Search Documents

One of the most significant problems experienced in land reclamation work has been the tendency of earthmovers to over-compact the subsoils and topsoils. The need for extensive subsoil drainage, because of over-compaction, becomes a very expensive exercise and can be attributed to poor planning. The problem has been addressed both at the Waihi and Huntly open-cast mines through the use of low ground pressure machines in the placement of subsoils and contouring. The use of subsoilers working to contour to aerate the soils is essential to integrate both the sub and topsoils so that significant root growth and drainage is established. Waihi's rainfall (approximately 200 mm annually) and light soils create difficulties in preparing for the final seed bed. A noticeable factor in preparation of the growing medium was the reaction of the lime particularly in the subsoils (damp), from a lumpy, quite heavy texture to almost a seed-bed texture within a period of approximately 72 hours. Also the high incidence of stone and debris which was not apparent in the placement of subsoils meant the job became very labour intensive. This will be overcome with the importation of a machine from the USA. All of the rubber tyred tractors used on these projects are four wheel drive in the 6S-aOhp range which for weight distribution and the safety factors allows for good landscaping techniques. Good engineering practices should ensure that slopes of no more than 3:1 be designed, keeping in mind that the long term planning must allow for maintenance and stock management of restored land.  In the preparation of the final growing medium the equipment used included: Caterpillar 05 LPG and blade; three-four wheel drive rubber tyre tractors; Super flow subsoiler; hydraulic twin spinner manure spreader; discs û two types; harrows; MF Seeder; Cambridge Roller and Duncan Rotatiller.

Jan 1, 1991

By G J. Fleming

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within theAndaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra. Miwah mineralisation is associated with variably dipping structurally and lithologically controlled argillic and advanced argillic alteration. An oxidised supergene leached zone and a recent, thin, unaltered tuff blanket partly overlie the mineralisation. Mineralised zones are commonly brecciated and veined, and display quartz, quartz-alunite, quartz-alunite¦pyrophyllite¦kaolinite replacement assemblages, surrounded by more weakly mineralised, often vugghy quartzalunite¦pyrophyllite¦kaolinite advanced argillic, and argillic zones of quartz-kaolinite, quartz¦pyrophyllite¦kaolinite and smectite-illite-quartz. Propylitic assemblages are marginal to more intensely altered zones. Hypogene copper mineralisation is typified by enargite, luzonite, and covellite. The host mineral to gold is uncertain at present. Rare barite, native sulfur, and ?telluride also occur. Bornite and chalcopyrite have been observed in transported altered rocks in faults. Generally the mineralisation is anomalous in precious metals, locally enriched in Cu, erratic in Pb, and depleted in Zn, with a good correlation between Cu-As-Ag.

Jan 1, 1995

By B K. Hebblewhite, F T. Suorineni, J D. Tibbett

Block caving is an underground mining method that can provide high production capacities at low operating costs. This enables the profitable extraction of massive, low-grade orebodies and attracts industry towards the method. Block caving operations require significant initial capital investment and predictable cave propagation is crucial to safety and economic success. Lack of access to observe the caving process hinders our ability to learn how the rock mass and geological structures are reacting to mining. Virtual reality scientific visualisation (VRSV) enables the integration and investigation of multiple, large caving data sets and provides a viable alternative to visualise rock mass response without physical access to the cave. Point instrumentation is incapable of providing an overview of cave performance and seismic monitoring, while providing an overview of the rock mass and the response of structures to caving, is only useful when linked to the caving activities. The integration of point instrumentation data with seismic monitoring information, coupled with scientific visualisation of the mining system in a virtual reality environment, provides a powerful means for understanding caving performance.This paper describes the use of a VRSV module at UNSW Australia, designed for investigating the block cave mining system from a case study operation. This module has been used to investigate the location and chronological evolution of seismicity to understand sources of damage resulting in seismic space-time sequences (SSTS) in the caving system. The events within an SSTS represent damage that is spatially and temporally related. An SSTS group represents a collection of microseismic events from a reasonably competent region of the rock mass that has experienced a stress change significant enough to cause sequential damage. SSTS group locations have been seen to be the path of subsequent cave propagation. Thus, SSTS analysis enables insight to further our understanding of rock mass damage in caving geomechanics through analysis of historic data. Such insight has operational potential to learn from recent rock mass activity for optimising the management of undercut advance, draw front advance and cave draw patterns.CITATION:Tibbett, J D, Suorineni, F T and Hebblewhite, B K, 2016. Understanding damage source mechanisms in a caving system using virtual reality scientific visualisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 439–452 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Separation of Iron Particles from Banded Haematite Quartzite (BHQ) Ore by Selective Magnetic Coating The separation of fine iron particles from banded hematite quartzite (BHQ) has been studied using selective magnetic coating. The BHQ ore assays as 38.9 per cent Fe, 42.5 per cent SiO2 and 1.0 per cent Al2O3. Mineralogically, the ore contains hematite and quartz as the major mineral phases where as goethite and magnetite is present in minor entities. Natural magnetite of very fine size and oleate-magnetite in colloidal form, prepared synthetically in the laboratory are used as the coating material on the surface of hematite particles. The selective coatings of oleate-magnetite on BHQ surfaces followed by magnetic separation studies have indicated that, it is possible to achieve 62.3 per cent Fe with 8.5 per cent SiO2 at 85.4 per cent iron recovery. The recovery of iron values is found to be superior in comparison to the conventional magnetic separation techniques. The selectivity of coating for enhancing the magnetic response of iron particles is achieved by controlling the surface properties of the particle via electrokinetic potential adjustment by controling pH and addition of oleate-magnetite. In the separation process, the effects of pH, magnetic intensity and addition of oleate-magnetite are studied to achieve the maximum grade and recovery of iron values. The optimum separation is observed at pH of 7.5, oleate-magnetite concentration of 0.25 ml/g of BHQ ore and a magnetic intensity of around 0.8 Tesla. The X-ray diffraction (XRD), Infra-red spectroscopy (IR) and UV-visible spectroscopic studies strongly suggest preferential coating of magnetite on hematite surfaces. Scanning electron microscopy (SEM) studies have brought out the semi-quantitative features of BHQ ore. The recovery of iron values from a lean grade ore such as BHQ is carried out looking into the future needs of this ore in India for iron and steel making.

Sep 13, 2010

By R G. Barker

The NZ Minerals Industry Association has continued to advance the interests of the minerals sector through leading the establishment of a Minerals Industry Advisory Committee, and the preparation of a technology strategy with funding assistance from the Foundation for Research, Science and Technology. The current moves mirror those of more than 30 years ago when a government initiative led to a resurgence of exploration through amending the mining legislation, redirecting Government research priorities and tax changes. The economic and political and commercial environment in 2001 is very different from that of the 1960s and success of these new initiatives depends on the continuing support and involvement of all sectors of the minerals industry, and building an improved relationship with the Government and the public.

Jan 1, 2001

The Hyde-Macraes Shear Zone (HMSZ) is low angle, duplex thrust system that has developed in a graphitic pelite schist within the Otago schist belt, New Zealand . At Round Hill lateral ramps have developed parallel to the movement direction between+ the footwall and hangingwall shears. These structures exhibit normal oblique-slip displacement which has been an important mechanism for creating space in an otherwise compressional system. Gold-bearing quartz veins were emplaced along the boundary shears and lateral ramps during thrusting. Gold within the lateral ramps is coarse (up to 300 microns) however hanging wall cataclasite development in the boundary shears after the gold was deposited has reduced the grainzise of most of the gold to less than one micron. This bimodal gold distribution has metallurgical implications with respect to the maximisation of gold recovery at Macraes.

Jan 1, 1993

Industrial minerals and rocks are those which are economically important because of desirable physical and/or chemical properties rather than metal or energy content. The evaluation of these resources for investment purposes in general follows established procedures after due consideration of well documented input data. However, in view of the sensitivity of many industrial mineral projects to specific inputs they require very careful analysis. The characteristics of the industrial minerals and the industrial minerals industry are reviewed and the significance of logistics, customer requirements, technology and marketing are discussed. Implications in relation to resources/reserves terminology are considered with phosphate rock used as an example. It is concluded that industrial mineral projects as a consequence of technology and market dependence in particular can give a high level of investment risk. The industry, however, offers most interesting and challenging employment opportunities for geologists, mineral engineers and economists.

Jan 1, 1988

Development and Validation of Ore Characterisation Test and its Use in Variability Campaigns of Comminution Circuits Impact testing was developed by assessing the fragmentation characteristics of ore samples after controlled impact. Standard methods are, however, limited to relatively large and coarse samples, which thus precludes their use in early stages of projects, as well as where only drill cores are available. The method described in this paper is based on the same concepts of controlled ore breakage, but using relatively smaller samples. It is particularly useful in assessing the variability of ore characteristics in early stages of greenfield projects, as well as in predicting the performance of existing grinding circuits. A validation program was carried out in which a good adherence to the original test results was obtained. The results were used for (a) simulation of a copper comminution circuit as a function of the ore characteristics, and (b) evaluation of sampling protocols used for assessing fragmentation characteristics.

Sep 13, 2010

Three large deposits of good quality lignite were located and delineated in the Central Otago region between October 1978 and July 1979. The program was initiated and funded by Mines Division of the Ministry of Energy as part of the national Coal Resource Survey. The exploration work was carried out by Lime and Marble Limited on a contract basis (Bowman, 1980). The three deposits were all potentially mineable by open cast methods and possessed combined indicated and, inferred reserves in the order of 1000 x 106 tonnes. They ranked with the previously discovered Eastern Southland 1ignites and as such constituted an important national energy resource. Fifteen months later a second more detailed investigation of similar duration was undertaken by the Liquid Fuels Trust Board (LFTB). The objective was to upgrade and refine the geological data base of all of the nine South Island 1ignite deposits in order to make preliminary economic assessments of their potential. Again Lime and Marble Limited acted as the exploration operator (Bowman, 1981a, 1981b, 1981c).

Jan 1, 1983

By D A. Manhire, R M. Flores

The commercial develop of coalbed methane from the Powder River Basin has demonstrated that low-rank coals can be a viable source of gas. Currently over 20 000 coalbed methane wells exist in the Powder River and it is predicted that there will be 50 000 wells by 2010. What makes the Powder River Basin successful is the thickness of the coal (in excess of 30m) as well as the low ash content (

Jan 1, 2002

The mercury, gold, silver, copper, lead and zinc values of soils over altered and mineralised rock were determined to establish the potential use of mercury as an indicator element in geochemical prospecting. The results are presented to show that mercury can be used successfully in prospecting for precious metal mineralization in the Thames-Waihi area.

Jan 1, 1979

Application of Natural Zeolite for the Removal of Diethylenetriamine (DETA) and DETA-Metal Complexes from Flotation Process Water

Sep 13, 2010

Effects of Hydrated Mg2+ on KCl Flotation

Sep 13, 2010

Experimental Study of Ore Characterisation Methods for AG/SAG Mills Mining companies have long recognised the importance of ore breakage characterisation in design and optimisation of their crushing and grinding circuits. In one of the industry standard methods relevant to AG/SAG milling, ore is characterised using mainly high energy single impact tests. However recent DEM studies have suggested that breakage in AG/SAG mills is mainly due to low energy repetitive (or multiple) collisions rather than single high energy impacts. Hence a study was initiated at the JKMRC to investigate the behaviour of ores under such conditions. Carefully designed experiments have been performed using two laboratory mill sizes (0.6 m and 1.1 m diameter) to mimic the reported low energy repetitive impact breakage under low load conditions. The breakage characterisation parameters derived from standard high energy single impact tests on the same ores was then used to predict the low energy repetitive impact breakage. Significant bias was found in the simulations which clearly warranted further investigation. The extensive experimental program which followed employed three separate methods: the JKRBT (JK Rotary Breakage Tester) for high energy single impact and low energy repetitive impacts, gravity drops for low energy repetitive impacts, and laboratory mills to provide an extended number of low energy repetitive impacts. The breakage energies associated with these experiments were accurately measured with a high speed video camera. Two breakage indices, the degree of breakage (t10) and the breakage probability (S) were used to describe the breakage test results. This paper summarises the major results from this experimental study, which has facilitated the development of a new breakage characterization method relevant to AG/SAG mill modelling.

Sep 13, 2010

With the launch of Immersive Technologies' next generation of Advanced Equipment Simulators for the mining industry, correlating and influencing safety, productivity and maintenance with operator competency improvements is now made even more effective. In early 2008, Immersive assembled a project team to investigate the potential linkages between operator competency and performance. Advanced Equipment Simulator Users with a range of sophistication were interviewed and consulted. The result was new and enhanced 'value realisation' programs to directly assist mine sites to deliver the expected return on investment (ROI) from simulators and operator competency development. In just over one year, 29 mine sites around the world have benefited from 34 completed programs. Case studies have been compiled to demonstrate the impact of the implementation of this approach, including at the following operations: Anglo Coal - Callide (Australia), Freeport McMoRAN - Grasburg (Indonesia), Equinox Minerals - Lumwana (Zambia), Peabody Energy - Cabllo (USA), and Xstrata - Lomas Bayas (Chile). Significant performance improvements have been achieved including: reductions of 47 per cent in gear shifting and 37 per cent in over speed errors, improvements of 68 per cent in park break errors and 12 per cent in spotting time, and increase of 54 per cent in passing emergency fire handling competency tests. This presentation draws on these case studies to clearly demonstrate the linkage between improved operator competency through the implementation of training programs tailored around Advanced Equipment Simulators and production performace measured by a range of standard metrics at mines around the world.

May 1, 2010

To ensure that its voice is heard in the development of policies and plans under the Resource Management Act, the mining industry is challenged to participate in their preparation. This paper outlines a number of practical ways in which the industry can participate in debate on sustainable management and how it can be put into practice within the industry.

Jan 1, 1992

Jan 1, 2004

Grinding and Flowing Investigation on Dry Stirred Ball Milling in Order to Determine the Influence of Grinding Aids Huge difficulties of the great ultra fine ground material production in dry stirred ball mill are the cohesion and agglomeration of the particles. During grinding the material stick on the grinding wall and the grinding media furthermore the grinds start cohere, making aggregation and agglomeration to appear. Due to these effects the particle size will not decrease after a certain value during grinding and the energy demand increases significantly. According to experience on fine grinding in ball mill, it is well known that these effects can be reduced with the use of grinding aids. The influence of grinding aids has three different effects: due to the adsorption strength reduction (Rebinder effect) the grinding resistance of the material decreases; the surface energy diminishes and the agglomeration liability decreases; and the flow properties of material improve. The aim of this study is to investigate the flow properties of fine grinds and the effect of grinding aids on flow properties in case of dry stirred ball milling. In addition, the influence of grinding aids was investigated based on the particle size distribution and specific surface area of grinds and the specific energy demand of grinding. The examinations were carried out with three different model materials (limestone, clinker, quartz) using the usually applied grinding aid. The flow properties were measured by the Jenike shear cell; the particle size distribution and specific surface area were measured by laser particle size analyser (Fritsch Analysette 22), grinding energy demand was measured with microcomputer controlled digital energy meter. It can be said that under certain measuring circumstances the influence of grinding aid on flow properties can be demonstrated by Jenike shear cell, so the grinding result is in correlation with the flow properties of grind.

Sep 13, 2010

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

By W E. Vance, B H. Ashton

The emission of seam gases into underground workings in coal mines is acknowledged as a major hazard, particularly methane due to its possible ignition. Acknowledge of seam gas parameters is important for the prediction of gas emission rates into the ventilating air current. They are also important as the basis for the evaluation of the likely contained gas as a possible energy source.   Gas content determinations for the Kupakupa seam have been made at the Huntly West Mine.  Applying the method of Creedy (1986) to face samples, gas contents of 1.80 and 1.66 have been determined. Using desorbed and residual gas content data a content of 1.92 m3/t has been derived. These are on an ash included basis. Calculations using the adsorption equation of Kim (1977) and coal quality have given a gas content of 2.19 m3 t. Long-hole exploration drilling at Huntly West Mine has provided information on gas pressure. A pressure rise test has given a reading of 500 kPa (absolute); this is low compared with the pressure given for the determined gas content from theoretical adsorption isotherms.

Jan 1, 1991