forces are included in the formulation; however, the effect of gravity is ignored. The effects of changing composition and mass transfer are considered through the use of known phase behavior concepts and correlations. The differential and algebraic equations and the numeric approximations to these equations are presented, and the computing algorithm is discussed in detail. This method is used to simulate a single-phase, two hydrocarbon-component gas displacement laboratory experiment. The method is also applied in simulating a solution gas drive and a gas injection problem using a reservoir oil represented as a nine-component mixture. For comparative purposes, the latter two problems also are examined with a one-dimensional volumetric model. The results of the simulation of the laboratory experiment demonstrate the relevance of this method to problems wherein the effects of mass transfer significantly enter the displacement process. The comparison of the results of the volumetric and compositional methods applied to a reservoir system illustrates not only the advantages and benefits derived from examining the hydrocarbon system composition, but also the necessity of this approach in application to a general reservoir problem. INTRODUCTION The advent of large memory, high-speed digital computers enabled reservoir engineers and mathematicians to pool their knowledge in the development of sophisticated techniques for the prediction of oil and gas reservoir performance. These techniques have progressed from volumetric and trend analysis calculations to the development of "mathematical models", or reservoir simulators. These latter models, in general, utilize finite difference approximations to the rather complex partial differential equations that mathematically describe the physics and thermodynamics of fluid flow in porous media. Many forms of this "model" type are available today, and much of the recent literature has been devoted to either improving known methods or developing new techniques for use in these prediction methods. The more advanced techniques in use at this time consist of the solution of differential and algebraic relations that describe a reservoir geometry in one, two or three dimensions and that incorporate reservoir hydrocarbon and water fluid systems that obey specified physical laws, having properties that might easily be measured in the laboratory. This type of model utilizes formation volume factors and other volumetric data, expressed directly as functions of pressure, to represent the reservoir fluid system. Experience gained with this type of simulator, commonly known as a "beta-factor model", has indicated that the approach has many outstanding defects, most of them due to the assumption that those properties measured in the laboratory completely describe the behavior of the fluid system throughout the life of the project under study. The effects of varying hydrocarbon composition and mass transfer between the phases of this hydrocarbon system must, by definition, be ignored. These defects, which may often be ignored in

Jan 1, 1970

By K. E. Merklin, F. D. DeVaney

Students of the modern blast furnace seem unanimously agreed that they are observing a major revolution in practice. Rather than changing construction and operation of the furnaces, most of the great advances now under way deal with the raw materials feed. Prepared burdens have gained increasing significance during recent years. Sizing, concentration, and agglomeration have all become bywords to greater production and reduced operating costs. The remarkable results with test furnaces in which self-fluxing sinter makes up part or all of the ore charge foretell even greater improvements. Other investigators have reported many of these advances, and it is enough to predict here that more and more operators will turn to the use of self-fluxing sinter. This change in the operator's requirements comes at a time when one major section of the iron ore regions, the Mesabi, is finding it difficult to maintain, let alone improve, the tonnage and grade of its shipping product. To meet the new demands with respect to quality and structure, the iron ore producers of this area turned first to screening, crushing, and concentrating intermediate ores. More recently, declining higher-grade reserves have led to multimillion-dollar investments in plants to treat the low-grade magnetic taconites.1,2 To yield a suitable concentrate, the Minnesota magnetic taconites must be ground to about 80 pct through 325 mesh, too fine to be charged directly to the blast furnace or to make acceptable feed to the sinter strand. The pelletizing process was developed to meet the structure requirements laid down by the blast furnace operators. Taconite producers are succeeding in their efforts just when the attention of the blast furnace man is being drawn to the great advantages of self-fluxing sinter.3 The taconite operators are ready with an alternative. Why not produce sclf-flus ing pellets? At the Hibbing laboratory of Pickands Mather & Co., where much of the early work was done that led to Erie Mining's 7.5-million ton taconite plant at Hoyt Lakes, Minn., preliminary investigations have been made. Present Taconite Operations: Details of this work will be clarified by a brief review of agglomeration practice in commercial taconite plants. After the taconite has been ground to about 80 pct through 325 mesh to liberate the magnetite grains, the ore is concentrated on magnetic separators, thickened, and filtered to about 10 pct moisture. This structure and moisture fit in closely with the conditions required to produce good balls. It has been found with taconite concentrates that at least 60 pct of the feed to the balling drum must be —325 mesh to obtain good ball compaction within reasonable time. The filter cake moisture usually permits a slight water addition at the balling drum, and further balling control is obtained by adding about 12 Ib of bentonite and 1 1/2 lb of soda ash per dry short ton of concentrate. These additives, and occasionally small quantities of fine coal, are thoroughly mixed with the filter cake ahead of balling. The swelling property of bentonite improves the green and dry strength of the balls so they can be handled without breakage until they are fired. Soda ash is added for pH control to insure maximum performance of the bentonite, and coal is added for more heat in the firing process when required. The balls, normally 3/8 to l-in. diam, are brought to a temperature of 2350" to 2500°F in the indurating furnace. Heat for this process comes from three sources: 1) fuel burned in the combustion chamber, 2) oxidation of the magnetite concentrates to hematite, and 3) coal added to the balls. Pellet strength is developed by grain growth and bridging and, if enough slag-forming constituents are present, by slag bonding. Conversion to hematite is usually close to 100 pct in the fired pellets. Batch Test Procedures: Initial studies of self-fluxing pellets were made by producing balls on a batch basis under carefully controlled laboratory conditions. The l-in. balls, uniform in size, were fired in an oxidizing atmosphere in a standard laboratory muffle furnace. The firing procedure consisted of

Jan 1, 1961

By H. H. Bein

Most western industrial sands are feldspathic and contain feldspars in variahle amounts. A few deposits will show alumina contents of less than one per cent while others will contain over twelve per cent alumina. Some industries are not especially concerned with the amount of contained feldspar but are interested only in color and in size gradations. Other industries, however, are very much interested in alumina content and set up quite rigid specifications as to this content. Several western plants are beneficiating crude sands both to reduce the iron content and to control the feldspar content. At present, most of these plants are using flotation processes for both controls although a few plants do use magnetic separators for the reduction of iron content. Some work has also been done with electrostatic separators for the feldspar-quartz splits. The Sand Division of Del Monte Properties Company, Pebble Beach, California, has been operating a flotation plant for iron removal and the separation of quartz and feldspar since 1950. As mentioned before, control of alumina, especially in the quartz product, is very important. Some users require an alumina content of less than two per cent and others will demand a product of less than one per cent Al2,O3,. The standard Quinolate method for determining alumina is lengthy and time consuming. The HF —H2SO4 evaporation step is especially critical and, if forced, spattering is apt to occur with a resulting loss of sample. Standard procedure is to evaporate to dry ness overnight at a low temperature. Even with forcing under optimum conditions the procerlnre will take two or three hours to complete. A new method has been developed which allows an alumina determination to be made, in 10 or 15 minutes, on a sample of the quartz product as it is being produced. This pocedure, although simply an approximation, has been most helpful in showing whether or not the product being formed is meeting specifications. This procedure has also allowed a great reduction in samples formerly taken and analysed by the orthodox method. Whether a sample assays 1.75% A12O3, or 1.95% .41,0, is not so important as the fact that it is below the allowable maximum of 2.00%. Similar thinking would apply to products required to contain less than 1.00% A1,0,. The step by step procedures for the method are as follows: 1. Collect sample, drain or filter, and dry. 2. Split sample through standard Jones sample cutter to quarter or eighth sample, depending on size of original sample taken, then split down to about 5 grams through Sepor micro-splitter. 3. Screen through 50 mesh sieve (U.S. Series) and reject undersize. 4. Weigh out 2 grams and place in platinum crucible. 5. Etch with 3-5 mls 38.40% HF for 1 minute at room temp. 6. Decant and wash. 7. Stain for two minutes in same crucible with a 1% water solution of Nigrosene dye. 8. Decant and wash well. 9. Dry.

Jan 1, 1961

ONE DAY IN the mid-1880s, in a suburb 0f Pittsburgh, Pennsylvania, there dismounted from a train the two foremost leaders of the day in the coal and steel industries-Andrew Carnegie and H. C. Frick. Their attention was drawn to a well-loaded car of coke, which their experienced eyes recognized as a superior product. "I'll bet you that coke is from the H. C. Frick Coke Company," Mr. Frick challenged. "I'll bet it was shipped by my company." In a spirit of fun Mr. Carnegie accepted the wager. Mr. Frick lost the bet: the coke had come from M0rewood, one of three sites being operated under the direction of a young entrepreneur, Erskine Ramsay. If Mr. Frick's confidence was somewhat dented by this occurrence, the responsibility was his own. He himself had opened the way for Erskine Ramsay to become the youngest of mine superintendents; and he had dispersed all dissension regarding his choice with the words : "I'm not interested in his years, I'm interested in his record. He makes more coke in an oven than any other superintendent. And I'll take 'em out 0f the cradle if they can make coke... Suppose he is only twenty years old? ... The d --- kid is a genius, I tell you." Erskine Ramsay was to follow in the tradition of Carnegie and Frick. Not only was he ambitious and a worker his background had prepared him for it. Coal mining was in the Ramsay blood. His father, Robert Ramsay, of whom the son once stated that he had no superior as coal mining and mechanical engineer in this country, once accounted in these words for the phenomenal accomplishments which had attached to the name "It does no harm to belong to a family of mining engineers who are just as good as any in America-if it is myself that says it." Anyone acquainted with Robert Ramsay's character realized that he was not given to overstatement. And the above-mentioned Mr. Carnegie encountered young Ramsay again, a few years later in his career, and wrote of him to young Erskine's father, that he was "going to be a credit `tae us a' " (a quotation from Robert Burns.) Nor have Mr. Ramsay's achievements been identified exclusively with the industrial field in which he early asserted himself. He has been an inventor whose techniques in mining engineering have received international recognition. As an investor of foresight, he has benefitted others immeasurably, as well as himself, being an influential factor in the upbuilding of several communities in his chosen and well-loved adopted home state of Alabama since 1887. He is a philanthropist whose benefactions have run into millions, the chief beneficiaries being educational and charitable institutions. Amidst his accomplishments the lighter side of life has not been neglected and he is known for his hospitality, his

Jan 1, 1953

SME-AIME Fall Meeting and Exhibit

Jan 9, 1979

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

Jan 1, 1961

By R. K. Agarwal

In this paper, a new technique developed to analyze two-dimensional nonhomogeneous models is described. A simple three-layered medium with a circular hole centrally located in the intermediate layer is considered. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of the intermediate layer and the hole diameter. A comparison of stress distribution and procedures for preparation and testing of the model are given. The potential of the technique is outlined. In the process of applying the techniques of stress analysis to problems of rock mechanics, the recent discernible trend has been to postulate highly idealized models of physical situations. As new techniques have been developed, more complicated models have been conceived to simulate mote accurately the physical environment to which the analysis results are eventually applied. In this investigation, a new technique is developed to analyze two-dimensional nonhomogeneous models. The technique is used to determine the stress concentration around a circular hole in a soft material overlain and underlain by a hard material. In mining practice, such situations arise commonly in coal deposits and frequently in bedded or vein-type metallic mineral deposits. DEFINITION OF THE PROBLEM A plate, consisting of three layers with a circular hole in the intermediate layer, is loaded uniaxially, Fig. 1. The variable in the experimental investigation is the height of the intermediate layer, H. The diameter of the hole, D, is kept constant. The stress concentration factors around the periphery of the hole, for various values of H/D, are evaluated using the technique of photoelasticity, Table I. TECHNIQUE OF EXPLORATION Photoelastic analyses of composite models have hitherto been limited to the study of lap and butt joints between glued metals and dissimilar materials.1-3 In mining, Haber and Oudenhoven used composite models to study the stress distribution around a circular hole in two-layered media and the behavior of elastic liners in shallow underground openings.4-5 They used the stress freezing technique devised by Dally et a1.6 The procedure used in this investigation is outlined below: Casting of Layer A: Flat sheets of plastic were cast in a silicon-coated mold using Araldite 502 with hardener 951 in the ratio of 100:8 by weight. After

Jan 1, 1969

By G. Thodos, D. E. Matschke

Cansiderable time and effort frequently are expended to establish, with a degree of confidence, the PVT behavior of pure substances. In particular, a great deal of experimental information contributed by a number of investigators is available in the literature. The data of each investigator, although significant in themselves, cannot be used with a high degree of confidence until they are compared with the continuum of information presented by others. Current interest in thermodynamic and transport properties, for not only the gaseous state but the con-densed state as well, requires that PVT infarmation be presented for both regions. The density dependence on temperature and pressure, when presented as a continuum, is of considerable value in itself, especially since the available equations of state fail to properly account for the PVT behavior in the condensed state. For this reason and to incorporate PVT data recently presented in the literature, this investigation was carried out. In their studies concerned with the thermodynamic properties of methane, Matthews and Hurd in 1946 utilized the data of Kvalnes and Gaddy and Olds, Reamer, Sage and Lacey to establish the PVT behavim of methane in the superheated region and the saturated liquid densities of Keyes, Taylor and Smithl in conjunction with the Clapeyron equation to develop the densities for the saturated envelope. Current activity sponsored by API Project No. 44 under the direction of F. D. Rossini has led to a tabular presentation of compressibility factors for gaseous methane in the superheated region.la These values were obtained by using smoothed residuals, developed from experimental data and the Ben edict-Webb-Rubin equation,' to establish internally consistent compressibility factors for the real gas. This approach offers probably the most precise presentation of PVT information for gaseous methane to date. The PVT behavior of methane also can be represented accurately by equations of state such as the Benedict-Webb-Rubin equation or the Martin-Hoa equation.' These equations, although valuable for analytically representing the PVT behavior, lack precision in the compressed-liquid region. The PVT data available in the literature for methane were utilized to obtain reduced densities that are presented in Figs. 1 and 2 as functions of reduced temperature with parameters of reduced pressure. The critical constants utilized for methane are those reported by Kobe and Lynn." These critical values, T, = 191.1°K, PC = 45.8 atm and p, = 0.162 gm/cc, produce a critical compressibility factor, z, = 0.289. The PVT information, as obtained from the literature, in many instances was not presented in an immediately

By A. J. Terrones

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,' by Barrell on Marysville, Mont.,' and by Gold-schmitt on the Oslo district, Norway,' laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf' made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control" in ore finding. Some years later Harrison Schmitt" fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed. Primary exploration and careful sampling of recognized structural targets were instrumental in outlining the copper ore potential at the Antamina and Tintaya districts, thus proving the benefits and reward of careful geological examinations in this type of deposit. The Magistral District: This district lies in the Province of Pallasca, Department of Ancash, in northern Peru, at 8o 16' S and 77" 47' W. High to medium grade copper orebodies in garnetite, bordering a quartz monzonite stock, are exposed at the bottom of a glaciated valley in the western slope of the Andes at 4250 m (14,000 ft)* elevation.

Jan 1, 1959

By Herbert A. Franke

ANY analysis of the aluminum situation, particularly of the factors involved in the current shortage of the metal, must consider the rapid march of events since the Munich fiasco of September 1938. At the end of 1938, the sole domestic producer of aluminum had more than a year's supply of metal on hand, having added 50,500 tons of output to stocks during the year. Not until war had been declared between the United Kingdom and Germany in September 1939 did the United States begin to make serious preparations for defense and a limited national emergency was proclaimed. Congress reflecting popular opinion, was not disposed to spend huge sums for armaments in 1939, and although 31,413 tons of aluminum was withdrawn from stocks. 107,500 tons was still on hand at the end of the year. When the President initiated a 50,000-airplane program in May 1940 the country was astounded, as previous Congressional authorizations of approximately 6000 planes for the Army by July 1911 and 3000 for the Navy by 1914 had been considered adequate.

Jan 1, 1941