Search Documents

By N Madani

Linear interpolation of geo-related variables is important to different aspects of mining engineering such as long and short-term mine planning. The ore deposit description attained from spatial modeling of blast hole datasets has been widely taken into account, particularly, for short-term mine design and grade control, so as to define the ultimate destination of a mined block. It is approved in practice that making the wrong decision leads to losing a huge amount of money for choosing the destination of a mined block. In the case of complex ore deposits, the issue of estimation of variables in the region is questionable and somehow tedious. Due to this fact, modeling those complications in the co-spatial behavior of the grades in multi-element deposits prompts one to employ enhanced geostatistical techniques. Traditional approaches of this purpose such as polygon, inverse distance weighted and even (co)-kriging approaches, are incapable of reproducing those complexities such as non-linearity, heteroscedasticity and geological constraint that frequently exist among the variables of interest in those deposits. Another difficulty in employing those linear interpolations in grade estimation is smoothing effect, in which the estimated grades are over and under estimated. CITATION: Madani, N, 2018. 3D estimation of variables with complexity in cross-correlation structures, in Proceedings Complex Orebodies Conference 2018, pp 49–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M C. Schodlok

Banded iron-formation (BIF) and iron ores were measured using the CSIRO developed TIRHyLogger ™ to assess its ability to map quartz, carbonates and riebeckite. The TIR-HyLogger™ measures continuously spectral refl ectance data from diamond drill core or drill chips with a high spatial and spectral resolution. Samples from twelve BIF, bedded iron deposits (BID) and channel iron deposits (CID) have been analysed. The spectral data were processed with two different approaches. The first approach, focused on the identifi cation of the major minerals, was performed using principal component analysis (PCA). It identified four minerals (quartz, ankerite, riebeckite and goethite) and provided pure spectra called end-members. The second approach included a mineral diagnostic spectral feature extraction involving wavelength position, relative peak heights and relative depths of absorptions. Quartz has a diagnostic absorption at 8.625 µm and ankerite shows a refl ectance peak at 11.275 µm. In addition to the identified end-members, two carbonate populations (calcite and siderite) and two silica species (quartz and amorphous silica) were identified.

Jul 11, 2011

The production of synthetic rutile from ilmenite using hydrochloric acid leaching is investigated. Previously published data is used to comment on the optimum process conditions. It is shown that the most important aspect to consider is the maximisation of impurity dissolution and the minimisation of titanium losses.

Jan 1, 2001

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By V A. Chanturia, T N. Matveeva, V V. Getman, A Yu Karkeshkina

The development and application of new effective environmentally friendly reagents for the flotation of thin and ultrathin mineral components is an urgent task. The analysis of the nomenclature of chemicals, including flotation reagents and flocculants, showed that water-soluble polymers (WSP) might be used in flotation separation of fine grinding products containing non-ferrous and precious metals. Water-soluble polymers that are responsive to temperature changes are the most attractive as reagents during flotation. These are the thermo-responsive polymers or thermomorphic polymers. The presence of nitrogen and oxygen atoms in the polymer molecule contributes to the formation of a coordination bond with non-ferrous and precious metals. A research conducted at the ICEMR RAS within the framework of the scientific school of Academician of the Russian Academy of Sciences Chanturia helped to develop a method of flotation of finely ground mineral particles containing valuable components using modified thermomorphic polymers. The paper focuses on the experimental study of poly (vinyl caprolactam) (PVC) as a flotation reagent for gold recovery from finely ground mineral products. PVC is a ready-made water-soluble thermosensitive polymer that does not require complex synthesis. PVC has a high ability to form complexes in an aqueous environment when heated. According to experimental data, the polymer interacts with gold nanoparticles, contributing to the extraction of gold from fine mineral products and the tailings that makes it perspective as an additional flotation agent for the processing of gold-containing ores.

Aug 24, 2022

By T Vizcarra, G Sandoval, C L. Evans

One of the challenges in the development of mineral processing simulators is modelling the liberation characteristics of particles produced by comminution circuits. Understanding the mineral characteristics of these particles is one of the keys to predicting their behaviour in separation circuits. While more fundamental research seeks to model the non-random breakage of ores this work examines whether we can move forward now by using observed characteristics of ores to model the composition of particles generated in comminution processes. Several researchers have noted the similarity of the liberation characteristics for a selected size fraction of particulate material, whether the fraction comes from a coarse material, such as the product from a jaw crusher, or a more finely ground material, such as the product from a ball mill. In most cases these observations were reported as an aside and were not the main focus of the published work. This observed behaviour has the potential to be a useful tool for modelling the particle characteristics in mineral comminution and separation circuits, particularly as we move towards the development of multi-component models. However, before the behaviour can be used widely we need to understand which ore types follow the observed pattern and which do not. The current work examines a range of ores and identifies which exhibit the pattern of similarity of composition for particles in a given size class that has been produced as the result of a variety of breakage conditions. The impact of mineralogy and texture on the evolution of liberation characteristics for both valuable and gangue minerals is discussed.

Jan 1, 2008

By Boyd GL

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal rCCOvCrCd h\ hi'eh ss-all mining methods.

Jan 1, 1998

By R Ballantyne, M Adams

Time Usage Models, used as a basis for calculating performance indicators for mobile mining equipment, have developed from very simple to very sophisticated models. This development has paralleled the increased collection and analysis of production data that itself has been enabled by the evolution of underground voice and data communications along with the relevant information systems. A Time Usage Model divides the hours that equipment is (or is not) used into standard components, by a hierarchical breakdown, so that measures of productivity can be used to compare performance of both people and equipment. The calculation of equipment availability, and thus the underlying Time Usage Model, has always been an extremely emotive topic as different groups use time usage information for different purposes. The direct link between measuring performance Key Performance Indicators (KPI) calculated from these models and employee rewards impacts upon the workforce. This paper discusses the conflict in use by various stakeholders and proposes ways to address some of the more contentious issues each supported by case studies. The simple status code functionality used by early systems has proven inadequate, leading to the evolution of “work-arounds”. These workarounds have become the norm and unfortunately have become embedded in the next generation of models and the information systems that incorporate them. This paper contends that the industry should stop building Time Usage Models to accommodate shortcomings in proprietary systems, but rather collaborate with suppliers to develop innovative methods to deal with the fundamental requirements. There are many points of differentiation that are not clear-cut. Pitfalls are discussed as well as threats to success. A framework of rules is developed as guidelines for how a Time Usage Model should be developed and applied. This will hopefully stimulate the on-going discussion as to how Equipment Availability and other components of the model should be calculated.

Mar 15, 2021

By R Grogan

Nautilus Minerals Inc is a sea floor resource exploration and development company focused on developing the Solwara 1 Project, a copper-gold sea floor massive sulfide deposit in the territorial waters of Papua New Guinea, for which it holds a mining lease and associated environment permit.Economies depend upon four key types of capital: built, natural, financial and human. Natural capital consists of the ‘minerals, energy, plants, animals, ecosystems (climatic processes, nutrient cycles and other natural structures and systems) found on Earth that provide a flow of natural goods and services’ (Daly and Farley, 2004). Many ecosystem goods such as fish, fruit and water are already valued and sold in markets; however, some ecosystem services are not amenable to markets and have remained unvalued in traditional accounting methods, even though they provide significant value (such as flood protection, climate stability etc; Batker and Schmidt, 2015).There are now economic methods available to quantify and value natural capital and many non-market ecosystem services. When valued in dollars, these services can be incorporated into a number of economic tools, including benefit-cost analysis, accounting, environmental impact statements, asset management plans and rate of return on investment calculations. Their inclusion ultimately strengthens decision-making. When natural capital assets and ecosystem services are not considered in economic analysis, they are effectively valued at zero. This omission can lead to poor decisions, inefficient capital investments, higher incurred costs and losses due to unexpected events (Batker and Schmidt, 2015).In 2015 Earth Economics was commissioned by Nautilus Minerals Inc to conduct an independent, objective environmental and social benchmarking analysis of the proposed deep seabed Solwara 1 mine with terrestrial copper mines (referred to as ‘the report’). The report represents the first ever natural capital accounting and ecosystem goods and services framework for seabed mining.The report compares the proposed Solwara 1 mine with three terrestrial mines: Bingham Canyon (Utah, USA), Prominent Hill (South Australia, Australia), and Intag (a proposed mine in Intag Province, Ecuador), and provides a natural capital accounting assessment for all four operations.CITATION:Grogan, R, 2016. Natural capital accounting – a sea floor mining application, in Proceedings Life-of-Mine 2016 Conference, pp 2–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

It is hypothesised that increasing the number of loading passes will produce a reduced range of truck payload outcomes compared with four-pass loading. The paper provides analysis to support this hypothesis. It is shown that, hypothetically, loading trucks with five or more passes will result in reduced tendency for overloading and reduced confidence interval for truck payloads that increase the confidence level of containing high end payloads within safe and commercially acceptable limits. Furthermore, increased number of passes provides for more precise bucket load spotting and so improves distribution of payloads within truck bodies. Truck-loading issues examined by the paper include: Improvement in life of driveline components and tyres. Generally tyre costs are relatively moderate; but tyres tend to become an increasingly sensitive performance/cost component as truck scale increases; Reduction of site severity fects flowing on to suspensions, truck frames and structural components generally with potential for reduced long-term repair costs; Less physical body damage due to smaller load increments; Reduced risk of non-compliance with payload limitations for safe braking standards; Increase in loading cycle times tend to increase with scale of loading machinery within the limits of a specific type of equipment (ie rope shovels or hydraulic shovels). Production increase with increased bucket capacity is, to a degree, offset by slower loading cycle times. This is particularly pronounced with front-end loaders but tends to be less noticeable with hydraulic excavators/shovels and electric rope shovels. Decrease in loading time, as a proportion of total truck-cycle time as open pits deepen and dump reaches increase. The production and cost benefits of four-pass loading tend to diminish as truck cycle times increase. The paper also discusses the implications for loading-equipment philosophy to satisfy the future needs of the industry. Cost benefits from upscaling tend to diminish as truck scale increases, so increasing management diligence and close monitoring are required to ensure that expected outcomes are realised. These truck-loading issues have been researched to assess the benefits positive or negative) of four-pass loading in practical scenarios. An attempt is made to determine whether four-pass loading is a æmust-haveÆ or merely a æmythÆ.

Jan 1, 2003

The 5.6 km Canning Tunnel was constructed to improve water supply from Canning Dam to the Perth metropolitan area. The site area is in the Darling Range which is essentially a laterite-capped plateau-remnant underlain by Archaean granitic rocks, intruded by dolerite. Two arrangements were available. After geotechnical investigations which included geological mapping, seismic refraction geo- physics, diamond drilling and mechanical rock testing, a single tunnel was selected in pre- ference to two short tunnels and a connecting pipeline. The tunnel is hydraulically equivalent to a fully lined tunnel 1.83 m in diameter and 5 580 m long. The alignment diverged from a straight line so that the initial upstream section was almost normal to the contours which allowed for minimal support requirements in a weathered zone. Although steel and con- crete lining was needed at both ends, the main section of the tunnel was unlined except for a concrete floor. A sand and rock trap with a capacity of 46 m3 was constructed near the outlet portal to collect debris and sand down to a size of about 2 mm. Portal excavations were in highly to completely weathered rock which extended 56 m into the tunnel at the upstream end, and 18 m at the downstream end. Conventional drilling and blasting were used for tunnel excavation with survey control by laser. Breakage lEngineering Geologist, Mines Department, Perth, W.A.

Jan 1, 1976

By A Creighton, C McKenzie

Blasting is a critical task in the development of an open pit. The formation of stable slopes is also essential to the safe and economic extraction of ore. The objectives of a mine blasting department are often considered to be in direct conflict with those of the geotechnical department. This should not be the case. Personnel in the various mining departments need to understand that their goals are the same û to optimise safety and cost-effectiveness of the operation. Blasting has the potential to damage rock that is to remain in situ by generating either excess vibration, and/or pressure. These damage mechanisms are described and guidelines with respect to blast design to minimise the potential for damage are given. A rock mass could be expected to be subjected to varying degrees of damage by blasting, including both intensity of damage and also the extent of damage. These issues have potential to impact significantly on geotechnical design considerations. It is therefore important for the practitioner to define what constitutes damage. In the context of mining, it is recognised that there is a need to balance the requirements for efficient excavation with those of forming stable and cost-effective pit walls. It is therefore important to have a set of key performance indicators (KPIs) against which the performance can be bench marked. These would include cost and time, both of which may be influenced by very diverse factors such as drilling, explosives and their performance, fragmentation, excavator and haul truck performance, requirements for batter clean-up and safe working practices. KPIs are identified and discussed in this paper.

Jan 1, 2003

By G Davison, C Rossimel, M Bouazza

Expanding rock bolts anchor within a rock mass more efficiently than non-expanding varieties. This is of great importance in weak ground conditions, where grouted friction bolts perform less efficiently than in good ground conditions. Filling a Split Set with demolition concrete has been shown to double the load-carrying capacity when compared to conventional use of Split Sets. This report details verification of these results by installing and pull-testing 14 Split Sets of varying grout conditions within in a fault zone. These Expanding Split Sets achieved loads double and triple that of ungrouted and normally grouted conventional Split Sets. A literature review and chemical analysis were conducted to understand the expansion process better. It was found that 20 per cent more calcium is included in expanding cement, which is responsible for its growth. Factors most affecting the expansion process were identified. Furthermore, the expansion rate of a bolt outside a borehole was measured and 6 mm of expansion across its diameter was found. The compressive properties of the cement were compared with other types, due to expanding cement becoming uncohesive after the expansion process is complete. When confined within a Split Set, compression testing demonstrated that this grout is just as strong and rigid as normal grout. Finally, the bolts were tested by shear and it was found that the Expanding Split Set (ESS) has a similar shear capacity to grouted Split Sets, which is 70 per cent higher than that of ungrouted Split Sets. These results enabled the mechanism for improved performance in weak ground conditions to be verified. Expanding grout will expand the Split Set into its borehole of varying diameter and lock it into place, creating increased friction and resistance to pull-out. This paper shows that ESSs can be a useful reinforcement technique in weak ground conditions.CITATION:Rossimel, C, Davison, G and Bouazza, M, 2014. An investigation of expanding split sets in weak ground, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 159–170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J H. Park, M J. Lee

Because the environmental problems are occurred by greenhouse gases such as CO2, the industries have tried to increase electric motor efficiency to reduce CO2 emissions. A core material of electric motor is high-silicon electrical steel. The ferrosilicon (FeSi) alloy, a raw material for the production of electrical steel, affects the electric properties of silicon steel. The main impurities such as Ca, Al and Ti make inclusions or precipitates that causes core loss. The slag treatment has been widely used to remove impurity elements. Thermodynamic principles for the refining of several impurities, specifically Ca and Al, have been investigated, whereas thermodynamic behaviour of Ti has not been fully understood yet. Therefore, in the present study, the titanium distribution ratio () between ferrosilicon and CaO-SiO2-Al2O3 slag system at 1773 K was investigated. The results show that is influenced by both the basicity and stability of titanium ion in the slag. Specifically, exhibits a minimum value at about C/S=0.7 indicating a shift in the titanate structure unit from [TiO5]-square pyramid to [TiO4]-tetrahedron because of lack of Ca2+ ions in a C/S<0.8 region, contributing to an increase in titanate capacity and .

Jun 19, 2024

By M Hassall, E Humphries

Personal risk assessment processes, also known as Take 5 or SLAM (Stop, Look, Assess, Manage) have been utilised in high hazard industries for over 30 years. However, there is limited research to understand if a personal risk assessment process improves safety and health outcomes. The author’s learnings during discussions with training participants in G3/G-MIRM (Risk Management Systems) and G2 (Risk Assessment for Supervisors) courses have provided them with significant insight into understanding if a personal risk assessment process is valued across a number of mining industry organisations. These discussions arise when the four-layer model is presented (Figure 1) where ‘Layer 4’ represents the last resort risk checking activity. In this context, training participants agree that this process has value. However, the consistent opinion is that the personal risk assessment process is not effective, that it is a ‘tick and flick exercise’ and is not achieving the desired outcomes.

Apr 16, 2024

By G McCullough, B Mutsaers, J Jessop

"*This is an abstract only* Geometallurgical initiatives have demonstrated considerable value to operations that have trialled them. However, it is extremely difficult for these initiatives to become properly embedded into the operations and for that value to be realised on an ongoing basis.This paper will explore some of the historical reasons why this is the case. Some of these reasons include the limited tools available to manage an integrated operation. These, in turn, have resulted from poor communications infrastructure, inadequate sensor capability and the way technical mining software has evolved over the last 30 years.This paper will then investigate how the evolution of technology in recent years can help overcome these constraints and compare progress with similar industries.CITATION:McCullough, G, Mutsaers, B and Jessop, J, 2013. Obstacles to embedding geometallurgy decision-making into operations and how to increase maturity of this critical capability, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 139-140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By D A. Sims

This paper outlines the contributing factors to a series of erroneous Mineral Resource estimates which led to considerable loss, including significant reduction of mine life and consequently a large write-down of asset value. The error prompted divestment of the mineral asset in the short-term by the owners, a major mining company. There were multiple and complex contributions to the result: • The mine was undergoing a transition in the deposit geology with increasing depth that was not accommodated in the models. Early indications of the geological transition in initial drilling were generally unrecognised in resource modelling. The shortcomings of the models became apparent with increasing infill drilling and subsequent production reconciliation. • There was a lack of recognition of, and confidence in, site-based input and skills by corporate technical management. The site had a reputation internally for over-delivery to plan early in its life and that supported the anticipation of ongoing metal delivery into the mine plan by management. • A corporate lack of confidence in site being able to adequately domain the mineralisation led to the use of a CIK domaining process, rather than one which was geologically based. This domaining process led to gross over-statement of mineralisation trends reflected in the subsequent OK estimate. • Timelines on the outsourced estimation process were so short that validation was not possible. Obvious errors in the estimate versus data were not able to be used to correct the issues and the site’s Competent Person sign-off occurred without adequate checks. This case study is presented to reinforce the concept that Mineral Resource estimates are not solely based on the ability of the Competent Person to satisfactorily guide the process. There are usually multiple complex issues in the estimation process which need to be recognised and considered in judging reconciliations of model to actual.

May 24, 2023

By T Mizuta, T Nakano, D Ishiyama

The Tamagawa Hot Spring, from which Ra-Pb-Sr-bearing barite precipitates, is a representative hot spring in a volcanic gas-bearing hydrothermal system associated with Quaternary andesitic to dacitic magmatic activity beneath the Yakeyama Volcano. Thermal water in the Tamagawa Hot Spring is divided into three types: Cl-SO4-type (Ohbuki hot spring: pH 1.2); SO4-type (pH 1.8 to 2.9); and neutral-type (pH 6.1). The concentrations of dissolved components in the Ohbuki Cl-SO4-type thermal water are about ten times higher than in the SO4-type thermal water. The 87Sr/86Sr isotopic signatures of the Ohbuki Cl-SO4-type thermal waters (0.703992 ¦ 0.000004 to 0.704032 ¦ 0.000006) are different from those of SO4-type thermal waters (0.704245 ¦ 0.000003) formed by the interaction of andesitic volcanic rocks (0.704065 ¦ 0.000007 to 0.704093 ¦ 0.000009) and groundwater derived from river water (0.704314 ¦ 0.000012 to 0.704519 ¦ 0.000013) in a shallower part of the hot spring area. The possible origins of Sr in the Ohbuki Cl-SO4-type thermal water and in the SO4-type thermal water are different. The Sr isotopic ratios (0.704130 ¦ 0.000012 to 0.707556 ¦ 0.000014) of Aniai Formation andPreYakeyama Lake deposits occurring below the hot spring area are distinctly higher than those of the Cl-SO4-type thermal water. However, it is expected that a solidifying andesitic or dacitic magma which has similar Sr isotopic ratios of the Ohbuki Cl-SO4-type thermal water, occur in the deep portion of the Tamagawa Hot Spring. The Cl-SO4-type thermal waters having low Sr isotopic ratios do not acquire their Sr isotopic signatures by interaction with strata below the hot spring area, but they are likely to reflect water interaction with a solidifying magma with low Sr isotopic ratios. Components including rare metals in Cl-SO4 type thermal water could be transported from a deeper part. An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By J Lombardi

OZ Minerals&apos; Prominent Hill copper-gold concentrator is located 130 kilometres south east of the town of Coober Pedy in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 9.6Mtpa ore throughput capacity. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell heading up the three stage conventional cell cleaner circuit. In total there are four level controllers in the rougher train and ten level controllers in the cleaning circuit for eighteen cells.Generic proportional – integral and derivative (PID) control used on the level controllers alone propagated any disturbances downstream in the circuit that were generated from the grinding circuit, hoppers, between cells and interconnected banks of cells, having a negative impact on plant performance. To better control such disturbances, FloatStar level stabiliser was selected for installation on the flotation circuit to account for the interaction between the cells. Multivariable control was also installed on the five concentrate hoppers to maintain consistent feed to the cells and to the IsaMill. An additional area identified for optimisation in the flotation circuit was the mass pull rate from the rougher cells. FloatStar flow optimiser was selected to be installed subsequent to the FloatStar level stabiliser. This allowed for a unified, consistent and optimal approach to running the rougher circuit. This paper describes the improvement in the stabilisation of the circuit achieved by the FloatStar level stabiliser by using the interaction matrix between cell level controllers and the results and benefits of implementing the FloatStar flow optimiser on the rougher train.

Aug 8, 2011

By J Maxlow, M J. Woods, M P. Sandy

The Newcrest Mining Limited Telfer operation comprises both open pit and underground operations producing gold and copper. The underground operation is made up of three production areas, the sublevel cave (SLC), M Reefs narrow vein open stoping and Western longhole open stoping areas. With stoping situated on the abutments of a mature and active sublevel cave, the interaction between mining areas is often complex. This is particularly evident in the M Reefs orebodies with high levels of extraction in all four reefs, and reliance on pillars to maintain local and global stability. A key concern was the potential for a cascading pillar failure to develop and rapidly progress through the M Reefs stoping area. The monitoring plan needed to capture any change in overall stability and identify if deformation was caused by pillar failure within the M Reefs and hanging wall closure, or shear on the reefs caused by SLC influence.

Nov 29, 2022