Search Documents

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

By J Zhou

This paper discusses the implementation of a mixed integer linear programming model for a coal preparation plant. The plant considered consists of primary and secondary heavy media cyclones, hydrocyclones for intermediate fines and froth flotation for the very fine material. The model is designed to optimise the plant settings and product flows to maximise revenues for a given specification for two product outputs. The model can deal with bonus/penalty aspects of the product pricing for products that exceed or fail to meet specification. We report on a model with two separate coal feeds with parallel circuits for the oversize, intermediate and fines streams. The genesis of this model is more than 30 years old but recent improvements in mixed integer programming solvers make a full mixed integer formulation practical. The original model began as an enumeration of cut points with arbitrary rules for product allocation. The product allocation was improved in a linear programming formulation by Gunn (1982) and Sarker (1991 and 1995). Current mixed integer programming capabilities make it possible to replace the enumeration aspects and solve directly as a mixed integer programming problem. The current implementation uses a general purpose modelling language to formulate the model. Open source and commercial mixed integer programming solvers are compared

Sep 26, 2011

By Tilley H. L

The 90 m deep Yallourn Open Cut brown coal mine in the Latrobe Valley, Victoria is developing into an area close to a reverse fault. A major batter stabilisation program, matched to ongoing operations, has com- menced to maximise coal recovery where the fault is within 100 m of the Open Cut. The various mine development options considered during the planning stages are outlined. These options were formulated in a back- ground of geotechnical constraints and the need to maintain continuous and reliable coal supply at a time when a new coal field would be developed. The geotechnical investigations and analysis procedures under- taken to determine stability of the batters during their excavation are presented. The geotechnical constraints on the mine design and opera- tions required to ensure safe working conditions are detailed. Current operational and batter stability conditions are considered satisfactory.

Jan 1, 1989

By N Esmaeili, M Saghaeian, L Hosseini, V Sheikhzadeh, R Hejazi

Ore roasting has long been used for beneficiation and assay upgrading of different ores. In this process, which is mainly used for sulfide ores, the ore is heated to a high temperature. More specifically, it is a metallurgical process involving gas-solid reactions at elevated temperatures. Some types of Iron ore are weak in magnetic properties. Hematite, goethite and limonite are classified in this group. Unlike magnetite, which shows strong magnetic susceptibility, these ores are hard to beneficiate through magnetic separation route. Many researches have focused on gravity separation and flotation routes for upgrading these ores and these methods have also been utilised in the industry. One of the methods to whose industrial application less attention has been paid is magnetising roasting in which the non-magnetic iron ore is transformed to magnetite which is further beneficiated through magnetic separation. In this study, magnetising roasting tests have been performed on one goethite sample in order to check the feasibility of using this method for this specific ore in industrial scale. It is worth mentioning that high intensity magnetic separation have been performed on this sample before but the achieved results were not promising. Results have revealed that through magnetising roasting magnetite content of the ore could be increased from 1.7 per cent up to about 25 per cent. FeO content of the feed sample was increased from 1.03 per cent up to around 9.25 per cent. Also optimum size distribution for achieving the best results in magnetising roasting for this sample has been determined through this study. The best results were achieved when the ore size was 0–10 mm. The effect of coal ratio, time and temperature on the process have also be studied. A coal ratio of 5 per cent, time of 30 min and a temperature of 850°C were determined to be the optimum conditions. Finally, the technical feasibility of utilising magnetising roasting for this specific ore has been confirmed.

Aug 24, 2022

By T Baumgartl, C Gonzales, A Soliman, M Edraki

A soil cover isolates potentially acid-forming (PAF) mine wastes from atmospheric interaction and thereby mitigates acid mine drainage. As a cover that comprises either a single layer or a composite barrier, it essentially manages percolating rain water from flowing into these PAF materials and minimises air flow as oxygen has low diffusivity in saturated soils. However, the availability of suitable soils as cover materials is limited, especially in arid and semi-arid regions where weathering rates are low.This paper investigates the potential use of mine wastes as cover materials in a water-shedding soil cover in north-west Queensland. Four cover trial plots were built using mine wastes as cover materials. Each 2.3 m cover trial plot consisted of a 1.5 m soil cover made up of waste rocks and fines, a 0.5 m drainage layer that consisted of 0.1 m waste rock aggregates and a base layer made up of blended mine tailings. The hydrologic properties of cover materials were determined by in situ measurements and laboratory experiments, which, in turn, were used as input in a numerical model that described the cover’s transient soil moisture profile. The successful performance of the cover is reliant on the long-term stable geochemical behaviour of the substrate used as cover material. Therefore, investigations were carried out to determine the geochemical properties of the cover materials constructed from benign waste rock using static and kinetic tests, with the objective to increase the level of certainty of the material’s benign characteristics. Consequently, the long-term performance of this water-shedding cover design is described in terms of the physico-chemical characteristics of its outflows.CITATION:Gonzales, C, Baumgartl, T, Edraki, M and Soliman, A, ?2014. Mine wastes as cover materials in a water-shedding soil cover in north-west Queensland, in Proceedings Life-of-Mine 2014 , pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Camarda, A Pirson, F Vasconcelos, J Mesquita

ArcelorMittal Prijedor is a goethitic iron ore mine located in the north-west of Bosnia and Herzegovina, which mainly supplies ArcelorMittal’s European subsidiaries. Annual production of the asset stands at the level of 1.5–2.1 million tons of iron ore product which is sent to ArcelorMittal Zenica steelmaking plant. Two types of products with approximately 50 per cent Fe are generated in Prijedor through a process composed by crushing, screening, and magnetic separation stages. Within this process one of the tailings produced is called ‘ultrafines’. The ‘ultrafines’ product corresponds to the desliming hydrocyclones overflow in Prijedor plant, which is classified in a size fraction below 25 μm and corresponds to about 5 per cent of feed. This material is richer in iron than the coarser size fractions of the ore but do not present a good performance in concentration processes. In this way, several studies have been carried out during the last years to find solutions to use the ‘ultrafines’ material without success. In this context, the possibility of dehydroxylate the goethite contained in the material transforming the mineral into hematite and thus increasing the iron grade of the final product was investigated. During the research, several dehydroxylation tests with different temperatures and time of exposure were performed. Using dihydroxylation process at temperatures higher than 800°C it was possible to produce a material with 43 per cent Fe from the original 39 per cent Fe ‘ultrafines’ sample. In addition, the dehydroxylation tests confirmed that goethite becomes completely transformed into hematite at 400°C (with an exposure time of 60 mins) and material is completely sintered at 1200°C. A simulation study based on dehydroxylation tests results showed that it would be possible to use a ‘ultrafines’ product with Fe grade higher than 45 per cent to produce a material with 50 per cent Fe through a complete dehydroxylation process.

Sep 18, 2023

By He BQ

Static attachment of bubbles to solids is contrasted with dynamic attachment in flotation cells. The times of contact during particle-bubble collisions in dynamic attachment are compared with the induction time determinations and the kinetics of thinning of the liquid films separating solids and bubbles. The thinning is examined mainly in terms of electrostatic and dispersion (van der Waals) contributions to the disjoining pressure existing in the films. The local heterogeneity (on a molecular scale) of charge distribution invariably present at all interfaces (even at conditions of zero zeta potential) calls for some means to minimize possible electrostatic repulsions which arise when the electrical double layer at the air-bubble interface begins to overlap that present at the solid surface, on encounter between particles and bubbles. It is postulated that dipoles of frother molecules, owing to their ability to "flip over" (polarise), replace localized electrostatic repulsion by attraction within fractions of a milli- second, as long as the structure of the frother molecules is sufficiently "bulky" to maintain diffuse films (of mixed collector-frother) at the air/liquid interface of bubbles. The relaxation times of dipoles (signifying their "flipping over" ability) have to be shorter than the collision times between particles and bubbles for particle-bubble attachment to be facilitated under dynamic Conditions.

Jan 1, 1984

By S C. Dominy

For any gold deposit-based geometallurgical study, the collection and processing of representative samples for gold grade and recovery tests is critical. Sampling protocols should be designed to suit the style of orebody in question. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols and metallurgical recovery processes employed. Studies focussing on ore mineralogy and gold particle deportment, size and distribution are required. Key issues are the presence of gold particle clustering (important for sampling optimisation) and proportion of coarse versus fine to refractory gold. X-ray computed tomography (CT) is a radiographic technique that produces high-resolution 3D computerised models of objects based on density distribution. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels each assigned a grey value based on X-ray absorption. This paper presents the results of recent research on the imaging of in situ gold particles in a coarse gold-bearing ore. The technique shows promise as a rapid non-destructive method for preliminary characterisation to facilitate more detailed studies. Early and rapid gold particle determination enables sampling protocol optimisation and metallurgical recovery parameters to be defined prior to detailed feasibility studies

Sep 5, 2011

By D Q. Zhu

In this paper, the pretreatment of concentrates by roller press was present to improve the granulation of blends comprising some 30 per cent iron ore concentrates and enhance the sintering performance. It is shown that by pretreatment of fine concentrates through roller press, the content of +3 mm fractions of granulation mixture and sinter mixture permeability are elevated by ten per cent and 35 per cent. In the meantime, a sinter productivity increase from 1.51 - 1.62 t.m-2.h-1 is attainted in pot tests with similar sinter tumble index and at lower coke rate. The mechanism of the pretreatment of concentrates process to improve sintering performance of fine iron ore concentrates was demonstrated by mineralogy that better permeability help form more calcium ferrite and good microstructure of sinter, further proven by the better metallurgical performance of sinter.

Jul 11, 2011

By M Saghaeian, M Zare, V Sheikhzadeh, R Hejazi

High-Pressure Grinding Roll (HPGR) is one of the efficient methods for increasing the specific surface area (SSA) of iron ore concentrate for pellet feed production. HPGR grinding mechanism implies that material should compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study, by doing SSA increasing tests with pilot HPGR, the effects of silica reduction on SSA increasing results were investigated. For this purpose, HPGR tests were performed on an Iranian magnetite concentrate before and after reverse flotation silica reduction tests. Based on the laboratory test results, silicates have been concentrated in two fraction sizes of the sample comprises coarser than 150 microns in form of quartz and finer than 7 microns in form of iron silicates. These silicates have been effected on reduction of concentrate bed pressure resistance by creating a pasty and sticky mud. In this condition, HPGR cannot work properly and operation results are not acceptable. According to flotation silica reduction tests, with 90 per cent weight recovery, concentrate Fe grade is increased from 67.8 per cent to 69.5 per cent and SiO2 content is reduced from 1.98 per cent to 0.9 per cent and especially for lower than 7 microns fraction size, as a critical fraction, SiO2 content decreased from 4.45 per cent to 2.35 per cent. HPGR tests were performed on 8 per cent moisture in 4 N/mm2 specific force and according to the results after silica reduction HPGR operation conditions are optimised. Results showed that the working gap increased from 7 to 10.5 mm and specific throughput of material raised from 180 ts/hm3 to 250 ts/hm3 , and SSA increased by 300 cm2 /gr in a single pass.

Aug 24, 2022

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By K Nilsson, G Cheong

Troy Resources NL acquired a 70 per cent interest in the Mina Sertpo gold project in Goißs State, Brazil, in 2001 following a successful bid for the highly competitive international tender of a tenement package put out by Western Mining Corporation (WMC). The Sertpo deposit is located on cleared grazing land 380 km west of Brasilia and is 30 per cent owned by Amazonia Mineracao Ltda, a private Brazilian company. It is a small high grade open-pittable orebody with a measured and indicated resource of 108 000 tonnes at a grade of 49.7 g/t for 172 500 ounces using a 2.0 g/t cut-off. Troy undertook the project management and development of the project while Amazonia managed the exploration activities and provided other services as required. The project development involved drilling metallurgical test holes, scouring the world to locate an available and suitable second-hand plant, and arranging shipping to andreconstruction in Brazil.

Jan 1, 2004

By S Q. Zhao, J H. Wei

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Xitieshan lead-zinc deposit is located in the north margin of the Qaidam Basin, Qinghai Province, China. It is one of the largest massive sulfide deposits in China and is supposed to be of the sedimentation-exhalation (SEDEX) type. Based on the main ore mineral and sulfur isotopic compositions in sulfides found in the wall rock, the S of the deposit is considered to originate from the mantle, but the fluid potentially mixed with sea water during the hydrothermal circulation exchange. The study of lead isotopes shows that the metallogenic material is characterised by the mixture of orogenic and upper crust sources. The lead isotopic signature of the wall rock is similar to that of the ore, which shows synsedimentary characteristics. According to the composition of the rubidium and strontium isotopic signature, the value of 87Sr/86Sr is lower than the average value of that in the crustal rock, which is larger than that of the mantle. Hence, the metallogenic materials of this deposit mainly originate from the crust, which is related to materials of volcanic rocks activation and migration of the deep hot circulating water. The process of the metallogenic fluid circulation shows continuous interaction with crustal material and lead to continuous enrichment of the ore forming fluids. From the study of the fluid inclusion microthermometry of the ore and the associated minerals combined with the C, H-O, Si isotopes, it is believed that the metallogenic fluid is mainly coming from the mantle or the deep magma chambers. The rising deep fluid then mixes with the sea water. The carbon dioxide escaping and mixing with sea water during the hydrothermal exhalation process leads to the rapid precipitation of the hydrothermal fluid to deposit metal. That is proposed as the principal formation mechanism of the Xitieshan deposit. Further studies are proposed, including obtaining geochronology data from this deposit.CITATION:Zhao, Z X, Wei, J H, Liang, S N and Zhao, S Q, 2015. Advances in research on metallogenic mechanisms for the Xitieshan sedimentation-exhalation lead-zinc deposit, Qinghai Province, China, in Proceedings PACRIM 2015 Congress, pp 487–494 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By C Munro, S Emery, M Flynn, K Tan

"AEROPHINE® 3418A Promoter is a well-known and widely used collector and is an industry standard for its excellent selectivity and efficacy in the processing of complex polymetallic sulfide ores, particularly those containing silver. Until now, however, it has not found widespread use in primary nickel flotation.In an effort to increase nickel recovery without compromising selectivity over iron sulfides, Western Areas Forrestania Nickel operation trialled the use of AEROPHINE® 3418A as a secondary collector at low dosage. A series of ON/OFF trials were conducted, with the finding that a very low dose of AEROPHINE® 3418A increased nickel recovery by 0.6 per cent compared to using xanthate alone.This paper provides a brief operational history and overview of the Forrestania operations, a description of the trial and an analysis of the results.Citation:Emery, S, Flynn, M, Tan, K and Munro, C, 2016. Aerophine® 3418A Promoter as a Secondary Collector to Boost Nickel Recovery at Forrestania Nickel Operations, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Callie underground gold mine is part of the Newmont Tanami Operations, and is now the primary provider of ore to the Granites processing Mill. The Callie underground mine has produced in excess of 7.6 million tonnes (Mtpa) of ore, since production began in 1998, with a current production rate of 1.9 Mtpa. Callie underground uses sublevel open stoping with extraction through a combination of primary and secondary stopes. The primary stope filling strategy utilises cement aggregate fill (CAF) to allow full recovery of secondary stopes. The Callie backfill operation has had a continuous testing program in place during this time, which has resulted in a great deal of information available for post fill analysis. All CAF placement into primary stopes for Callie has been via surface boreholes and this has given Callie mine an understanding of some of the issues related to borehole design, type of linings to use depending on angle, depth and quantity of fill into stopes. Finally backfill barricades at Callie have undergone a number of changes during the time to optimise the design based on whether CAF or sand fill is used. This paper discusses the CAF backfill practices and testing methods used for backfilling operations at Callie.

Jan 1, 2005

By N Maistry, C Carelse, A Singh

Banded Iron Formations or more commonly known as BIF are sedimentary rock formations with alternating silica-rich layers and iron-rich layers that are mainly composed of iron oxides (hematite and magnetite), iron-rich carbonates, and/or iron-rich silicates. Considering the depletion of highgrade iron ore reserves in South Africa, there is a need to maximise resource utilisation through the exploitation of low-grade/uneconomic resources particularly BIF material, which makes up more than 65 per cent of current reserves. Previous test work conducted by alternative BIF sources globally indicates the need for fines processing in order to produce a concentrate. South African BIF however is amenable to coarse and fines processing producing an on-grade product or blended feedstock. C-Type material within South Africa’s Northern Cape Province grading at approximately 33 per cent Fe was supplied for research purposes. Top size optimisation via gravity Heavy Liquid Separation (HLS) tests was conducted. The laboratory results being perfect separation (Ep=0) were modelled to predict pilot performance, the results of which were tested on a pilot scale for the finest size fraction (-1 mm). It was observed that a top size of -2 mm provided optimum results in terms of upgrade and recovery, with crushing finer not necessarily producing superior results. At a target grade of 60 per cent Fe, recoveries of 65.6 per cent were achieved on the laboratory scale, whilst recoveries of approximately 58 per cent were achieved on the pilot scale. Targeting higher upgrades of 63 per cent would inevitably result in lower recoveries of 57.2 per cent on a laboratory scale and approximately 54 per cent on a pilot scale. This is in line with grades and recoveries achieved globally for BIF material albeit at finer grind sizes.

Sep 18, 2023

By Y Zhu, D J. Williams, M O’Neill, C Zhang, X Lei

A cover of inert material overlain by topsoil is required over compacted, seawater-neutralised red mud, a waste product from the refining of bauxite to produce alumina. The cover is to be revegetated, and it is necessary to demonstrate that the potential evapotranspirative-driven uptake of salts from the seawater-neutralised red mud will not impact the revegetation. An instrumented column was designed and constructed to test the evaporation-driven uptake of salts from compacted red mud into an overlying cover material with a thickness limited to 600 mm. The PVC column is 1.2 m high, with a 200 mm internal diameter. The column is instrumented with up to ten of each of moisture, suction, salinity and temperature sensors, together with a data logger, designed and manufactured at The University of Queensland (UQ) in Brisbane, Australia. The sensors were installed through the wall of the column at various depth intervals, with each set of sensors located at quarter points around the circumference of the column. Two pressure transducers were installed in the column to monitor the change of water level due to rainfall and evaporation. The column was filled with compacted red mud to a depth of 600 mm overlain by 600 mm of cover material, both sourced from the Queensland Alumina Limited (QAL) site in Gladstone, Queensland, Australia. The column is installed on a building roof at UQ, alongside a weather station, and will be subjected to the prevailing weather conditions for up to 1 year in the first instance, during which time the weather conditions and sensor responses will be continuously monitored. This paper reports on the instrumented column set-up and the early results obtained from the test.CITATION:Zhang, C, Williams, D J, Lei, X, Zhu, Y and O’Neill, M, 2018. Instrumented column testing of salt uptake from compacted red mud into a cover, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 220–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By F Clark, J T. Carswell

Ore definition for final stope planning is often a challenging prospect in underground (UG) gold mines which exhibit high geological and grade variability. Unlike the grade control (GC) scenario in an open pit (OP), the ability for the mining geologist to plan a sampling campaign which effectively characterises the underlying mineralisation is fraught with difficulty. UG sampling patterns are strongly clustered and typically not dense enough to characterise the spatial and statistical properties. Very commonly, sample volumes are not large enough to provide a reliable grade estimate of the surrounding rock. These factors critically affect our ability to accurately map out ore positions and estimate metal quantities.At Sunrise Dam, traditional UG sampling and modelling techniques have proven to be an unreliable strategy for successful stope planning and extraction. The problem was first observed during the final cut-back in the open pit for which the mineral resource model was constructed from UG diamond drilling. Open Pit grade control reconciliations were strongly positive for both tonnage and grade compared to the resource model. Underground workings missed significant quantities of ore which was laterally defined by open pit reverse circulation (RC) GC drilling. Upon examination it was realised that the cause of the problem was one of inadequate sample density and sample support, the implications of which potentially affected the entire UG mine.As part of a broader study into underground grade control procedures, detailed reconciliation of initial stope production from the GQ domain also pointed to inadequate sampling as a major constraint to effective grade control and reserve conversion.To overcome this deficiency, dense 115 mm wet RC grade control drilling and conditional simulation modelling has been successfully implemented with the intent to replicate the grade control process in the open pit. The increase in sample density and sample volume has proven to be a very effective tool for mapping out highly complex mineralisation. A marked improvement in stope definition, reserve conversion and Mine to Mill reconciliations has been demonstrated on the back of an innovative approach to UG grade control.CITATION:Clark, F and Carswell, J T, 2014. Using reverse circulation drilling to improve sampling in a complex underground gold operation – an innovative approach to underground grade control at the Sunrise Dam Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 143–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By R Strand, L Reading, G Keir

A major challenge in managing coal seam gas (CSG) water is predicting how much water will be produced as the industry develops. Klohn Crippen Berger Ltd (KCB) was commissioned by the Queensland Department of Natural Resources and Mines (DNRM) to develop a tool to forecast where, when and how much CSG water will be produced in the Surat and Southern Bowen Basins under various industry expansion scenarios.The water production tool (WPT) uses the Theis equation, a non-equilibrium groundwater flow equation that accounts for the effect of pumping time on well yield in confined aquifers, to predict water production volumes. Where multiple pumping wells are in close proximity, the required pumping rates for coal seam depressurisation are reduced. Therefore, pumping effects are projected spatially to assess interference effects between wells. Water production is then upscaled to the projected scale of the CSG industry within the Surat and Southern Bowen Basins.Two modifications were made to address the dual phase nature of CSG extraction (a transmissivity reduction factor) and the impact of weathering at the eastern margin of the Surat Basin (a ænear edge effectÆ factor). These factors modify relevant hydrogeological parameters in a consistent and defensible manner to more closely match observed water production.The WPT was verified by comparing results to equivalent Theis equation calculations and to type curves provided by CSG proponents. Calibration was achieved by varying the spatial distribution and intensity of the near edge effect factor in conjunction with a chi-squared analysis of residuals.The tool, which is now being maintained and further developed by the Centre for Water in the Minerals Industry (CWiMI), was built to balance numerical complexity against relative flexibility and simulation speed. The result is a tool that can produce statistically relevant results of prescribed scenarios to plan water handling and treatment requirements in discrete zones of operation.CITATION:Strand, R, Reading, L and Keir, G, 2013. Water production simulation tool for coal seam gas operations in Bowen and Surat basins, in Proceedings Water in Mining 2013 , pp 311-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013