Search Documents

By K L. Brown

The concentrations of trace metals in deep hydrothermal solutions (~1 km depth, 200 to >300¦C) from modern hydrothermal systems in the Taupo Volcanic Zone, New Zealand, and Ladolam, Lihir Island, Papua New Guinea were obtained using a purpose-built downhole fluid sampler and ICP-MS analyses. The results range widely: gold (<0.1 - 23 ppb); silver (<3 - 2400 ppb); arsenic (100 - 18 000 ppm); antimony (2 - 1200 ppm); mercury (<1 - 78 ppb) and provide the basis for quantifying the flux and fate of metals as well as assessing their sources (Simmons and Brown, 2006, 2007). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

And it takes more than good organisation. You may read or heard this poignant reflection: We tried hard, but it seemed that every time we were beginning to form up in teams we would be reorganised. I was to learn later in life that we tend to meet any new situation by re-organising, and a wonderful method this is for creating the illusion of progress while producing confusion, inefficiency, and demoralisation This was written by the Roman Gaius Petronius in AD65. How much have things changed in nearly 2,000 years? What then does it take besides the fundamentals and good organisation to build a successful career in a successful organisation? I'm prepared to venture a list of what I'll'call Tips for Young Professionals. If you've got what it takes, and apply these, I think that you'll gain a great deal of satisfaction from your career, even if you don't reach the distant target each of you should have in mind now. So settle back in an advice-receiving mode, and please forgive me if I come across as a master of the bleedin' obvious, as Basil once accused his wife Sybil of being in the unforgettable Fawlty Towers.

Jan 1, 1990

By Wilkinson RDB, Van Der Meer FP

In order to overcome the statistical limitations imposed by the need to recover density tracers by hand, magnetic density tracers were developed to determine the efficiency of dense medium separators treating porous materials. The tracers were manufactured by extrusion of polypropylene ferrosilicon mixtures and subsequently coated with a distinctive paint to allow hand sorting according to density. Fifteen tracer batches were manufactured in the range 1.61 - 1.94 g/cm3. The tracer densities were determined by a hydrostatic method. The tracer method was applied to the dense medium separation of a Moroccan oil shale in a pilot scale Dyna Whirlpool separator. For each test, about 20,000 tracers were added with the plant feed and subsequently recovered from the products with a dry low intensity magnetic separator. The Tromp curve determined by conventional heavy liquid analysis was displaced towards lower densities compared with that determined by tracers, indicating that the porous shale particles absorb heavy liquid. It is concluded that for porous materials like oil shale and coal, the tracer method gives the most accurate results. In pilot scale testwork the tracer method is also much faster than the conventional heavy liquid analysis, as rather large samples have to be processed by the latter method to ensure Representativeness.

Jan 1, 1987

The proportion of coal production from underground operations in Queensland, is likely to increase in the future. A portion of this increase will come from mines working under farming areas. The degree of compatibility between underground coal mining operations and farming is examined. Two case histories are considered in detail. These relate to farming areas in the Moura and Emerald districts. Mining the Moura, area has been undertaken for the last two and half decades, while in the Emerald area, large scale underground coal mining is currently being planned. Interference to watercourses and water harvesting programmes, damage to crops, and ponding in cultivated areas have been experienced in mining areas. With expansion of underground mining in farming areas, the principle areas of likely conflict are the effects of surface subsidence on irrigation and erosion control structures. Other potential problems that may arise in particular circumstances include reduction in availability of water for harvesting, pollution, surface cracking and damage to surface structures. Finely textured soils and erratic and violent rainfall patterns make farming in central Queensland particularly vulnerable to severe soil erosion unless strict precautions are taken. Soil erosion control is an essential part of farming. Contour banks are used to ensure that runoff velocities are suitably low. Where steep slopes are encountered, grassing is the most effective way to prevent erosion.

Jan 1, 1987

By S Wasi, J Tobiczyk, J Roszkowski

Methane and fire hazards have a vital effect on work safety and continuity of mining plant operation. In the 1990s, the SMP hazards monitoring and ventilation control systems, based on continuous measurement of air parameters, were put into operation at nearly 30 Polish mines. These systems provide continuous measurement of methane concentration within the range of zero to 100 per cent with automatic switching off of electrical energy immediately after detection of potentially explosive conditions. Early detection of coal spontaneous combustion and open fires is made by continuous measurements of CO, CO2, smoke and O2 content in mine air as well as temperature changes in air and rock mass. The essence of the system is intrinsic safety of all underground instrumentation and uninterrupted central power supply from the surface. All abnormal and critical states are signalled to the mine control room. These trigger alarm and emergency procedures. The computer based ventilation monitoring and control system also performs the function of an expert system for fire detection and underground fire fighting. The mine control operator (dispatcher) makes use of stored data in computer escape route schemes and procedures for the safe withdrawal of miners from hazardous areas. The operator can put in motion intrinsically safe alarm signalling units and banners with programmed messages indicating escape routes.

Jan 1, 2005

Over the past 15 years many world-class gold discoveries have been made in the region. Some deposits, such as Lihir and Porgera in P.N.G., have a contained gold resource that places them among the top dozen deposits ever found on a worldwide basis. Can we see any pattern to these discoveries, or are they the result of good luck or chance by geologists and prospectors who struck it rich? Whilst such discoveries were a feature of the gold rushes of the 1850s and the 1900s, the present boom is now scientifically based. This paper develops an argument that long-tent, multi-disciplinary exploration by experienced geoscience teams underlie the successes achieved. Dis- coveries nearly always reflect a combination of skills, drawn from the areas of geology, geochemistry, geophysics and remote sensing, and a team approach. They do not represent the chance finds of a prospector's pick or such as the Norseman discovery where the gold reef was first noted by the prospector when his horse fell over the outcrop. The following deposits provide major examples of exploration successes within the Australian-Pacific region, it is not an exhaustive list and I have noted other significant producers at the end of this paper. For the Australian mines listed and based on our estimates for 1990 gold production, they represent about 20 per cent of the Australian production total.

Jan 1, 1991

By K Kuganathan

This paper describes a new methodology that can be applied to compare several bench extraction strategies requiring backfill. The method is applicable at the planning or operational stages and can be used to maintain dilution within design parameters and improve the overall economics of bench stoping operations. The parameters influencing bench performance have been empirically rated based on economical, geomechanical, operational and backfill properties. Four different extraction strategies have been considered and rated from most preferred to less preferred using an integrated approach to bench extraction.

Jan 1, 1998

By B C. Povey

HPGR technology has been used at a number of magnetite mines in the world and have significant energy advantages over SAG and AG technologies. The early design at Los Colorados in Chile has been in operation for more than 12 years - and operates very successfully though only reduces the feed size to -5mmThe Whyalla project magnet design pushed the concept to produce a preconcentrate of 80%-350micron - a significant reduction on previous plants though with some wear problems in the early years. The Karara design backpedalled slightly and will only crush to 80%-1.8mm.However, the design issues of using a HPGR to further reduce the feed size continue to be explored. The aim is to reduce the process risks associated with wear and also to reduce the complexity of the downstream process - with consequent benefits in terms of capital and operating costs.The designs are being developed for a couple of projects - one planned to produce 20Mtpa of concentrate with the potential to not only remove SAG and AG milling but also ball milling. The concept is to use multiple passing through the HPGR since, on the data available, the efficiency of the HPGR to reduce size does not significantly diminish as the feed size is reduce. This can be have benefits in both capital and operating cost.CITATION:Povey, B C, 2013. Pushing the use of high pressure grinding rolls in magnetite circuits, in Proceedings MetPlant 2013 , pp 176-189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By A Kindred

The Bogong Hydropower Development is a 140 MW high head power project currently under construction in Northern Victoria. The project is the final link in the Kiewa hydroelectricity scheme, which was originally constructed in the 1950s. Due to its location in the Alpine National Park, the waterway for the Bogong project must be located entirely underground. A series of shafts and tunnels is being constructed to transfer the water from the headworks at McKay Creek to the new power station located on the shores of Lake Guy in Bogong village. The difference in elevation between the headworks and the power station is greater than 420 m, which poses particular issues for the design and construction of the waterway. The purpose of this paper is to describe the design and construction planning aspects of the tunnelling and shaft excavation and lining works for the waterway. The tunnelling works includes 5.7 km of hard rock tunnel boring machine (TBM) driven tunnel, 1.1 km of drill and blast tunnel and two deep shafts. The tunnels and shafts are lined with a mixture of permanent rock bolts and shotcrete, concrete lining and steel lining. The viability of the Bogong Hydropower Development relies heavily on the ability of the TBM to excavate at high speed through the East Kiewa Grandiorites. Particular attention was given during the construction planning stage to understanding the excavation characteristics of this material, and designing a suitable hard rock TBM that would be capable of meeting the program requirements of the project.

Jan 1, 2008

By M Pizey

After 60 years of operation, coal extraction at Solid Energy New ZealandÆs (SENZ) Strongman Mine, near Rapahoe is scheduled to end in early 2005. Up until 2003 the closure bond for Strongman Mine was only $930, and both SENZ and the West Coast Regional Council (WCRC) agreed that a more realistic level of bonding was required.   A conceptual closure plan has been developed by Golder Associates, and the cost of the work estimated. Closure includes decommissioning of equipment and facilities, rehabilitation and replanting of all disturbed areas and a period of maintenance and monitoring to verify that closure objectives have been met. Significant maintenance allowances are included to cover management of underground fire, subsidence and slope instability. These make up much of the potential ongoing environmental liability at the Strongman. All costs incurred beyond year 1 of closure are discounted to present value. Uncertainty in costs is addressed by Monte Carlo simulation, with an 80 % confidence level adopted.   A bond quantum of $3.0 million has been calculated for the first year of closure at Strongman. A three-year ærollingÆ bond is proposed. Progress will be reviewed annually, with the bond adjusted up or down accordingly. It is then renewed for a further three years. This allows for progressive return of the bond as rehabilitation objectives are met and verified. Similarly, if there are delays in meeting objectives, a proportion of the bond may need to be kept in place for a longer period than assumed. The level of bonding in place for the Strongman operation at any time in the future will therefore reflect the cost to complete the closure work programme.

Jan 1, 2004

By Muir D. M

Highly saline process water has a number of implications for the CIP process during the leaching, adsorption and recovery of gold. The reduced oxygen solubility in saline water can seriously reduce the rate of gold leaching, while dissolved oxygen meters do not necessarily reveal actual oxygen concentrations in saline water. High levels of magnesium in the ground water necessitate operation at lower pH (-9), with the potential for greater cyanide loss via HCN stripping. In addition increasing salinity renders viscosity modifiers largely ineffective.The adsorption capacity of aurocyanide onto activated carbon is improved with increasing salinity, but misleading results can be obtained in assessment of gold loading kinetics of plant carbon samples already loaded, or partially loaded, in saline water if subsequently tested in fresh water. Elevated chloride levels in the Zadra elution process can cause severe anode corrosion in the elecuowinning cell. The Anglo elution process is tolerant to only slight increases in water salinity, but elution times can be reduced by ethanol addition. Care is required in carbon regeneration, as salts can catalyse carbon decomposition as well as increase kiln corrosion.

Jan 1, 1994

By Nguyen G. H, Graham J

A laboratory-scale fluidised-bed roaster has been used to examine the effect of temperature and duration of roast on the morphology of the calcine produced from a pyritic gold-bearing concentrate. Two mechanisms of oxidation, which depend on the roasting temperature, have been identified. For samples roasted below 550°C, direct oxidation of the sulphide occurred to form hematite with a porous fine-grained concentrically-layered texture. The surface area of the calcine increased with an increase in roasting temperature in the range 400 to 500°C. For samples roasted above 550°C, the first reaction was the evolution of sulphur vapour to produce pyrrhotite, which underwent increasing grain growth as the roasting temperature was increased. This had the effect of decreasing the surface area of the calcine. The pyrrhotite was subsequently oxidised to produce hematite.Leaching studies using cyanide solution indicated that gold extraction around 95 per cent was achieved at temperatures of 500°C and above, with optimum extraction, taking into account rate and cyanide consumption in the range 550 - 700°C. Hence recovery did not decrease with decrease in surface area of the calcine. Observed gold in leached calcines was mainly enclosed in thin oxide walls of the hematite, with minor quantities enclosed in quartz and silicate minerals.

Jan 1, 1995

Projects to be undertaken in remote locations require special attention with regard to constructability from the very first stages of design. This is to ensure not only that the project is compatible with the environment in which it' is proposed to be built, but that it does not require facilities or special construction equipment and expertise that is not available in the proposed location. This paper draws on experiences gained on projects in Alaska, Northern Canada, South East Asia, outback Australia, and more recently Bougainville, in Papua New Guinea, where over the past 5 years Minenco has undertaken in excess of A$120 million of work on a number of different projects for Bougainville Copper Limited Although many of these projects have been close to large populous cities, which have been served by regular shipping and airline services, the locations have not had the availability of construction facilities which exist in major cities of Australia and thus can only be considered as remote locations by current day standards. As a result, every nut bolt and washer has had to be brought to the job site by the construction company. No hardware or electrical warehouses existed for those forgotten half dozen high tensile bolts, spring

Jan 1, 1986

The areas of impact when employing high productivity long wall systems are reviewed and the financial implications of the most significant areas highlighted. A distinction has been made between availability and utilization. The need for more efficient delay recording, together with increasing control and utilization of the systems has been identified and the measurability of the latter discussed. The increased use of electronic delay reporting direct from the operating unit as the basis for operational control and a pre-emptive maintenance philosophy is seen as an important area of achieving higher performances from existing long wall production systems and Configurations.

Jan 1, 1988

The value of water is defined by its marginal utility. Challenges arise where the marginal utility is difficult to estimate. Therefore, when two or more interested parties wish to access water and they cannot use commensurate units for marginal utility; other means of value comparison must be sought. It is asserted here that sustainability principles can be used to guide this valuation if this is supported by a transparent decision framework. This paper proposes that the ICMM sustainable development principles provide appropriate guidance. In addition, a generic framework for decision making is suggested as a complement. Indicators of water management are recognised widely as an integral part of the accountability of minerals companies towards meeting sustainability goals. Less widely recognised are the ways in which sustainability principles can be used to guide decisions on water management which demonstrate growing awareness of its value. This paper illustrates the use of this logic in water issues associated with global sustainability challenges. It then goes on to demonstrate, using examples, that these links exist at all levels of the minerals industry and that indicators of this type are potentially as powerful as those currently being used. The reason for this is that the path from cause to effect is transparent and direct.

Jan 1, 2006

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

Corrosion is a chemical or electro-chemical attack on a metal by the surrounding medium, and it can be stated in general terms that a non-corrodible metal possesses that property either because there is no chemical action between it and the medium, or because the medium reacts quickly with the metal to produce a thin protective coating.When iron or steel is attacked by dilute mineral acids, for example, the products of the reaction are soluble and the formation of a protective film cannot take place; on the other hand, rusting produces a porous film which flakes away and offers little protection to the underlying metal. However, when chromium is alloyed with iron, its resistance to corrosion is improved because the films produced on such alloys become more adherent and tenacious as the proportion of chromium is increased. Chromium is thus an essestial constituent of the corrosion- and heat-resisting steels.During the 40 years which have elapsed since their initial development, these alloys have made an important place for themselves in in<lustry and commerce, and it is the object of this paper to 'describe typical examples of the many types which are available; also, to give some indication of their particular properties, and applications in the mining industry.NOMENCLATUREVery few of the alloys which are about to be described can strictly be considered stainless, and most are not steels in the sense that they can he hardened by quenching from...

Jan 1, 1951

The Lennard Shelf is an Upper Devonian carbonate reef complex striking northwest for 350 km along the northeast margin of the Canning Basin. Numerous small Mississippi Valley type (MVT) Pb-Zn prospects occur within this belt, including the Wagon Pass prospect, located 105 km east of Derby in the Napier Range. At Wagon Pass, the base of the Upper Devonian sequence is a cobbly, dolomitic sandstone, the Van Emmerick Conglomerate. This is conformably overlain by the Frasnian to Famennian Pillara cycle Lower Napier Formation fore-reef deposits. These are characterized by red algal wackestones and terrigenous stylo- bedded packstones, with common dolomitization. The conformably overlying Famennian Nullara cycle contains a classic reefal assemblage, consisting of flat lying Nullara Limestone back-reef, fore-stepping massive Windjana Reef, and steep basinward dipping Upper Napier Formation marginal slope. The Nullara cycle is not dolomitized. The Wagon Pass mineralization is hosted by Lower Napier Formation dolomite. Mineral- ization consists of complex intergrowths and semi-massive assemblages of sphalerite and galena, with subordinate pyrite, marcasite, chalcopyrite, bornite, digenite, covellite and bravoite. Ore textures include granular and colloform. Gangue minerals are dolomite and very fine grained green chloritic clay. Although mineralization commonly occurs as reticulate fracture fillings, its overall distribution is stratabound. Ore paragenesis involved early "diagenetic" dolomitization, followed by breccia formation with chloritic and granular dolomite matrices. Main stage galena-sphalerite mineralization then occurred, accompanied by pervasive chloritization of silty units. Ore genesis was probably related to basin-derived "oil field" brines, with open space textures in the mineralization quite comparable to textures seen in Canning Basin dolomitic hydrocarbon reservoirs. Fluid inclusions in the host dolomite have typical MVT homogenization temperatures of 70-1150 C, and contain minor organic phases. The Van Emmerick Conglomerate, with its high porosity, dolomitization and weak Pb-Zn anomalism, was probably the aquifer for the mineralizing brines. Access of ore solutions to the Wagon

Jan 1, 1986

By J J. Cilliers, K Hadler

Froth structure and stability are known to play important roles in determining mineral flotation recovery and selectivity. However, measuring froth stability in a consistent manner remains a significant challenge, especially at an industrial scale. Following preliminary tests on a copper concentration plant, a quantitative dynamic stability measure is investigated in this study in order to extend the results over a wider range of conditions and on a different orebody. The technique is based on the Bikerman foam test and uses a non-overflowing froth column to quantify froth stability. Experiments were carried out using an automated version of the froth stability column under different operating conditions. Air flowrate was the key operating variable. Tests were reproduced on a single flotation cell of a Platinum Group Metals concentrator. The froth stability factor, , was measured for each operating condition, and compared with the air recovery in the cell, , which was measured using image analysis. The froth stability column results gave the same trends as image analysis. In particular the froth stability factor was found to be linearly related to the actual fraction of air overflowing the cell. The metallurgical results clearly indicated that changes in air flowrate result in variations in flotation performance that can be attributed to changes in froth stability. The results showed that high froth stability conditions occur at intermediate air flowrates, and result in improved flotation performance. It is found that the froth stability column is a simple, cost-effective and reliable method for quantifying froth stability, and for indicating changes in flotation performance.

Jan 1, 2005

By Van Weert G

Ferrous chloride solution pyrohydrolysis is a successful IICI regeneration process which is carried out in either a spray roaster or a fluid bed. Pyrohydrolysis is not restricted to ferrous chloride only, every metal chloride can theoretically be hydrolysed. In practice, however, the conditions for ferrous chloride pyrohydrolysis differ from those of many non-ferrous metal chlorides eg zinc, lead and cadmium. Hence, a pyrohydrolyser could function as a ferrous/non-ferrous separator, eg an iron oxide and zinc chloride separator. Most pyrohydrolysers operate on solutions, in which case more than 50 per cent of the process energy is needed for heating and evaporating water. However, this disadvantage would be diminished by feeding a slurry to the reactor. Against this background it was decided to investigate the chloridisation of zinc ferrite which is an iron bearing solid with a non-ferrous impurity, and subject to processing and disposal problems. Synthetic zinc ferrite was chloridised in a tube furnace. The gas atmosphere in the tube furnace resembled that of a fluid bed pyrohydrolyser and consisted of HCI, 1120 and nitrogen. Gas composition, temperature, residence time and sample mass were varied. The experiments showed that complete (99.6 per cent) zinc extraction from synthetic zinc ferrite was possible in a simplified pyrohydrolyser atmosphere at 1100 K in four hours. The zinc ferrite was converted into gaseous zinc chloride, and hematite and magnetite solids. It was also found that zinc removal from the zinc ferrite lattice caused not only rccrystallisation of the zinc ferrite into hematite, but also hematite crystal

Jan 1, 1993