Search Documents

Although the diesel engine is normally considered a tried and proven power source, many new and exciting diesel design concepts are being evaluated in engine development laboratories around the world. Three such programs currently underway at Cummins Engine Company are discussed. The turbocompound engine converts into power exhaust heat energy which is normally wasted. It does this by incorporating after the turbocharger a low pressure gas turbine which is gear driven to the crankshaft. The adiabatic engine has no conventional cooling system. It converts into useful power most of the heat energy normally rejected to the coolant. The series boost turbocharged engine uses seperate low and high pressure turbochargers to increase engine output and improve transient performance. These design concepts make possible increases in diesel engine thermal efficiency from the current 33 to 38 per cent range to the 50 percent range.

Jan 1, 1982

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of a gangue mineral grade limits by the concentrator may also result in significant penalties. Online grade analysers which can provide reliable real-time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades. MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at a nickel concentrator plant. The project initially focused on stabilising the final concentrate grade without directly accounting for nickel recovery. The site later procured additional Blue Cube MQi analysers, resulting in the expansion of the FloatStar Grade-Recovery Optimiser to incorporate recovery component in the performance. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser.CITATION:Mantsho, S M, Phillpotts, D and Strobos, P, 2012. The implementation of FloatStar grade-recovery optimisation control solutions using Blue Cube online grade analysers on industrial flotation circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

One of the most frequently asked questions at the feasibility study stage of a project is, æhow big can one go?Æ This important question effects costing and efficiency of metallurgical equipment, the real estate required and the operating plant strategy.The presentation covers both engineering and process considerations and explains the limits that exist today and explores future trends.The paper is specific about large slurry application usually found in gold applications; however, it could apply to silver and uranium or other dense media leach duties.Agitator drive sizes are examined as well as process risks associated with large tank agitation. New technology has increased the maximum tank size and designers are now experienced in tank volumes in excess of 5000 m3. Tanks of 6000 m3 have been agitated and 10 000 m3 tanks are within present engineering know-how and scale-up.Fabrication techniques for shaft and impeller designs exceed the existing standards and new specifications will be needed to cover large mixer design. The paper covers certain aspects of mechanical design and proposes alternative standards that are more appropriate. Process considerations such as fluid natural frequency as well as typical superficial velocities for efficient operations are examined. Scale-up techniques based on existing and new technology are also examined to ensure a successful installation.The presentation therefore covers the majority of large mixer design questions that are frequently asked.

Jan 1, 2006

By Royston D

Victoria has an extensive brown coal resource, 202,000 Mt, of which 43,300 Mt is regarded as readily recoverable. This brown coal is located principally in the Latrobe Valley as thick seams and is being extracted at low cost primarily to support base-load electrical power generation. The high moisture content of the coal is partially off-set in many applications by the high reactivity of the coal and the generally low levels of potential pollutants such as ash, sulphur and nitrogen in the coal. Large scale development of this brown coal resource began in the 1920's. In addition to electricity generation, it is used for briquette production, carbonisation of briquettes to char and was gasified for town gas supply to Melbourne (1956 - 1969). The BCLV coal to oil pilot plant at Morwell is a major new initiative in the use of Victorian brown coal. Many other new developments are in place and emerging in the utilization of low rank coals. Examples of these developments are, the large-scale gasification of lignites in the USA, and value-added products such as bulk chars, solid fuels, activated carbons and coal-water mixtures. The Government of Victoria has created the Coal Corporation of Victoria to promote current sales of briquettes and to encourage further new industrial developments based on the State's brown coal resources, in particular the Loy Yang coalfield. The Coal Corporation also has a vigorous product and process oriented research and development Programme.

Jan 1, 1987

By M Boyd

The University of Wollongong was named University of the Year 2000, for its work in preparing students for the e-world. Computer facilitated learning is being introduced into subjects throughout the engineering course. First year mining engineering students are introduced to computers, e-communication, using the UniversityÆs web based information system, and web based subject delivery. Mining engineering students in the mid-years of the course use programming languages and numerical computation software such as MATLAB, while students in the final years use a range of commercially available professional engineering software such as TALPAC. Most of these subjects are offered as part of the UniversityÆs Learning Online program, co-ordinated by its Centre for Educational Development and Interactive Resources (CEDIR). Learning Online subjects are delivered using the Web Course Tools (WebCT) environment. WebCT allows all resources to be accessed through the web, allows email communication between lecturer and student, and allows discussion groups for the exchange of ideas. Students can submit their assignments through WebCT and receive immediate feedback. This paper describes how WebCT has been used to deliver a first year engineering computing subject, mid-year numerical computation subjects, a mining economics subject and mine planning subjects.

Jan 1, 2002

The commercial outcomes from new mining projects or brownfields expansions often fall short of feasibility study forecasts because of technical under-performance. This paper: reviews past feasibility study performance; identifies the key drivers of underperformance; and proposes actions that can be taken to manage the risk of underperformance. There have been a number of published reviews of feasibility study performance since the 1970s. The results of these studies are summarised together with recent unpublished data. Key drivers of underperformance include inadequate metallurgical testing, simultaneously pushing a number of project parameters beyond comfortable limits and a failure to recognise the linkage between mining rate and head grade. Actions can be taken during the data acquisition phase and during the feasibility study to manage project technical risks. These generally require a more flexible approach to study management than can be achieved under a ælump sumÆ contract.

Jan 1, 2003

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

A system of decline mine entries and ore haulages has been designed for the Mt. Windarra mine. This choice was controlled by the nature of the ore- bodies, the mining method chosen and the capital cost of development re- quired for production. Mine entries are being driven 4 metres high and 5.5 metres wide and decline at 11%, to accommodate diesel haulage vehicles of 35 tonnes capacity. The.Mount Windarra haulage system and the design parameters used in its selection and design are discussed, and general design and selection parameters are proposed.

Jan 1, 1973

By W Farnworth, D Fergusson

Estimation of productivity is a key factor in the design of hydraulic mines and in assessing their economic feasibility. A published Russian formula for hydraulic mining monitor cutting rates overstated productivity by up to 2 tonnes per minute (251%) when applied to Solid EnergyÆs hydraulic mines. A new formula, taking into account additional productivity factors, was derived by Solid Energy and produced an acceptable correlation between predicted and actual cutting rates inNew Zealand and overseas hydraulic mines, with an average error of approximately 0.1 tonnes per minute.   Another key factor in hydraulic mine design is the transport of coal slurry via flumes. Solid Energy carried out a series of 80 full scale tests in a surface flume installation, varying the gradient and coal:water ratio. Both steel flumes and plastic-lined flumes were evaluated. A modification of the Chezy Open Channel Flow formula, including a factor for slurry density, gave a reasonable correlation between actual and predicted flows. It is believed that this Solid Energy formula is suitable for the design of flume installations for hydraulic mining.

Jan 1, 2004

Chlorine as a lixiviant for gold possesses a number of significant chemical and Idnetic advantages over cyanide but because of its corrosive and vaporous nature the method of implementation needs to be significantly modified. At comparable reagent concentrations the dissolution rate for gold in the C12/Cl- systems is some 10 - 100 times that achieved in the 02/CN system. The dissolution rate in the chlorine system is largely a function of the concentration of C12, Cl- and pH. Under conditions of low Cl', (less than 50 g/1), the dissolution rate begins to drop off dramatically over the pH range from 3 - 4. Increasing the level of dissolved chloride ions shifts the pH of this rate reduction to around pH 5 at 100 g/l NaCl, and to around pH 6 at 300 g/l NaCl.

Jan 1, 1991

The Australian mining industry can expect to be working internationally competitive high quality coal mines during the twenty-first century. Cost efficient mining methods such as high productivity longwall units with heavy reliance on remote control will be standard and worked by well paid and intensively trained operators. Major changes in mine ventilation engineering can be expected in the use of computers and mine telemetry, the understanding of the mine environment and the frequency of mine disasters, the utilization of mine air contaminants for profitable purposes and the provision of a pleasant and comfortable work environment. New approaches to mine ventilation such as air recirculation will have been considered. There will be an increased need for highly trained ventilation engineers. With the present pace of technological change, quite revolutionary new approaches to mining and ventilation can be expected by the end of the twenty-first century.

Jan 1, 1988

By B Roache, A Vakili, R Talebi

When a highly anisotropic or weak rock mass is subjected to high-stress conditions, it can lead to large ongoing deformations or squeezing ground conditions. Squeezing ground conditions can impose increased support costs, delays associated with rehabilitation, and disruption to production schedules. Ultimately, in more severe cases, it may result in complete drive closure. Several recent case studies investigated the squeezing mechanism and measures to control squeezing ground in underground mines and also to design appropriate ground support systems. Effective management of squeezing ground conditions requires a sound understanding of the failure mechanism and the driving forces. Once the failure mechanism is understood, the appropriate ground support system should be tailored to specifically manage the critical driving forces that control the squeezing mechanism. Support type, support stiffness, reinforcement length, support density, installation times and mining sequence all have important impact on the effectiveness of the support system. This paper provides a case study at the Ballarat Gold Mine in Australia, where drive squeezing was associated with foliated ground conditions located below 700 m depth. Numerical modelling was used to better understand the failure mechanism and the driving forces that lead to squeezing conditions. The effectiveness of various support types was compared to installed ground support performance. This has provided a credible methodology for assessing and optimising the selection of reinforcement in squeezing ground conditions. CITATION:Talebi, R, Roache, B and Vakili, A, 2018. Understanding and modelling squeezing ground conditions at the Ballarat Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 107–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By V Sahajwalla, S Shin

Research activities to classify the quality of iron oxides have a long history but most of such activities are for the existing processes such as blast furnace or DR plant. Therefore the newly developed process, such as the COREX process, needs new standardisation although some basic functions of the new process have similarity to the existing processes. Many researchers (Hauk, 1990; Cho et al, 1998) in the field of COREX process have conducted investigations since the early stages of the process development and activities are underway for further plant optimisation. As Agrawal and Oshnock (1995) pointed out, because coke is not included in the COREX reduction shaft the strength requirement of the feed materials in COREX process will be more demanding than that in the blast furnace. This condition is similar to Midrex DR plant but the main reduction gas of COREX plant is carbon monoxide generated from coal combustion while that of Midrex DR plant is hydrogen from natural gas.

Jan 1, 2000

By Lawson F

Chrome chemicals are commercially produced by the alkali roasting of the chrome-bearing ore chromite with sodium carbonate. In order to ascertain the influence on the extent of reaction of the replacement of Mg(II) for Fe(II) in the chromite spinel structure and the presence of acidic oxides in the gangue material, a series of roasting experiments was conducted using chromite materials from a number of different locations. The roast feeds and products were chemically analysed and the major compounds identified using X-ray diffraction and scanning electron microscope techniques.Mg(II) replacement for Fe(II) in the chromite structure does not appear to restrict the amount of "available" chromium for reaction.Under the test conditions, namely an atmosphere of pure oxygen, finely ground chrome-bearing material, a roast temperature of 950°C and the stoichiometric amount of sodium carbonate to react with the chromite, the yield of water-soluble sodium chromate was able to be expressed as %yield = 104.5 -1.58 × %AI2O3 - 2.23 × %SiO2 for chromite samples containing alumina in the range 7.8 to 27.8 per cent and silica in the range 2.9 to 7.4 per cent.

Jan 1, 1984

By S J. Henderson

Over much of Australia, rainfall is highly seasonal and storm-driven. Consequently, operational mines often need extensive earthworks – drains, dams and levees – for protection during the occasional large floods and for water storage against the dry times; however, it has not been appreciated that many of these earthworks will need to function after mining has finished, sometimes, beyond a normal design life for engineered structures.While a mine is operating, standards for design and maintenance are dictated by regulation and risk assessment. For dams and levees – regulated structures – the standards imposed mainly relate to life-of-mine. The levels of risk and maintenance accepted by the mine operator may not be acceptable to another landholder in perpetuity. However, the Environmental Authority cannot be surrendered unless the landholder has accepted responsibility for any unrehabilitated regulated structures (Department of Environment and Heritage Protection (DEHP), 2016).In order for a future landholder to be willing to take responsibility for a dam or levee, the structure should be of value to the business of the property. In addition, its management needs must be consistent with that business; for example, it should be maintainable using skills, equipment and materials normally available to the business.CITATION:Henderson, S J, 2016. Earthworks or landforms? Designing for lease surrender, in Proceedings Life-of-Mine 2016 Conference , pp 151–153 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Rixon LK, Walton KP

Evidence will be presented to show that borescope inspection of mine roofs is one of the most useful techniques available for stability assessments. ACIRL currently has four borescopes, comprising two fibre-optic units of 2.7 m and 4.5 m length and two optical rod units (introscopes) 6 m and 8 m in length. (The 8 m unit is not yet fully operational because of modifications needed to meet safety regulations). Using the fibre-optic units, photographs of hole walls or ends can be taken to record features. Roof lithology and crack patterns can be observed in roof holes from 25 - 60 mm in diameter. Several crack parameters are useful: type, location in the roof with respect to height and lithological boundaries, presence of individuals or zones containing crack clusters and the estimated amount of dilation. These data are readily computer- plotted to form "borescope logs". Provided that the holes remain open, a hole or group of holes can be re-surveyed at intervals to monitor crack development across or along a roadway, for example with respect to an advancing blind-ended roadway face.

Jan 1, 1986

By J Jackson, M F. Young

"Ore is the economic portion of a mineral deposit that can be extracted economically. Hence an ore type is a classification of the ore based on one or more dominant characteristics in order to enable communication between unit operations and/or technical disciplines.In project evaluation, ore types are often defined early based on geological observations by geologists and initial metallurgical testing is based around this classification even though a number of processing options can be under evaluation. However, the geological drivers of performance for each of these processes can be very different and the ore type classification for one process may not be relevant for another. In operations an ore type, as either defined in the project evaluation phase or those that evolve with additional knowledge, is unlikely to provide the knowledge required across all the unit operations. The ore type has a meaning to someone but does not necessarily for all unit operations across the value chain.Geometallurgical or orebody knowledge has evolved through the consideration of multiple processes within the value chain, the improved understanding of variability of process performance within ore types and the effect on the complexity of the mineral extraction processes. Furthermore orebody knowledge has been moving from personal based knowledge and understanding to a more process oriented approach where measurement and spatial and process performance modelling is playing a greater role. Advances in mine planning and scheduling allow for both detailed analysis of the block model and the expected extraction processing attributes across various time scales. This capability of analysing and describing the complexity still requires to be communicated to the various unit operations, which may be beyond the traditional classification of an ore type.The limitations of an ore type and potential alternatives to enable the relevant information to be communicated to the relevant groups are outlined through a number of case examples across the value chain.CITATION:Jackson, J and Young, M F, 2016. Ore Type – Everything to Someone but Nothing to Anyone, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 267–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Eren H

For a hydrocyclone of fIXed geometry, DC, Di, DO and ? are constants, the variable parameters affecting the performance are Qi, Fi, Du and H. (See Appendix 2 for definition of symbols).The relationship between d50c, Qi, Fi, Du and H gives models which can effectively be used for performance predictions. Such models have already been established by Lynch et al and by Plitt.These models have been tried in a limited manner under continuous operating conditions for on-line cowol. For on-line control effective and accurate instrumentation is required for which a new set up is proposed. Using this set up, a new model was established. A feature in this model is that deviations from the norm of operational parameters affecting d50c were considered. It is shown that these deviations generated by the disturbance of one or more of variations in the parameters, can be monitored by a computer and suitable signals generated to control servo mechanisms for restoring the required d50c value.The logic followed in developing the computer software is described and the application of the model is indicated.

Jan 1, 1990

Nickel laterite HPAL circuits are known for their complexity and have presented a large number of challenges to process engineers worldwide. An attitude commonly encountered by the author is that the beneficiation of the ore is relatively simple and that the difficult problems are in the realms of hydrometallurgy. On a number of occasions beneficiation has become the 'poor cousin' in the process design phase. Another common theme is that significant difficulties are encountered when beneficiation circuits are started up, invariably slowing the ramp-up of the remainder of the circuit. In some cases the problems impact on throughput for a long period and can require major rectification capital. The HPAL Ni laterite projects encountered each have their own set of beneficiation problems that need to be understood before an appropriate circuit can be designed. This paper will discuss a range of design issues including geometallurgy, ore characterisation through laboratory testing, the application of appropriate sizing and analytical procedures, the selection of appropriate unit operations, materials handling of plant feed and products and setting meaningful plant design requirements.

Jan 1, 2008