Search Documents

By A. W. Faheneald, Lewis S. Prater

By taking advantage of the fundamental difference between screening and classification—namely, that specific gravity has no effect on screening but is one of the important factors in classification—a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from % to % in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard 4 2 series. The accompanying flowsheet gives the testing procedure followed.

Jan 1, 1947

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

On the following pages are abstracts of papers published by the Institute during the year 1934 as TECHNICAL PWLICATIONB, CONTRIBUTIONS, m bound volumes and in MINING AND METALLURGY. For abstracts of papers that appear In bound volumes in 1934 but that were published as TECHNICAL PWLICATIONS m 1932 or 1933, see the TRANSACTIONS for 1932 and the YEAR BOOK dated January, 1934. Many of the TECHNICAL PWLICATIONS have been reprinted In bound volumes Information regarding this disposition, and number of pages in each paper, may be found m the list beginning on page 92 Volume numbers are given as listed at the beginning of the index, page 99 The abstracts are grouped as follows:

Jan 1, 1935

By A. B. Young

THERE were produced in this country in 1923 probably in the neighborhood of 12,000 or 13,000 tons of refined and crude arsenic, by far the greater portion coming as a by product of smelting operations. Early this year copper smelters were producing arsenic at the rate of about 425 tons per month and lead smelters at the rate of 7;0 tons per month. During the entire eighteen years prior to 1919, there were produced in the United States only 47,000 tons of arsenic, which amounts to only 25 per cent. of the present output. The great increased demand has come about through the augmented use of arsenates as insecticides and arsenates as weed killers. In an extract from "Mineral Resources of the United States" on "Arsenic in 1922," Messrs. Heikes and Loughlin say, "The minimum possible demand for arsenic in 1923 was estimated at the end of 1922 to be about 13,000 tons, including 2000 tons for plate glass manufacturers, 3000 tons for lead arsenate, 3500 tons for calcium arsenate, 1500 tons for weed killers, 1200 tons for Paris green, 1000 tons for sheep dips and 750 tons for proprietary mixtures. More recent information, however, indicates twice as great a demand for calcium arsenate." The latter has found great use in the last three or four years as a weapon to combat the boll weevil pest of the southern cotton belt. ~t the present writing refined white arsenic is being quoted on the New York market at from 13)d c. to 1455 c. per Ib., while the average price during the eighteen-year period just mentioned was 4.8 c.

Jan 1, 1924

By T. E. Leontis

The importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication, attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne. The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Znt alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-~Zn,f Mg-jZn, Mg-4.4211, Mg-6Zn, and Mg-roZn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. Literature The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison. Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,' Dumas and Rockaert, Haugh-ton and Prytherch,6 and by Spitaler, the last being reported by Beck.' A slight superiority in the tensile strength of chill-cent Mg + 8 es alloy Over the sand-cast alloy was noted by Maybrey.8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1949

By J. B. Newkirk, A. H. Geisler

INTRODUCTION CERTAIN of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some permanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems offer for study over the usual in which an intermetallic compound is formed are many: I. Since the precipitate has the same crystal structure as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be expected to have the same orientation. 3. Small disregistry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from o to 100 pct* thus permitting wide freedom for the study of the effect of composition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1,2 The two have the same [ao] parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for Cu-Ni-Co alloys because of the similarity in constitution but this had not been demonstrated. The present investigation was conducted on a Cu-Ni-Co alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established 4,5 however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system was chosen for a comprehensive investiga-

Jan 1, 1948

By F. W. SUTTER

IN order to have ore available on the completion of the beneficiation plant at Clifton and to provide for continuous production while underground development was carried out, it was decided to develop an open-pit through the crest of a long hill in which the ore outcropped, using 40-ft. vertical benches.

Jan 1, 1943

By Frederick Laist

Introduction IN a leaching process, having obtained the copper in solution, the choice of the precipitation method is influenced y the following factors: 1. Availability of precipitant. 2. Adaptability to the leaching process. 3. Final product desired. 4. Regeneration of leaching solutions. 5. Fouling of solutions. There are three general classes of precipitation methods: 1. The use of iron, scrap or sponge. 2. Electrolytic deposition. 3. The use of some gas or reagent y which the copper is obtained, usually in the form of an intermediate precipitate which requires further treatment. For example, the precipitation of the copper as Cu2Cl2 from chloride solutions, with SO2 gas. The use of iron is adapted to almost any process. It has the great advantage of extreme simplicity, and the recovery of the copper and any values present in a highly concentrated, easily treatable form. The disadvantages are the cost in isolated places, the uncertainty of the scrap-iron market, and the fouling of the leaching solutions. The latter is a serious factor, When a reagent such as salt is used in them, which makes necessary their re-use. Where applicable, electrolytic deposition is very attractive. The copper is obtained in a form directly marketable, there is a regeneration of acid amid no fouling of solutions. Unfortunately, chloride solutions do not lend themselves to electrolysis. An entirely satisfactory anode material has not yet been discovered, although magnetite, apart from being rather brittle, seems to answer the requirements fairly Well.

Jan 7, 1914

By C. E. Brown, D. C. Helms, O. W. Shimer

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By C. H. Gerould

I would like to take a moment to consider our polystyrene-silica replica technique, which was developed at the Dow Chemical Co. and which was mentioned in the paper just given by Mr. Thielsch. He stated that he feared that our replica technique would cause difficulty due to deformation of the metal as a result of the application of pressure during the molding process. We at the Dow have never had any reason to suspect that any deformation of the metal was occurring during the molding process. Our procedure has been to heat the polystyrene to a temperature of 160°C. before applying any pressure, at which temperature the polystyrene is a viscous liquid. By so doing the pressure of the polystyrene against the metal is essentially hydraulic and is therefore applied equally in all directions, which we feel should not cause deformation. Our work using this replica technique has brought forth several indications that deformation of the specimen is negligible. These indications are: I. Direct comparisons have been made between the light and electron microscopes when studying a specific spot on a metal surface. These "same spot" studies were obtained by first taking micrographs at high magnification, with a light microscope, of a specific structure that could be readily recog-

Jan 1, 1947

By J. J. Brown

Wilkes-Barre Meeting, Julie, runs., THE ore-hearth was the earliest type of furnace used in smelting Mississippi Valley lead-ores, which are very pure, and low in silver-content. The first smelters made no attempts to recover lead from the smoke; and since about 15 per cent. of the lead -in the charge escaped in this manner, early practice with the hearth was decidedly wasteful. At most of the large smelting-plants blast-furnaces with auxiliary roasters were substituted for the hearths long ago. But, upon the introduction of the Lewis and Bartlett bag-process for collecting fume, the ore-hearth was used by companies engaged in the manufacture -of pigments, simply on account of the large percentage of fume made by it. In fact, the extraction of lead was kept down by the use of hot blast and other devices. During recent years, however, several smelting companies have realized that the preliminary roasting of galena for the blast-furnace is not economical, and have, therefore, replaced the roasting-furnace with a modification. of the old Scotch hearth, in which a large percentage of the lead in a charge is recovered directly as pig-lead, while the remainder passes partly into fume and partly into slag low enough in sulphur to be charged into the blast-furnace without further treatment. The results obtained have proved so satisfactory, both As to recovery and operating-expense, that one eminent metallurgist has predicted the universal use of the ore-hearth on non-argentiferous ores. The-ore-hearth, thus employed as an adjunct to a blast-furnace plant, is rather a desulphurizer than a smelting-furnace proper,-the chief object being to make a blue slag suitable for the cupola-furnace. Hence, no special care is taken to obtain from it a large lead-extraction. * Head of Department of Ore Dressing and Metallurgy, Oklahoma School of Mines and Metallurgy, Wilburton, Okla.

May 1, 1911

By William Campbell

The structure of iron and steel, though the object of so much study and research for the past 25 years, is by no means thoroughly understood. In the first place, we have three or more distinct iron-carbon thermal diagrams, each with its own supporters, and each representing a theory of the structure and constitution of cast-iron. In the second place, by reason of the fact that austenite, the solid solution of carbon in iron, decomposes in the solid state into ferrite, or pure iron, and cementite (Fe3C), and that quenching from above this transition-range, no matter how rapid, cannot entirely prevent the change and thus preserve the austenite by itself at ordinary temperatures, it happens that under the microscope we find, in addition to the ferrite, Fe3C, and austenite, which the thermal diagram of steel requires, a series of transition-products with distinctive structures, to which have been given the names martensite, troostite, sorbite, etc. Now these transition-products, in addition to the solid solution, austenite, have been the source of much controversy, at times very bitter. One side would insist that, say, troostite was an entity, which the other side would deny, pointing out that it must be a transition-mixture, with a particular structure. That austenite was a solid solution of carbon in iron has been denied by one school; we have been told that Fe24C dissolved both Fe3C and Fe, and thus gave rise to a whole series of quenching-pro-ducts—all this in spite of the fact that no matter how the thermal diagrams differ in regard to cast-iron, they all agree in regard to the solid solution, austenite, for Fe24C finds no place on the diagram. Thus it happens that while the authorities fight both in regard to the iron carbon diagram and the structures met with in hard-

Jan 1, 1913

By C. R. Kuzell

INTRODUCTION KNOWLEDGE of the thermal capacity of gases is of great importance in making metallurgical calculations. The metallurgist is, frequently called upon to investigate and determine furnace efficiencies in which the heat carried into or out of the furnace by gases is a large item in the heat balance. Not only do such problems present themselves in the determination of furnace efficiency, but also in the study of the application of heat is accessory apparatus, such as stoves, regenerators, waste-heat boilers, driers,.etc. The thermal effect of the use of excess air in the combustion of fuel, the theoretical temperatures of combustion, the quantity of heat in hot blast at various temperatures, the effect of hot blast on furnace temperatures, are a few more examples of frequently occurring calorific problems involving gases. So many are the applications of the data on the heat capacity of gases that the subject merits careful study. The heat in a gas maybe due to its heat of combustion, if it is a combustible gas, and to its temperature. The latter is called its sensible heat and is the heat absorbed or evolved by a gas as its temperature is raised or lowered. The heat of combustion of gases is well established and is commonly known. The values can be found in almost any mcdern treatise on metallurgy. The sensible heat of gases has not been so well established because it is in most cases a function of the temperature, and the values of specific heats of gases over a wide range of temperatures have only recently been determined. It is the purpose of this paper to deal with the sensible heat of gases.

Jan 8, 1914

By Max Kraut

UNTIL VERY RECENTLY the flotation process has not found much application in the treatment of gold ores. No appreciable improvement has been made lately in the technology of this application; but the possibilities of flotation have been more fully appreciated. Excellent results were obtained long ago, but few operators paid much attention to them. For instance, in 1915 extensive experiments were carried out by Mr. Beauchamp and Minerals Separation on ores from the Dutch-Sweeney mine near Jimtown, Calif. The ore contained gold-bearing pyrite and laboratory tests indicated a 10c. tailing on a $6 head. In 1918 a 300-ton flotation mill using Minerals Separation machines was built based on the results obtained. However, when the mill began full-scale operation, mill heads did not come up to expectation, being only $4; also the-tonnage was considerably less than had been expected. Flotation mill tailing assayed 15c., indicating a recovery of over 96 per cent, so that excellent metallurgical results were obtained. The operation was a success but the patient died.

Jan 1, 1932

By Oscar Harder

IT is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing -his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treating high-speed steels. Regarding this research, Dr. Sauveur, (22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World&apos;s Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and. related materials in the red-heat range, using various methods. . The results, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as its immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By C. A. Schempp

STUDY of the adaptability of Tintic Standard ores to concentration dates back to somewhat before January, 1921, when the chloridizing mill at Harold, Utah, was put into operation. The operation of this mill has been fully covered in the TRANSACTIONS (Vol. 73). The process consisted essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid; precipitation of silver on sponge copper, and of copper and lead on tin-plate cuttings. This mill was built to treat the low grade siliceous ores having an average content of

Jan 1, 1933

By V. N. Mackiw

IN the process employed by Sherritt Gordon Mines Ltd. for the production of metallic nickel, a sul-fide concentrate is leached with ammonia and air under pressure. Following the removal of iron, copper, and other impurities, there remains a purified solution having the following analysis: 40 to 50 g per liter Ni, 200 to 400 g per liter (NH4)2 SO 4, and 20 to 30 g per liter NH3. Metallic nickel is reduced from this solution by hydrogen under pressure at 300&apos; to 350°F in mechanically agitated autoclaves. A catalyst, ferrous sulfate, is required to initiate the first reduction. After the reduction, the depleted solution is discharged, leaving the metallic nickel in the autoclave. The nickel produced, being in a finely divided form, is used as a catalyst for the reduction of the next batch of solution. Upon repeated use the metallic nickel particles increase in size and become more compact, resulting in the production of a powder with higher apparent density. For this reason, each reduction is termed densification. Finally, when the burden of metal powder in the autoclave becomes too great to obtain effective agitation, both powder and depleted solution are discharged. The autoclave is then filled with fresh solution, ferrous sulfate catalyst added as before, and a new cycle started. The operation is described in earlier publications.1-6 A comprehensive historical review of the reduction of metals from solutions in general was given in a paper by Schaufelberger.7 The experimental data presented in this paper were taken from the work done in the Research Laboratory of Sherritt Gordon Mines Ltd. in Ottawa during the development of the process in 1951 and 1952. The results of the work were tested on a pilot plant scale in Ottawa in the period 1952 to 1953. Following laboratory and the pilot plant studies a commercial process has operated successfully since 1954 in the Nickel Refinery of Sherritt Gordon Mines Ltd. in Fort Saskatchewan, Alberta. General Experimental Technique The experiments were carried out in a stainless steel, 1-gallon, agitated autoclave designed and manufactured by Autoclave Engineers Inc. The inside dimensions of the vessel were 5 in. diam and 12 in. depth. The stirrer consisted of a 1/2 in. diam shaft 11 in. long fitted, with an axial flow type impeller (three blades bent to throw downwards) and a radial flow

Jan 1, 1958

By Robert Maddin

The application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure generallv has been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. Experimental Procedure and Results Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,&apos; were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 120° apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual x and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.³ In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig I shows the initial and final positions of the specimen axes of the crystals. At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to One another&apos; Fig 3-57 photographed On different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1949

By Robert Maddin

THE application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure has generally been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. EXPERIMENTAL PROCEDURE AND RESULTS Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,1 were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 1200 apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual X and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.3 In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig 1 shows the initial and final positions of the specimen axes of the crystals. [ ] At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to one another. Fig 3-5, photographed on different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1948

By E. R. Shorey

FLOTATION-Mill operator&apos;s have recognized that slimes are detri-mental to the flotation concentration of zinc ores. The, presence of primary slime in many of the Wisconsin ores is largely responsible for the failures experienced in treating these ores by flotation. These failures have discouraged the adoption-of the flotation process by opera-tors in the Wisconsin zinc district. The removal of slimes by decantation seemed to be the obvious way to meet the problem of treating slimy or&apos; clayey ores by flotation. To facilitate the removal of slime, it was decided to mix the ore pulp with sodium silicate, which acts to deflocculate the pulp.1 Deflocculation causes slime suspension, making it possible to separate the slime from the sands by decantation.2 Since the literature contains little definite information on the use of sodium silicate to deflocculate ore pulps, a series of tests was conducted to obtain the necessary information. Tests to determine the settling rates of sand and slime in deflocculated pulps were conducted on a dolomite-marcasite-sphalerite ore ground to minus 80 mesh (175 microns) and mixed with water to form a pulp. The deflocculator3 was Mallinckrodt 40° to 42.5° Bé. liquid sodium silicate (Na20 + 3.25Si02). .By microscopic analysis the suspended slimes4 were found to be minus 15 microns (approximately 1000 mesh).

Jan 1, 1934