Search Documents

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By T. B. Counselman

An iron blast furnace of 1000 tons daily capacity will produce a 100,000 cu. ft. per minute of blast-furnace gas. This contains a 25 per cent of carbon monoxide, and has a B.t.u. value of about 95. gas is used primarily for heating the stoves of the blast furnace, secondarily, under boilers, for steam production. Occasionally it is used in gas engines. The raw gas coming out of the furnace carries about 10 grains of dust per cubic foot of gas, under best operating conditions. With furnace "rolling" or slipping, this quantity may temporarily be gre increased. This dust would, of course, deposit on the checkers o: stoves, or plug the burners under the boilers; therefore the gas : be cleaned. Flow Sheet The first step in the cleaning operation, as shown by the flow s Fig. 1, is a dry dust catcher, of which there are several forms, partially cleaned gas next goes to a primary wet washer, where v sprays knock down most of the solid particles. If further cleani desired, the gas may then go to electrical precipitation. Again, the removed is collected in water. Dry dust catchers reduce the dust col from 10 grains to between 4 and 6 grains per cubic foot, and rec roughly half of the total flue dust in the gas. The wet washers rea most of the remaining dust, reducing the dust content to about 1/4 per cubic foot. Electrical precipitators, if used, further reduce the content to about 0.01 grain per cubic foot of gas. The flow sheet s the dust content of the gas at various steps in the treatment and als content of solids in the water. It should be noted that some plant less water on the primary wet washer than indicated, and that ofte solids content of the scrubber water will be 300 grains per gallon, or much higher. Reasons for Recovering Flue Dust.—There are two main incentive recovering flue dust from the scrubber water: (1) the value of the (2) stream or lake pollution, where such a reason applies.

Jan 1, 1937

By F. H. Wilson

Copper base alloys containing various amounts of aluminum and silicon are of considerable commercial interest. In particular the alloy containing 7 pct aluminum and 2 pet silicon shows an attractive combination of high strength with excellent, machinability. Since there is no evidence ill the literature that this ternary system has been studied since the recognition by Smith1 and Anderson2 in 1939 of the kappa phase of the binary copper-silicon system, the determination of the equilibrium phase relationships in the copper corner of the ternary diagram has been undertaken to provide a fundamental basis for understanding the behavior of these alloys. Phase boundaries have been determined by the micrographic examination of quenched samples while points on the liquidus surface have been obtained by thermal analysis. The results, of sufficient precision to serve their major purpose of providing a guide for the control of the manufacture of alloys in the region covered, are presented in a series of both isothermal and vertical sections of the diagram. Alloys StVdied For a rough survey of the copper corner of this ternary system the compositions listed in Table I (Series A) were employed. The results of examinations of these alloys indicated that the compositions listed in Table 2 (Series B) would further clarify regions of greater complexity. All alloys were prepared as 1200 g heats, the copper being melted under charcoal, and then first silicon and then aluminum were added. An excess of 0.05 pet silicon was allowed to cover deoxidation losses. Two small bars 5/8 by 1 1/4 by 5 1/4 in. were cast using Durville type casting equipment. Ailalyses were made on all alloys using material which was hot-rolled at 800 or 850°C and annealed 17 hr at 650°C. All analyses were found to be within 0.05 pet of the nominal composition. Since the precision of analysis is not much better than this, the points of both isothermal sections and vertical sections at fixed aluminum and silicon contents have been plotted at the compositions indicated by the nominal composition.

Jan 1, 1949

By P. Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occurring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, Calif. recovers potash from natural brines, but uses fuel to accomplish evaporation. Solar evaporation is always desirable, because of low costs, however artificial evaporation may be economical if a group of very valuable salts are recovered. This is the case for the American Potash operations at Trona. Solar evaporation is limited by low working temperatures, which in most areas of the world is between 18 and 45°C. In many cases the average working temperature is about 25°C. However, solar evaporation will have to accommodate itself to the highs and lows of each 24 hour period, and to the different average temperatures during the months of the year. Therefore, solar evaporation, although more economical than artificial evaporation, has a tem- perature limit which greatly reduces the chances of its application. The feasibility of solar evaporation as a means of recovery of values from a particular brine, may be evaluated by the use of phase diagrams showing the several components present. This paper is restricted to the five component system: C1-, SO4=, Na+, K+, Mg++, and H2O, which correspond to brines found at Wendover, Utah, the Great Salt Lake, and sea water bitterns. THE BONNEVILLE OPERATION AT WENDOVER, UTAH For more than 25 years Bonneville, Ltd., now a division of Standard Magnesium and Chemical Co. (recently acquired by Kaiser Aluminum and Chemical Corp.), has been recovering potassium chloride from the brines found in the desert area just east of Wendover, Utah. Solar evaporation of the brines is possible as a consequence of relatively low precipitations (year average: 4.8 in.), and of dry and hot summer months. The brine, collected by a series of approximately 67 mi. of ditches crossing the desert, is fed into solar evaporation ponds. Evaporation which takes place from around the middle of May to about the end of September, permits the crystallization of approximately 90% of the originally present NaCl on what is called the "General Pond Area". Further evaporation,

Jan 1, 1964

By Chester A. Fulton

APATITE, the most abundant crystalline phosphate mineral, is found in igneous rocks and probably is the primary origin of all other phosphates, whether mineral or organic. Its chemical formula may be expressed as Ca5(Cl,F) (PO4) 3. The chlorine may be replaced almost entirely by the fluorine. It is found in large or small hexagonal prisms, usually of a vitreous luster and a green or red color, but also violet, white, or yellow. It is found largely as an accessory mineral in granitoid rocks. Its hardness is 4.5 to 5 and its specific gravity is about 3.2. There are many other phosphate minerals-for instance, amblygonite, autonite, collophane, lazulite, monazite, pyromorphite, torbenite, triphylite, turquoise, vivanite, wavellite-with base elements of calcium, magnesium, iron, aluminum, manganese, lead, cerium, lanthanum, lithium, or several of these in combination and with various amounts of water of crystallization. However, these phosphate minerals have but little value save as specimens for mineral collections, the exception perhaps being turquoise. While large deposits of igneous apatite are mined today for the production of fertilizers and chemicals, more than 90 pct of the world phosphate production is derived from secondary apatites, called phosphorites. These calcium (and magnesium, aluminum, and iron) phosphates have been formed in the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rocks containing apatite, bone deposits of prehistoric animals and marine life, or guano deposits (excreta of birds). These phosphorites are mostly alterations of phosphatic limestones that took place slowly over many years. Whether it is apatite or phosphorite that is being produced, it is known in the trade as "phosphate rock." The sedimentary phosphate deposits are of marine origin. Some, as laid down, were rich in phosphate or have become so by subsequent subaqueous action and have not been further enriched since emergence from the sea. Some were originally phosphatic limestones or marls from which calcium carbonate was dissolved away by waters containing carbon dioxide, in which calcium carbonate is much more soluble than

Jan 1, 1949

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the ['tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the ['tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By G. I. Madden, L. H. Van Vlack

WhEN basic refractories which contain peri-clase, MgO, are used in steel furnaces, they are altered by iron oxide to form magnesiowiistite, (Mg,Fe)O, and an iron-rich magnesioferrite, (Mg,Fe)Fe2O4. Silica, which is usually present, produces a silicate liquid that surrounds the solid phases. The individual crystalline grains of the above two solid phases grow at elevated temperatures. Previous papersL" showed that, if either periclase or magnesiowiistite is present as the only solid phase, its grain size increases in proportion to temperature and in proportion to the square root of time; the growth rate is reduced slightly if the amount of silicate liquid is increased. Similar results have been observed for iron-rich magnesioferrite.3 To determine the effect of the presence of two solid phases on the rate of grain growth, micro-structural studies have been made on samples containing both magnesiowustite and magnesioferrite. The experimental procedure was the same as that followed in the previous studies of this type.'12 Briefly, this included determination of compositions from the available phase relationships4 that would produce the two phases of interest at the firing temperature and using reagent-grade raw materials to prepare mixtures of these compositions. The mixtures were pressed into pellet-size samples and then fired at the desired time and temperature. The samples were water-quenched to preserve the microstructure present at the firing temperature. Standard reflected-light metallographic techniques were used for sample examination and sample analysis. Grain sizes were determined by measuring the mean diameter of a number of randomly selected grains in a two-dimensional microsection. A large cross section of the sample was covered to prevent biased data resulting from such effects as localized differences in the radius of curvature of the crystal grains. Examination indicates that grain growth is restricted when more than one solid phase is present. This is illustrated in Fig. 1 for: (a) magnesiowustite plus a silicate liquid; (b) magnesioferrite plus a silicate liquid; and (c) magnesiowiistite and magnesioferrite plus a silicate liquid. Fig. 2 plots the

Jan 1, 1964

By Raymond Howe

SOME time ago,, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furnace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to, the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after 4 years' service so a steam-pressed lining was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in- blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion.

Jan 9, 1919

By H. R. Fife

AN extended study of dustproofing Freeport-seam coal has empha-sized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption proper-ties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measure-ments on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average ton of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by sur-face area. Wax extraction data on 1-in. to 0 slack from mine-run treated Free-port-seam coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness.

Jan 1, 1937

By Berke L. Thompson

INTRODUCTION Purpose of Wall System There were 2379.88 m (meters) of tied back wall along Interstate 77 in the Capitol Complex area in Charleston, West Virginia. The main purposes of this wall system was for aesthetics, reduction of excavation, saving the forested slopes, and control of sloughage of the back slopes onto the Interstate. Failure At 1 PM on Thanksgiving Day, 1982, 3 wall panels fell from the insitu position onto the interstate in a matter of seconds. See Fig. 1. The total length of wall that fell was 29.25m. The height of the three panels varied from 10.06m to 10.36~1 and each individual panel had a length along the highway of 9.75m. These were abutting panels that were approximately in the middle of a section of wall 165.81m long. The panels separated from the remainder of the wall at 2 expansion joints that occur at the ends of every 3rd panel. The reinforced portland cement concrete panels were designed on a 76.2mm (millimeter) batter. See Fig. 2 for Wall Dimensions. The footer for these panels was lm wide, was keyed into sandstone bedrock 0.30m and was approximately 1.52m below the portland cement concrete pavement and shoulder. Thirteen of the 17 panels in this section of wall were tied to the sandstone bedrock behind the wall by either 25.4mm or 34.93mm hollow rock bolts. Two panels on each end of the wall were cantilever type walls. The panels that failed had 25.4m hollow rock bolts. A portion of each panel adjacent to both sides of the failure was pulled out from the rock face and appeared to be in imminent danger of also failing. All of the 21 rock bolts in the panels that fell were separated either at the backface of the wall, in the extension from the wall to the rock face or at the rock face. None of the rock bolts had been pulled out of the bond length in the sandstone bedrock. After considering the condition of the wall and

Jan 1, 1984

lv. H. Blauvelt, Great Falls, Montana (communication to the Secretary): In his remarks on Mr. Stetefeldt's paper (Trans., xxiii., 587)) Mr. Goetz observes: " Trouble experienced with producers at Great Falls influenced me to try Taylor producers instead of those of Wellman. But recent reports show that the Wellman producers work better, besides coating nearly 50 per cent. less than Taylor producers of equal capacity. Indiana and Illinois coals cannot be used in the Taylor producers by reason of the large size and hardness of the clinkers which they form." I think that Mr. Goetz must have been misinformed regarding the work of this producer in Illinois. One of the large mauafacturing concerns in that State, the Illinois Zinc Company, situated at Peru, which uses a coal mined in the vicinity, tried one Taylor producer, some four years ago, in competition with those of an older type, which it had been using. As a result of this trial, the company has now thirteen Taylor producers, which have been in operation for about three years. A recent report from these works says that the Taylor producers have largely reduced the loss of coal through the grate, and have also improved the quality of the gas, as compared with that produced from the same coal in the producers of the older type. This Illinois coal is, perhaps, the worst in the country for making gas; since, besides containing from 20 to 40 per cent. of ash, it carries a large quantity of pyrites, so that the clinkers are large and extremely hard, and the capacity of the producer is most severely tested.

Jan 1, 1895

By E. Gaujot

IN connection with the question of coal waste and economy in mining, we would call the attention of those interested to an apparatus invented by M. Dernencourt, Superintendent of the Anzin Division of the Anzin Coal Company, North of France. This apparatus is known in France and Belgium under the name of prop screw jack (vis botte), and has been used with good results in the above-named countries for some years past. M. Ponson gives, in his " Traité de l'exploitation des Mines," a description of it (page 533), but as the description given is old, the work not widely known in this country, and as some valuable improvements have been made since, I thought it might be useful to give a description of it, having seen it in operation in 1867, while in Europe to attend the great Exposition, and on a scientific tour to the mining districts of France, Germany, Belgium, and Italy. The prop screw jack is composed of the following pieces: I. The body or column B, Fig. 4 [Plate (1)], of oak or yellow pine, sawed square, the bark taken off, and any length, proportionate to the vein. The smallest are 10 inches diameter at the base, and 9 inches at the top, the height being from 12 to 15 inches less than the size of the vein. In the axis of this column, and at the top end, is a cylindrical opening or hole, C, 2 3/4 inches diameter, 10 inches deep, for the screw, S. II. Two wrought-iron rings, R R, to strengthen the two extremities of the column ; the rings must be put on hot. III. A cast-iron washer, E, with hole in centre a little larger than the screw, to be put on the top of the column, and on which the nut is to rest; the top side of this washer must be faced on the lathe, also the bottom of the nut, to prevent friction. IV. The screw, S, having a total length of 12 inches and a diameter of 21/2 inches (for very high veins this diameter may be in¬creased to 3 inches), and has on its top a wrought-iron plate, T,

Jan 1, 1873

By E. P. Pfleider, W. G. Pariseau

Even as the rational selection of excavation equipment requires a matching of machine performance capabilities to rock response characteristics, the functional features of transportation systems must be matched to the characteristics of the materials handled in order to secure optimum, trouble-free operation. In particular, ore passes and chutes must be designed for flow in order to insure controlled draw whenever a chute is opened. The alternative to quantitative design is, of course, the well known ad hoc procedure of freeing plugged ore passes, cleaning up spillage from flooded chutes, etc., after installation of the system. Since the voluminous empirical work sporadically undertaken through the years evidently had not led to reliable design methodology, it seemed worthwhile to attempt a rational and complete description of the movement of material through ore passes. The concepts of de- formable body mechanics applicable to gravity-induced flows of granular media or "soils" were involved. Accordingly, the mathematical theory of soil plasticity was adopted as a working hypothesis, and a two-dimensional laboratory model of an ore pass constructed in order to investigate the appropriateness of the theory. The general experimental strategy consisted of formulating the movement of material in ore passes as a boundary value problem in soil plasticity, determining the required boundary values of stress and velocity experimentally, and then using these data for the initiation of a theoretical solution for stress and velocity throughout the moving mass of material. A comparison between the theoretical and experimental constituted the test of the original hypothesis.

Jan 6, 1968

By Gerhard Derge, Harold Markus

The first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from 1.12† volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. Experimental Data Cations.—The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.1 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 10-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By Harold Markus, Gerhard Derge

The first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from 1.12† volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. Experimental Data Cations.—The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.1 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 10-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By A. S. Yue

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of. Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

By Joseph Chalmers, J. S. Desmond, R. Van A. Mills

[Because of the limited space in this volume and the fact that a description covering the oil recovery buildings and equipment (see page 4, Technical Publication No. 144) will be given in a forthcomnig U. S. Bureau of Mines publication, and because the paper was published in detail as Technical Publication No. 144, and is available as a separate at the Institute, it is impossible to include here more than the following brief extract.] Problems Being Studied The selection of the first problems to be studied was based largely upon the following very practical questions asked by several of the largest operators in the Mid-Continent field. 1. What are the causes for the formation of excessive amounts of bad thick oil on properties that are being repressured with compressed air and how can this trouble be prevented? 2. Why, in some areas, does the oxygen in the air injected into an oil sand during repressuring operations apparently change to carbon dioxide? Is carbon dioxide formed by the oxidation of some of the oil in the sand'? How can the formation of inert or low B.t.u. casinghead gas, loaded with nitrogen, carbon dioxide and oxygen, be prevented? 3. What percentage of the oil originally present in an oil sand can be recovered by the ordinary methods of operation when the gas originally dissolved in the oil is the main propulsive agent? 4. What percentage of the amount of oil produced by ordinary methods can be recovered under average conditions by repressuring a so-called depleted oil sand? 5. What are the relative propulsive efficiencies of compressed air and natural gas in repressuring operations? 6. What are the practical advantages of pressure maintenance and early repressuring as compared with late repressuring?

Jan 1, 1929

By R. R. Seeber

In the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large—from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.' The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting ing-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. The hoist for No. 4 shaft is about 1,700 ft. from the power-plant, arid in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-geaerator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-km, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels

Jan 1, 1911