Search Documents

By P Craig, A Crosky, H Ramandi, S Saydam, H Chen

Frequency of reports on premature failure of rock bolts and cable bolts have increased in past two decades. Such a failure threatens both the safety of underground mine workers and the economic viability of the operations. Herein, we report on analysis of rock bolts and cable bolts failed recently in three underground mines in Australia. Magnetic particle inspection (MPI) and scanning electron microscope (SEM) techniques were used to study the failed bolts. MPI showed a number of subcritical cracks on the surface of the bolts. The majority of the cracks in both cable bolts and rock bolts were initiated from the base of ribs (indentation) where the stress concentration was high. SEM examinations showed tearing topography surface (TTS) in all failed rock bolts and cable bolts. These indicated that the failure occurred through hydrogen assisted stress corrosion cracking (HISCC). The results of this study enhanced the understanding about the failure of rock bolts and cable bolts in underground mines. CITATION:Chen, H, Ramandi, H, Craig, P, Crosky, A and Saydam, S, 2018. Analysis of premature failure of rock bolts and cable bolts failed in underground coal mines, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 407–413 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By P K. Banerjee, S Kumar

Indian iron ores with less than 62 per cent Fe are currently unexploited, except for a few sectors which export them to foreign countries. It is anticipated that by 2012 the countryÆs domestic steel production is likely to rise to the tune of 60 million tonnes per annum. To meet this requirement, it is necessary to utilise not only the existing high-grade deposits but it is also necessary to look into exploiting the leftover iron ores of lower grades. Hence, reserves with Fe content 62 per cent and below (particularly the ores with In the present paper, an attempt has been made to beneficiate three different types of low-grade iron ores selected from three different parts (states) of the country. In the paper, alternative routes for beneficiation and effective utilisation have been tested using different techniques in the laboratory in an attempt to match their (Al2O3/SiO2) ratio after thorough characterisation and liberation studies. The paper also encompasses the geological formations, occurrences and distribution of Indian iron ores as well as highlighting the problems associated with the fines, possible metallurgical routes, and their market segregation from the perspective of end users.

Jan 1, 2007

By S Kakara, A Kamaraj, S S. Varanasi, B V. R Mandalika, M B. Shaik

The properties of top slags play a very important role in secondary steelmaking. Fluxes should be chosen based on the ladle furnace (LF) slag requirements like viscosity, melting temperature, sulfide capacity, etc. CaF2 and CaO-Al2O3-based synthetic slags are the most used fluxes in secondary steelmaking to improve slag fluidity and interfacial chemical reactions. CaF2 is obsolete due to fluorine pollution and CaO-Al2O3 based slags have 40–50 wt per cent Al2O3 and 30–40 per cent CaO which is not beneficial for desulfurisation. Yet another drawback is that LF slag disintegrates into fine powder during cooling due to phase transformation C2S (2CaO.SiO2). Hence, there is a need for the development of low melting fluxes with high CaO content and the capability to prevent slag disintegration. The current work studied the effect of 0–9 wt per cent B2O3 on physico-chemical properties and characterisation of LF slags. X-ray diffraction (XRD) analyses were carried out to identify mineralogical phases present in slag and Fourier-transform infrared spectroscopy (FT-IR) analysis was done to understand the changes in bonds of B2O3 added LF slag. The characteristic temperature of slag was determined by a hemispherical method using high-temperature microscopy. Empirical models were used to calculate viscosity, break temperature, and sulfide capacity. FactSage™, ver 8.2 (by GTT-Technologies) simulations were carried out to find the equilibrium phase fractions and percentage of liquid slag at different temperatures. New phases such as Ca11B2Si4O22 and Ca2B3O5 were formed in LF slag with B2O3 addition. Based on the results, 0.5–1.0 wt per cent B2O3 was found to be sufficient to prevent C2S-driven disintegration of LF slag. Also, the melting temperature and viscosity of LF slag were reduced by adding 3–8 wt per cent B2O3 due to the formation of BO3 planar triangular structure and low melting eutectics in slag. Liquid slag started forming at a temperature as low as 800°C when B2O3 is >6 wt per cent. It was found that the sulfide capacity, viscosity, and break temperature of the slag decreased with increasing wt per cent B2O3. Based on the analysis carried out, B2O3 can be a promising fluxing material in secondary steelmaking, for improving the desulfurisation kinetics and valourisation potential of LF slag.

Aug 21, 2024

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

By B P. Micke

Central Norseman Gold Corporation was established in 1935 and has been mining on the Norseman field in Western Australia since then. It is Australia’s longest continuously operating gold mining operation at nearly 80 years, although it has had its periodic challenges in the intervening years.Over the last 40 years, a series of open pit mines around the Dundas Goldfield have supplied lower cost mill feed to the Phoenix Mill at Norseman from time to time but this has largely come to an end for the foreseeable future. Now that underground ore sources are once again the principal mill feed, there are several challenges to be met for an ongoing profitable operation.During the last 20 years, there have been three different owners and this has affected the manner in which the operations were managed quite significantly. These differing approaches are contrasted and examined in some detail from both the operational and financial aspects.Planning of a downsized operation to ensure sustainable profitability in the future in a mining environment where there has rarely been more than two to four years of reserves ahead of the mill for planning purposes has been a significant challenge. Several of the options examined are described, including alternatives for future mine development.CITATION:Micke, B P, 2014. Managing the margin at Norseman, Western Australia – a case study, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 119–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A D. Pradana, D R. Pradana, Y H. Putra, Z Zulhan, T Hidayat

The high temperature processing of nickel laterite ore is currently dominated by the Rotary Kiln- Electric Furnace (RKEF) technology. The ratio of SiO2/MgO (S/M) in the ore is one of the critical parameters that determines the success of the RKEF process. Incompatible S/M ratios in the ore can cause aggressive chemical interaction between the slag and MgO refractory. The slag-refractory interaction at conditions relevant to nickel laterite ore smelting was investigated in the present study. Synthetic mixtures representing the slag compositions of nickel laterite ore smelting were prepared by mixing MgO, SiO2, Al2O3, CaO, Fe2O3, and Fe and heating the mixtures in steel containers at 1300°C under an argon atmosphere for 3 hrs. Pure MgO crucible were used as containment material in the melting process of the mixtures to represent the MgO refractory. The kinetics of the slagrefractory reaction were investigated using samples with selected initial S/M ratios of 2.0 and 3.0 (wt/wt) (with constant CaO = 3 wt per cent, Al2O3 = 5 wt per cent, FeO = 10 wt per cent) by performing melting at 1500°C in MgO crucibles for 5, 30, and 120 mins under an argon atmosphere. The effect of the S/M ratio in slag on the slag-refractory interaction was also investigated by performing melting of mixtures with different initial S/M ratios of 1.75, 2.0, 2.5, and 3.0 (wt/wt) in MgO crucibles at 1500°C for 120 mins under an argon atmosphere. After the melting process, each sample was quenched in water, mounted in resin, ground, polished, and coated. The interaction between the slags and MgO refractory was then evaluated by analysing the polished samples using a scanning electron microscope equipped with an energy dispersive spectroscopy (SEM-EDS). Thermodynamic simulations using FactSage™ 8.0 thermochemical software were performed based on the experimental slag compositions, refractory, and conditions to support the evaluation process. The results show that a higher S/M ratio in slag leads to a higher tendency for the refractory component to dissolve into the slag. A higher S/M ratio in slag also leads to an increasing extent of solid-state diffusion of iron oxide into the remaining refractory grains. The dissolution of MgO into the slag is rapid; the MgO concentration in the final slag increased by 2.4 wt per cent and 5.7 wt per cent at initial S/M ratios of 2.0 and 3.0 wt/wt, respectively, within 5 and 30 mins of the melting process.

Aug 21, 2024

By R McDonough

DTL2 contract C916 was awarded in March 2009 for S$340 M. This contract includes two mass rapid transit (MRT) 1100?m long bored tunnels using two slurry tunnel boring machines (TBMs), with an internal diameter of 5.8?m, two cross passages and 135?m of cut-and-cover tunnels The contract also includes the design and construction of a new underground station including station entrances, subway links, architectural finishes and external landscaping. The station, located at Upper Bukit Timah Road near Jalan Jurong Kechil will also double as a civil defence shelter.The works included significant traffic management in a dense urban area in order to create the working areas whilst keeping the requisite number of traffic lanes. This involved numerous utility diversions and included the removal of a 33-year-old pedestrian overhead bridge (POB) over busy Bukit Timah Road. The station and tunnelling works were completed on time, including a ‘dock and dismantle’ TBM retrieval and subsequent breakthrough of the separating wall.This paper will detail the methods and solutions used to construct the tunnels and stations, with a focus on the requirements for construction of the station to be a civil defence shelter if required. This involved solutions to tying reinforcement and placing concrete to high standards in a restricted space, as well as the incorporation of heavy blast doors and other associated protective measures. The efforts of the management team resulted in the project being awarded first prize in the 2011 Land Transport Authority’s Annual Safety Award Convention and being named winner of the Safety and Health Award Recognition for Projects (SHARP) award at the 2011 Workplace Safety and Health (WSH) Awards. As well, McConnell Dowell won a Green and Gracious Builder Award (Excellent Category) from the Building and Construction Authority (BCA).CITATION:McDonough, R, 2014. Design and construction contract C916 Beauty World Station and Tunnels, Singapore, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 411–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By F F. Pitard

The optimisation of a metallurgical plant requires two kinds of sampling systems. The first provides samples to follow process changes, so in due time actions to maintain key parameters within pre-established specifications can be applied. The second provides composite samples at the end of a working shift to demonstrate that valuable constituents sent to the plant went to either a final concentrate or to the tailings in a logical, expected proportion. Contrary to what many experts may claim, these two kinds of sampling requirements are incompatible and cannot be fulfilled using the same sampling systems; this is because the required samples have completely different objectives. A process control sample is an instantaneous sample with increments taken at short intervals, and the objective is to know where the process is at any given time. Excellent accuracy is not a must, however good precision is recommended since a possible process correction may need to be made. Online analysers fed with in-stream stationary cutters or other kinds of in-stream or by-stream probes can do well for such a mission. A composite sample for metallurgical accounting with increments collected over a long period of time, for which excellent accuracy and good precision are both required, must be generated by sophisticated and extremely well-maintained cross-stream sampling stations. The use of process control sampling systems to achieve good metallurgical accounting has been promoted by several manufacturers of sampling equipment around the world; it is a grave mistake that is misleading top management and a practice that should be scrutinised and preferably eliminated. Furthermore, bias tests used to prove otherwise are often based on insufficient data to draw valid conclusions; a guideline is provided.CITATION:Pitard, F F, 2014. Sampling systems for process control and metallurgical accounting, in Proceedings Sampling 2014 , pp 25–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023

By P Holtham, K C. Runge, E Tabosa

Traditionally, comminution and flotation have been surveyed, analysed and optimised separately. This often results in less than optimal outcomes because of the complex interactions between the two processes. Flotation recovery is a strong function of the valuable mineral particle size distribution with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation. Thus, to optimise flotation recovery and grade it is usually best to grind to a fine size. This requirement needs to be balanced by the cost of grinding finer and the revenue that results from an increase in grinding throughput, which often results in a coarsening of the flotation feed.This paper demonstrates a technique which can be used to predict the effect of a change in feed grind size on flotation performance. It can be used to determine the optimum grind size for a particular operation which optimises total circuit profitability. Analysis is relatively easy to perform, as a minimum, requiring only size by assay data of the feed and product streams of the process. Case studies will be presented that demonstrate the usefulness of this technique in feed grind applications. Potential use of the technique for regrind evaluation is discussed. The limitations associated with this technique in certain circuit scenarios will also be outlined.CITATION:Runge, K C, Tabosa, E and Holtham, P, 2014. Integrated optimisation of grinding and flotation circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J Rowland

"This paper was primarily put together in order to demonstrate what are believed to be acceptablestandards, in relation to ventilation surveys and the subsequent model assembly process. Thiswas brought about by the fact that in many parts of the world it is regarded as acceptable to carryout ventilation surveys and then build and supply the client with a æstick fi gureÆ type ventilationmodel. Such stick models have arguably litt le use and a very short life span in the real world and isalmost impossible for site staff to maintain. Thankfully most underground coal mines in Australia strive to maintain a true replica model of their ventilation circuits and to keep them in a relatively good state. Given that these mines own and maintain the models, it is often seen as necessary to update or rebuild them. The level of survey detail required to do so is totally dependent on the end use of the data and the criticality of the accuracy of the data set, to the ongoing safety and viability of the business. Mine technical personnel should think clearly about the use and importance of the ventilation survey and subsequent report outputs required that will help them bett er understand their mines and bett er prepare them to manage their ventilation circuits, on an ongoing basis. This paper provides some guidance for Australian ventilation engineers so they may plan and execute this work æin houseÆ, should they rightly choose to do so. To this end, methods of data collection and circuit analysis required for surveys of a high order of accuracy are detailed. Also, some of the issues which are important when formulating a strategy to carry out the appropriate ventilation survey for the required purpose are summarised. As well, the major details that should be furnished within any survey and some survey/report outputs and/or omissions, which are clearly not acceptable, are highlighted."

Jun 1, 2012

Located 350 km west of Sydney and 20 km outside Orange, NSW, lies the Ridgeway Gold Mine û NewcrestÆs flagship Underground Gold Mine. Key to success at Ridgeway has been the fast tracked development of the 3.8 km, 1 in 5.3 conveyor decline which houses the 850 t/hr conveying system feeding the dedicated Ridgeway Concentrator, built adjacent to the existing Cadia Hill Concentrator. Eroc was contracted to develop the steep conveyor decline, drawing on its personnel and experience from past metalliferous, tunnelling and coal mining projects to complete the ambitious schedule within 12 months. This paper deals with the complexities and experiences in safely delivering what is understood to be one of AustraliaÆs steepest declines of any substantial length in a metalliferous mine.

Jan 1, 2002

By P J. Vardon, L A. van Paassen, Y Yao, A F. van Tol

Thin-lift atmospheric fine drying (AFD) is a technique used to dewater mine and oil sand tailings, which utilises both self-weight consolidation and atmospheric evaporation. The disposed layers undergo a cyclic drying and rewetting process due to precipitation and deposition of additional lifts on top of the dried layer. The current research aims to optimise the deposition process via use of a numerical model and realistic atmospheric conditions, including both periods of drying and wetting. The model is based upon water balance and includes large strain considerations. A number of material behaviours are characterised using empirical fitting curves based upon laboratory measurement of material characteristics, including both the shrinkage and water retention curves for drying and rewetting. The model is able to model multiple lifts, simulating field scale and realistic climatic conditions within timescales suitable for engineering practice (eg seconds or minutes). The model has been previously validated against controlled laboratory experiments and utilised to simulate field tests. A series of simulations are presented to illustrate the ability of the model to be used as a practical tool for the optimisation of a tailings deposition strategy.CITATION:Vardon, P J, Yao, Y, van Paassen, L A and van Tol, A F, 2015. The use of a large-strain drying and consolidation model to optimise multilift tailing deposits, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Scott, I Onederra

A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful empirical or engineering models are currently available to blasting engineers and consultants, while more sophisticated approaches using mechanistic and numerical descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The fragmentation resulting from any blast will be heavily dependent on the properties of the rock mass being blasted; however, most empirical models rely on ‘rock factors’ generated from simple rock mass properties to describe the influence of the rock on the blasting outcome. In contrast, mechanistic models need explicit rock mass properties that require sophisticated laboratory measurements and detailed structural data if realistic outcomes are to be generated. The fragmentation modeller is caught between excessively simple rock mass descriptions for the empirical models and excessively complex data requirements for the mechanistic models.This paper briefly reviews the basis of a range of fragmentation models and the rock mass properties on which they rely. Shortcomings in the way that the mining industry tends to characterise the blasting properties of rock are discussed and some practical approaches are described to quantify these properties in both operating and greenfield mining environments. Case studies are presented where specific additional breakage properties and modelling features have been needed to generate a useful description of the fragmentation achieved.CITATION:Scott, A and Onederra, I, 2015. Characterising rock mass properties for fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 149–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The sulphide ore occurring in the North Mine at Broken Hill is of a complex nature, consisting of an intimate mixture of argentiferous galena, marmatite (zinc-iron sulphide), and gangue minerals. A typical analysis of the ore is:Lead 15.2%Zinc 12.0%Iron 5.3%Manganese 0.8%Copper 0.1%Alumina 0.3%Lime 0.9%Sulphur 11.1%Insoluble 53.8%Carbon dioxide 0.3%Undetermined 0.2%Silver 9 oz. per tonTotal 100.0%The metallurgical practice for the recovery of the lead concentrate and zinc concentrate from the crude ore is briefly described in the following pages.(1) COARSE CRUSHING AND FINE GRINDING OF THE CRUDE OREThe crude ore from the mine, containing lumps to the size of, roughly, 10 in. x 8 in., is tipped over grizzlies with the bars spaced 3 in. apart; the oversize gravitating to a...

Jan 1, 1933

Bureau of Medical Inspection, Broken Hill, New South Wales.INTRODUCTIONFor a considerable time it has be3n realised that the pathological changes produced in human lungs by the inhalation of free silica varied, not only according to the amount of silica inhaled, its particle size and the period during which it was inhaled, but also according to other mineral elements which might be admixed with the fine silica dust and inhaled along with it, or inhaled subsequently to the silica containing dust. It was observed that, in many instances, these admixed dusts tended to inhibit the action of the free silica in causing injury to the lungs, as well as the development of certain complications, whilst in other cases it was felt that certain substances could actually accelerate the tissue damage caused by the silica.A fresh impetus to the problem of the prevention of the development of silicosis was given when, in 1937 and 1939, Denny, Robson and Irwin published papers entitled "The Prevention of Silicosis by Metallic Aluminum." Working at the same time at the Saranac La.boratory, and quite independently, and using a colloidal aluminum hydroxide, Gardner arrived at the same conclusions as Denny, Robson and Irwin, namely, that in experimental animals the development of silicotic changes could be prevented if eithertogether with the silica, or subsequent to its inhalation...

Jan 1, 1946

Accurate geometric models of orebodies establish the framework for reliable mineral resource estimates that provide a basis for further exploration and mine planning, as well as for financial models that ultimately determine the economic viability of a deposit. Traditional, explicit geometric modelling techniques that are utilised for resource modelling by the general mining software packages, such as MineSight«, involve manually digitising interpreted ore outlines that must be carefully linked to create valid geometric solid models. An alternative, implicit modelling method, employed by LeapfrogTM software relies on a fast method of global interpolation, which offers several advantages over traditional modelling techniques. Although previous case studies have documented the relative efficiencies of the two approaches, the accuracy of the two methods has not been previously quantified and compared. This study quantifies the accuracy of solid models created using explicit and implicit methods, and compares the differences between the models. Solid models of the Doris Hinge vein gold deposit (located in the Hope Bay district, Nunavut, Canada) are constructed from preliminary and follow-up drilling data using both modelling techniques. The accuracies of the solid models generated using preliminary drilling data are determined by measuring the 3D distance between the surface of the models and the actual contact location defined by the follow-up drilling data. Additional comparisons based on volume, cross-sectional area and surface differences were made between both phase 1 solid models and solid models constructed from phase 2 drilling information. The overall results of this study find that the MineSight« and LeapfrogTM solid model accuracies are virtually the same, and that their volume, cross-sectional area, and surface differences are comparable. This study concludes that the implicit modelling technique generates accurate solid models that can be used in place of explicit models as ore shells for resource estimation in certain circumstances.

Jan 1, 2006

By R Schiller, E Chait

"Quebrada Blanca is a porphyry copper deposit located in the Eocene-Oligocene belt of Chilean Andes. Operation started in 1994 and original reserves for supergene mineralisation gave a life-of-mine (LOM) of 20 years; however, further exploration extended the LOM until 2020.In order to optimise the remaining five years of supergene resource, geometallurgical variables were added to the geological model including copper recovery and acid consumption. LOM plan encompasses finishing the phase number eight and the future development of phases 11 and 13.LOM lithologies include diorites, quartz monzonites, porphyries, igneous and tourmaline breccias. Main alterations are: potassic, phyllic and argillic. Litho-alterations or geometallurgical units were formed by combining five types of rocks with three types of alteration. According to statistical information, the deposit can be represented with 12 litho-alteration units, which cover 98 per cent of the LOM volume.For copper recovery information, there were 40 mini-columns tests made in order to obtain kinetics curves and copper recovery values after comparing the difference between head and tails grades. Acid consumption was obtained using an automatic neutraliser device-based test.Historical data said that copper recovery in pads after 450 days of irrigation is around 75 per cent of recoverable copper while acid consumption is around 5.5 kg/t.According to this study, lower recoveries are related with potassic-altered diorites and argillic-altered quartz monzonites with values around 60 per cent. On the other hand, best recoveries could be found in potassic-altered quartz monzonites and argillic-altered diorites with values closer to 80 per cent.It was also revealed that the most reactive rock is the potassic-altered diorite with 12 kg/t of acid consumption. This rock covers approximately 40 per cent from phases 11 and 13.The final geomet model was calculated using a program that relates each geometallurgical unit with a specific copper recovery and acid consumption value. Results found after comparing model-obtained information with historical leached pads data were used to validate the model.CITATION:Chait, E and Schiller, R, 2016. Adding Copper Recovery and Acid Consumption Variables to the Geological Model of Quebrada Blanca, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J Battista, J Grace, I Brunton

The need to better understand and develop strategies to improve instantaneous shovel productivity at the Cadia Hill Open Pit Mine (CHM) instigated the development of the æShot to ShovelÆ project. This project has involved the implementation of a drill and blast (D&B) information management system to capture current and future experience. Equally important has been the manual monitoring of shovel productivity and direct use and analysis of high precision GPS and productivity data logged by ModularÆs Dispatch System. The analysis of this type of data was facilitated with the application of GIS based software (ie MapInfo). This has shown to be a powerful medium to display, interpret and assess this type of spatial information on a blast-by-blast basis. Cadia HillÆs well-defined D&B processes supplemented with the application of the above systems are providing a unique capability to assess and better understand the impact of both muckpile conditions and operator proficiency on instantaneous loading productivity. This is facilitating the definition of appropriate optimisation strategies in both drilling and blasting and operator proficiency training. This paper gives a summary of the work conducted in the æShot to ShovelÆ project, describes the engineering tools being implemented and discusses preliminary findings and their practical implications.

Jan 1, 2004

By R Castedo, P Segarra, I del Castillo, L M. López, J A. Sanchidrián

This work investigates some suggested methods for blast vibration monitoring on a hard surface based on 53 tests on a vibration exciter. Errors in the measurement attributable to coupling have been described as function of frequency by the rock-to-mount (or coupling) transmissibility, ie ratio of the velocity of the vibration sensor mount to the velocity of the rock motion. Transmissibility has been measured from 2 to 200 Hz, at two vibration levels (5 and 20 mm/s), in four seismographs. Attachment methods with an anchor, thermal adhesive and gypsum plaster allow stiff rock-to-mount coupling. They ensure accurate measurements (errors below 0.3 dB) for frequencies commonly found in blasting (below 100 Hz) irrespective of the mount characteristics and the vibration level. Free laid mounts and sandbagged vibration sensors lead generally to a poor, weak coupling. Errors are non-linear errors with the input velocity, ie the operating frequency window narrows as the velocity of the ground increases. Free mounts follow ground motion acceptably well (error up to 0.4 dB) at both vibration levels and frequencies below 15 Hz. At higher frequencies, free mounts lead to the largest distortions with expected errors ranging from 0.8 to 6.6 dB. Sandbagging limits the expected errors below 1.3 dB, but it does not prevent large errors that can be up to 4.5 dB. Both frequency and velocity should be considered together to assess the measurement errors instead of the expected accelerations, as it is currently made.CITATION:Segarra, P, Sanchidrián, J A, Castedo, R, López, L M and del Castillo, I, 2015. Effect of vibration sensor mounting method on the quality of vibration measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 545–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015