Search Documents

By D Brown, Z Tabor

Projects must be flexible to account for the rapid development of new technologies and changing stakeholder expectations. Coupled with calls for bleeding-edge solutions, customers, shareholders, and regulators demand robust, safe products and systems-of-systems. Developing and integrating these solutions is becoming increasingly complex and maintaining the flexibility required to ‘pivot’ to effective solutions can be a serious challenge. The necessary flexibility is fundamental to the Agile ethos, and this family of methodologies therefore offers a potential solution to this challenge (Beedle et al, 2001). These have traditionally been delivered with systems engineering applied through a Waterfall methodology. Agile Systems Engineering combines both approaches and presents a means to achieve these goals without compromising flexibility, quality or safety. A robust methodology for the application of Agile Systems Engineering is required to enhance practical outcomes and reduce risk for real-world mining projects.

Sep 1, 2024

By D Engelhardt, G Lane

The Cadia mine has shifted from an open pit operation to the Cadia East underground panel cave. The resulting increase in milled tonnes, more competent ore and the decrease in fines production through shifting to panel caving were predicted to require an increase of over 25 per cent in installed power. This expansion was accomplished via the installation of secondary and high pressure grinding rolls (HPGR) crushing of the ore, with the semi-autogenous grinding (SAG) mill receiving a combination of primary, secondary and HPGR crushed feed. This design, criteria and rationale for selection was presented at the SAG Conference 2011. This paper reports on the initial impact of secondary and HPGR crushing on the circuit performance with the new panel cave feed.CITATION:Engelhardt, D, Lane, G and Powell, M S, 2014. Cadia expansion – the impact of installing high pressure grinding rolls prior to a semi-autogenous grinding mill, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 233–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

The Taupo Volcanic Zone in New Zealand and the Philippine Mobile Belt in the Philippines are characterized by active subduction, active volcanism and high seismicity. The main factors affecting characteristics of geothermal systems in both countries are: tectonic setting, source magmas, maturity of the systems, and depth to the degassing magma body. Within New Zealand, geothermal systems are grouped into arc- and rift-type. Fluids in arc-type systems contain high amounts of volatiles (40%) and higher Cl contents (3,000-10,000 mg/kg). Maximum temperatures are also higher, reaching up to >400¦C. Arc-type alteration assemblages in New Zealand and the Philippines are similar. Because Philippine geothermal systems are less mature, have higher temperatures and steeper geochemical gradients than New Zealand ones, advanced argillization is more widespread occurring down to depths of 2000 m. Mineral phases are more varied due to the active input of magmatic waters and the formation of vapor conditions at depth, forming P04-, B-, Li-, Ce-, F-, and Cl-bearing minerals at high temperatures. In the Philippines, high temperature magmatic-hydrothermal to contact metamorphic assemblages containing biotite, amphiboles and pyroxenes are relatively common, but rare in New Zealand.

Jan 1, 1995

A new engine family has been developed by Caterpillar Tractor Co. for application in off-highway trucks. This family, the 3500 Series is available in three configurations, covering a 600-1200 kilowatt range. This engine series incorporates the latest in design technology, stringent functional specifications for servicing ease, fuel economy, reliability, optimum performance and parts interchangeability. TECHNICAL INTRODUCTION The 3500 Series Engine has been under development by Caterpillar for over eight years and has undergone extensive testing in the laboratory and in field prototype units. - The engine configuration is a 600 Vee in 8, 12, and 16 cylinder versions. - The intermittent power output per cylinder is 75 kilowatt (100 HP). Net power for off-highway trucks is 600-1200 kilowatt (800-1600 Hp) depending on engine configurations. The 3512 (3500 Series Engine 12 cylinder Vee configuration) was the first model of the 3500 Series released. These engines offer optimum user value in terms of product durability, reliability, fuel consumption, performance and installation flexibility. Additional features of 3500

Jan 1, 1982

By C Dick

Over the past three decades, mining operations have seen a significant increase in the use of contractors for mining, camp management and catering, recruitment, maintenance, power management, and commissioning. More recently contractors have been engaged for stores and logistics, OH&S, environmental, exploration, training etc. In some countries, such as South Africa, the trend is towards total outsourcing of all aspects of a mining operation which is coordinated by the owners’ management team.During the Global Financial Crisis (GFC) more Australian companies considered and/or took on this approach to recruiting for both projects and operations as mining companies were forced to rethink their corporate strategies as commodity prices plummeted to low levels, pushing operations and projects into potentially financially unviable territory.This paper discusses the labour recruitment, commissioning and operating strategy of Western Areas NL (WSA), with the assistance of Independent Metallurgical Operations Pty Ltd (IMO), as it progressed construction, commissioning and operation of the Cosmic Boy nickel concentrator at the Forrestania Nickel Project during and post GFC. The use of IMO contractors allowed Western Areas to mitigate labour cost risk during the uncertainty caused by the GFC and let their management team focus on the task of bringing a new operation into viable and profitable production.

Aug 8, 2011

By J Holdsworth, L Sutton, A Lavrinec, D Ilic

Air quality is a big topic of discussion in regional mining communities as well as urban environments situated close to port terminals handling bulk solids. Community perception of poor air quality can significantly affect the reputation of the mining operation and handling facilities. Dust monitoring for regulatory compliance relies on using a handful of accurate but very expensive sensors, usually situated at the boundary, relatively far from the activities that generate the airborne dust. These reference monitors measure dust leaving the site but dust mitigation and management on-site largely relies on operator judgement. At a fraction of the cost, small wireless solar powered units can be used to supplement reference monitors in real-time. Due to their compact nature, portability and low price, these units can be implemented on a mass scale to increase spatial resolution of dust measurements and, more importantly, in much closer proximity to both the dust generating activity and the sources of dust. This can provide valuable insights into the origins and timing of dust generation thus producing datadriven decision-making while minimising subjectivity. Similarly, light detection and ranging (LiDAR) is another supplemental technology that can be used to increase the spatial resolution of dust measurements in near real-time, however, the cost of commercial systems even exceeds that of regulatory monitors. LiDAR also presents difficulties in quantifying dust plume concentrations. This study presents learnings of implementing both technologies for dust emissions management. Several low-cost sensor units and a fast-scanning custom-built 3D LiDAR system operating at a range of 1.5 km with a resolution of 1.5 m were deployed on a surface mine to monitor dust emissions from different activities. The project explores the use of real-time sensor data to quantify LiDAR measurements in parallel with integration into mine planning. The approach can assist in prioritising dust mitigation activities thereby reducing instances of emissions exceedance and minimising water use through databased and targeted application. Demonstrated is an opportunity for a step-change in industry best practice as well as commercialisation and operationalisation of the method across different industries, including future mineral extraction.

Sep 18, 2023

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Battison, R Duggan, S Esen, K Henley, P Dare-Bryan

Increased catch bench crest loss has been observed in recent years at Barrick’s Cowal Gold Mine situated in central New South Wales, Australia. A project was initiated to diagnose the cause of the crest loss, and evaluate ways to limit its effect on final walls.A range of different blast measurement techniques were utilised to evaluate the progressive damage caused to catch berms by presplit, production and trim blasts. Techniques employed included; single point vibration measurement, cross-hole seismic analysis, precision berm surveys, horizontal p-wave velocity measurements, crest loss volume calculation and water level changes between blasts.Blast measurements showed that the majority of damage to the catch berm was caused by the presplit blasts, which registered vibrations greater than 700 mm/s at 5 m behind the presplit line. As a result, considerable changes were made to the blast designs after a series of computer simulations via mechanistic blast modelling (MBM). The uncharged presplit collar was increased from 2 m to 4 m, and every second hole was left uncharged. Vibration modelling using a multiple seed wave (MSW) model was used to optimise trim blast delay timing. Burden relief was changed from 16 ms/m to 27 ms/m using one hole firing per 4 ms time window, and the initiation angle was changed from shallow to steep. These changes in the presplit loading and trim timing helped reduce catch bench crest loss by 1–2 m.Trim shots using a high strength bulk emulsion explosive were also identified as contributors to berm damage after analysis of blast monitoring and MBM modelling. The modelling study resulted in the generation of alternative blast designs to minimise the crest loss, including the use of low-density/low-velocity of detonation (VOD) bulk explosive product (Flexigel™ Advantage) in trim pattern designs. This was trialled on the Northern and Eastern pit walls to evaluate the damage to catch berms on final walls. The trials demonstrated that berm vibration was reduced significantly; fragmentation was similar (or slightly blockier) compared to the fragmentation using the old blast designs; displacement of the berm was reduced, so increased catch bench widths were attained. This paper summarises the trials, and presents a summary of the crest loss to date.CITATION:Battison, R, Esen, S, Duggan, R, Henley, K and Dare-Bryan, P, 2015. Reducing crest loss at Barrick Cowal Gold Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 189–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

During the later part of 2007 I was lucky enough to visit the Atlas Copco facilities in Sweden, and to see first hand what a large and diverse company Atlas Copco is. The reason this paper calls the Atlas Copco experience a bonanza is that it means a source of great and sudden wealth or luck; a spectacular windfall or a rich mass of ore, as found in mining. I think this aptly describes the scholarship as it has greatly increased my wealth of knowledge of the mining industry. This paper intends to encourage all those eligible to apply for this fantastic scholarship opportunity, and seeks to thank all those involved who made this scholarship the amazing experience that it was. Atlas Copco produces most of its Swedish products in the town of +rebro, and it was here that I spent most of my time, visiting the Underground Rock Excavation group, the Surface Mining Equipment group and Rocktec. I also travelled around Sweden and was able to visit one of OricaÆs manufacturing plants, the Secoroc groupÆs manufacturing plant, the Geotechnical Drilling and Exploration group as well as being fortunate enough to visit the LKAB mine in the Arctic Circle in Sweden. The trip was not all information on Atlas Copco products and services however; I was able to go to the Ice Hotel in JukkasjSrvi and drink Absolut Vodka out of ice glasses, go on a reindeer safari (as well as eat them!), sample the fine meat from a moose, drink local schnapps, attend the Atlas Copco Christmas party, wander around the wonderful city of Stockholm and generally immerse myself in the great Swedish culture.

Jan 1, 2008

By H Kurth, L Balzan

On-belt analysers have been used since the early 1980s in the coal sector to measure ash content in real time for diverting material on conveyors to remove waste, bypass beneficiation and allow suitable material to proceed to the wash plant for processing. Since 2008, a GEOSCAN-M elemental analyser has been used on an overland conveyor in South Africa to divert direct-shipping quality iron ore to bypass a jig plant. This paper focusses on recent evaluation work to determine the suitability of an on-belt analyser to upgrade the processing plant feed in a copper-gold operation.Copper-gold ore samples from New Gold’s New Afton Mine near Kamloops, BC, Canada were tested to assess measurement accuracy over short time increments. A two-minute measurement increment has been used in the minerals sector as a compromise between good measurement accuracy and a useful tonnage (haul truck equivalent size or smaller). At New Afton, this increment represents approximately 35 t of material. Segregation decisions are currently made after visual and sometimes analytical determination, at increments of approximately 500 t to designate material as ore or waste at the drawbell in the cave.Results of test work including the composition range and expected accuracies by element are shown. The operation, which is not mine constrained, was evaluating the potential for ore upgrading through waste and low grade increment diversion to upgrade ore quality feeding the mill. Prompt-gamma neutron activation analysis (PGNAA) was considered as the company recognised that it would measure through the full conveyed cross section continuously and produce multi-elemental measurements unaffected by particle size, dust, moisture content, layering and segregation, mineralogy and belt speed.GEOSCAN analyses over various analysis periods will be collected to identify variability in the conveyed material quality and used to generate tonnage-grade curves so that an optimal diversion (bulk sorting) tonnage increment can be determined. Measurement increment time can be customised to suit site requirements. CITATION:Kurth, H and Balzan, L, 2017. Assessing bulk sorting suitability at the New Afton mine, in Proceedings MetPlant 2017, pp 315–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By B Reynolds

The process design for green- or brown-fields metallurgical plants typically starts with two fundamental elements: the detailed mass and energy balance and the plant flow availability. The detailed mass and energy balance is generally developed using process flow-sheet simulation software and represents the steady-state operation of the plant at normal operating conditions. The plant flow availability, also known as a range of other industry-specific terms such as ‘flow availability’ and ‘operating factor’, describes the ratio of plant production to the steady-state mass balance. These elements are then used together as the basis for equipment selection and design.Plant flow availability takes into account a myriad of production loss factors including planned and breakdown maintenance, feed availability and composition changes, variability in operational performance and the interaction of batch and continuous unit operations. The combined impact of these loss factors are complex and as such plant flow availability is usually derived using a top-down approach such as comparison to an existing operation, a group of similar operations or to an anecdotal ‘industry leading’ benchmark. These top-down approaches are fraught with risk however, as they cannot factor in changes to equipment selection, flow-sheet or plant operating philosophy, and can result in over-expenditure of scarce capital or shortfalls in plant production.The use of dynamic simulation to provide a bottom-up alternative to quantifying the plant flow availability in metallurgical plant design has been growing rapidly in recent years. It provides a technique to quantify the combined impact of the loss factors described here and a tool to support process design and equipment selection by facilitating a range of sensitivity and what-if analyses. This paper presents a case study of how dynamic simulation has recently been used to support the

Aug 8, 2011

By F Weir, B Estrada

The impact of seismic loading on open pit slope stability in Australia is often only considered where the slopes are located adjacent to tailings facilities or other major infrastructure. The debate regarding application of seismic loading in open pit design in Australia is usually founded on limited reporting on significant damage of open pit operations during earthquakes, the common perception that earthquakes do not occur in Australia or that they are unlikely to occur during the mine life of the mine. It is frequently overlooked that pit slopes that have withstood strong earthquakes in highly active seismic regions are often designed under strict seismic guidelines. This paper discusses the factors that impact earthquake performance of open mine slopes. These factors include topography, slope geometry, rock material and mass properties, water management and intrinsic pit design. Further, the paper presents insights into the characteristics of earthquake activity in Australia such as magnitude distribution, earthquake depths, areas prone of earthquake activity and general seismic hazard that are relevant to pit design. Guidelines are provided on the conditions and circumstances under which earthquake design in open pit mining should be considered. In addition, this paper provides recommendation on the applicable methods for assessment of the impacts of earthquake loading on pit slope stability.

Jun 22, 2022

By M Flis

The Razorback Iron Ore Project is a high tonnage, low-grade magnetite deposit that defines a new iron ore district in South Australia. Known since the 1960s, the deposit has come into its own as the iron hungry world demands not only larger tonnages, but higher grade and cleaner magnetite concentrate ores that counterbalance the increasingly dirty haematite ores that are coming into production.Razorback is hosted by the Neoproterozoic Braemar Iron Formation, a tillitic unit that is part of the Adelaidean Geosyncline sedimentary sequence. At Razorback, this formation forms the southern limb of the Pualco Syncline, dipping at 42° to the north and outcropping along a prominent ridge. The formation consists of a series of alternating bedded tillitic and interbedded magnetite units that represent cycles of glacial advances and retreats. Seven cycles, resulting in seven stratigraphic members, are recognised. Members B, D, and G are the thickest, at 30 - 70 m each, and are the target of current investigations. While the bedded magnetite has the highest iron content, typically 35 per cent Fe, the tillitic unit, at typically 26 per cent Fe, has similar iron content in the ground mass but is diluted by the inclusion of iron-poor granite and metasedimentary dropstones. The mineralisation forms a simple dipping tabular body with only minor faulting, folding and intrusives. Grades, thickness, dip, and outcropping geometry remain very consistent over kilometres of strike, presenting an excellent mining proposition.Razorback differentiates itself from other Australian magnetite projects in a number of important ways. It is not a banded iron formation (BIF); it will have low crushing and grinding costs; and it is located in an infrastructure-rich area close to open-access, high capacity rail, to a selection of ports and to gas, electricity, labour and engineering services. Royal Resources has announced an Inferred resource of 277 Mt @ 25.9 per cent Fe. The company is targeting a resource of 500 - 1000 Mt to support a 10 Mt per year concentrate production. Davis Tube Recovery work shows that the ore is capable of producing a concentrate of over 68 per cent Fe with very low deleterious elements. Metallurgical testing confi rms the ore is soft, and with near-zero initial stripping ratio the project will have a low opex. With access to existing critical infrastructure, capex will also be low, ensuring Razorback will be a highly competitive iron producer in this emergent mining district.

Jul 11, 2011

By B Vietnieks, N Widmer, L White, E Tata, J Natukunda, D C. Ilouga, J P. Tyler

The Republic of Uganda aims to exploit its’ significant, un-developed iron ore resources to supply the required raw material for developing its’ iron and steel industry across all the stages of the supply chain. Large prospects of iron ore exists in Uganda in the eastern (Tororo) regions and southwestern (Kisoro-Kabale) regions of the country. The Kisoro-Kabale iron ore projects covers mineralisation in hematitic banded iron formation (itabirite) in the north-eastern Congo-Tanzania Craton; covering ten Iron ore prospects. The prospects include Kamena, Karukara, Nyamiringa, Kyanyamuzinda, Rugando, Katagata, Rwengongo, Kijuguta, Kihumuro and Katuna. High-grade hematite ore prospects in south-western Uganda have known grades ranging from 55 per cent to 68 per cent iron ore content with an exploration target estimated at over 500 million tonne (Mt). Small scale production of iron ore from the south-western regions provide raw material to existing steelmaking and direct reduction iron ore plants located in the Jinja and Iganga districts of eastern Uganda. Large quantities of iron ore and other steelmaking raw material, however, are required to be imported into Uganda due to the limited exploration and development of their own iron ore mining operations. A joint collaboration between the European Union (EU), the Department of the Geological Survey and Mines (DGSM), Ugandan Ministry of Mines in partnership with Australian drilling and mining consultancies, ADT Africa and Kalem Group as a EU funded project was undertaken during November 2022 and September 2023. Exploration and evaluation of the ten iron ore prospects in south-western Uganda was undertaken through geological mapping, drilling, assaying, and technical studies with the view to attract investment for the development of Uganda iron ore mining and steelmaking industry. The collaboration developed mineral exploration policy, guidelines and standards, an iron ore exploration manual, a geological data management policy, and to support the sustainable development of iron ore mining in Uganda through building the capacity of local Ugandan geology and mining personnel through the transfer of knowledge and expertise from experienced iron ore experts. The quantification of these resources is an important first step in assessing their economic potential and attracting mining investors. This paper presents an overview of the investigation program and the preliminary results as an important first step in attracting mining investors to this exciting new iron ore province.

Sep 18, 2023

By B Yeganeh, A Sam, A Kohsari

The base of separation at Gol-e-Gohar iron ore plant (Sirjan in the south of Iran) is magnetic separation after milling. Magnetic separation in the plant is divided into two parts: dry magnetic separation and wet magnetic separation. Sixty-five per cent of the plant production belongs to the dry magnetic separator section. Therefore, investigation of this part of the plant is necessary. Prediction of plant production is one of the most important subjects in mineral processing plants. That means, before feed enters the plant, specification of production has been calculated with laboratory methods. The purpose of this paper is the prediction concentrate quality has achieved from the dry magnetic separator. The content of iron in the final dry concentrate will be predicted, with laboratory, pilot and modelling methods, before feed enters the plant. Different variables are used in this approach, which consist of: speed of the first dry magnetic separator (rougher), speed of the third dry magnetic separator (cleaner), iron content in plant feed, size of 80 per cent passing of feed, size of 20 per cent passing of feed and iron content in pilot dry magnetic separation concentrate that performs in a standard manner. The artificial neural network is used for modelling and one of its branches is the radial basis network (RBN). Iron content in magnetic separating concentrate in plant will be introduced as the target and will be calculated with the RBN method. In the RBN method, a set of data enters to neural network and they will be trained and simulated. Finally, the target will be predicted. Ultimately, the original target (actual iron content) and the predicted target (predicted iron content) compare and error of them will be calculated. The obtained result is acceptable and satisfactory.

Jan 1, 2007

By D Symonds, S S. Kanchibotla, L Kennelly, G McNamara, J Gaunt, B Adiyansyah

Ban Houayxai is a gold-silver mine operated by Phu Bia Mining Limited in Laos since 2012. The first two years of operation processed predominately soft oxidised ore but subsequent years were expected to process more fresh hard ore. Fragmentation of the fresh primary ores was also expected to be much coarser than for the soft oxide ores. This coarser and harder ore is expected to significantly reduce mill throughput and mining productivity. The Ban Houayxai management realised the potential downside risk when processing fresh harder ores and implemented a blast optimisation project to deliver finer fresh ore to the mill without unduly increasing blast induced dilution and damage.JKTech and the Ban Houayxai drill and blast team began a joint blast optimisation project in April 2013 to achieve finer fragmentation from fresh ores. This was achieved by modifying the bench geometry, blast patterns and applying exceptionally high levels of quality control during implementation. Blast induced ore loss and dilution was controlled by adjusting the ore blocks for blast movement. Finer fragmentation from these modified designs improved mill throughput for the hard fresh ore by 46 per cent above design on average. These new practices have been embedded in site operating procedures and have provided a quick reference ‘cookbook’ document for the engineers.CITATION:Gaunt, J, Symonds, D, McNamara, G, Adiyansyah, B, Kennelly, L, Sellers, E J and Kanchibotla, S S, 2015. Optimisation of drill and blast for mill throughput improvement at Ban Houayxai Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

China has been producing gold for more than 4000 years with gold production increasing substantially since the 1980s, from about 25 tonnes in 1980 to some 160 tonnes in 1998. More than 80 per cent of the gold production is from East China. However, complete information on eastern China gold has been rarely reported internationally. This is a general overview on the tectonics and metallogeny of gold deposits in East China. The geology of these gold deposits is compiled mainly from data and information reported in China, and is also based on the authorÆs work in China from 1974 to 1986 and a recent visit to China.

Jan 1, 1999