Search Documents

By J. G. Baragwanath

CUBA'S lateritic iron ores, occurring on the northern coast of that island, though known to the Spaniards. did not receive any general attention until the close of the Spanish-American War. Preliminary studies of these deposits at that time indicated that the limonite contained small percentages of nickel and chrome, and it ryas subsequently discovered that although the average nickel content was only approximately 0.6 per certain limited areas of ore were suffiniently high in nickel to be considered commercial provided a suitable process fur its recovery could be developed. Early in 1937, Pardners Mines Corp. began a series of investigations which led to the development of such a process. Coincidentally, this company acquired option' on certain properties in the Levisa Bay and Moa Bay regions and conducted a systematic campaign of exploration by test pits and hand-auger holes in the course of which an aggregate of 90.000.000 tons of ore was developed in eight deposits.

Jan 1, 1945

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

By AIME AIME

SECTION DELEGATES were given an opportunity to see how the machinery of Institute administration functions, on Tuesday evening, Feb. 16, when they were the' guests at the regular monthly meeting of the Directors. Of the new board of 25 members, 19 were present at the meeting, including directors from Seattle, Los Angeles, Wyoming, Oklahoma, Chicago and Pitts-burgh, the new junior past-president from Jerome, Ariz., and the new president from .Washington, D. C. The complete list of the 72 in attendance at the dinner,: held in the main dining room of the Engineers' Club, which pre-ceded the general session of the Directors'. meeting, follows:

Jan 1, 1932

By R. D. Satterley

The Sherwood mine is an iron-ore mine owned and operated by the Inland Steel CO. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The Ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about goo ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas go ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. 1). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout as for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft. centers. These main raises are Put up to a height of from 22 to 30 ft. above the level floor, then from the toll of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12½-ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1946

By KENNETH W. GREENAWALT, William Greenawalt

THE patent system, through which an inventor is given exclusive right to his invention for a limited period as a reward for his industry and in reimbursement of his expenditures, originated in England in the famous "Statute of Monopolies," enacted in 1623. The first patent granted in America was to Samuel Winslow, in Massachusetts, in 1641. The basis of the patent system of the United States is a provision in the Constitution giving Congress the power to secure to inventors for a limited time the exclusive use of their discoveries. The first legislative enactment was the law of 1790, which was placed on the statute book after Washington had addressed Congress in its favor. Under this law, the Secretary of State, the Secretary of War, and the Attorney General constituted the board for the examination of patent applications and the granting of patents. The first Secretary of State, Thomas Jefferson, became the first administrator of the patent sys- tem in this country. He personally examined every application filed during his term of office.

Jan 1, 1930

By AIME AIME

AMONG the European nations Germany is the center of interest economically as well as politically, and of prime importance for Europe as a whole is Germany's capacity to produce mineral products for armament and for export in exchange for the import of the essential supplies to maintain its industries. So far as minerals are concerned, Germany is worse off than any other great power except Italy, and deficiencies are being met by attempts to increase output from local deposits and by greater use of substitutes derived from domestic raw materials to replace imported metals, petroleum products, and other minerals.

Jan 1, 1939

By G. Townsend Harley

STOPING methods in which shoveling plays an important part are gradually being replaced by other and cheaper methods. But there will always be considerable shoveling done underground in stopes as well as in drifts, tunnels, urinzes, and shafts. At the mines of the PhelpsDodge Corporation at Tyrone, N. M., the cost of shoveling in all stopes in 1917 amounted to 24c. per T. In the top-slice stopes for the same period, it cost 27 c. per T. or 16 per cent, of the total cost of these stopes. The tonnage for shovelers from all stoping was 9.3 T. per man, and for topslicing 8.2 T. per man. These stopes were not unduly hot, and there was not more than the usual amount of timber to interfere with the work of the men. The tonnages obtained per shoveler were considered low; first, because of a poor grade of Mexican labor, many of the men having come in from railroad grading camps; and second, because of a poor spacing of raises, especially in the top-slice stopes, where, in general, they were spaced 25 ft. by 66 ft. (7.6 by 20.1 m.) centers. The average wage per laborer shift was $2.67 during the year. It was thought, however, that even under these conditions the men were not producing the tonnage that they should, so, with the consent of the management, the writer undertook to determine how the general efficiency of the underground shoveling could be improved. No predetermined plan for conducting these experiments was arranged because we had no definite ideas as to the scope of the work or the number of elements into which the investigation would resolve itself, before all of its phases could be determined. We were sure, however, that any work that would thoroughly cover the ground would have to be in the nature of a systematic time study, combined with a course of instruction in correct shoveling methods and adequate and intelligent supervision of the work. Two or three companies in the Southwest have done some work to determine the proper shovel to be used undcrground, but so far as is known the work has been limited to equipping certain parts of their mines with a particular type and size of shovel and thereafter watching the cost and efficiency records. In each case it seems to have been the shovel that held the 21-lb. (9.5-kg.) load that gave the bcst results. Excepting personal communications from these companies, the only data available on scientific shoveling are contained in F. W. Taylor's book, "The Principles of Scientific Management," and D. J. Haucr's article, in The Contractor for March 29, 1918, "A Hundred Hints for Shovelers." This paper discusses and draws conclusions from several thousand time-study readings, taken both on the surface and in the mines for nearly a year. A sufficient number of readings were taken on each factor in the problem for the plotting of curves of the performances and to obtain accurate indices of the work to be expected from this class of labor. The work is not as complete in all of its details as we would like to havc it, because we were forced to stop the work temporarily, owing to the numbcr of men going into the National service and our inability to get others who could make time studies. The results obtained so far, however, have been of such a startling nature that we have decided to submit them at this time, subject to future modification. It is hoped, also, that a free discussion of this paper will lead to a disclosure of any errors that may have becn embodied and offer some valuable suggestions for the conduct of future work.

Jan 1, 1920

By Morris J. Elsing

FOR MANY YEARS lead and zinc have had the so-called protection of a tariff and it is the purpose of the following brief discussion to show what' such protection actually accomplishes with a view to forecasting the possible results of the present copper tariff. In analyzing the subject, tabulations of the United States production, consumption, imports and exports, including ore and concentrates and all of the metallic products, of both lead and zinc have been made for each year since 1900. Of these data, the relationship of the imports and exports and the relative foreign and domestic prices are shown in Table 1. The conclusions drawn from these figures are listed below. 1. The United States is an exporter of zinc. 2. The United States is an importer of lead. 3. The average price of zinc at St. Louis for the last 32 years has been no higher than on the London market even though zinc and zinc ore have "enjoyed" a protective (?) tariff of varying amounts per pound for 22 years of this period. 4. The average price of lead on the New York market for 32 years has been 1.2c. per pound higher than on the London market, the tariff varying from 0.75 to 1.5c. per pound of lead in ore, and 1 to 2c. or more on manufactured lead.

Jan 1, 1932

By T. B. Brooks

THE iron ores of the Marquette region are mostly extracted in open excavations ; hence the process is more properly quarrying. Several attempts at underground work have been made, which have not, on the whole, been successful. The Edwards mine has been almost entirely wrought by candle-light. The slate ore pit, No. 1, of the New England mine, is now worked in the same way, as is also the Pioneer furnace pit of the Jackson mine. The Champion mine was opened systematically for underground work, with two levels, 60 feet apart, and three shafts at distances apart along the bed. of 200 feet; but this idea has been practically abandoned, the greater part of the ore in that mine being now taken out in open pits. Several other mines have occasionally worked underground stopes, but only temporarily; if such stopes could not be opened out to day-light, they have usually been abandoned. In brief, it may be said that no considerable amount of ore has as yet (1870).been extracted underground in the region, and of that so mined very little has been taken out at a profit; and I may add that it seems to be the belief of the most experienced mining men that this state of things will hold for some time to come for reasons which will appear. Nearly the same remarks may be applied to the mines of the Iron Mountain region, Missouri, the ores of which are very similar in character to those of Marquette. Some of the New York and New Jersey magnetic deposits are wrought open, but this is the exception, underground mining there being the rule. The following brief sketch of the geological structure of the Marquette deposits will indicate some advantages of the method of mining employed. The iron-bearing (Huronian) series of rocks, are stratified beds, the principal ore formation being overlaid by a quartzite, and underlaid by a diorite, or greenstone. This ore formation is made up, first, of pure ore ; second, of a mixed ore" (i. e., banded * A second part of this paper was read before the American Society of Civil Engineers. Both papers are embraced in Chapter IX, Part I, Vol. II, Geological Survey of Michigan.

Jan 1, 1873

By AIME AIME

MOTHER example of the broad field that is covered by the mining industry is the recent erection by the Phelps Dodge Corp. of a modern hospital building at Douglas, Ariz., and an identical one at the rejuvenated mining town of Morenci. Managers of even small mining properties are often called upon to build schools, houses, stores, maybe a jail, and provide sanitary arrangements, possibly the while acting as mayor of the town. Those who direct larger properties may have to build hospitals, as in the present instance, construct sewage disposal plants, and sometimes even build and manage railroads. A mining camp achieves its reputation among mining men not entirely by the grade or amount of its ore, or the skill of the operating staff in mining and milling it at a profit-the operation soon acquires a reputation as either a desirable or an undesirable place to live, regardless of its remoteness from what is euphemistically termed civilization. Such a community is indeed fortunate if it can boast of a good hospital.

Jan 1, 1940

By George A. Roche

Investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria used to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of investment strategy for two of the three mutual funds sponsored by the Price organization and for its private clients. However, during the past five years inflation has accelerated due to a variety of factors including the inability of government to meet seemingly unlimited needs with limited revenue sources.

Jan 4, 1972

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By J. A. SINGMASTERN

THE New Jersey Zinc Co.'s vertical retort plants are believed to have been in continuous operation through the whole year. At Palmerton metal purer than that made from the same ore in the old plant has been produced and has been able to compete successfully with very pure electrolytic metal in die castings and other special uses where extreme purity is worth money. A new plant using this process was put in production by the Grasselli Chemical Co. at Meadowbrook, W. Va., early in the summer. It is said to be working very satisfactorily. It is understood that this plant will not produce high-grade metal. Two patents issued to Bunce and Mahler (Nos. 1,749,126 and 1,749,127) describe a method of operating the vertical retort so that practically lead-free metal can be obtained from ores containing consider- able lead. The zinc vapors and other gases leaving the reaction zone are filtered through a column of material maintained at a temperature high enough to prevent much zinc from condensing. The filtering medium is either periodically or continuously changed.

Jan 1, 1931

By John T., Ryan

THE subject assigned me, "Safety in Mining," is a very broad one and only the high spots can be covered in this short paper. As this is a meeting of the Coal Division, these remarks will be directed largely to coal mine safety, although the principles of safety and effective accident prevention methods are relatively the same in every branch of mining or industrial work. The coal mining industry should take pride in the part it has played in the development of the accident prevention movement, and there is ample proof for the statement that the first real organized accident prevention, work, both abroad and in this country, was con- ducted in the coal mining industry.

Jan 1, 1930

By AIME AIME

THOUGH the Annual Meeting of the Institute-officially numbered 158 on the records was delayed a bit at the start by low steam pressure on the locomotives bringing members to New York, the crowd that finally arrived more than lived up to expectations, and the technical program had few difficulties because of absent authors or lack of competent discussers. The transportation difficulties were occasioned by the fact that Monday, Feb. 15, was the third coldest day in the 72 year history of the New York Weather Bureau, the official temperature being 8 below zero. The New York Central's premier train, the 20th Century, due at 9:30 a.m., arrived about 6:30 p.m., and the Commodore, another crack train from Chicago, was about equally late.

Jan 1, 1943

By AIME AIME

AWRDED jointly by the four AW Founder Engineering Societies the John Fritz Medal is generally regarded as the most signal honor that American engineers can confer on a fellow engineer. The roll of 34 recipients contains the names of Lord Kelvin, George Westinghouse, Alexander Graham Bell, Thomas. A. Edison, George W. Goethals, Guglielmo Marconi, and Michael I. Pupin; and among members of the A.I.M.E. now living, Sir Robert A. Hadfield, Herbert Hoover, and Daniel C. Jackling. On the evening of March 1 7 the name of Paul Dyer Merica was formally added to this list of illustrious engineers when the medal was presented to him at a dinner at the Metropolitan Club in New York. The citation read. For important contributions to the development of alloys for industrial uses. Arrangements for the dinner were made by the following committee representing the four Founder Societies: R. C. Allen, George S. Davison, A. A. Potter, and J. B. Whitehead.

Jan 1, 1938

By Dwight M. Lemmon

Encouraged by increased demand and higher prices for such metals as copper, lead, zinc, silver and tin, search was pressed in 1964 for mineral raw materials, especially in parts of the world that are relatively more stable politically and economically. New discoveries of metallic ores continued to be made, discoveries based on extensive geologic and geophysical work but nonetheless made in part because of good fortune.

Jan 2, 1965

By F. P. Dewey

Bone-ash cupels have been used from time immemorial to absorb litharge, and accompanying oxides, in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at resent it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 1, 1918

By W. H. Corbould

The township of Cloncurry is situated in the northwestern part of Queensland, about latitude S. 20" 42' 53" and longitude E. 140" 30' 25". Townsville is the port through which all the trade passes and is about 470 miles east-northeast of Cloncurry township. The Cloncurry copper district covers an area about 200 miles long by 40 miles wide. Unfortunately the mines are very scattered over this area, there being no large groups of mines. Mount Elliott mine is situated about 70 miles south from the township of Cloncurry, and Mount Oxide mine about 150 miles north of Cloncurry. The district has been known for the last 35 years, and in the early stages a large amount of capital was expended with little to show for it; but within the last four years the railway has been extended from Townsville to Mount Elliott and about 40 miles north of Cloncurry, which has made possible the treatment of the ores of the mines on this extension. The Mount Elliott company within the last few years has smelted and converted on its mine 169,688 tons of ore for 20,554 tons of blister copper, containing 20,377 tons of copper, 35,642 oz. of gold and 28,841 oz. of silver, at a cost of about 233 per ton of blister copper, f.o.b. Townsville. This cost included all development, wages, salaries, general management, office, agency, legal expenses, freight, etc. The gold and silver contents would practically pay for freight to Europe, refining, realization charges, etc. The costs of supplies are as follows: Firewood, 15s., coke, 75s., mine timber, 54s., and coal, 60s. per long ton; explosives: dynamite and gelignite, 50s., and blasting gelatine, 65s. 6d. per case, Mount Elliott Mine The pay shoot of the orebody outcrops at the surface for about 200 ft., and lies between two slate walls about 40 ft. apart., having a general

Jan 1, 1915