Search Documents

By Lawrence Addicks

ONE of the properties of copper, which has done much to give it its present prominent place among the useful metals, is its electrical conductivity, a property which has now become the chief criterion of 'the value of the commerical product. In pursuance of that distinctively American principle that, 1' the best is none too good," metal of the highest conductivity is usually called for even where such extreme purity is of no advantage, for instance, in the making of brass and other alloys. The average brass-founder feels nervous unless his copper is so very pure that it shows a conductivity of 99 or 100 per cent., while the character of the zinc used is usually overlooked in his anxiety. Electrolytic refining has made it possible to produce copper of a' very high degree of purity, the metallic impurities averaging but a few thousandths of 1 per cent.; oxygen, usually present in the form of cuprous oxide, bringing the total up to about a tenth of 1 per cent. The published data bearing upon the relationship between chemical purity and electrical conductivity is, however, very scant,' nearly all the work that has been done having dealt with alloys carrying considerable quantities of the foreign elements. In this paper I have brought together the results of experiments extending over a period of several years that have been carried out with the idea of determining the amount of various elements which would lower the conductivity 3 or 4 per cent.-a series of impure coppers rather than alloys. There are many precautions necessary to keep the conditions

Mar 1, 1905

By W. A. Tiller, S. O’Hara

Grain refinement in stirred melts has previously been shown to arise from dendrite segmentation. The present work discusses experiments capable of distinguishing between remelting and mechanical effects which result from fluid motion. Nucleation of still un-dercooled Sn-1 pct Pb melts with a single-crystal seed shows that the grain size of the resulting ingots decreases as the undercooling at nucleation increases up to about 1Z0C, then increases again for larger undercoolings. Pure melts exhibit little refinement as a result of nucleation at any undercooling up to 12°C. The presence of fluid motion gives rise to grain multiplication in pure melts, but the magnitude of this effect is partly obscured by solid-state pain growth. The results indicate that two grain-multiplication pvocesses can operate, one which involves dendrite remelt ing, and another associated with fluid motion. Small ingot experiments indicated that an equiaxed transition can be caused by fluid motion. THE presence of forced convection during recales-cence of undercooled Sn-1.3 pct Pb melts has been shown to give rise to extensive grain refinement during solidification of small ingots of this alloy.''2 In Ref. 2, this refining was shown to result entirely from dendrite fragmentation and not from any nucleation mechanism. The purpose of the present work is to establish what processes lead to dendrite segmentation. Experiments were therefore carried out to determine the resulting structure of both pure tin and Sn-1 pct Pb melts, nucleated at various undercoolings by single-crystal seeds in the absence of forced or natural convection. By comparing the information obtained from these experiments with the results of Refs. 1 and 2, the effects of fluid motion on the ingot structure, and the details of the segmentation mechanisms, should become clear. The results of these experiments should also be helpful in understanding the solidification structures of larger ingots since natural convection, which is known to play an important role in determining ingot structure13 differs only in degree from the fluid-motion effects studied here. I) EXPERIMENTAL PROCEDURE The apparatus shown in Fig. 1 was constructed to permit controlled nucleation of stirred or unstirred supercooled melts using a seed oriented in the tin dendrite growth direction. Because the melts, in all cases, were capable of larger supercoolings than the one used in each experiment, the structure observed always resulted from a single nucleation event at the surface. The sequential procedure was as follows: Tin was melted under purified hydrogen and the oxide removed at a temperature of 450°C . Electromagnetic stirring was then used to clear the surface completely and during this time the guide tube was lowered underneath the melt surface. A pointed Czochralski-like crystal was then propagated from a specially prepared tin dendrite seed4 inside the guide tube while the temperature of the bulk melt was held just above the melting point, ensuring a perfectly clean seed which was epitaxial with the original dendrite. The dendrite and epitaxial seed, still in the guide tube, were withdrawn from the melt which, in turn, was undercooled to 2C° below the temperature at which the nucleation experiment was to be performed. The melt was held there for several minutes, both in stirred and in still-melt experiments. The temperature was next raised to the required value and the melt nucleated by the carrot seed inside the guide tube, the heater power being shut off just after nucleation. In experiments where quenching after nucleation was required, a high-density graphite crucible was used, but otherwise the procedure was as described above. The temperature gradient in the melt before nucleation was kept below 1C° per cm by carrying the experiment out just below the center of the heater shown in Fig. 1.

Jan 1, 1968

By John E. Dorn, Oscar E. Harder

The phenomenon of diffusion, according to the most prevalent conceptions at the present time, undoubtedly played an important part in the formation and distribution of metals and minerals in the earth's crust. Apparently there is good evidence that in the geological rate of cooling diffusion caused numerous materials to separate into individual masses or into duplex structures. As is well known, the early steels were made by cementation; that is, by heating wrought ferrous metal in contact with carburizing materials so as to produce a relatively high carbon content on the surface. If the process was continued long enough, the carbon diffused throughout the piece. A more homogeneous product depended upon further heating and forging, so that the carbon diffused to a fairly uniform concentration throughout the metal. In the modern metallurgical industry, diffusion is the basis for many operations; for example, the production of hard surfaces on steels by carburizing, nitriding, cementing with chromium, silicon, boron and beryllium. Castings or ingots as they solidify do not have homogeneous structures, but these structures are made largely homogeneous by suitable process of heat-treating and the resulting diffusion. It is in modern physical metallurgy, however, that we become greatly concerned about the mechanism of the phenomenon of diffusion. The rates of diffusion, effect of temperature and time on diffusion, and the relation of diffusion to the many properties of the parent metal and the diffusing metal have become important; also, we are concerned with the diffusion of a single metal into a complex alloy. For example, what is the mechanism whereby carbon and nitrogen travel into steel? What is the effect of alloying elements in the ferrous material on the rates of diffusions? What is the effect of simultaneous diffusion of carbon and nitrogen? How does chromium, beryllium, boron, or the like, diffuse into the steel, and what are the effects of alloying elements in the steel previous to the cementation process? These inquiries are by no means limited

Jan 1, 1938

By Oscar E. Harder, John E. Dorn

The phenomenon of diffusion, according to the most prevalent conceptions at the present time, undoubtedly played an important part in the formation and distribution of metals and minerals in the earth's crust. Apparently there is good evidence that in the geological rate of cooling diffusion caused numerous materials to separate into individual masses or into duplex structures. As is well known, the early steels were made by cementation; that is, by heating wrought ferrous metal in contact with carburizing materials so as to produce a relatively high carbon content on the surface. If the process was continued long enough, the carbon diffused throughout the piece. A more homogeneous product depended upon further heating and forging, so that the carbon diffused to a fairly uniform concentration throughout the metal. In the modern metallurgical industry, diffusion is the basis for many operations; for example, the production of hard surfaces on steels by carburizing, nitriding, cementing with chromium, silicon, boron and beryllium. Castings or ingots as they solidify do not have homogeneous structures, but these structures are made largely homogeneous by suitable process of heat-treating and the resulting diffusion. It is in modern physical metallurgy, however, that we become greatly concerned about the mechanism of the phenomenon of diffusion. The rates of diffusion, effect of temperature and time on diffusion, and the relation of diffusion to the many properties of the parent metal and the diffusing metal have become important; also, we are concerned with the diffusion of a single metal into a complex alloy. For example, what is the mechanism whereby carbon and nitrogen travel into steel? What is the effect of alloying elements in the ferrous material on the rates of diffusions? What is the effect of simultaneous diffusion of carbon and nitrogen? How does chromium, beryllium, boron, or the like, diffuse into the steel, and what are the effects of alloying elements in the steel previous to the cementation process? These inquiries are by no means limited

Jan 1, 1938

By Earle E. Schumacher, W. C. Ellis, John F. Eckel

Copper-calcium alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiensl have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1930

By Klaus M. Zeitler

INTRODUCTION One cannot discuss the subject of "Raising Capital in the 1990s" without having a crystal ball and a reliable fortune teller. This discusses "Raising Capital for the 1990sW, which is what Metal1 Mining Corporation did in 1987. We raised (3166 million in an IPO (initial public offering) that was originally planned for only some (375 million. Why did we raise this money? How did we do it, and why was this IPO so successful? The answer to the first question requires a description of the promoter and principal shareholder of Metal1 Mining Corporation, Metallgesellschaft AG. This West Germany company was founded over 100 years ago in Frankfurt as a trading house for non-ferrous metals. It has developed into one of the world's leading firms in the non-ferrous metals industry. The company's worldwide activities in all areas of that business include mining, smelting and refining, the trading of ore, base and precious metals, the production of semi-fabricated and finished metal products, and the provision of engineering, construction and transportation services. Metallgesellschaft AG has also diversified into many other areas, the most significant of which are manufacturing, the production of chemicals, the development and application of technical and chemical processes, the planning and construction of industrial plants, and activities associated with finance, insurance, shipping and freight forwarding, and the provision of barter and countertrade services. The company maintains a network of more than 100 offices around the world; it employs some 25,000 people in its worldwide activities. [Selected financial data, as of September 30, 1987: (MetaUgesellschafl AG) Working Capital DM 8%.6 million CDNS 672.8 million Long Term Debt DM 568.0 million CDNS 426.2 million Sales DM 14.9 billion CDNS 11.2 billion Net Income DM 87.7 million CDN$ 65.8 million Market Capitalization at April 27, 1987: (Metallgesellschafi AG) Outstanding Shares ~,6oo,o0o DM 1,875 million CDNS 1,407 million] For the fiscal year ended September 30, 1987, Metallgesellschaft AG had, on a consolidated basis, net sales of DM13.3 billion, net income of DM100 million and total assets of about DM7.0 billion. Metallgesellschaft AG established the American Metal Company, a predecessor of AMAX Inc. one of the largest ventures undertaken by Metallgesellschaft AG then was the acquisition, through the American Metal Company, of a majority share in the Mexican Penoles mine, a large lead and silver deposit. METALLGESELLSCHAFT AG Figure 1 depicts an overview of Metallgesellschaft AG before and at the time the initial public offering of Metall Mining Corporation's shares took place. It shows that mining was far from the centre of Metallgesellschaft's activities. Therefore, it could not expect to receive an extraordinary amount of board attention. Thus, mining investments not only had to compare well with other mining opportunities, but were in fierce competition with projects from other divisions. In addition, mining was sub-divided into two separate departments -- domestic and international. These two departments had different management styles and diverging interests which resulted in a minimum co-operation between them. The domestic mining department was primarily interested in the survival of the local mines. These mines were characterized by rising operating costs and declining ore grades. It took a special commitment and continued ingenuity to develop and adjust to local conditions, and modern mining and processing technology, in order to remain competitive, or at least survive within the international mining industry. Local management

Jan 1, 1990

By Charles E. W. Bateson

The Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low range of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. Climate and VEgetation. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera ture is generally from 60" to 70" F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100" F. in the day-time, while 115" F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1907

By Clarence S. Ross

INTRODUCTION THIS chapter on the rô1e of physical-chemical processes in ore deposition presents unusual difficulties because it attempts to discuss the theory of processes that are very imperfectly under- stood, but which are among the most fundamental problems now before the student of ore formation. It is generally believed that a great variety of ore deposits are in some way derived from igneous rocks; but we desire to know the mechanism of their splitting off from the parent magma, the physical and chemical character of the material that acts as a medium for transfer from magma to the point of deposition, the manner of deposition, and the methods of replacement and removal of the invaded rocks. This problem is difficult for the field geologist because it concerns forces that for the most part have long since ceased to act. It involves a complex system of which the time for completion extends from the first development of the parent magma through its intrusion, its slow cooling and crystallization, and the final escape of its last residuum, a time probably represented by millions of years. In space the processes extend from profound depths of the abyssal magma which can never be directly observed, through the horizons characterizing deep-seated igneous rocks and ore deposits; those formed at moderate depths; and ends with surficial ones and surface thermal springs. The geologist usually can study the effect at but one of these horizons: he must attempt to fit his puzzle together while seeing but a few parts at a time. Thus he must deal with many isolated phenomena, as if they were the result of many physical and chemical systems; when in fact his problem involves a single exceedingly complex system, and will only be understood when that entire complex system is understood. The geophysicist is handicapped because he must attempt to interpret an extraordinary complex system, involving physical and chemical conditions which he can never hope to duplicate fully, through the study of many exceedingly simple systems.

Jan 1, 1933

By P. Somasundaran, R. D. Kulkarni

Reagentizing at elevated temperature, reported in the past as beneficial for the flotation of hematite using oleate, is studied here as a function of collector concentration, solution pH and ionic strength at various levels of conditioning temperature. The study revealed strong interactions between variables; particularly, the effect of conditioning temperature was found to strongly depend on the ionic strength of the solution. Thus, while an increase of conditioning temperature at lower ionic strengths or that of ionic strength at lower temperatures resulted in an increase of both flotation and grade, an increase of the former at higher ionic strength or that of the latter at higher temperatures caused a significant decrease in both responses. These observations have been explained in terms of the increased chemisorption of oleate at elevated temperatures and the temperature effect of ionic-strength on the salting out of the oleate from the bulk solution. The above effects which were first observed during Hallimond cell flotation tests were subsequently tested with Denver cell using low-grade iron ore. The results obtained using the two test procedures were in agreement with each other. The implications of these effects and interactions for process control of optimum flotation performance must be noted since variation in the levels of the above parameters are likely under plant conditions.

Jan 1, 1978

By B. F. Koch

COPPER reverberatories develop large amounts of exit gases of a temperature in the neighborhood of 2000°F. The gases are not only of a noxious nature but must usually be disposed of at considerable heights above the yard level by a stack. Handling these gases at the temperature mentioned would require rather expensive construction of conveying flues and stack. Moreover, wasting such amounts of heat is certainly most uneconomical. Numerous investigations have indicated that waste heat boilers of the water-tube type are the most practical and economical means for utilizing that heat although the gases are heavily laden with rock dust and copper-bearing slag, which upon cooling form hard deposits on the surfaces of dampers or heat absorbing elements placed in the gas stream. Avoiding Slag and Dust Deposits Based largely on the experience of the paper industry in burning black liquor, a waste heat boiler design was developed a few years ago, providing not only extensive water-wall surfaces for cooling the gases below the fusing point of the slag but also settling out, as far as possible, the solidified particles of slag by creating low gas velocity. Matter carried in a stream of gases or air has a tendency to maintain its original direction upon a change in the direction of the flow of the conveying medium. Reverberatory waste heat boilers installed at Hurley and Morenci endeavored to utilize that tendency for the elimination of slagging particles at predetermined places and before they would strike the tube banks of the boilers. Both installations were successful in minimizing the slagging of boiler tubes and thereby minimizing the need for hand lancing. However, the low draft carried at the up-take of the reverberatory furnaces resulted in a positive pressure in the upper part of the furnace of the waste heat boilers, causing the emission of gases from lancing doors and making more difficult the already unwelcome work of cleaning the boilers by handlancing. Attempting to correct this nuisance as much as possible, the overall height of the Chuquicamata waste heat boilers has been reduced to the minimum considered necessary to obtain proper water circulation in furnace walls. Moreover, it is attempted to solidify slag and dust particles by providing large amounts of water-cooled surfaces before the gas stream reaches super-heater and convection banks of the boilers. The furnaces have been made as deep as an economical and practical arrangement of headers for water

Jan 1, 1952

By John G. Tate, George W. Nicolson, James L. Bruce

FOR more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.1 From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. DESCRIPTION OF ORE BODIES The shape of the ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions, extending from unknown depths below the bottom level at elevation 250 ft below sea level, to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the ore body extended to surface and was mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upperside of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and clay sedimentaries of Miocene and later age. The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-stained by the descending meteoric waters. It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pct Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pct. On the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. Some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. This probably can

Jan 1, 1947

By John S. Alexander

THE spirit of this age encourages the substitution of mechanical for hand labor wherever possible, experience proving that the employer, employer and consumer share alike in the resulting benefits. Through the efforts of the inventor, millions of the laboring class have been raised from being mere contributors of muscular force to be brain workers and directors of those ingenious contrivances now so widely used in the various branches of agriculture, manufacturing, printing, etc. While the genius of invention has accomplished so much in other departments, it seems remarkable that she has not long ere this descended into the coal mine with her wheels, levers, and eccentrics, and provided the toilers there with some device by which their unusually laborious work could be lessened. Until within a very few years, however, little special attention was given to this subject, owing largely, no doubt, to the fact that coal miners as a class were prejudiced against innovations of this kind and ignorantly clung to muscle as the only means of wresting from nature her treasures stored within the coal measures. Thanks, however, to the enterprise and skill of some Scotch and English mine proprietors and inventors, the present decade has seen rapid strides in the right direction, and mechanical coal mining has become a fixed fact in some portions of Great Britain. Making her acknowledgments to the mother country for these earnest and successful efforts, America now comes forward with the Monitor Coal-Cutter as the result of a trial on her part to advance the common cause of economical coal production; for upon cheap fuel the future greatness of both nations largely depends. The object of this paper is to give a few items in regard to this Monitor Coal-Cutter, which, so far as the writer is informed, is the

Jan 1, 1875

By Oliver Smalley

EXCEPT for the work of Guillet, who conducted a systematic investigation on the zinc-replacing value of nickel in brass, and extended his investigation with a view to developing commercial high zinc content nickel brasses, the author does not know of any systematic research on the subject. The most promising commercial alloys and their physical properties obtained by Guillet are given below: Maximum Elonga- Reduction Copper Zinc Nickel Stress, tion, of Area, Brinell Tons Per Per Cent. Per Cent. Sq. In. 55.0 41.0 5.0 24.4 46.5 94 Sand cast. 22.6 27.0 90 Chill cast. 56.7 39.74 3.35 30.0 43.0 51.7 97 Casting annealed 2 hr. at 750° C. 33.9 33.0 50.7 144 Cold-drawn bar. 55.15 42.3 2.24 29.8 33.0 116 Casting annealed 2 hr. at 750° C. 32.3 29.0 151 Cold-drawn bar. These test results scarcely justify the use of such quantities of so expensive a metal, and could have been obtained from ordinary commercial brass. For purposes of comparison, the physical properties of ordinary brasses, ranging from 70 per cent. to 50.1 per cent. Cu in both the cast and normalized1 conditions are included in Table 1. These incidentally furnish a useful standard of the properties of castings and of rolled, extruded and forged brass when correctly annealed. A close study of some of the well-known special brasses containing nickel reveals a series of alloys which bewilder by their complexity, and one can only hazard a guess at the function and commercial value of each of the many elements used.

Jan 10, 1925

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate of oxidation of ferrous iron to ferric iron in pure molten iron oxide by carbon dioxide + carbon moloxide mixtures at 1550°C. It is shown that the rate-controlling process is the interdiffusion of iron and oxygen atoms within the melt. The inter-diffusivity of iron and oxygen in the melt is obtained from the results and the value of (5.0 * 1.0) x 10-5sq cm per sec is recommended for the temperature of 1550°C. Similarly, it is also found that the rate of reduction of molten iron oxide is con -trolled by diffusion in the melt; however, apparent interdiffusivity values from these experiments are 10 to 20 pct higher than those obtained in the oxidation experiments, by virtue of convection arising from density difference. The results of the oxidation experintents are used to calculate an estimated self-diffusivity of iron in molten iron oxide of (1.5 * 0.5) x sq cm per sec. BECAUSE of the industrial importance of iron oxides, the study of the kinetics of both the reduction and oxidation of the solid oxides has received a great deal of attention. However, knowledge of the kinetics of similar reactions in the liquid state is very meager. Dancy 1 studied the kinetics of reduction of molten iron oxide by carbon in pig iron and found that the reaction is very fast. It was concluded from the results that the reduction of molten ferrous oxide is a first-order reaction up to 80 pct reduction, while

Jan 1, 1964

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

By L. Adler

A relatively simple and effective technique is proposed to deal with the failure of geologic masses containing weakness planes. This technique, termed irextended" rupture envelope, provides a means to clearly distinguish rock and soil from fractured rock and, on a theoretical level, considers a matrix-inclusion system. It may also constitute the link between Mohr's and Griffith's failure theories. Included in the article are five sample problems concerning site location, structural design, strengthening the plane of weakness, changing the magnitudes of major and minor principal stresses and changing the orientations of major and minor principal stresses. Engineers trying to solve design problems in rock and soil mechanics have often assumed an iso-tropic and homogeneous medium. For naturally occurring geologic masses this assumption has always been viewed with regret. The following analysis which deals with the effects of plane anisotropy on failure presents a solution to this. The planes of weakness are joints, faults, bedding planes, fracture and cleavage (natural and induced), foliation and schistosity. The physical properties of these weakness planes include an undulating surface, frictional resistance, discontinuous extent, filling material, tightness and presence of water to cause a hydrostatic pore pressure. All of these properties relating to failure can be summarized in Mohr's rupture envelope for the plane of weakness. This, along with the geometrical orientation, strike and dip, of the plane of weakness produces what is termed an irextended" rupture envelope. MOHR'S STRESS CIRCLE AND RUPTURE ENVELOPE The significant features of these concepts are listed below.' 1) A point on the u - r coordinate plane represents the normal and tangential stress components on a reference area in the material. This area can have any orientation. (Fig. la)

Jan 1, 1963

By Harmon F. Fisher

In the course of a comprehensive investigation for the development of the electrical process for the dehydration of oil-field emulsions, the writer has had an unusual opportunity to direct and execute a number of related, parallel studies concerning crude oil emulsions and extending over a period of nearly six years. Among these was an investigation utilizing the microscope for studying both the general characteristics of crude oil emulsions, the nature of their electrical charge and the action of an alternating current field in causing coalescence of the finely dispersed, more or less permanently suspended, emulsion particles into larger droplets of such mass that subsequent dehydration would follow by the ordinary process of settling, further agglomeration of the water droplets and, finally, separation into commercially dry, pipe line oil and a clean water discharge. It is not the purpose of this paper to enter into a detailed discussion of the highly specialized subject of microscope technique, nor into a theoretical discussion concerning the origin of the electrical charge on the emulsion particle or concerning the mechanism of the electrical phenomena occurring during the electrical treatment of oil-field emulsions. In a short paper of this character one can hope to touch on only a very limited discussion of the theoretical aspects of crude oil emulsions. The subject of emulsions and colloids is comprised in a comparatively young science in which, however, very rapid progress is being made and consequently it is undergoing many changes; a tentative conclusion valid today may be overthrown tomorrow. Nor would it be a simple science even if it were no longer undergoing this rapid progress; a thorough study of emulsions is based upon a knowledge of such fundamental subjects as molecular structure, ionization and other electrical phenomena, surface chemistry, surface and interfacial tension phenomena, viscosity and other factors too numerous to discuss here and the fundamental theories of which are still undergoing more or less change. Therefore this paper will confine itself largely to a generally descriptive discussion, a sufficiently detailed outline of the microscope technique and a brief comment on

Jan 1, 1931

By John T. Norton, V.G. Mooradian

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By V. G. Mooradian, John T. Norton

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By James Bowron

Considering the importance of the steel trade and the strategic position occupied in it by the Birmingham district, it may be surprising to many to learn that the first pig iron smelted with coke was made in Alabama on Feb. 28, 1876, although merchant pig iron had been produced in Rockwood, Tenn., in 1867 -a plant that is still in operation The heavy deposit of Clinton ore, extending from Pennsylvania into Alabama, varies greatly in accessibility, on account of geological changes such as erosion or anticlinal upthrow; it varies equally as much in thickness and in quality. The brown ores extensively scattered through the South also vary materially in quality—some are relatively low in phosphorus and high in manganese, and vice versa. The red ore varies materially in phosphorus, but the iron produced from this ore was always considered too high in phosphorus for treatment by the acid bessemer or open-hearth process and did not contain sufficient phosphorus for the basic bessemer process. Under these conditions there remained only the basic open hearth as a possible process; and for many years it appeared impossible to use this, because, with coke smelted iron, the silicon was too high to permit its use in basic lined furnaces. Various attempts were made, from time to time, to produce a low-silicon iron, by carrying high lime burdens together with harder blowing, but the blast furnaces of the South were not equipped with the blowing power of today and from 31/2to 5-lb. pressure was the normal working condition. The result of these experiments, therefore, was that a furnace would get a lime set or be hastily changed to avoid scaffolding, and engineers and superintendents were careful not to renew the experiments. After the development of the beds of dolomitic stone in East Birmingham, the carrying of sufficient lime to bring down the silicon in the blast furnace to the permissible open-hearth limit was successfully done at the Alice furnace in Birmingham, commencing July 22, 1895. In a very short time the entire output of that furnace was being sold to different Northern steel manufacturers, with a guarantee that silicon and phosphorus should run below 1 per cent.

Jan 1, 1925