Search Documents

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is - and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result : Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobusea grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton.

Jan 1, 1935

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After Americzn interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and de- clined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1953

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After American interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and declined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1952

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world's silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After Americzn interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and de- clined in earlier centuries in that a substantial part of its total production was made after 1900. While the district's accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1953

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

US 4,185,872-In the solution mining of uranium values from a subterranean uranium ore deposit, a lixiviant comprising sodium sulfate or other alkali metal sulfate and optionally minor proportions of an alkali metal carbonate or bicarbonate and an alkali metal hypochlorite is introduced into the ore to solubilize uranium therein. The pregnant lixiviant is recovered for processing. E.T. Habib, Jr., assigned to Mobil Oil Corp. Jan. 29, 1980. 5 pp (299-4). Filed- 8-18-78 (934,933).

Jan 1, 1982

By E. P. Sadowski, L. P. Trudeau, C. R. Cupp

The apparent high radiation resistance of two varieties of maraging steel is described and an indication is given of some phenomena that require further study. Two aspects were included in this work: a) effects of neutron irradiation on the room-ternperature tensile properties of 18 Ni (250) maraging steel; b) effects of neutron irradiation on the room-temperature tensile properties and on the impact resistance of 12 pct Ni-5pct Cr-3 pct Mo maraging steel. Subsize tensile and impact test specimens were used. The 18 pct Ni steel was irradiated to a neutron fluence of 3.3 x 10 n per sq cm (>1 mev). The 12-5-3 variety was irradiated to two neutron fluence levels: 1) 1.5 x 10 per sq CTTL (>I mev) 2) 3.1 x 10&apos;9nper sq cm (>1 mev) In all respects both varieties showed unusually high resistance to change in strength and ductility after neutron irradiation. There was no noteuorthy over-aging in fully aged specimens. The aged 18 pct Ni variety showed a 4 pct drop in yield strength upon irradiation with little or no decrease in ductility. The aged 12-5-3 variety showed a 5 pct increase in yield strength on irradiation with a very slight decrease in ductility. The impact transition of the 12-5-3 variety only increased 35 to 45 Co upon irradiation, and the shear energy fracture value for the subsized specimens decreased only half as much as expected frorn experience with conventional steels. THE development of new reactor concepts and nuclear technology now depends to a large extent on the availability of new alloys capable of operating in stringent reactor environments. One of the most important new types of metallurgical material that has been developed in recent years is the maraging steels. This type of alloy is notable for its remarkable retention of toughness at high strength levels. In the course of a research program which incorporated ambient temperature radiation effects studies to determine the mechanisms of strengthening of 18 pct nickel maraging steel,&apos; it became evident that the resistance of the alloy to neutron-induced changes in mechanical properties should be studied. This paper is to present evidence for the apparent high radiation resistance of maraging steel. The experimental program was in two parts: a) Effect of neutron irradiation on the room-temperature tensile properties of 18 Ni (250) maraging steel. b) Effect of neutron irradiation on the room-temperature tensile properties and on the impact resistance of 12 pct Ni-5 pct Cr-3 pct Mo maraging steel, a cobalt-free alloy. EXPERIMENTAL PROCEDURE 18 Ni (250) Maraging Steel. Tensile test specimens were machined to the dimensions shown in Fig. 1 from $-in.-diam hot-rolled bar of the composition shown in Table I. All specimens were austenitized for 1 hr at 1500°F (815°C) in argon and water-quenched. Half of the specimens were then mar aged for 3 hr at 900° F (482°C) in argon. The specimens were irradiated in a fast neutron transformer rod at approximately 120°F (50°C) to a neutron fluence of 3.3 x 10 10 n per sq cm (>1 mev). The irradiation was performed in the NRX reactor of Atomic Energy of Canada, Ltd., at Chalk River, Ontario, Canada. In all cases, the thermal neutron flux was three times as high as the reported (> 1 mev) fluxes. The room-temperature tensile tests were performed with an Instron tensile testing machine operating at a crosshead speed of 0.05 in. per min. The loading frame of the machine, mounted in a hot cell, was remotely controlled. The specimens were tested either

Jan 1, 1968

By Cyril Smith

SEVERAL investigators, mainly concerned with the mechanical proper-ties of the alloys, have studied the so-called aluminum bronzes after various quenching and reheating treatments. Of these works, perhaps the most complete is that of Bouldoires,1 who studied changes of length, electrical conductivity, thermoelectric force, hardness and micro-structure oh tempering quenched alloys containing 5 to 20 per cent of aluminum, although the work of Carpenter and Edwards,2 Curry,3 Greenwood,4 Braesco,5 Matsuda;6,7 Grard8 and others has added much to our knowledge of the changes occurring during tempering. The so-called acicular ß decomposes on tempering at temperatures between 350° C. and the eutectoid, giving rise to a Widmanstätten structure of a needles in a matrix of d or fine a + d, associated with an increase in hardness and almost complete loss of ductility. Matsuda, studied the&apos; eutectoid transformation by means of dilatation and electrical "conductivity measurements during cooling at different rates. He found that on cooling at the rate of 10° C. per minute there was a decrease in electrical resistance and in length instead of the usual increase which occurred with slow rates of cooling. On tempering the rapidly cooled samples, the increase commenced at about 400° C. and at 520° C. the resistance and length had reached the equilibrium values. These peculiarities he accounted for as being due to a transitional phase ß&apos; being formed, ß having an electrical resistance and volume less than either ß or a + d.

Jan 1, 1933

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation&apos;s water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants. IT must always be remembered, with regard to the problem of water-borne industrial wastes, that stream pollution from any cause is just one factor in the comprehensive problem of water supply in modern times. Industries nonexistent 25 years ago are now flourishing, and supplies of water piped to homes and apartments, as well as the greater number of plumbing fixtures per dwelling and per building, have created an ever growing demand on the country&apos;s water resources. Indication of this rapid growth in demand is shown in Table I, which is quoted from Abrams. of Texas increased 287% and the water consumption 7000 per cent." The domestic load varies greatly, depending on the extent of the available supply and the habits of the community. According to the report of the President&apos;s Water Resources Policy Commission&apos; the United States Public Health Service reported a national average of 127 gal per capita per day, varying from 60 gal in communities of 500 persons to 140 or 150 gal in cities of 10,000 or over. Other critical areas may be cited to illustrate the inter-relation between new industrial processes and the demands for water in the area where the new enterprise is located. Powell and Wilson have pointed out that during World War 11, in the vicinity of Louisville, Ky., a rapid expansion of industry took place, consisting of numerous synthetic rubber plants. The demand for water increased from 37 million gal per day in 1937 to 62 million gal in 1943. These heavy requirements drew down the supply stored in the water-bearing aquifers to such an extent that urgent plans for recharging were considered. Similar situations have developed in the Los Angeles area and in the vicinity of Texas City. Warne4 has drawn attention to the situation in Los Angeles area, where in the West Basin the withdrawal of ground water in 1945 was 90,000 acre-ft, almost double the amount of the natural fresh water recharge. The draw down has been so severe that the level of the ground water is now below sea level, and sea water is invading the West Basin aquifers at rates up to 300 ft per year. In the Report of the Engineers Joint Council it is pointed out that in the area of Texas City the ground water table has been critically lowered. In 1930 the daily withdrawal from the water-bearing aquifer was 0.5 million gal. By 1945 the quantity withdrawn

Jan 1, 1954

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By F. L. Kadey

The petrographic microscope is a well known tool in nonmetallic materials research. Its utility in the study of perlite is, therefore, not surprising. Valuable information has been derived on samples smaller than those needed by most other methods of analysis. Relatively little has been written about the petrographic analysis of perlite for two chief reasons: perlite is a material of relatively new commercial interest; and the independent prospector or expander, responsible for most studies, attacks the problem from an immediately practical viewpoint. Hence, petrographic studies of perlite have been limited to academic aspects. Rapid development of commercial interest in perlite has changed the situation. Mining and expanding companies now have effective research tools; and such instruments as the petrographic microscope have added materially to practical knowledge about this mineral. Petrographic techniques employed in the search for suitable deposits screen worthless samples rapidly and inexpensively compared with large-scale expanding tests. Hence, only samples of potential quality are selected for further testing. Field appearance of perlite reveals little about its true identity and practically nothing about its commercial significance. Consequently, any method that can be used to separate the "wheat from the chaff" is valuable. In addition to the conventional thin-section and immersion methods used in evaluation of crude perlite, petrographic microscope techniques have contributed to the study of expanded perlite. When apparently similar materials behave as differently in use as perlites, the internal structure of the individual particles becomes a subject of great interest. The purpose of this paper is to discuss some of the petrographic techniques used to characterize this material. WHAT IS PERLITE AND WHERE IS IT FOUND? Perlite was at first described as a glassy rhyolite possessing a pearl-like luster and exhibiting numerous concentric cracks resembling an onion skin appearance.&apos; Fig. 1 is an illustration of perlite in this classical sense. Recently, its definition has taken on a commercial connotation: an acid volcanic containing 2 to 5% of combined water that, when heated rapidly to the softening point of the glass, coincident with the volatilization of the combined water, expands or "pops". Fig. 2, although hardly fitting the classical description given by Johannsen, is an excellent perlite in the commercial sense. It may occur as a breccia in rhyolite, (Fig. 3) and sometimes it is associated with obsidian nodules, as illustrated in Fig. 4. The term perlite includes the expanded product also. In the United States, perlitic rocks are restricted to the western part of the country. 2 Elsewhere in the northern hemisphere, European occurrences follow a belt beginning in Iceland and extending in a southeasterly direction through Scotland, County Antrim in Northern Ireland, and through the Massif Central of France, Germany, and Hungary; thence, into Italy and Sardinia, and through some of the Aegean Islands. A general oriental belt extends from Japan through Australia and New Zealand. Rhyolitic areas elsewhere in the world undoubtedly contain perlite.

Jan 1, 1963

By Charles Barrett

PLASTIC flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following funda-mental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the lattice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals -"grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by vari-ous investigators for more than 25 years, ? yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of mate-rial that was used in the earlier compression experiments1-hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By B. Ladanyi

The problem of rock behavior under concentrated loadings has been the subject of a number of studies in the past and has been receiving increasing attention by rock mechanics investigators in recent years. Its application covers various fields, but main interest in its solution has arisen in connection with the problems of drilling, bearing capacity, and rock testing. These widely different purposes and fields of interest probably have been one of the reasons why, in spite of the large amount of published experimental data and several theoretical studies, there are still many points which need further clarification. Another reason for this situation undoubtedly is due to the fact that the rock behavior in indentation is complicated by a great number of influencing factors. Experimental evidence shows that, depending on the rock type (mechanical properties, porosity), environment (ambient effective pressure, pore fluid, temperature), and the type of loading (indenter shape, initial embedment, load level, loading rate), the rock response to indentation may vary within very large limits. The widely different rock behavior has made it impossible up to now to treat the problem with a consistent single mathematical theory, but has required instead a series of simplified models covering only certain most important events in the failure sequence. As far as the theory of rock indentation is concerned, this chapter does not add much new information. Its main purpose is, however, to state the indentation problem in a general manner and to indicate which points need to be studied in more detail before its definite solution is attempted. Also, since excellent reviews of the state-of-art of rock indentation in drilling have recently been given,1-4 this will not be repeated here, and only references pertinent to the points of the problem under study will be quoted. The theoretical part of this study attempts to give a quantitative evalu-

Jan 1, 1972

By W. B. Price

AT the New York meeting of the American Institute of Mining-and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."§ The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. PROTUBERANCES ON ADMIRALTY BRASS In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig.. 1a) and upon analysis was found to contain 66.66 percent. copper, 4.02 per cent. tin and .03 . per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and .01 per cent. lead. A sample of the shaggy-rough protuberances at the -very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had -revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation."

Jan 10, 1926

The Colorado Scientific Society, Denver, Colo Charles Henderson, President, 519 U. S Custom House, Denver, Colo. Beginning in 1882, up to. about 1919, the Society published 11 volumes containing many valuable papers From the informa¬tion at hand, the papers in those volumes are now only available in libraries or on file at institutions. Vols 12 and 13 are the current volumes, and the list of the geologic papers contained in them are given here For any information as to price and availa¬bility, address the above. Vol 12 (1929-31) No 1, The geology of the Sangre de Cristo Mountains, by J H Johnson, 2, Relation of the ore deposits of the southern Rocky Mountain region to the Colorado Plateau, by B S Butler; 3, Mosquito Range and the Leadville district, by C H Behre, Jr , 4, Geologic history of the Front Range, by T S Lovering, 6, Revision of geologic structure and stratigraphy in the Ouray district, by W S Burbank, 7, Localization of ore in the schists and gneisses of the Mineral Belt of the Front Range, by T. S. Lovering, 8, Relation of the ore deposits of the southern Rocky Mountain region to the Colorado Plateau, by J. B. Tenney; 9, Preliminary geologic map of the Alma mining district, by Q D. Singewald and B S Butler, 10, The Climax molybdenum deposits of Colorado, by B S Butler and J W. Vanderwilt, 12, Localization of ore bodies at Rico and Red Mountain, by G. F Collins, and Geology of Mount Lincoln and Russia mines, by Q D Singewald and B S. Butler. Vol 13 (1932- ): No. 1, Preliminary geologic notes on Galena Mountain, by J. W Vanderwilt, and High plains of Colorado and New Mexico (Late Tertiary history), by F. M. Van Yuyl and J M. Coke

Jan 1, 1933

By Charles Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metal-lography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method f compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal&apos;s capacity to deform with-out fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orienta-tions resulting from recrystallization and is being extended to other metals and other types of deformation.

Jan 1, 1938

By W. J. Uren, Charles R. Kuzell

The industries engaged in winning minerals from the earth, because of their widespread dissemination, are faced with perhaps as wide a variety of labor-management problems as may be found in any other broad sphere of productive activity. Those problems are continually increasing in volume and complexity, and management has become aware of their growing importance. For the past quarter century at least, labor-management problems have largely been union-management problems. During this period tremendous assistance has been given labor unions through legislation and administrative and political action. In the United States, legislation favorable to unions has come about in the form of the now defunct National Industrial Recovery Act; the Wagner Act, most of which has been carried forward in the Taft-Hartley Act; the Norris-La Guardia Act; the Wage and Hour Law; the Walsh-Healey Act; and others. The result has been to transfer from the hands of management to those who direct the affairs of the unions a large share of control over the industry and to hamper in many ways the remaining control left to management. In the United States there are many examples of the power of unions to injure whole industries seriously with- out regard to the interests of management, the employes, or the public. This chapter deals with the various phases of labor-management relations as they affect the principal segments of the mineral industry in North America. To the greatest extent possible available data is presented pertaining to the unions involved, their relative strengths, labor law, compensation and fringe benefits of employes, working conditions, and related matters. As background, the historical development of union-management relations in the respective segments is included where possible. The section dealing with the United States has been divided into separate

Jan 1, 1959

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input—heat enerb output) used in creating new surface, gliding or slip on atomic planes, twinning, and possibly other lattice rearrangements within the mineral. If it be postulated further that with a hard, brittle crystalline material, such as quartz, the energy used to produce gliding, twinning, and other permanent lattice movements is a very small fraction of the total net energy absorbed, then this energy absorption within the grinding calorimeter can be ascribed to the creation of new surface energy alone. Such energy is, from the thermody-namic standpoint, the true effective work of the grinding device, in this case a tumbling-medium mill. The ratio of this effective work (in calories) to the total energy input (in calories) should express the thermodynamic efficiency of the comminution taking place under the conditions used in the grinding calorimeter. This approach to the measurement of the energetics of tumbling-mill grinding was suggested by some previous work by Fahrenwald and coworkers&apos; with a laboratory ball mill and a thermometer. They measured the efficiency of grinding based on the formula: Pct Grinding Efficiency = Energy (calories) — Thermal Energy x 100 1npZ Output (calories) Energy input (calories) Efficiencies thus measured, while grinding quartz sand, ranged from 19.7 pct to 7.4 pct. Cook in 1915,&apos; used this approach to the problem of grinding efficiencies in stamp batteries and obtained the energy input by stamp weights times drop distances and the energy output by means of thermometers and pulp flow rates. He calculated that 80 pct of the input energy to the stamp shoes was wasted as sensible heat in the ore pulp. No other studies of comminution by this method of energy differences came to the author&apos;s attention. Reasonable agreement as to the order-of-mag-nitude of comminution efficiencies in tumbling-media mills is lacking in the literature. There is a widespread impression among technical workers that the grinding efficiency of the industrial ball mill may be on the order of 1 pct, or even a fraction

Jan 1, 1952

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn&apos; showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.&apos; , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.&apos;

Jan 1, 1956