Search Documents

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors' work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By J. Serra, M. Turpin, R. Alberny

A new method is proposed to obtain automatically an unbiased estimate of the interdendritic spacing A. It is shown that the structure can be built by a random distribution of a rectangular basic unit. The usual definition of the interdendritic spacing yields a value 1 which, coupled with A, gives the shape of the basic rectangular unit. A study of the relationship between dendrite arm spacing and solidification rate was conducted as a part of a research program on dendritic solidification. For any comparison between theory and experiments to be meaningful, it is necessary to measure reproducible and clearly defined spacings. Fig. 1 shows clearly that even in a fairly simple structure such measurements are difficult. if we compare photos (a) and (b), we can hardly assess which one shows the larger spacing. Moreover, the quantity to be measured can be defined in several ways. On a small scale, dendrites seem to be distributed in a very regular and ordered way. However, on a larger scale, this regularity no longer exists. The usual way to measure spacings is to pick up some rows of dendrite stalks; such measurements are obviously biased since less orderly regions are not taken into account. A more objective method is to section the picture with randomly oriented straight lines and average the measured interdendritic spacings. The purpose of this paper is to show that such measurements, which can be conducted automatically, yield objective and reproducible results which are directly related to characteristic features of the dendritic structure. I) THEORETICAL ANALYSIS 1-1) Mathematical Morphology and Function of Co-variance. Matheronl and Serra2 enlarced- the definition and geometrical meaning of the notion of covariance to encompass problems in mathematical morphology. A brief review of part of their theory can be stated as follows. Let A' be an isolated particle, and let us consider a group of two scanning points h is the vector joinlng these points, h its modulus, and a its direction. Let us also define a boolean function, k(x), whose value is 1 if x lies inside the particle and 0 if it 1s outside. The total number of events in which both points are inside A' IS the covariance Ii',(h): is the measure of the intersection of A' with the particle ALh obtained by translating A' of -h Obviously K,(O) is the volume of the particle A', or its area if A' is a two-dimensional body. The average value of K,(h), when the direction of a vector h of constant modulus is rotated, is: An important property of the covariance is illustrated on Fig. 2: if the shape of a particle shows some regularity along a direction a, K,(h) generally presents a maximum. We now consider a group A, made of many particles A' distributed in space; then k(x) is taken as the realization of a stationary random f~nction.~ The volume fraction (or fraction of area if the problem is two-dimensional) occupied by A equals the average value q of k(x): meaning "average value of"). We also replace

Jan 1, 1970

By D. A. Flanagan, P. B. Crawford

A study has been made of the feasibility of storing liquid meihane at low pressures in undergrohd caverns. Methane liquefies at — 258°F at atmospheric pressure. It is shown that the methane evaporation rates will rapidly decrease and cool the surrounding rock so that at the end of one month they would be between 50 Mcf/hr for a cavern of 25-ft radius and 700 Mcf/hr for a cavern of 100-ft radius. At the end of 10 years, the evaporation rates would be 18 and 100 Mcf/hr, respectively, for caverns of the same radii. The evaporation rates may be reduced by a factor of 2 to 10 by the application of insulation. The cost for mining the caverns is estimated to be $.75 to $1.25/Mcf of storage. This is substantially less than surface storage; it is believed to be safer and to result in lower maintenance, savings in space and savings in strategic materials. INTRODUCTION During the past few years, there has been an increasing interest in the economic feasibility of liquefying methane. Methane liquefaction is being considered for tanker transport; in addition, liquefaction is being reconsidered for shaving peak gas demands. Several articles have described natural gas liquefaction and the progress of the tanker in making trial runs from the United States to Great Britain to determine the feasibility of tanker transport. At the present time, pipelines are not designed to supply peak gas loads during extremely cold periods such as are oiten encountered in the North and Northeast. Gas is being stored in underground reservoirs en-route to its destination, but in many instances satisfactory storage in porous reservoirs has not been practical, especially along the Eastern seaboard where few petroleum reservoirs have been found. In England and other foreign countries, it is unlikely that satisfactory porous structures could be found, and it may be desirable to mine or excavate the rock to obtain storage. By storing the methane near the consumption point, product availability can be increased during periods of need. Methane liquefies at - 258OF at atmospheric pressure, and 1 cu ft of liquid methane will make about 600 cu ft of gaseous methane. Methane liquefaction for shaving peak gas demands was conducted in Cleveland, Ohio in the early 1940's. The Cleveland plant was designed to liquefy 4 MMcf/D of natural gas.' Development of several low-temperature processes has resulted in some improvements in the design of low-temperature storage vessels. Liquefied-methane storage vessels can be designed for various evaporation rates. The desired rate will depend on the reason for liquefaction. For shaving peak gas demands, the desired evaporation rates would be low, possibly between 0.2 and 1.5 per cent/day. For methane tanker transport and supply, the evaporation rates must be high and must equal the total daily rate of supply. It is apparent that the cost of storage facilities will depend on the objective and will vary appreciably. Surface storage of methane may cost between $3,000 and $20,000/MMscf, depending on the size and design. The failure of the surface storage vessels at Cleveland, with the resulting injury and loss of many lives, has caused considerable emphasis to be placed upon developing new, safer and improved methods of storing liquid methane. Storage of liquefied propane and butane in underground salt domes has been very satisfactory. The per-barrel cost of underground storage for any sizeable capacity is very small compared to the cost of surface storage for LPG mixtures. The larger the capacity of the underground storage, the less is the per-barrel cost. Numerous advantages appear to exist if liquefied methane could be satisfactorily stored underground, the principal advantages being increased safety, lower initial cost, lower maintenance cost, savings in space and savings in strategic materials. The purpose of this paper is to determine the feasibility of storing liquid methane underground in mined caverns. If a large spherical cavern is dug underground and is filled instantaneously with liquid methane, the surface of the sphere may approach the liquid methane temperature almost instantaneously. The temperature distribution for a sphere of radius r. in an infinite medium, initially at one temperature with spherical surface kept at T, from time t = 0, is given by Eq. 1.'

By P. Chiotti, J. T. Mason

Ther?nal, X-ray, metallographic, and vapor pressure data were obtained to establish the phase diagram and standard free energy, enthalpy, and entropy of formation for the compounds in the Sw-Zn system. Four compounds, SmZn, SmZn2 , SmZn4.s, and SmZn8.5, melt congruently at 960°, 94Z°, 908°, and 940°C, respectively. The cornpounds SlnZns, Sm3Znll, and SnzZn7.3 undergo peritectic decomposition at 855", 870°, and 890C, respectively. Another compound of uncertain stoichiometry, SmZn11, undergoes peritectic decomposition at 760°C. Four entectics were observed with the following compositions in weight percent zinc and eutectic tenzperatures in degrees Centigrade: 12 pct, 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. An allotropic transformation and a composition range were observed for the SmZnz compound. The transfor)nation varies from 905" to 865°C as the zinc content increases from 16.0 to 48.5 wt pct, respectively. The free energy of formation of the compounds at 50PC varies between -15.9 kcal per mole for SmZn to -51.1 kcal per mole for SmZn,.,. Corresponding enthalpies vary between -19.2 to -78.3 kcal per mole. The ther-modynamic properties for the liquid alloys are described by the relations: A search of the literature revealed very little information on the Sm-Zn system. Chao et al.&apos; as well as Iandelli and palenzonai have reported the structure of SmZn to be cubic B2 type and Kuz&apos;ma et al3. have reported the structure of -sm2zn17 to be of the Th2Ni17 type. The purpose of this work was to establish the phase diagram of this system, to determine the zinc vapor pressure over the solid two-phase regions of the SYstem, and to calculate the thermodynamic properties of the compounds. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in this investigation were Bunker Hill slab zinc 99.99 wt pct pure and Ames Laboratory samarium. Analysis of the samarium by chemical, spectrographic, and vacuum-fusion methods gave the following average impurities in ppm: Nd, <200; Eu, <100; Gd, <100; Y, <50;Ca, 225; Ta, 400; Mg, 10; Cu, ~50; 0, 175; H, 20; and N, 15. The elements Fe, Si, Cr, Ni, Al, and W were not detected. The samarium was received as sponge metal and was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys with zinc contents up to the Sm2Znl, stoichio-metry. At higher zinc contents the grain boundaries of the tantalum containers were penetrated by the alloy and the containers failed during prolonged annealing. About 25 g of massive zinc and samarium sponge were sealed in tantalum crucibles equipped with thermocouple wells. These crucibles were in turn sealed in stainless-steel jackets. All closures were made by arc welding under an argon atmosphere. The samples were equilibrated in an oscillating furnace and in some cases were given various heat treatments in a soaking furnace. After appropriate heat treatment the steel jackets were removed and the alloy subjected to differential thermal analysis. The apparatus was calibrated against pure zinc and pure copper and found to reproduce the accepted melting points within 1°C. Alloys were subsequently subjected to metallographic examination and those of appropriate compositions were used for X-ray diffraction analysis and for zinc vapor pressure determinations. The vapor pressures were determined by the dewpoint method. Both the differential analysis and dewpoint measuring apparatuses have been described in earlier papers.4, 5 All alloy samples were etched with Nital (0.5 to 3 pct nitric acid in alcohol) except the samarium-rich alloys. These more reactive alloys were electro-polished in a 1 to 6 pct HClO4 in methanol solution at -700c at a potential of 50 v. EXPERIMENTAL RESULTS Phase Diagram. The results of thermal analysis are indicated by the points on the phase diagram, Fig. 1. Eight compounds and four eutectics were observed. The composition of the compounds and their melting or peritectic temperatures are given on the phase diagram. The four eutectic compositions in wt pct zinc and eutectic temperatures in % are: 12 pct,- 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. The stoichiometry of the most zinc-rich compound is still uncertain, but is very likely either SmZnll or SmZnlz. However, to simplify the presentation which follows it will be referred to as SmZnll. As shown on the phase diagram the phase regions for some of the samarium-rich alloys have not been unambiguously established. A sample of pure samarium was observed to transform at 924°C and to melt at 1074"C, in good agreement with corresponding val-

Jan 1, 1968

By Shiro Ban-ya, John Chipman

The effects of many alloying eletnents on the acticity coefficient of sulfur in liquid iron have-been studied by the equilibriutn in the reaction Sfin Fe) + Hz = HzS at 1550°C&apos;. Results are expressed in terms of a concentration variable for a nonmetallic or for a substitutional metallic solute. Activity coefficient of sulfur, defined as increased by B, Al, C, Si, Ge, Sn, P, As, Sb, Mo, W, Co, and PI. It is decreased by Cu,Au, Ti. Zr, V, h&apos;b, Ta, Cr, ,23n, and Ni. Irulues oj. the interaction coejficient 0i = 6 In are labulated. The same interactions are expressed also in terms of atom fraction and of weight percent. The thermodynamic properties of sulfur in liquid iron have been fairly well established. Our recent paper1 reported new determinations of activity coefficient up an atom fraction of 0.12 and equations based on a careful review of all published data. The effects of alloying elements on the activity of sulfur have been studied by several investigators,2"11 especially by Morris and Williams for silicon,&apos; by Morris and Buehl for carbon,~ and by Sherman and Chipman for manganese. phosphorus, and al~minum.~ However, the effects of some important alloying elements remain to be determined. The purpose of this investigation was to determine the effects of many alloying elements on the activity of sulfur in Fe-S-j ternary systems. EXPERIMENTAL METHOD This study was based on experimental determination of equilibrium in the reaction at 1550°C: The same apparatus and procedure as described in our previous paper have been retained, and the same corrections were applied for dissociation of H2S. The alumina crucibles used in the experiments consisted of four separate compartments. In a given experimental run. kach of three alumina crucibles held four different samples of about 3 g each which reached equilibrium in the same gas atmosphere and temperature. The charges were made up of electrolytic iron, pure iron sulfide, and desired alloying elements, which were pure metal or master alloys made in the laboratory. The weighed samples were held for 4 to 12 hr in the prepared atmosphere at 1550°C. They were then low- ered to be cooled as quickly as possible. The quenched metal beads were crushed to avoid the errors of segregation in the ingot. The sulfur content was determined gravimetrically and alloy content by appropriate chemical analysis. CALCULATIONS The apparent equilibrium constants of Eq. [I] are expressed as follows from the corrected gas ratios and sulfur concentrations: The term K" is the observed equilibrium constant in any given ternary solution, K&apos; is the value for the Fe-S binary solution. and the limiting value of K&apos; in the infinitely dilute solution is designated by K, which is the true equilibrium constant in Eq. [I]. In the thermodynamic treatment of nonmetallic elements in a metallic solution, it has been suggested1&apos; that the lattice ratio has certain advantages over other variables to express the concentration of solute. In interstitial solid solutions the lattice ratio zj is proportional to the ratio of filled interstitial sites to those which remain unfilled. The equations derived for the activity of the solute using zj as the concentration variable are found also to be applicable to liquid solutions containing nonmetallic solutes when the nonmetal is treated as if it were interstitial. For this purpose we adopt the following definitions: The quantity vj which is negative for interstitial solutes is taken as -1 for nonmetallic and +1 for metallic solutes. For purposes of calculation however ; j may be assigned a value which results in a linear relation such as shown in Figs. 1 to 15. The activity coefficient of sulfur, Qs, and equilibrium constant. K(z). are defined as follows: According to a Taylor series expansion. the logarithm of the activity coefficient of sulfur in Fe-S-j ternary system is: However, the value of 6 In */6zi remains constant through a broad range of dilute solutions and the terms of higher order are negligibly small. As a consequence, Eq. [6] is simplified as follows:

Jan 1, 1970

By C. D. Michaelson

The memory of D. C. Jackling serves chiefly to remind us how much we owe to the pioneers of our industry. Jackling was one of the giants. Orphaned at the age of two, he made his way through sheer persistence and plain hard work. His brilliance gave rise to a vision, and his tenacity made his vision a reality. Foreseeing that economies of scale would make the handling of low-grade ore profitable, he introduced the revolutionary concept of open-pit copper mining. During World War I, the defense effort of the United States was immeasurably strengthened by the tremendous supplies of copper from the western mines that Jackling had made possible. Again in World War II, the demands for copper were supplied, and the nation once more had profound reason to be grateful to this rugged, stubborn man who had long ago ventured into the mountains and unlocked their wealth. We are now embarked upon another great era of change, and we must devise new concepts to meet it. The task is not only to create new techniques of mining, but to forge better ties between men and institutions which will let us work in harmony with the techniques we have. We might recall that while Jackling was a man of towering pride and formidable will, he was also adept at getting others to share his vision and join his purpose. Today our reach for cooperative endeavor must go far beyond our own shores as we seek to develop the buried riches of distant lands. And we would do well to remember that Jackling&apos;s remarkable insight would have come to nothing had not British investors been willing to provide much of the initial capital. As was true of so many early enterprises in America, European capital was absolutely essential.

Jan 4, 1969

By E. W. Pehrson, J. W. Furness

NONMETALLIC MINERALS, exclusive of fuels, may be divided into three groups: Building materials, fertilizer minerals, and miscellaneous minerals. Building materials, such as sand, gravel, slone, lime, and the ingredients of cement and clay products, occur widely in nature and are thus available near consuming centers at relatively low prices. Cost of transportation over great distances deters any&apos; substantial movement in world trade. On the other hand, fertilizer minerals, such as phosphate rock, potash, nitrates, sulfur, and pyrite, and the miscellaneous nonmetallic minerals, such as long-fiber asbestos, mica, graphite, fluorspar, and china clay, do not have such widespread occurrence and consequently contribute the major part of the world&apos;s commerce in such minerals. The U. S. Bureau of Mines has prepared charts showing the inter-

Jan 1, 1936

The following is an incomplete list of members and guests who called at Institute headquarters `during the period Aug. 10, 1918 to Sept. 10, 1918. Amil A. Anderson, Hill City, S. D. A. A. Holland. H. G. S: Anderson, Hurley, N. Al. Paul S. King, Wilmington, Del. Louis A. Barton, Capt., Engineers, U. S. A. Herbert G. Officer, Washington, D. C. K. Baumgarten, lst Lieut., U. S. R. A. B. Parsons. Charles W. Boise, Belgian Congo. Robert R. Pollock, San Francisco, Cal. Henry C. Carlisle, The Pas, Manitoba. Frank A. Smith, Edgewood, Md. J. Ross Corbin, Boyertown, Pa. Edward C. Thompson, Kennett, Cal. S. Le Fevre, Forest Glen, N. V. Malcolm M. Thompson, Morsemere, N. J. Harold P. Ford, Cleveland, 0. Lester C. Uren, Berkeley, Cal. William L. Hogg, Waynesboro, Va. Harold W. Aldrich has been appointed assistant general superintendent of the Inspiration Consolidated Copper Co. at Inspiration, Ariz. Capt. Percy E. Barbour, formerly with the New York State Troopers, has been granted a leave of absence from the Department for the period of the war, by the Governor, and has been appointed Captain in the Engineer Corps, U. S. A. He served on the Mexican border in the New York State National Guard. A. C. Barke, formerly with the United States Smelting, Refining and Mining Exploration Co., has accepted a position with the United States Fuel Co. at&apos; Salt Lake City, Utah.

Jan 10, 1918

The Institute assembled in the room of the Board of Trade, Mercantile Library Building, on Tuesday evening, May 20th, at 8 o&apos;clock P.M, Hon. W. D. Kelley made an address of welcome to the Institute, which was responded to by President Raymond. The Council reported, through the President, that the Institute had during&apos; the past year, held three meetings, in New York, Pittsburgh, and Boston. Thirty-nine papers of great professional value had been read, and sixty-nine members and twenty-four associates added to the Institute. The finances of the Institute were in good condition, the report of the Treasurer, Mr. T. D. Rand, showing a balance on hand of $1569.74. The report was accepted. Prof. L. Gruner, of Paris, France, and Prof. Peter von Tunner, of Leoben, Austria, having been proposed by ten members of the Institute, and approved by the Council, were unanimously elected honorary members. The Council reported the names of the following gentlemen, with recommendation for election as members or associates. They were unanimously elected. *Barker, Prof. G. F.,.....Philadelphia, Pa. Chalfant, John W.,.....Pittsburgh, Pa. *Crawford, John J.,.....Philadelphia, Pa. *Crusius, O. H.,.Columbus, Ohio. Dibble, Theo. Hoyt,.....Pottsville, Pa. Everson, John,. Pittsburgh, Pa. Field, Robt. P.,.Philadelphia, Pa. *Fisher, F. A.,.Bristol, Tenn. *Fleming, W. E.,.Pioche, Nev. *Harden, E. B ,..Philadelphia, Pa. *Harding, G. E.,.New York. Hartshorne, J.,..&apos;Philadelphia, Pa. Haupt, H., Jr.,.Philadelphia, Pa.

Annual Meeting, Philadelphia May, 1873 THE Institute assembled in the room of the Board of Trade, Mercantile Library Building, on Tuesday evening, May 20th, at 8 o&apos;clock P.M, Hon. W. D. Kelley made an address of welcome to the Institute, which was responded to by President Raymond. The Council reported, through the President, that the Institute had during the past year, held three meetings, in New York, Pittsburgh, and Boston. Thirty-nine papers of great professional value had been read, and sixty-nine members and twenty-four associates added to the Institute. The finances of the Institute were in good condition, the report of the Treasurer, Mr. T. D. Rand, showing a balance on hand of $1569.74. The report was accepted. Prof. L. Gruner, of Paris, France, and Prof. Peter von Tunner, of Leoben, Austria, having been proposed by ten members of the Institute, and approved by the Council, were unanimously elected honorary members. The Council reported the names of the following gentlemen, with recommendation for election as members or associates. They were unanimously elected. *Barker, Prof. G. F., - Philadelphia, Pa. †Chalfant, John W., - Pittsburgh, Pa. *Crawford, John J., - Philadelphia, Pa. *Crasius, O. H., - Columbus, Ohio. †Dibble, Theo. Hoyt, - Pottsville, Pa. †Everson, John, - Pittsburgh, Pa. †Field, Robt. P., - Philadelphia, Pa. *Fisher, F. A., - Bristol, Tenn. *Fleming, W. E., - Pioche, Nev. *Harden, E. B, - Philadelphia, Pa. *Harding, G. E., - New York. †Hartshorne, J., - Philadelphia, Pa. †Haupt, H., Jr., - Philadelphia, Pa. * Members. † Associates.

Jan 1, 1874

By Raymond Sanford

IT IS difficult to know just when a hoisting rope should be removed from service and a new one substituted. It is desirable to utilize the full life of a rope but, on .the other hand, the damage and possible loss of life, resulting from delay in replacing it may amount to many times the cost of a new rope. In the present methods of inspection the inspector must rely upon accumulated experience and a certain sixth sense or intuition in addition to any rules that may be laid down regarding the number and distribu-tion of broken wires. This condition does not neces-sarily arise from lack of interest among users or makers of rope, but is due rather to the lack of satisfactory or adequate methods for testing ropes to determine their exact condition. The main difficulty in devising a physical test lies in the fact that a number of causes, all operating in different ways, contribute to the deterioration of a rope in service, and affect not only the external conditions but also the inner structure of the material of which the rope is constructed. Wear and broken wires on the outer part of the rope are not difficult to detect, but a test is needed which will clearly indicate the presence of broken wires in the interior portions and the change in strength due to alterations in the structure and properties of the material itself.

Jan 7, 1923

By Walter C. Labys

INTRODUCTION Interest in multicommodity stabilization schemes has increased recently for several reasons, a most important one being the experienced wide swings in primary commodity prices. These prices rose sharply between mid - 1972 and end - 1974 giving commodity exporting countries an opportunity to gain sizeable increases in export earnings. But since then, prices have tumbled and these countries are searching for a means to stabilize if not to increase their earnings. While this problem is particularly serious for developing countries, the developed countries are concerned about the impending upward price swing, which would increase inflation before recovery from the world recession is assured. As a direct consequence of the emergency meeting of the U.N. General Assembly devoted to commodity problems in April of 1974, interest has been renewed in the Keynesian (4) plan for an international multicommodity buffer stock program. In particular, UNCTAD (8) is designing an integrated commodity scheme to be discussed within that body. In terms of approaches that have appeared in designing such a program, none exist which relate to the interpretation of the independence and interdependence of prices of the commodities of interest. Typical criteria for selecting commodities for the scheme have included their importance in world trade, their particular origin from developing countries, and their feasibility for storage. But the financial management of a multicommodity buffer stock requires a consideration of commodity prices, yields, and risks as does as any portfolio of assets. The approach which we take in this study is that of application

Jan 1, 1977

By H. R. Deeth

NEPHELINE syenite is a sodium, potassium, aluminum silicate rock occurring in many countries. Large deposits have been investigated in Russia, India, and Norway and in the U. S., where it is known to occur in Arkansas, New Jersey, and Wisconsin. There are extensive areas containing nepheline syenite in south-central Ontario, a region surveyed in 1905 by Adams and Barlow. By 1925 considerable interest had developed in searching for aluminous raw materials that could be used by the glass industry. This finally focused attention on the nepheline syenite described by Adams and Barlow in 1910.1

Jan 11, 1957

Just three years after researchers announced its development, Dravo is putting the finishing touches on a new $60-million Thiosorhic lime mine/kiln complex near Maysville, Ky. Electric utilities in western Pennsylvania and Ohio have already signed long-term contracts for over three-quarters of the projected 907 000-t/v (1-million-stpy) production. Thiosorbic lime, a flue gas desulfurizing agent, proved in industrial testing that at high emission levels (greater than 3000ppm SO2) it could be twice as effective in SO2 capture as conventional lime, while eliminating the major problem of scaling and plugging of scrubber equipment.

Jan 4, 1977

Merritt: Karl, you are a native New Englander, having been born in St. Albans, Vermont, in 1885. How did you decide on becoming a mining engineer? Twitchell: While I was attending St. Albans High School, my uncle, who had been the American Consul in Kingston, Ontario, for many years, told me of the excellent mining school there. He also introduced me to a Canadian mining engineer who sparked my interest in mining by noting the possibility of achieving personal success without always being under salary. Well, that appealed to me, so I applied to the Kingston School of Mines at Queen&apos;s University.

Jan 9, 1965

By Gregory B. Baecher

Rock engineering involves uncertainties which are large and difficult to quantify. The traditional design approach to these uncertain- ties has been conservatism, and has been satisfactory to the extent that failure rates are reasonably small. Yet, a price is paid for conservatism, and that price is not always small. Today, reliability and risk analysis are finding use in rock engineering. The introduction of such methods, usually under the name &apos;probabilistic design,&apos; is controverisal. However, if the jingoism of both sizes in this controversy is stripped away, it appears that new insights about uncertainty in rock engineering are emerging.

Jan 1, 1982

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Mar. 10 to Apr. 10, 1915: Oscar Lachmund, Greenwood, B. C. Harvey B. Small, Mangaugue, Colombia. S. W. Ough, Pachuca, Mexico. M. F. Sayre, Schenectady, N. Y. B. W. Vallat, Detroit, Mich. James W. Hambleton, Parral, Mexico. Charles Mentzel, New York, N. I . Philip L. Gill, Woodmere, L. I., N. 1. M. K. Rodgers, San Francisco, Cal. John T. Fuller is President of the F. Shepherd Mining Co., operating at Rush Mountain, Ark.

Jan 5, 1915

Grad, the abbreviation for Graduate Resume Accumulation and Distribution, is a computerized information retrieval system operated on behalf of college placement officers around the country by the non- profit College Placement Council, Inc. Grad is free to all engineering candidates (regardless of the number of years of experience) and is a means of getting together college alumni who are seeking new employment and prospective employers. Who is Qualified? Candidates must have at least a bachelor&apos;s degree from a four-year college or university, or. in lieu of this, be accredited by a professional institute such as AIME as a full Member.

Jan 1, 1970

The University of Idaho Mining Society held a meeting on Oct. 23, and elected the following officers: President, Sam Bloom; Vice-President, Lloyd McDougall; Secty Treas, Jess W. Wade. Regular meetings are held on the first and third .Tuesdays of each month, for informal lectures and reports on technical subjects. The Mining Club of the University of Wisconsin has held four recent meetings On Oct. 17, sixteen new members were inducted, and a committee was appointed to buy a Liberty Bond. The second meeting, Oct. 31, was devoted to general entertainment, at the home of Professor McCaffery.

Jan 1, 1918

By R. A. Matuszak

Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed- torque characteristics to provide an optimum from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far, and improves the performance characteristics.

Jan 1, 1979