Search Documents

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975

By Shuguang L, Jing S

Computer controlled truck dispatching systems is a newly-developed technical system in surface mines with shovel-truck technology. The real time dispatching criteria, as the core of optimal truck dispatching software, are analysed and a new criterion, complex dispatching criterion, is put forward. Dispatching criteria previously proposed include: 1. `Earliest Loading' (EL) - to assign a truck to the shovel at which the truck can be loaded earliest. 2. `Max Truck' (MT) - to assign a truck to the shovel at which the truck will have the shortest waiting time. 3. `Max Shovel' (MS) - to assign a truck to the shovel which has been waiting for the longest time. 4. `Minimum Saturation Degree' (MSD) - to assign a truck to the shovel at the branch where the truck flow saturation degree is minimum. 5. `Minimum Saturation Degree with Truck Cycle time consideration' (MSDTC) - as the MSD principle, with the truck travel cycle also considered. 6. `Fixed Dispatching' (FIX) - to assign trucks to fixed shovels. A system simulation model has been set up for truck dispatching system analysis. A few surface coal mines have been selected for case studies. Equipment waiting times and shift production of the system are obtained as the main outputs of the model. Simulation results show that each dispatching criterion has its own applicable range, no one can absolutely dominate the others. For example, when under-trucked, EL and MT criterion can obtain higher production than the MS criterion; when over-trucked, it is vice versa; while for MSD criteria, better results can be obtained no matter how the truck numbers fluctuate. From the view point of shovel output balance, large fluctuations occur for EL and MT criteria, while a good balance can be obtained for other criteria. In the light of dynamic change of mining system conditions, a single dispatching criterion is not necessarily reasonable. A complex dispatching criterion has been put forward to seek the complex optimum effect. Taking the advantage of each dispatching criteria, the dispatching result of a complex dispatching criterion dominates over individual dispatching criterion and a comprehensive optimum effect can be reached.

Jan 1, 1995

By Fulton E, Ring RJ, Waters DJ

Laboratory leach tests of Nabarlek uranium ore carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's Acid1 (permonosulphuric acid) as an alternative oxident to pyrolusite indicated reduced acid consumption in leaching and lime savings in neutralisation of tailings liquors when using Caro's Acid. Interox Chemicals Pty. Ltd. arranged a plant trial for Caro's Acid at Queensland Mines Nabarlek Plant. The trial confirmed that significant savings in acid and lime can be achieved under plant conditions. Plant operations also demonstrated improved redox potential control was possible using Caro's Acid.

Jan 1, 1978

The reasons for selecting two stage pebble milling in preference to conventional methods of grinding are discussed. Commissioning of the first section was completed in October, 1969. Improvements in both the operating and engineering aspects were then incorporated in the section commiss ioned in March, 1971.

Jan 1, 1975

The goal of the Bureau of Mines, U. S. De- partment of the Interior, diesel engine research program is to reduce exhaust emissions and mini- mize the risk of fires and explosions caused by the use of diesel-powered equipment in under- ground mines. Significant results of research conducted during the last 5 years are briefly described, with references to published reports on specific topics. Topics covered here include brief discussions of a newly completed diesel research laboratory, the effects of a fuel addi- tive on diesel exhaust particulate matter, the effect of diesel engine maintenance on emis- sions, a diesel particulate filter for equipment used in underground metal and nonmetal, and coal mines, and lastly, the prototype hydrogen- powered mine vehicle. These research accomplishments could favor- ably affect the mining industry by reducing the health and safety hazards associated with the use of diesel-powered equipment in underground Mines.

Jan 1, 1988

The first continuous pressure disk filter took up industrial-scale operation in Germany in 1976. This paper comments on major components of pressure filter facilities from the point of view of industrial-plant suppliers. For lack of time aspects of economy have not been commented upon. The paper elucidates a number of process-engineering inter-relations. It outlines important development trends from the angle of a machine-building company.

Jan 1, 1989

By Hannan JC

Consent to develop and operate a new coal mine in New South Wales (NSW) will be conditional upon a number of environmental controls. In NSW, applications for any new major development associated with coal mining are determined by the Minister for Planning and Environment. The environ- mental conditions placed on the development consent, the coal mining lease and the approvals, and licences under the pollution control legislation amount to a substantial component of any new project's commissioning considerations. The nature, scale and location of projects and the principles of pollution control on which conditions of State Pollution Control Commission (SPCC) approvals are based have a considerable influence on project planning. The design, construction and operation of coal mines in NSW has been progressively modified over the past 15 years, to incorporate increasingly stringent requirements for environmental management. These requirements are in turn, a reflection of a greater community demand for environmental protection.

Jan 1, 1986

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs.A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanized mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximized, cost if reduced and all profit opportunities are optimized. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

By Takagi T, Seetharam R, Sie SH, Naito K

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medical/high-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnSZ), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995

'Industrial Minerals - their mining and use in New Zealand' is the theme of the 1978 Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy. This paper describes the use of phosphate rock, sulphur and potassium chloride (potash) - three industrial minerals which have enabled the farmers of New Zealand to increase production to current levels. The growth of imports of these raw materials for the New Zealand fertiliser industry is well documented in NZ Fertiliser Statistics 1977. This is the most recent of the Ministry of Agriculture and Fisheries annual publications on this Subject prepared from the detailed returns of fertiliser manufacture and sales from each fertiliser works. There are now 12 of these works in New Zealand one of the most recently established being in Whangarie where this conference is being held. Its capacity to manufacture superphosphate will shortly be 300 000 tonnes twice that when it opened late in 1964. New grinding and manufacturing equipment comes on stream early in 1979. This paper illustrates the interdependence of two primary industries, agriculture and mining. New Zealand's economy in the foreseeable future will be based on agriculture so that our standard of living is dependent on the overseas prices and freight costs of the bulk raw materials from which our fertilisers are made. For the year ended 31 March 1978 New Zealand's total exports were $3395 million, of this total $2413 million (71%) came from the products of pastoral agriculture (wheat, wool, dairy and other animal products), $291 million from forest products and $501 (15%) from manufactured exports. Approximately half of the pastoral receipts can be attributed to the fertilisers applied at a total cost of about $200 million including subsidy.

Jan 1, 1978

By M Olsson, I Bergqvist

A Swedish table of blast damage depths has, in one form or other, been in use since the late-1970s. Its history and the underlying theory are described. New experimental and theoretical findings that point out a number of shortcomings in the table and the underlying theory are presented and discussed. A revised version of the blast damage table was recently introduced in conjunction with new but incomplete recommendations for cautious perimeter blasting. The new table leaves the difficult task of taking into account factors like decoupling, water in the borehole, the rock properties, type of initiation, charge length and the actual bit diameter to the user. This paper discusses different ways of doing this, based on the experimental findings and a recent formula for the prediction of the lengths of radial cracks behind the half-casts. The material presented in this paper is meant to supplement and extend the new Swedish recommendations for cautious perimeter blasting of tunnels, shafts, pits and road cuts.

Jan 1, 2001

Within the Ross River Basin, the following types of water were collected and analysed; 19 streams, 24 wells and bores together with 19 samples from the Ross River Dam. The waters were found to contain up to 269 ppm of silica and, although they meet the requirements for industry in all other respects, this extremely high figure means that two basic guidelines should be followed. All steam generation units, except those less than 150 psi should employ hot lime zeolite softening, demineralization or evaporation to remove silica. Cooling systems should only operate on a once through basis.

Jan 1, 1978

By Sorentino C

Mineral valuation may appear to be a special field of financial valuation when in fact it is a subset of general investment decision theory. The only significant difference in mineral valuation is that in the case of valuing an on-going mineral asset, ie a mine, often there is no initial capital outlay involved. One is required to determine what the mineral asset as it stands is worth. But this is the same problem as determining the maximum one could pay today and not incur a loss over the life of the asset. In other words one needs to determine the Net Present Value (NPV) of the asset. The two most widely used discounted cash flow methods, NPV and Internal Rate of Return (IRR) came of age with the rapid adoption of the personal computer and spreadsheet programs. The two methods are directly related as the IRR is a special case of NPV. NPV measures the absolute increase in real wealth that can be expected from a certain investment, which makes it particularly suitable for mineral asset valuation, but ignores the efficiency of the investment. In contrast, IRR gives the expected efficiency of the investment but ignores the increase in wealth aspect. IRR has two serious theoretical weaknesses; multiple IRR's and a very rigid assumption about the rate of return of reinvested proceeds, plus if no initial equity expenditure is involved there is no IRR. The choice of the ""hurdle"" rate can also be a problem and in certain circumstances one can obtain different rankings of mutually exclusive projects using IRR and NPV. Although NPV and IRR supposedly measure financial risk, in fact they only address a very narrow area of risk, namely the time value of money given the real discount rate. They side step the issue of what the real discount rate should be and varying degrees of risk. The classical way to establish the real discount rate is to use the weighted average cost of capital.

Jan 1, 1994

The theme at this yearÆs AusIMM New Leaders Conference in Ballarat was æThe Minerals Industry û Future Directions for New LeadersÆ. There was a strong focus on the recruitment and retention of trained and skilled graduates and new professionals into the mining profession. This paper highlights some of the key findings and discussion points from the New Leaders Conference. While some of the main causes of the decline in attracting new geoscientists to the mining industry have been identified, there still remains a lack of accountability among a number of Australian mining companies. Some of the factors identified that are driving new graduates away from the industry include; the social and geographical isolation, the long hours in challenging conditions and a difficulty in obtaining work straight out of University. Often there appears to be no clear opportunities within companies for career development and advancement. The opinion also still persists that the mining industry is lagging behind in both environmental and technical developments, which makes entry to the industry unattractive. Solutions that some of the large players in the Australian mining industry are implementing to help reverse the trend include targeted marketing of the lifestyle, money, freedom and travel offered in the mining industry, the development of graduate recruitment programmes and much more emphasis on the quality and reputation of the companies themselves. Incentives to attract families have also been significant in attracting and retaining employees whom otherwise would have left the workforce. However, more still needs to be done to completely reverse this trend and the mining industry needs to continue to be proactive in marketing itself as a desirable employer and career choice option for students and new professionals.

Jan 1, 2004

This paper discusses a number of examples of how environmental factors have been incorporated into the water management aspects of mining projects. One example is the Kingston Lignite Project in the South-East of South Australia where the most significant environmental issue was considered to be the effect of drawdown from mine dewatering and depressurization upon the use of groundwater. By proposing an alternative mining method - the use of floating dredges rather than a two-pass dragline method - drawdown effects would no longer be a concern. A second example is the Pine Creek Gold Mine in the Northern Territory. In this case the principal area of interest from an environmental viewpoint was water management - in particular effluent disposal, contaminated seepage from overburden and tailings, and project water supply. Through an integrated approach to the management of wastes and water the potential for water quality impairment was significantly reduced and external water supply requirements were also significantly reduced.

Jan 1, 1987

By Salmon P. T, Gilmour R

Commercial production of zinc started at the Pasminco Metals - EZ Plant, Hobart, Tasmania, in 1921. Since that time the capacity of the plant has been steadily increased to its present level of almost 220 000 tpa. Major areas of the plant have been successively upgraded over a number of years, (Roasters, 1969, 1975; Acid Plants, 1981; Casting, 1972; Residue Treatment Plant, 1971), but, until recently, the leach/purification area remained virtually unchanged from the time the plant was built. The major redevelopment of the hydrometallurgical plant began with fully integrated pilot plant testing of the proposed new circuit in 1981. The pilot plant incorporated the Low-contaminant Jarosite Process, and a new two-stage zinc dust purification procedure. In 1985, approval was granted for a major modemisation program which involved the complete replacement of most of the leaching and purification plants, and substantial improvements to the residue treatment plant. Construction of the first of the new plant sections, Strong Acid Leaching, commenced in 1986. This paper describes briefly the modernisation program itself, and the current method of zinc production at the PMEZ plant. The new plant sections comprise a Strong Acid Leach stage to improve lead residue grade; a Preneutralisation stage to reduce metal losses in jarosite; new filtration stages for both jarosite and lead residue; new Neutral Leach and Weak Acid Leach stages to replace old equipment; a new Solution Purification stage to replace the use of organic reagents to remove cobalt; and a new Gypsum Removal stage to cool the solution before electrolysis. At the completion of the modernisation program, only the electrolytic cellhouse remains of the early plant sections.

Jan 1, 1993

By Tapp B. A

To date, few studies have been made regarding the energy requirements of the Australian mining and mineral processing industries. This paper indicates that these industries use a substantial proportion of the total Australian energy input (32.7% in 1971-72 and 36.10% in 1974-75). With the growth orientation of these industries, this input is likely to increase. Data shows that mining energy requirementE varied from 4.22% (of total Australian energy requirements) in 1971-72 to 4.16% in 1974-75. Energy requirements for the total mineral processing industries increased from 28.49% to 31.93% for the same period. The total estimated primary energy input varied from 22.56% to 25.2%, whilst indirect energy use, in the form of electricity increased from 10.16% to 10.66%; in the same period. Analysis of primary energy input data within the processing industries (1973/4) showed that the Iron and Steel Industry consumed 15.03% of the Australian total consumption, Non-Ferrous metals, 5.43%, Cement, 1.64%, and Refractories, 1.59%. In toto this represented 24.57% of the total

Jan 1, 1979

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

Good morning. I am very pleased to be invited to present the Opening Address to this inaugural New Zealand Minerals & Mining Conference. It is indeed a pleasure to see so many representatives of this industry, which is so important to New Zealand's economy, present here today.   I extend a warm welcome to all delegates, particularly those from outside New Zealand. To those of you who have travelled from offshore, please closely observe our industry, and do not hesitate to ask Crown Minerals staff here for any further information you may want. I trust you will soon come to the same conclusion that my two following speakers have; that New Zealand is a good investment destination, and further that many of you will decide to invest in New Zealand's minerals and mining industry.   In New Zealand the minerals industry - minerals, coal and petroleum - together constitute an approximate $2.5 billion per year business. In broad terms this is about 3% of our Gross Domestic Product.

Jan 1, 1997

By Dudgeon RN, Houston ML

When the original Mount Gunson joint venture,between CSR Limited and United Uranium N.L. ceased operations in December 1971, an intensive exploration campaign was launched to prospect for more ore in the Mount Gunson region. This campaign resulted in the dis- covery'of the Cattle Grid copper deposit. A comprehensive sampling pro- gramme including the sinking of over 200 diamond drill holes and two vertical shafts,proved the existence of 4.6 million tonnes of ore, at a mean grade of 2.4% Cu,calculated at 1.00% Cu cutoff.

Jan 1, 1975