Search Documents

By OÆBrien D. R

Up until June 1988, Mount Thorley Coal Handling and Preparation Plant disposed of tailings by two methods. Approximately half of the plant tailings was mechanically dewatered by solid bowl centrifuges mixed with plant reject and was subsequently disposed in mine overburden spoils; the remainder was pumped to tailings ponds. Both future mine planning and environmental constraints could not allow for the long term construction of more tailings ponds so, following evaluation of available dewatering technology, belt press filters were selected for the treatment of tailings in excess of the capacity of the existing solid bowl centrifuges. Commission of the four 2.5 metre wide belt press filters soon showed that marked differences in performance were experienced when treating different coal seams. Further analysis showed that the coal tailings from different seams were quite different in terms of clay mineralogy, and these differences could be correlated with varying degrees of filter performance. Poor filter performance was experienced with coal tailings rich in sodium montmorillinite clays. A number of variables were investigated including in-line mechanical mixing of flocculant and feed slurry, cation exchange reagents such as gypsum, and upstream addition of cationic flocculant. In order to achieve satisfactory performance on the worst tailings, a combination of all of the above was required. In this paper, the reasons for selection of belt press filters and the program of investigations and testwork required to arrive at satisfactory belt press filter performance for the treatment of troublesome bentonitic rich tailings are discussed.

Jan 1, 1989

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

By Stanton G

The Department of Mapping and Surveying (DMS), the Australian Key Centre in Land Information Studies (AKCLIS), the Department of Industry Development (DID) and the State Government Computer Centre (SGCC) are testing a regional information network in northern Queensland. Several study sites have been chosen by different groups of participants. The members of each common-interest group share their data for the site. They can also access datasets supplied by other organisations that are not directly involved in the particular study being undertaken. The participants include state government departments, local authorities, fed- eral organisations and the private sector. The participants communicate with computer systems in Brisbane via Q-Net. Q-Net is a pilot State government tele- communications network, established by the Department of Industry Development. Q-Net uses the communications sat- ellite AUSSAT 1 as the primary instrument of data transfer. The Q-Net network is a star system, with a Master Earth Station in Brisbane acting as a hub for radial earth stations, located throughout Queensland.

Jan 1, 1987

The overall systems approach to blast furnace aerodynamics is explored including the time and spatial inter-relationships that exist between the furnace lines, tuyeres, burden characteristics, distributor capabilities and furnace operating practice. Attention is called to the time dependent, three dimensional aspects of blast furnace aerodynamics and to the existence of several zones within a furnace where the flow characteristics are different. Changes in furnace operating practice to take further advantage of fully beneficiated burdens including formed coke are discussed from a practical viewpoint. Lessons learned in a variety of shaft furnaces used for other purposes are discussed insofar as they have a bearing on aerodynamics in an iron blast furnace. Questions are raised about the penetration of hot blast in large furnaces. Operating practices and.proposed solutions are evaluated where tuyeres over iron and slag notches are restricted or plugged. Opportunities are presented for using on-line hierarchical computer systems with adaptive tuning algorithms to provide non-linear control of changing process conditions in real time. This will make it possible for the blast furnace operator to optimise a variety of interrelated paramaters, each with different response times. Potential increases in productivity, fuel savings and improved quality control are believed to be within reach.

Jan 1, 1975

Welcome to Mount Isa- my home city and without doubtthe base for what promises to be the most exciting mineral development yet seen in Australia.Mr. Chairman, it also gives me great pride to representthis area in the Queensland State Parliament as well as being the Minister for Minerals and Energy in the Queensland Government.Mount Isa is now part of the Australian mining industry folklore.It is all what a good mine is all about. It is. all what a good community is all about.

Jan 1, 1993

By Lyman G. J

The volumetric distribution of valuable mineral, or phase, within a set of particles is called the liberation distribution. To optimise a mineral processing plant it is necessary to know the liberation distribution in most of the streams, especially those adjacent to separation devices. Possibly the most common method of analysing ore particles is to section sets of similarly-sized particles. However, the observed sections can appear liberated even if the particle is composite. This means that the 'apparent' liberation distribution can be very different to the 'actual' liberation distribution. This discrepancy is called stereological error. One must then somehow estimate the actual liberation distribution using the apparent liberation distribution. This problem is called the liberation distribution problem and its solution is the subject of this paper. The solution is based on a sorting algorithm which uses geometric probability equations. These equations are based on the assumption that sectioning is isotropic and uniform. Apart from these assumptions the equations are completely independent of particle shape or texture. The algorithm is verified by numerical simulation and experimental methods. For the numerical simulations the correspondence between the actual and estimated liberation distributions is excellent. For the experimental methods, the agreement is not as good and appears to be due to experimental errors.

Jan 1, 1995

By Wooller R

The 3-D regular block model used for long term mine planning at Hamersley Iron did not fulfil the requirements for short term mine planning in terms of accurate representation of geological structures, contacts and boundaries in the orebodies. A computer model, based on zone plans, is being created as a single orebody model for all phases of mine planning. The zone plan is the primary interface between the geologists and mining engineers. It is essentially a bench plan at mid-bench height showing geological structure, material type boundaries, the grade and physical characteristics of ore blocks. The method allows for the dilution of ore zones by waste material. The stratiform nature of the orebodies allows zones of varying grade to be readily delineated on the plans. The Zone Plan Model (ZPM) is the interface between geological and mine planning computer systems. It is the basis of all mine planning with applications including long and short term mine plans, reconciliations, general ore reserve estimations, pit design and general model enquiries. The system was designed to be user driven. The user has complete control at all times as all computer generated data are fed back to the user who may then elect to override the computer. Various controls were built into the system to ensure model validity and integrity. The system has proved to be invaluable as a tool for users with little or no computing experience.

Jan 1, 1986

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

By Yaniuk DW

The sampling of non-ferrous concentrates from trucks and trains has long been carried out either manually or by automatic spears. Very little use has been made of conventional sampling systems for sampling concentrates at transfer points, or cross-belt samplers for sampling from the belt as the concentrate moves along the conveyor.Due to the high value of base metal concentrates and the often extremely heterogeneous nature of the material it is imperative that the sampling procedures adopted are accurate and precise. The basic principle that all particles in the stream have an equal opportunity to be included in the final sample is not fulfilled by accepted traditional concentrate sampling procedures such as the spearing of wagons, trucks or streams. This may lead to significant bias being introduced into the final sample.Consequently, the application of correct sampling procedures, either with conventional cross-stream samplers or the newer cross-belt samplers, is of prime importance.SGS Australia has recently installed a number of cross-belt samplers for the sampling of base metal concentrates both in Australia and overseas. The application of these samplers will be discussed with emphasis on the benefits of their use.

Jan 1, 1976

By McNabb KE, Ward B, Dyer G

Roof conditions at Southern Colliery, the second longwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 in thick roof beam either bonded or detached, with either a 2 in or 5 in overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992

Comminution Kinetics equations are developed to take into account difference of grindability of mineral components. The equations describing both batch and closed circuit grinding or crushing processes are given. These equations are applied to industrial data to derive comminution kinetic and classification characteristics of the component minerals in a multi-mineral ore. Control strategy based on these concepts is presented.

Jan 1, 1985

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu's Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

By P Dare-Bryan

Many mines have an interest in improving fragmentation at their sublevel caving operations in order to produce better ore recovery, lower dilution and less overbreak. The primary requirement for the extraction phase is to understand and optimise the flow of the fragmented rock in the rings including interactions with the caved material. Rock fragment formation is critically controlled by the blasting phase and can potentially be improved by optimising the dynamic energy distribution throughout the ring through the crafting of explosive charging, priming position and initiation timing. The modelling of fragmentation and damage due to explosive loading of complete rings is inherently and irrevocably a three dimensional problem that is difficult to address. We have therefore initially utilised an analytical code to predict vector peak particle velocities and energies that are restricted to the plane of a ring. Dynamic energy distributions based on common timing and priming practice have been compared with other possibilities using conventional pyrotechnic detonators as well as initiation designs based on accurate electronic detonators. The energy distribution can be quite subtly tailored to increase energy in appropriate regions or to decrease energy in the brow region for example to potentially reduce instability and the probability of misfires. We have also recently developed the capability to efficiently model particle flow using four-sided polygonal elements. Despite the 2D limitations of such a model this results in more realistic fragment interaction and stacking than can be achieved using conventional rigid circular elements. Modelling of a typical sublevel caving ring utilising these elements activated by the correct dynamics offers considerable potential for understanding the influence of the blasting energetics and timing on the complex flow and extraction process.

Jan 1, 2005

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By Restarick C. J & Stewart P S B, Kelsall D. P

Over a four-hour period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had sane reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one third of the lead losses in the final tails.

Jan 1, 1980

Alcoa of Australia's Del Park mining op eration is centred 9 km. east of the Pinjarra alumina refinery, and is centrally locatedwith- in the 10, 000 sq. km. lease which the Company holds for bauxite in the Darling Ranges. An- other mining operation is situated near the township of Jarrahdale, and supplies bauxite to the Kwinana refinery. Definition of the bauxite ore, development works and mining to the ore haulage stage, are identical for both mining operations. Exper- ience, and production cost figures, obtained from the Jarrahdale mine, where 100 tonne trucks are used to haul ore to a fixed crushing plant, led to the development of the Del Park mining concept with increased mobility of op- erations. The crushing-conveying-stockpiling arrangement at Del Park consists of a 1200 t. p. h. mobile crusher feeding bauxite to an overland conveyor system which transports the ore approximately 6. 66 km. to the stockpile area in the refinery. In the refinery raw mat- erials area the bauxite is distributed into 200, 000 tonne stockpiles by means of a travel- ling boom stacker.

Jan 1, 1973

By Thomas G. A

THE irregularity of the Mount Morgan (Queensland) ore body presents problems other than those only of mining. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and fromhighly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from many stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore, yet it is never safe to take this for granted, and constant assaying is necessary. At the same time the ore merges from one class into...

Jan 1, 1911

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

An ongoing research program into surface subsidence over Room and Pillar coal mining is described. A subsidence monitoring network has been established for one Room and Pillar mine in the West Moreton Coal Field of South East Queensland, at which pillar extraction is being conducted. The maximum measured subsidence to 28 January 1986 was 638 mm, with movement continuing. Analysis of the monitoring data with view to application of the subsidence pre- diction theory developed by Kowalczyk (1972) is discussed. The Kowalczyk theory provides predictions of subsidence depression, slope of surface, horizontal displacement, surface curvature and horizontal strain, for both the Partial and Total Settlement cases. The development of subsidence with time is also investigated and a preliminary analysis conducted.

Jan 1, 1986