Search Documents

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By H. Margolin, E. Ence

Two versions of the Ti-Mn binary diagram have been published recently.' , -0th diagrams show two compounds in the region between 40 and 70 wt pct Mn, but disagree as to the reaction in which these compounds are involved. The investigation of the manganese-rich portion of the Ti-Mn binary diagram was undertaken at New York University as part of an investigation of ternary systems with titanium and manganese in order to determine which of the proposed diagrams is correct. A number of alloys between 31 and 70 pct Mn were prepared in a manner similar to that described by Cadoff and Nielsen; except that low currents (110 amp in argon atmosphere) and long melting times (up to 20 min) were used to prepare the alloys. Compositions were determined from weight-loss data, assuming all loss as due to manganese. Heat treatments were carried out with relatively large pieces, since there was a tendency for manganese to be lost during heat treatment. When X-ray diffraction data was to be obtained, the central parts of heat-treated specimens were used to make filings or powders which were not heat treated. Specimens were heat treated from the as-cast state. Heat-treatment times were as follows: 1150°C, 1 day; ll00°C, 2 days; 1000°C, 5 days; and 900°C, 15 days. It should be noted that equilibrium was not attained at 900°, 1000°, and in one case, at 1150°C. Metallographic specimens were electrolytically polished and strain etched by a technique described elsewhere.' At least four, and possibly six, phases were found in the region investigated. On the basis of information available at this time, a completely self-consistent diagram cannot be constructed, and therefore data are presented only for those phases which have been identified by both X-ray and microstruc-ture. Of the compounds detected, the one highest in manganese is the Laves phase, TiMn,, which is hexagonal with a MgZn, type of structure.V he diffraction data for TiMn2 from a 70 pct Mn alloy annealed at 1150°C are shown in Table I. The c/a ratio and parameters of TiMn2 agree well with those of Wall-baum hnd Rostoker et al. The values obtained here are c/a = 1.641, a = 4.825A. Another compound is the y-phase which is estimated to contain about 60 pct Mn. The y-phase has a structure which is identical to that of TiMn, with c/a = 1.639, a = 4.906Å. The fact that y has a Laves-type lattice would suggest that TiMn, has a range of solubility which extends from the composition of TiMn2 (69.6 Mn) to that of y (60 pct Mn). However, this could not account for microstructures which, in the 60 to 70 pct Mn region, show several phases in both the as-cast state and after annealing at 1150°C. Fig. 1 shows a two-phase structure of a 60 pct Mn alloy annealed at 1150°C. The phases present are y (white) and e (dark). If y were TiMn, then, according to Rostoker et al.,' the second phase of Fig. 1 should be P-Ti. The diffraction data for the 60 pct Mn alloy of Fig. 1 are shown in Table I. The starred d-values are from the e-phase and these lines do not correspond to those of &Ti. Comparison of as-cast and 1150°C microstructures of the 60 pct Mn alloy indicates that e precipitated from y. Since y has a

Jan 1, 1955

By W. M. Pierce

CORRUGATED sheet zinc has been used abroad for a great many years as a roofing material. In this country it has been in use for about 10 years. From the outset it was recognized that zinc sheets required closer spacing of the supporting purlins than steel sheets. Exact data regarding safe maximum fiber stresses were not available, however, and on occasions the span used was excessive and the sheets sagged. This paper describes both service and laboratory tests to determine safe maximum fiber-stress values for various grades of zinc for use in calculating the proper purlin spacings for any gage and profile under given loading conditions. These tests consist of laboratory loading tests on full-size roof sections over extended periods of time; of actual roof installations erected in conformity with the indications of the laboratory tests and observed over a period of years; of careful determinations of the apparent elastic limit of several grades of zinc, and finally of static tests1 (so-called creep tests) to determine the rate of flow of zinc under a variety of static tensile stresses at definite temperatures. Certain of the individual tests extended over a period of more than two years.

Jan 1, 1929

By S. J. Hruska, G. M. Pound

The critical supersaturations for appreciable nucleation rate of cadmium crystals on copper and glass substrates at 186°Kwere measured as a junction of thermal-beam energy over a range of source temperatures between 616" and 839OK. There was no effect of source temperature on critical super saturation. This implies that the adsmbate prior to nucleation is in thermal equilibrium with the substrate. THE deposition of metallic vapors on solid substrates has been found to exhibit a critical behavior in that the rate of formation of deposit increases markedly when the intensity of the vapor source is increased slightly.* Evidence of the ability of sub- where Je is the flux which would arrive if the substrate were equilibrated with bulk condensate at the adsorbate temperature. The following work was undertaken to test this hypothesis. A) Energy Exchange Between Metallic Vapor and Substrates. When a freely translating atom collides with a stationary solid body its energy and momentum undergo changes which determine whether the atom is reflected or adsorbed. An atom is considered to be reflected if it returns to a freely translating state after remaining under the influence of the body for only a time comparable to the period of oscillation of atoms on the surface. An atom which remains for a longer time is said to be in an adsorbed state. The parameter which describes the energy transfer occurring at the interface is the thermal-accommodation coefficient which may be defined in terms of energy as Ei = average energy of impingent atoms, Eeq = average energy of an emergent atom which has equilibrated with the substrate, and Eem = average energy of an emergent atom. If a temperature is assigned to each of these energies, we have at as defined by Knudsen.2 Since this allows no distinction between reflected and evaporated atoms, a more specific definition is introduced for the present purposes, namely 71 = probability that an impingent atom is transferred to an adsorbed state, aj = thermal-accommodation coefficient for reflected atoms, and aTc = thermal-accommodation coefficient for adsorbed atoms. During a time t,, the mean stay time, prior to evaporation the adsorbed atom (adatom) will interact with the substrate and this will have the net effect of transferring the adatom towards a state of

Jan 1, 1964

By G. W. R. Kuzyk, John D. Smith

Tantalum Mining Corporation of Canada Limited has been mining tantalum ore from the Bernic Lake pegmatite dyke since 1968. The shallow nature of the dyke and relatively high strengths of the various rock types led to the choice of a room and pillar mining method. Rock mechanic studies have indicated that the original pillar dimensions of 50 feet x 50 feet are conservative for existing rooms. Therefore, a plan to reduce the size of pillars using rock mechanics instrumentation to monitor the resulting stress on pillar remnants and stope backs was devised. The paper describes the test work done on the rock types within the pegmatite dyke. The use of Irad stress cells and extensometers in monitoring the stress in pillars is described. The actual results of the program to date are presented.

Jan 1, 1983

By Y. C. Liu, G. A. Alers, S. S. Choi

In searching for an explanation for the obvious difference between the copper and the brass type of rolling texture, it is common practice to look for correlations with other properties. For example, there are obvious differences between copper and brass in the critical resolved shear stress, the extent of easy glide or stage I, and the amount of "overshooting)) during single-crystal deformation.' Also, the slip lines in copper are fine and wavy while those in brass are more coarse and better described as slip bands.' Since neutron irradiation is known to make these properties in copper change in such a way as to resemble brass,2'3 an excellent test for these possible correlations is to see whether neutron irradiation produces a corresponding change in the texture, i.e., whether irradiated copper develops a brass-type rolling texture. The experiment would also answer the more important question of whether or not lattice defects like those introduced by neutron irradiation have any effect on the development of rolling textures in fcc metals. Experimental studies using conventional X-ray pole figure techniques are inconvenient because the X-ray detection system must be modified to discriminate against the radioactivity which is induced in the specimen by the necessarily long exposure to neutrons. Nevertheless, some texture determinations have been

Jan 1, 1968

By Alan F. Stewart, Douglas R. Piteau, Dennis C. Martin

Three examples of open pits where toppling failure controls the stability and design of the slopes are described. Two examples involve the design of overall slopes in base metal mines. The third example concerns the analysis and design of remedial measures to prevent toppling failure from occurring in a critical slope in a coal mine. The analytical techniques for assessing toppling failure on a rational basis are discussed for the three examples. This includes an assessment of the important parameters which govern the stability for the toppling failure mode. The geological setting and input data for each example are described, as are the important external or limiting factors pertinent to the sites in question. A statistical cumulative technique was used to assess one of the most important input parameters in the two examples involving overall slope design. Both deep-seated toppling failures, involving the entire slope, and shallow bench failures are considered. Results of the stability analyses and their related engineering significance with regard to slope stability and design are discussed. A sensitivity analysis of various parameters is effectively utilized. Design charts are developed and evaluated accordingly. In the example where toppling failure was unavoidable, the rationale for design of stabilization techniques to prevent toppling is discussed.

Jan 1, 1983

By George A. Grandy, D. W. Fuerstenau

Simulation of nonlinear grinding systems is discussed in the context of the size-discretized batch-grinding model. A linear approximation of environment-dependent (or nonlinear) selection functions is postulated for systems which exhibit feed grinding orders less than unity. For this, a convex linear combination of zero and first-order selection function forms is used to obtain an analytical solution that can be used for simulation. An example in which marked nonlinear behavior occurs is rod-mill grinding. Accordingly, a series of grinding experiments was carried out in a batch laboratory rod mill to test these techniques; agreement between experiment and the model was found to be very good. Recently, significant progress has been made in the simulation of linear grinding systems by using a population balance mathematical model. Herbst and Fuer-stenaul presented a parameter estimation scheme that can be used with the size-discretized batch-grinding model, and Gumtz and Fuerstenau3 have extended these techniques to the simulation of locked-cycle grinding. Grandy et aL." summarized the simulation of linear systems and noted important alternate solutions to the batch-grinding equation. Kelsall et a1.'-" discussed the dynamic simulation of linear batch grinding, as well as linear open and closed-circuit grinding. In all of these, the key word is linear, which certainly restricts the engineer trying to simulate a variety of grinding systems. This paper discusses an approach for the simulation of non-linear grinding systems, particularly those which exhibit grinding orders less than unity. Experimentally, dry rod-mill grinding is used to evaluate the technique presented. Batch Grinding Model The size-discretized batch-grinding model has been discussed in detail by Mika et al.'.' and by Herbst and Fuerstenau,' and therefore, will only be briefly developed here. The model is formulated by making a differential mass balance of each size fraction in such a manner that the equation parameters are precisely defined in terms of selection and breakage functions,' which can be either calculated'.' or estimated1 from experimental data. The model is phenomenological because it averages all stress-application events in the system and, therefore, does not distinguish the manner in which individual particles are stressed.' For this average environment, the resistance of all particles in a size fraction to breakage is defined by that size-frac-tion's selection function; and when fracture occurs from an average event, the breakage product size distribution is defined again by that size-fraction's breakage function. The model is deterministic and is derived in terms of a continuous time variable and a discretized size variable,' i.e., the n mass fractions associated with the n defined size intervals (see Table 1 for nomenclature).

Jan 1, 1971

By R. G. Agarwal, Ramey Jr. H. J., Al-Hussainy R.

Although it has long been realized that gas recovery from a water-drive gas reservoir may be poor because of high residual saturations under water drive, it appears that only limited infomlation on the subject has been available until recently. This study was performed to show the qiiantitative potential importance of water influx. Results indicate that gas recovery may be very low in some cases: perhaps as low as 45 per cent of the initial gas in place. Gas recovery under water drive appear to depend in an important was on: (I) the prodirction rate and manner of production; (2) the residual gas saturation; (3) aquifer propertie.); and (4) the volumetric displacement effciency of water invading the gas reservoir. The manner of estimating water-drive gas reservoir recovery can vary considerably. Examples are: the steady-state tnethorl. the Hurst modified steady-state method, and various unsteady-state methods such ac. those of van Ever-dingen-Hurst, Hurst, and Carter-Tracy. The Carter-Tracy water influx expression was used in this study. In certain cases, it appears that gas recovery can be increased significantly by controlling the production rate and manner of production. For this reason, the potential importance of water influx in particular gas reservoirs should he investigated early to permit adequtrtr planning lo optirtize the pay reserves. INTRODUCTION In recent years, the economic importance of natural gas production has become increasingly apparent. This has been evidenced by more intensive exploration efforts aimed at gas production, and exploitation of both deep, as well as low-permeability gas reservoirs. Technical developments such as deep-penetration fracturing have made development of such formations economically feasible. Unfortunately, water influx has forced abandonment of a number of gas reservoirs at extraordinarily high pressures. Although reservoir engineering methods for estimating water influx have long been available, it appears that application of these methods to the water-drive gas reservoir has been sporadic.'a Available methods for estimating water influx which can be applied to the water-drive gas reservoir problem include the steady-state method,1 the Hurst modified steady-state method and various unsteady-state methods such as those of van Everdingen-Hurst. Hurst, and Carter-Tracy. Interesting applications of these solu- tions to gas reservoir and the aquifer gas-storage problems have appeared recently.3,12,14 The experimental study of residual gas saturations under water drive by Geffen et al. in 1952 indicated that residual gas saturations could be extremely high. A value of 35 per cent of pore volume is often used in field practice when specific information is not available. The study of Geffen et al. showed that residual gas saturation might be much higher in some cases. Naar and Henderson concluded that the residual non-wetting phase saturation under imbibition should be about half of the initial non-wetting phase saturation. The Naar and Henderson result that residual gas saturation under water influx should be about half the original gas saturation is recommended as an estimate if laboratory measurements are not available. Thus, it is clear that a considerable portion of the initial gas in place might be trapped in a water-drive gas reservoir as residual gas at high pressure. A full water-drive would result in loss of residual gas trapped at initial reser.voir pressure. Consideration of transient aquifer behavior leads to the conclusion that high-rate production of water-drive gas reservoirs could result in improved gas recovery by reduction of the abandonment pressure. However, there appears to be little quantitative information on this possibility. One of the few advantages of water-drive gas production appears to be improved deliverability through water-drive support of the reservoir pressure. There may also be an advantage in higher condensate recovery caused by pressure maintenance for gas-condensate water-drive reservoirs. In view of the preceding, this study was made to assess the potential importance of water-drive in gas reservoir engineering. The Carter-Tracy approximate water-influx expression was used because this equation offers some advantages in hand-calculation which do not appear to have been generally recognized.' However, calculations were performed in the main with a high-speed digital computer to permit evaluation of the effect of water-drive under a large variety of conditions. CALCULATION METHOD Water-drive gas reservoir performance can be estimated in a manner completely analogous to oil reservoir calculations: a materials balance is written for the reservoir, and a water influx equation is written for the aquifer. Siniltaneous solution provides the cun~ulative water influx and the reservoir pressure. When reservoir performance data (gas produced and reservoir pressures) are available, it is usually possible to match performance data to determine the initial gas in place and the water influx parameters —

Jan 1, 1966

By Gerard Matthes

WITHIN the last three years, aerial mapping has made wonderful progress. Its three sources of development in North America may be enumerated as follows: (1) The work of the U. S. Army Air. Service and Corps of Engineers at the McCook Experimental Field, Dayton, Ohio. This is generally regarded as the backbone of this class of endeavor in the United States. (2) In Canada, a great deal has been accomplished in a practical way by methods that have not even been tried out in the United States. Under the leadership of the late Doctor Deville, the Dominion Land Surveyors have turned out reconnaissance maps of large areas at very, small cost. (3) Private capital has contributed a great deal toward development of aerial mapping in a practical way in the United States. Prominent in this regard stands the Fairchild Aerial Surveys, Inc. which has spent large sums in research and development work, especially in the construction of aerial cameras. Its camera is, at present, the official camera of the U. S. Army and Navy Air Services, also, of the Canadian and Brazilian governments. Aerial photographic surveying is a flexible process and adapted to a variety of uses. To date, it has proved. of direct practical value for engineering projects such as reservoir and power transmission surveys, railroad location, drainage, harbor front studies; also, for many commercial purposes, tax assessment, city planning, forest surveys, and lawsuits. In a few instances, aerial photographs have been used successfully by geologists as base maps on which to record field observations, thereby dispensing with pacing and compass surveys. There is reason to believe that, eventually, the aerial map will find wide application in the work of geologists. The reason for advancing this opinion is that aerial maps have, in other fields, proved more complete as regards detail than maps made by standard processes of surveying and drafting, and often are more accurate than the latter. At the present time, five distinct uses are being made of aerial photographs: There is the "oblique" photograph taken at an angle with the horizon; it is used extensively for illustrations in newspapers, magazines, and advertisements. Also, for reconnaissance purposes, it has been found of great practical value. For illustrating reports of engineers and geologists, it offers many obvious advantages. In the Canadian Surveys, maps have been compiled from oblique photographs.

Jan 3, 1925

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By BARONJUPTNER VON JONSTORFF, Andrew A. Blair, GUNNAR DILLNER

IT is a well-known fact that the results of different analysts, when operating on the same identical sample of steel or iron, are far from concordant, and it not infrequently happens that great annoyance and trouble in the commercial community are occasioned by these discrepancies. Attempts have been made at various times to investigate the causes of such differences and to obtain more reliable methods of analysis. The most important of these was made by the British Association in 1889: The following gentlemen, with Sir W. Roberts-Austen as Chairman, and Professor T. Turner as Secretary, were constituted as a committee to investigate the question, viz.: Sir F. A. Abel, Mr. Edward Riley, Mr. G. J. Snelus, Mr. John Spiller, Professor J. W. Langley, and Professor Tilden. Average .samples of steel were prepared in America under the superintendence of Professor J. W. Langley. The steels, in the form of turnings, were divided and distributed to sub-committees in Great Britain, America, France, Germany, and Sweden. In Sweden Professor Åkerman acted as Secretary to the Swedish committee. The Government Department of Tests was appointed in Germany; Mr. Ferd. Gautier in France; the British Association Committee in England; Messrs. William

Mar 1, 1905

By G. A. Stamboltzis, N. Arbiter, C. C. Harris

Fracture under low-velocity free-fall and double impact and under slow compression have been investigated. The pattern of breakage and the size distribution of resulting fragments of sand-cement and glass spheres have been determined. Photoelasticity methods were used to simulate the stress distributions in free-fall impact in order to explain the observed patterns of breakage. Oblique fracture planes, occurring only in free-fall impact, develop along lines which coincide with the trajectories of maximum compression as determined by mathematical analysis. Breakage efficiencies for different modes of fracture were compared for both types of spheres. For the same specimen and loading system, static loading and low-velocity dynamic loading induce geometrically similar stress fields resulting in reasonably similar fracture patterns and shapes of fragments. This work had its origin in a desire to understand three fundamental processes involved in autogenous comminution: namely; free-fall impact, double impact, and slow compression. To simplify the investigation, it is preferable to reduce the entire multi-stage fracture process to its most elementary form; that is, to study products resulting from a single-stage operation, such as the breakage of a specimen under single fracture conditions. The goal of this research is to study the energy utilization in the single fracture of brittle specimens and to relate the pattern of breakage and the resultant fragment size distribution with the nature of the material, the specimen size, the manner of load application, and the rate of loading. Published works on single fracture have mainly been concerned with tests on large (> 1-in.) irregular mineral pieces, especially coal and coke. These were mainly friability tests employing a single blow on closely sized pieces. More recently, small mineral specimens in the sieve range and glass spheres have been investigated.5-7 Kick8 has reported free-fall and double impact tests with large large cast-iron, cement, and clay spheres. The establishment of a minimum breaking height independent of size in the free-fall impact tests, and the direct proportionality between the minimum work required for fracture and the volume of the specimen in double impact tests were used by Kick as an experimental proof of his classical law of "Proportional Resistances." In the present work, spherical shapes were chosen because of their simple body geometry and consequent impact and stress field symmetry. Because the study involves several physical principles in connection with brittle-fracture, it may be of interest in fields where the strength of materials is of importance. APPARATUS The equipment for the free-fall impact testing is illustrated in Figs. 1 and 2. This consisted of a massive (17 x 17 x 3-in.) hard steel plate onto which specimens were dropped and a specimen release mechanism which could be set at any desired height up to 10 ft above the plate so that the impact velocity could be varied up to about 25 ft per sec. Double impact breakage is characterized by two points of loading situated at opposite poles. For this mode of breakage the apparatus was modified (Figs. 3, 4 and 5) so that a falling mass provided an impact of predetermined magnitude on a specimen resting on the plate. A spring-loaded device operated immediately after fracture to arrest the falling mass and to record its residual kinetic energy. Precautions were taken to avoid secondary breakage. Slow compression tests were performed on a conventional hydraulic testing machine, the specimen being held between two hardened parallel bearing blocks. In the case of glass spheres, carbide bits were used. Photoelasticity studies were performed on two-dimensional models held in a loading frame equipped with a force gauge (Fig. 6). The models were viewed in a polariscope and isochromatic fringe patterns were recorded photographically. SPECIMENS Sand-Cement Spheres: A series of sand-cement spheres were prepared by molding in spherical glass flasks.

Jan 1, 1970

By C. E. Lundin, D. T. Klodt

The binary alloy systems, Y-Ti, Y-Zr, and Y-Hf, have been investigated throughout their entire composition regions. There is no compound formation in any of the systems, and each system is characterized by a single eutectic reaction. The eutectic compositions and temperatures are as follows: A eutectoid reaction pct Y and 870°C occurs in the Y-Ti system, whereas a peritectoid reaction,: pct Y and 880°C occurs in the Y-Zr system. Peri-tectic-type reactions at temperatures above the eutectic levels are postulated for the yttrium and hafnium transfovmations. The development of the technology of yttrium has been given considerable attention during the past few years, and studies of binary phase equilibria have, of course, taken a prominent position in this development. In many respects yttrium, in the third group of metals of the periodic table, is similar to the adjacent group of metals, titanium, zirconium, and hafnium, and the knowledge of the phase relationships of yttrium with these metals is basic to their technology. MATERIALS AND EXPERIMENTAL PROCEDURES Materials. The metals for this investigation were supplied by the General Electric Co., Aircraft Nuclear Propulsion Department. The yttrium was in the form of an arc-melted ingot, and the other metals were in the form of high-purity, iodide-Process crystal bar. Table I lists the purities of these materials. Alloy Preparation. Melting was done by conventional techniques in a nonconsumable electrode arc furnace in an atmosphere of purified argon. Melting conditions for each binary system were the same. Each alloy button was inverted and remelted several times to assure homogeneity. Accurate weights of the charges and resultant alloy buttons were obtained to indicate deviations from intended compositions. No chemical analyses were obtained since melting weight losses were consistently in the range of 0.1 to 0.2 pct of the total weight. 10- or 20-g buttons for each 5.0 wt pct composition increment were melted to survey the three individual alloy systems. Additional alloys differing in composition by 1.0 or 0.1 wt pct increments were also melted to study selected regions of the systems. Metallograpllic Techniques. Standard metallo-graphic techniques were followed for mounting and rough grinding. Preliminary polishing was accomplished using 6-u diamond paste as an abrasive on a Metcloth Lap. Final polishing was done on a Microcloth-covered wheel using 1-u diamond abrasive paste. Purified kerosene was used as a lubricant for both polishing stages. • sothermal- Annealing. Alloys were sectioned for as-cast structlure examinations and then homogenized in preparation for isothermal-annealing treatments. Homo{:enization was accomplished by cold pressing the alloy buttons followed by 72-hr anneals at 1100c. The alloys were encapsulated in Vycor or quartz for the homogenization treatments or for isothermal anneals. Resistance-wound or resistance-element tube furnaces were used for the annealing treatments. The homogenized alloy buttons were cold rolled until cracking occurred or until a -in. specimen thickness was obtained. Small -in. square) specimens for the isothermal anneals were then sawed from the alloys. Each specimen was wrapped in tantalum foil before being sealed in the capsule. Temperatures during the anneals were controlled The time at temperature necessary to equilibrate the structures during the anneals was determined for each alloy system by holding triplicate specimens of alloys at a constant temperature for three different periotls. The specimens were quenched and examined microscopically to determine the number and amounts of phases present in the micro-structure as a function of time. Melting Studies. Eutectic temperatures of the three alloy systems were established from the results of incipient-melting studies conducted on as-cast alloys. Specimens to be melted were suspended on a tungsten wire inside a graphite cylinder placed in a glass vacuum chamber. An optical pyrometer was used to follow the temperature of the specimen as it was inductively heated in a high vacuum. The temperatures were corrected for emissivity losses by standardizing the pyrometer with known-melting-point metals. Accuracy of the temperature measurements is estimated to be + 10°C. The melting point of the yttrium was determined to be 1550°C by this technique. The invariant-temperature levels were also checked by an anneal-quench technique. This technique consists of annealing a series of

Jan 1, 1962

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By T. C. Boberg, R. B. Lantz

This paper presents a method for calculating the producing rate of a well as a function of time following steam stimulation. The calculations have proved valuable in both selecting wells for stimulation and in determining optimum treatment sizes. The heat transfer model accounts for cooling of the oil sand by both vertical and radial conduction. Heat losses for any number of productive sands separated by unproductive rock are calculated for the injection. shut-in and production phases of the cycle. The oil rate increase caused by viscosity reduction due to heating is calculated by steady-state radial flow equations. The response of successive cycles of steam injection can also be calculated with this method. Excellent agreement is shown between calculated and actual field results. Also included are the results of several reservoir and process variable studies. The method is best suited for wells producing from a multiplicity of thin sands where the bulk of the stimulated production comes from the unheated reservoir. The flow equations used neglect gravity drainage and saturation changes within the heated region. INTRODUCTION This paper presents a calculation method which can be used to predict the field performance of the cyclic steam stimulation process. The calculation method enables the engineer to select reservoirs that have favorable characteristics for steam stimulation and permits him to determine how much steam must be injected to achieve favorable stimulation. While the calculation represents a considerable simplification of physical reality and the results are subject to numerous assumptions which must be made about the reservoir, it has been found that realistic calculations can be made of individual well performance following steam injection. The duration of the stimulation effect will depend primarily on the rate at which the heated oil sand cools which, in turn, is determined by the rate at which energy is removed from the formation with the produced fluids and conducted from the heated oil sand to unproductive rock. A complete mathematical solution to this problem is a formidable task, and finite difference techniques would undoubtedly have to be used. The calculation method pre- sented here utilizes analytic solutions of simple related heat transfer and fluid flow problems. The method is sufficiently simplified that it can be used as a hand calculation, although the calculations are somewhat lengthy and laborious. For that reason, the analysis was programmed for an IBM 7044 digital computer. Well responses observed at the Quiriquire field in eastern Venezuela&apos; have been matched using this program after making suitable approximations for reservoir and wellbore conditions. One of the most valuable uses of this calculation method is to assess the effect of reservoir and proc-cess variables on the stimulation response. This paper contains results of several studies made of key reservoir and process parameters. Among the most important of these is the influence of prior wellbore permeability damage. If a well is severely damaged prior to stimulation, a higher stimulation response will be observed than if it is undamaged. If a portion of this damage is removed, a permanent rate improvement will occur. THEORY I)ES(:KJJ&apos;TION OF CALCULATION METHOD The process of cyclic steam stimulation is essentially one of reducing oil viscosity around the wellbore by heating for a limited distance out into the formation through the injection of steam. Suitable modifications of the calculation technique presented here can be made so that stimulation of wells by hot gas injection or in situ combustion can also be calculated. A schematic drawing of the heat transfer and fluid flow considerations included in the calculation method is shown in Fig. 1. In brief, the calculation assumes that the oil sand is uniformly and radially invaded by injected steam. For wells producing from several sands, each sand is assumed to be invaded to the same distance radially. In calculating the radius heated rn energy losses from the wellbore and conduction to impermeable rock adjacent to the producing sands are taken into account. After steam injection is stopped, heat conduction continues and oil sands with r < ra cool as previously unheated shale and oil sand at r > r, begin to warm. The effect of warming of oil sand out beyond r, has little effect on the oil production rate compared to the effect of cooling of the oil sand nearer the wellbore than ra. Thus, in computing the oil production rate, an idealized step function temperature distribution in the reservoir is assumed where the original temperature exists for r > rn and where an average elevated temperature exists for r < rn. The average temperature in the oil sand for the region r < rn is computed as a function of

Jan 1, 1967

By K. H. Coats

This paper describes an approximate technique for handling the problem of percolation of evolved gas upwards through the oil column in computer simulation of natural depletion. This technique has been incorporated into a general model for simulating three-phase flow in one, two or three dimensions. The mathematical model for perfonning these calculations is described in detail in a separate article. 1 While vertical gas percolation occurs during natural depletion in a reservoir of any configuration, it is especially pronounced in the pinnacle reel or bioherm. The reel may have an areal extent less than one section with a thickness of up to 800 It. The upward percolation of evolved gas often limits the time step in calculations as little as one day. Using this small time step, computer expense for a single 30- to 40-year simulation on even a one-dimensional basis has exceeded 92,000. The method described here for handling the percolation allows time steps of 60 days or more (depending on reservoir size and production rate), resulting in a considerable reduction in computing expense. The method also allows calculations in which secondary gas caps build up in tight zones of the oil column below the main gas cap. The validity of the method is indicated in connection with an example pinnacle reef field. Calculated results using a 2-day time step (where the method in question is not needed and not invoked) are compared with results using the method and a 60-day time step. The comparison shows good agreement. Results from one- and two-dimensional simulations of the reef are presented along with the corresponding computing times on the CDC 6600 computer. A three-dimensional simulation was also performed and the required computing time is given. INTRODUCTION A general analysis for simulating three-dimensional, three-phase flow in reservoirs has been developed. 1 In applying this model to reservoirs undergoing natural depletion, a time-step restriction was encountered due to the flow of evolved gas upwards through the oil column and toward the gas cap. A remedy for this problem has been incorporated in the analysis and is described here. The time-step restriction is encountered only in calculations which include flow in the vertical or near vertical direction. The restriction occurs to some extent in reservoirs of any geometrical configuration, but it is especially pronounced in the pinnacle reef or bioherm where the ratio of thickness to areal extent is unusually large. This paper describes the problem, a method of handling it, incorporation of the method in the three-dimensional, three-phase model, and, finally, a test of the method&apos;s validity in an application to an example pinnacle reef reservoir. THE PROBLEM During the early stages of reservoir depletion, pressure falls below bubble point in progressively lower regions of the oil column. Continuing production results in evolution of dissoived gas throughout the oil column. This gas then percolates upwards toward the top of the reservoir. If the gas encounters a sufficiently low permeability zone in its travel upward, then it can accumulate and form a secondary gas cap. If no zones are encountered which are tight enough to hold gas against the gravity forces, then the gas travels on until it reaches the top of the sand or the main gas cap. Numerical simulation of multiphase flow in reservoirs is generally performed with time steps such that the flow of a fluid into or out of a block in one time step is a fraction (considerably less than one) of the total amount of that fluid present in the block. Use of a time step where the time step&apos;s

Jan 1, 1969