Search Documents

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

November 21st, 1871. THE first session of this meeting was held Tuesday evening, in the chamber of the Common Council, the President, Mr. David Thomas, in the chair. Mayor Carroll, of Troy, gave a cordial welcome to the Institute, which was responded to, on behalf of the Institute, by the first Vice-President, Mr. R. W. Raymond. The Council reported the names proposed for membership with recommendation for election. The following named gentlemen were duly elected Anthony, J., - Williamstown, Pa. Babcock, George, - Troy, N. Y. Blake, Theo. A., - San Francisco, Cal. Blossom, T. M., - New York. Boalt, James A., - San Francisco, Cal. Bowman, Amos, - San Francisco, Cal. Chester, Prof. A. H., - Clinton, N. Y. Dewey, C., - Pittsfield, Mass. Dock, Gilliard, - Shamokin, Pa. Emerson, G. D., - New York. Endres, John J., - Pittsburgh, Pa. Firmstone, Frank, - Easton, Pa. Fowle, W. B., - Philadelphia, Pa. Frazier, Prof. B. W., - Bethlehem, Pa. Gardner, George A., - New York. Goodyear, Watson A., - San Francisco, Cal. Griswold, Chester, - Troy, N. Y. Griswold, J. A.,* - Troy, N. Y. Hague, J. D., - San Francisco, Cal. Hahn, O. H., - Eureka, Nev. Harkness, T. C., - Wilkes-Barre, Pa. Harris, Samuel, - Hudson, N. Y. Henry, E. T., - Oxford, N. J. Holley, A. L., - Brooklyn, N. Y. Howe, H. W., - Troy, N. Y. Hunt, Dr. T. Sterry, - Boston, Mass. Jannet, J., - Troy, N. Y. Knapp, John A., - New York. Laughlin, Henry A., - Pittsburgh, Pa. * Since deceased.

Jan 1, 1873

By Gerhard Derge

METALLURGISTS have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steelmaking of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxidizer in rimming steels.1 Likewise, the effectiveness of boron as an alloying agent has been demonstrated, 2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron, Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B203 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. EXPERIMENTAL PROCEDURE No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The most satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron 5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period of time. However, by using the rotating

Jan 1, 1946

By H. L. Brunjes, G. B. Gould

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By G. B. Gould, H. L. Brunjes

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Cleland N. Conwell

Intermittent coal mining has been conducted in Alaska for over a century. The first report of coal in Alaska was by the Veechy expedition of 1826 and 1827. Whaling ships used coal from Corwin Bluff near Cape Beaufort during the early and latter parts of the 19th century. The first coal mine in Alaska-and probably the oldest in the Pacific coast of North America-was opened by the Russians at Port Graham on the southwest tip of the Kenai Peninsula. The mine was operated from 1855 until 1867 when the United States took possession of Alaska. From 1880 to 1915 coal mining was carried on intermittently at several localities including Unga Island, Herendeen Bay, Chignik Bay, Kachemak Bay, and several points along the Yukon River. Small coal mines along the Yukon River provided fuel for the river steamers traveling from St. Michaels to Whitehorse. The area of sustained coal production began with the completion of the Alaskan Railroad from Anchorage to the Matanuska coal field in 1916 and to the Nenana field in 1918. Coal production continued to increase until 1953, at which time the oil and gas fields in Cook Inlet were developed. Oil and gas eventually replaced the Matanuska coal as a means of providing heat and power. The military in the Anchorage area shifted from coal to oil in 1967 causing a decrease in production. The increased demand for electric power in the Fairbanks area offset the decline and coal production started to increase. In 1969-1970 the Golden Valley Electric Assn. (GVEA) constructed a mine-mouth power plant 70 miles southwest of Fairbanks near Healy and a power line to Fairbanks. Location of Coals in Alaska Coals are found in all geographical subdivisions of Alaska. Coal in Alaska ranges in age from Carboniferous to Tertiary, and grade from lignite through anthracite. Fig. 1 shows the locations of Alaskan coal fields. The only fields that have been developed extensively are the Matanuska and Nenana. Fig. 2 illustrates the annual production of coal in Alaska and the ratio of underground to strip mining.

Jan 1, 1973

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962

By J. A. Solomon, H. E. Shafer

As a result of the great demand for metallic aluminum and the scarcity of domestic bauxite, numerous processes have been proposed and developed to extract the oxide of this metal (Al2o3) from clays, shales, and other low-grade raw materials.1-4 An exploratory study was made to extract alumina with sulfuric acid from relatively impure coal-associated draw-slate and to establish an optimum calcination temperature for maximum recovery. Draw-slate is the term used to describe the hard, slaty material directly overlying many coal seams and may range from a few inches to a few feet in thickness. Alumina content of these draw-slates may range from as low as 15% to over 35%. Although the following results are limited in scope, some of the data should prove beneficial for further work. Coal-associated clay, shale, and gob heretofore have been considered nuisance products; any successful alumina extraction process would greatly enhance the worth of these almost limitless resources. This research demonstrated that an optimum calcination temperature for alumina extraction could be established for a coal-associated draw-slate and that this temperature was lower than those suggested in previous work with unspecified clay types. It should be noted that slightly higher acid concentrations and somewhat finer particle sizes were used in this series of tests as compared to previous work. EXPERIMENTAL WORK Essentially, alumina extraction proceeded in four steps: 1) grinding, 2) calcining, 3) acid leaching, and 4) precipitating of aluminum sulfate. An initial series of reference tests to determine the optimum temperature of solubility for alumina was run using relatively pure kaolin. Kaolin forming clays are hydrous aluminum silicates of the approximate composition 2H2O A12O3 2SiO and kaolinite is the mineral that predominates in most kaolins. 5 The kaolin was ground to -30 mesh and subsequently calcined at temperatures ranging from 100°C to 700°C. Each sample was calcined for 1 hr in a muffle furnace and in turn subjected to sulfuric-acid leaching (H2SO4, 9 molar) for a 2-hr period. The filtrates were analyzed for the amount of dissolved alumina recovered.637 Also, each sample of leached or barren residue was

Jan 1, 1968

By B. R. Hollebone

The chemical action of molten anhydrous pyridinium chloride (pyridine hydrochloride) on oxy salts and ores of some Group IV and V metals are discussed-in particular zirconium, hafnium, niobium (columbium) , and tantalum. Laboratory-scale experiments are described whose results suggest that this reaction might provide a practicable means of converting ores of these metals to the anhydrous metal chlorides. Experimental results are given which provide some insight into the nature of the reactions and some of the compounds which could be present at intermediate stages. The treatment of ores of the more refractory metals is difficult and expensive and often demands the use of gaseous chlorine, hydrogen fluoride, or other reagents which are, if nothing else, expensive and dangerous to use. This situation is, of course, due to the strong metal-oxygen affinity resulting from the high charge and the small size of the metal ion which combine to produce such high lattice energy in the metal oxide as to defeat standard reduction methods. Thus, the characteristic of these metals which leads to one of their most important properties—corrosion resistance—is the main hurdle in obtaining the metal. Many common methods' for treating ores of zirconium and niobium (columbium), for example, proceed as directly as possible to the preparation of anhydrous halides. These halides are purified by now standard processes of solvent extraction, fractional distillation, and so on. This paper reports on preliminary stages in the development of a method of treating these ores—particularly of niobium—so as to prepare the anhydrous, volatile halides by the use of chemical reagents which are much more easily handled than those used at present. CHEMICAL PRINCIPLES The solvent action of aminium halides has been referred to periodically in the literature over several decades. The chemistry of pyridinium chloride has been discussed particularly by Audreith2 and Starke.3 However, since this is not familiar chemistry in its nonaqueous setting, it is perhaps well to point out some general metallurgical principles and applications. One can use, as point of departure, the fact that HC1 dissolved in pyridine is an acid very much the same as aqueous HC1. It thus gives essentially all the reactions of the HC1 with which we are familiar. However, when the ratio of HC1:pyridine reaches 1:l (a ratio far higher than is possible with H2O) the solution becomes solid C5F5NHC1, pyridinium chloride.* Inter- estingly, the acidic properties of HC1 persist in this medium, although they are manifest only in the molten state of the compound. Some typical reactions of divalent metal compounds which we have carried out in our laboratories are the following: 2PyHCl + Zn — (ZnCl2) + H2 + 2Py 2PyHCl + MnO — (MnCl2) + H2O + 2Py 2PyHCl + CuS — (CuCl2) + H2S + 2Py 2PyHCl + CaCO3 — (CaCl2) + H2O + CO2 + 2Py In these equations, the parentheses indicate a solvated compound which in water would be predominantly a hydra ted cation but which in molten PyHCl will more likely be a complex chloro-anion of the type MC14-. Some important physical properties of pyridinium chloride (PyHCl) are given in Table I. One sees from the data in Table I that at the temperature of molten pyridinium chloride both water and pyridine will boil away. Thus the system will be kept anhydrous. For this reason the reaction 2NbCl5 + 5H2O— Nb2O5 + 10HC1 has no counterpart in molten PyHCl. Instead, the chloride is made even more stable by the formation of a hexachloro complex: Nb2O5 + 12PyHC1 — 2PyHNbC16 + 5H2O + 10Py One interesting property of these complexes is their thermal instability which for the case of niobium can be illustrated as PyHNbCl6 — PyHCl + NbCl5 With a view to possible use of this chemistry in ore treatment, we have attempted to dissolve Pyrochlore (essentially FeO - Nb2O5) and recover the NbC15 from it.

Jan 1, 1968

By R. W. Raymond

In a paper on the Divining-Rod (Transactions, xi., 411), presented at the Boston meting, in February, 1883,I suggested, among other signs of which the skilled prospector might consciously or unconsciously avail himself in the search for springs of water or mineral deposits, the presence of particular grasses or shrubs, and the general appearance of the flora. There are not wanting, in the literature of our art, indications that greater attention was paid to such signs in ancient days than at present. It is the tendency of a scientific age to ignore, or regard as superstitious, what cannot be classified or explained. But the acute though unscientific observation of earlier times often, doubtless, accumulated facts which it would be worth our while to re-examine. It is highly probable that the mining prospectors of the sixteenth and seventeenth centuries, to go no further back, were close students of nature, and knew, though they could not explain, and, for reasons of private gain, would not communicate, many curious and significant facts. We can generalize better than they could; but for that very reason we are, perhaps, their inferiors in observation. They let nothing pass, because all things were equally significant to them. We take wider views, and miss more. And, no doubt, there still exists among practical millers, prospectors,, hunters, Indians, etc., an unwritten.

Jan 1, 1887

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By E. P. Abrahamson, S. L. Lopata

A general relalionship between the amount of glide shear (due to slip) and the macroscopic shape change has been developed. Since the deformation can be large, finite strain analysis is employed. In this treatnzent, the shape change is expressed by a deforlnation gradient matrix, F - [axi/aXj/ where X and x refer lo the initial and final positions of a particle. This matrix is readily evaluated in termas of the amounl of glide shear, a , and the direction cosines of the slip-plane normal and the slip direction for a single active slip systena. In the case of deforma tion from slip on several systems, the product F(a) of the several deformation gradient matrices is first calculated. Then, by assuming that the final configuration is reached by a long series of small shears of magnitude a, occurring more or less alternately in the several slip sys- IN problems of crystal plasticity, it is often necessary to relate the amount of glide in the operating slip systems to the macroscopic strain components. This relationship is relatively simple when only small strains are considered. In this case the separate strain contributions from several slip systems are additive. Such a procedure is incorrect in the case of large plastic deformation. To the authors' knowledge, no general treatment of the latter problem has appeared in the literature. In specific instances, Mark, Polanyi, and schmid3 have derived the relationship between glide and axial elongation during tensile pulling of a single crystal when only one slip system is active. A similar relationship for duplex slip was worked out by v. Göler and Sachs.4 Taylor and Elam1 have also studied in detail problems of large plastic deformation. Due to uncertainties as to the slip systems at the time, ! terns, the final deformation gradient matrix can be obtained. Mathematically, the problem is reduced to finding the limit of F(aN as N — m while a — 0 in such a way that the Product Na = a finite conslant designatzng the accumulated amount of shear. It turns out that this limit is simply eafF1, where F, is the matrix whose elements are the coefficients of a in the F(a) twatrzx. Application is made of the present treatment to a fcc crystal of Permalloy compressed on the (110) plane and contrained to elongate in the [112] directzon. In addition, it is shown that one rnay readily obtain from the general analyszs the well-known formulas relating elongation, amount of glide shear, and amount of lattice rotation for crystals deforming by single and double slip under tension. however, they were mainly concerned with proving that slip occurs on {111}(110) systems in fcc metals. The present general treatment arose out of recent investigations of magnetic anisotropy in cold-worked Fe-Ni alloys6 as well as some related problems in strength anisotropy of single crystals.' Detailed application of the general analysis will be provided in the case of a Permalloy single crystal compressed on the (110) plane and constrained to elongate only in the [112] direction. It will be seen that, as expected, the small strain approximation leads to significant errors after moderate straining. It will also be shown that the present general treatment yields the formulas of Mark et al. and of v. Goler and Sachs in those specific cases. GENERAL CONSIDERATIONS Consider a homogeneous deformation in which a material point initially at moves to (xl,xz,x3), both positions being referred to the same set of Cartesian axes. Such a deformation can be

Jan 1, 1967

By L. C. Graton

Although marked by numerous well-known attributes of its own, gold does not possess a kind and range of physical, chemical and geological characteristics wholly different and apart from those of other metals. Instead, it is merely one of the family of metals, with its individual and distinctive traits subordinate to the underlying family relationships and resemblances. The geologist concerned with pure science will pursue, therefore, the same general course and will examine the same broad kinds of facts and interrelations when studying the occurrence of gold as when studying that of copper or cadmium, or any other metal. But when we come to consider the use and economics of the metals, we discover that gold differs strikingly from all the others. Gold, in short, is unique, not by virtue of its inherent characteristics, but because of a peculiar and concerted psychological regard in which it is held. It will be evident, therefore, that the geologist who would deal with gold supply must give far greater weight to economic considerations than is required in his contacts with any other metal. If the geologist be called the scientist of occurrence, and the economist the scientist of use, the economic geologist stands as the necessary link between them. Perhaps it is in part because the economic geologist has made himself more familiar with the science of occurrence than with the science of use and has thus in some degree failed to bridge effectively the gap between the two fields, especially with regard to gold, that the usen1 of gold now appear to be in a state of general concern and even of alarm for the security and adequacy of future supplies. In the case of no other mineral commodity do the users, as a rule, trouble themselves greatly about the adequacy of supply except in so far as that may affect the price which they shall have to pay for the commodity. Oversupply, with resulting low price, they regard as a gift of good fortune. As to long-term undersupply, they are generally content to go ahead on faith, leaving the producer to discover as best he may the means for meeting their requirements or the inventor to find a substitute. But history has shown that for gold a different situation exists. While

Jan 1, 1931

By J. S. Harris

AS a result of the study of social problems to which so much thought has been given in this country and Europe in the last half century, many employers of labor have come to think that some provision should be made for their workingmen in case of injury. There has been a growing tendency so to administer the laws governing industrial pursuits in these countries as to add self-interest on the part of capitalists, to the plea urged by humanity, that every possible care should be taken to guard the workers from accident; but as no care can guarantee immunity, there is a necessity to supplement these precautions by some method of providing pecuniary aid that shall be available when disabling accidents do occur. It was once a favorite idea of theorists on political economy, that in the ideal state of society every man should take care of himself, and that the less care or control there was assumed by any man over others' private affairs, the better; but this gospel of selfishness has had its day, and it is now generally recognized that in the existing state of affairs the stronger and richer cannot escape the duty of being to some extent, the keepers of their less fortunate brethren ; and, on the other hand, that an assumption of care for them involving to some extent an exercise of authority, is not a thing to he necessarily and always resisted. Out of these convictions, many efforts for the amelioration of the condition of workingmen have grown—which or one result have produced various plans which combine the con-

Jan 1, 1884

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By John D. Verhoeven, Edward E. Hucke

An experimental technique has been developed for the measurement of the rate of electrotransport to a precision of 1 pct in the molten Bi-Sn system. Results are presented across the phase diagram from 30°C above the liquidus to 520°C. A phenomenological description is presented and the data on Bi-Sn are thereby converted to the effective charge, Analysis of the data indicates the true charge of the migrating tin species in bismuth to be +1.8 at 500°C. The data agree well with the recent work of Belashchmko. fieldintensity. The resistivity of the molten Bi-Sn system is also presented. WHEN an electric field is applied to a metal, a relatively large current is produced due to the ease with which electrons move within the metal. The electric field also produces a force on the ions which might cause them to migrate. Such a migration of metallic ions has been detected under certain conditions. This electromigration of the metallic ions will be referred to herein as electrotransport. The study of electrotransport in metallic systems has a rather long history dating back to the initial work of Gerardin1 in 1861. General reviews of electrotransport in liquid and solid metals have been published by Schwarz,2 Jost,3 Seith,4 and Heumann.5 In reviewing the literature it is apparent that the theoretical developments are not yet complete. The difficulty arises in describing the momentum transfer between the migrating ions and the electrons. In addition, there is a lack of good quantitative electrotransport data at high temperatures, especially in liquid metal systems. This work was undertaken to establish quantitative electrotransport data in a liquid metal system which might serve as a critical test of the theoretical developments. The Bi-Sn system was chosen for analysis, and the rate of electrotransport was determined as a function of temperature and composition. THEORETICAL CONSIDERATIONS If all of the atoms of a metal are considered to be positively charged due to the loss of electrons to the

Jan 1, 1963

By G. R. Heckman, H. J. Murphy, C. T. Sims

An incestigation has been made of the effects of heat treatment and alloy composition on the long-time stress-rupture properties and structural stability of the similar nickel-base alloys Udimet-500, Lrdimet-520, and Udimet-700. Rupture test data are presented at stresses ranging from 4 to 50 ksi at temperatures from 1450° to 1900°F for times up to 14,000 hr. Ductility response is emphasized. Optical and electron tnicroscopy were complemented by X-ray diffraction analyses of extracted phases to relate microstructural stability to the observed rupture properties. Particular attention is paid to Udimet-520 since structural characteristics of this alloy appear to vary somewhat from its sister alloys. Both cast and wrought performance of Lrdimet-500 are discussed. The computerized PHACOMP calculational technique, based on electron-vacuncy theory, is discussed and related to structural stability where appropriate. Electron microscopy and microprobe techniques were used to conduct evaluation of the oxidation characteristics of Udimet-500 exposed in air for 16,100 hr. The steady advance in strength and reliability of nickel-base superalloys continues to be one of the high points of modern metallurgy. The stress capability of these materials has increased steadily, allowing higher and higher operating temperatures in the highly sophisticated aircraft and industrial gas turbines now on the market. The attendant increase in efficiency, of course, means greatly improved power output. Gas turbines for industrial and marine use have long been designed with these objectives paramount the usual design requirements in terms of time of service being 100,000 hr. High-efficiency, long-life aircraft such as the supersonic transport require superalloy engine materials with high-strength and long-time structural stability. Thus, materials studied for and operating experience from industrial gas turbines provide a good reservoir from which technology of high value to the SST program can be drawn. This study is one such case. Three prominent nickel-base super alloys—Udimet 500, Udimet 520, and Udimet 700 were extensively evaluated for industrial gas turbine bucket use. Particular attention was directed toward structural stability as a requisite property. Within the present context, structural stability is defined as freedom from the propensity to form strength-robbing or embrittling phases such as u,p,x,or Laves, and the ability to maintain useful rupture strength and ductility throughout design life. MATERIALS The three alloys, cast Udimet 500 (U-500C), Udimet 520, and Udimet 700, were chosen for detailed evaluation based on preliminary studies which indicated that U-500C and U-520 possessed comparable rupture strength capabilities, and that U -700 had a greater strength capability but somewhat poorer ductility than wrought U-500. The nominal compositions of the three alloys, along with the compositions of the heats investigated, are presented in Table I. PROCEDURE Dimensionally rejected U-520 buckets from Special Metals Corp. heat 63370 were heat-treated using the four cycles delineated in Table 11. Cycle A was investigated to determine the effects of a shortened 1700°F primary age. Cycle B was considered a "standard" treatment. Cycle C investigated a higher solution temperature in combination with a shortened primary age, while cycle D assessed the effect of the higher solution temperature alone. These heat treatments were designed to produce optimum combinations of rupture strength and ductility through maximum y' development, the development of a y' grain boundary cushion, promotion of MC carbide degeneration reactions, and agglomeration of resultant M23CB. Since one of the premises of the evaluation of U-520 was that rupture strength would be equivalent to U-500, forged U-500 buckets from Special Metals Corp. heat 62916 were heat-treated with cycles A, B, and C to provide comparison. The heat-treated structures of U-520 and U-500 are illustrated in the 8700 times electron micrographs of Fig. l. The U-700 tested was all from 3-in.-diam hot-rolled and centerless-ground rod from Special Metals Corp. heat 2-1426. Two heat-treatment cycles were employed, E and F of Table 11. Cycle E is a standard four-step, triple-age treatment intended to provide an optimum match of strength and ductility through well-developed matrix and grain boundary y', as recommended by U-700 vendors. Treatment F is a shortened , single-age cycle which could provide a significant processing cost reduction should adequate strength and ductility be maintained. Following heat treatment, rupture specimens of U-500 and U-520 were machined from the buckets and tested. Standard rupture bars of U -700 were machined from the heat-treated rod and rupture-tested. Failed and withdrawn rupture bars were prepared and examined by optical and electron microscopy. Select specimens were electrolytically digested, and the residues analyzed for carbide and topologically close-packed phases using CrKa or CoKo radiation. Of the six different U-500C heats evaluated, five were cast by Misco Precision Casting Co. and one was cast by Haynes Stellite Co. Cast-to-size rupture bars

Jan 1, 1968

By G. A. Moore, D. W. Williams, C. E. Sims

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. 'The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.' Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949